|
|
|
|
|
BALL JOINT KITS |
QK4591L
Super Duty Ball Joint Kit
Tech Note: Ford designed the knuckle
seal so it will be damaged when the axle shafts are removed. We strongly advise that you
order the correct Knuckle Seal Kit along with your ball joint set.
|
Original Equipment 4x4 Ball Joints for
your
2005-up F250, F350, F450, and F550 Super Duty trucks with Dana 60 Monobeam
axle are Made in U.S.A.. Standard Kit includes 4 ball
joints with hardware, cotter keys for the tie rod ends, ball
joint installer sleeves, Threadlocker, anti-seize, disc brake
caliper lube, and instructions. Choose either
Factory Lubed, or Greaseable ball joints.
|
QK4591L Kit with Installers and factory lubed ball
joints $249.95
|
|
QK4592L Kit with factory lubed ball joints, but No
Installers $199.95
|
|
QK4591LG Kit with Installers and Greaseable ball joints
$299.95
|
|
QK4592LG Kit with Greaseable ball joints, but No
Installers $249.95
|
|
|
Knuckle Seal and Tool Kit
The installer is also available separately
from our Ford Tools Page and 4x4tools.com
|
2005-up
Super Duty Knuckle Seal Kit includes our heavy-duty T1530 or
T1531
Knuckle Seal Installer, Knuckle Seals, wheel hub to knuckle
o-rings and lockout hub o-rings.
Seal replacement is required anytime the axle shaft is removed
to prevent vacuum leaks and or water infiltration. Use the
T1530 (F250-F350) or T1531 (F450/550) for damage free
installation of the knuckle seal on the outer axle shaft and
then use it to seat the axle shaft assembly in the knuckle to
the proper depth.
|
|
QK4637
Super Duty Knuckle Seal Kit
|
2005
Super Duty Knuckle Seal Kit includes Knuckle Seals, wheel hub to knuckle o-rings,
hub snap rings and
lockout hub o-rings.
Seal replacement is required anytime the axle shaft is removed
to prevent vacuum leaks and or water infiltration. Knuckle seals
require installation tool QT1530 or QT1531. (See next block for Knuckle
Seal descriptions.)
| Available Soon!
|
| Available Soon!
|
|
|
Individual Parts: |
|
|
Pressing Knuckle seal on Outer Axle Shaft.
Tool bottoms against axle shaft when seal is at proper location
on axle shaft |
Knuckle Seal Installation
Ford knuckle seals are the toughest
seals to install we have ever come across. The seal is of
a complicated unitized design that is easily damaged without the
correct installer. In fact the knuckle seal is virtually
impossible to install without damage unless a tool like our
one piece, rugged QT1530 and QT1531 Knuckle Seal Installer is used
to drive or press the seal on. Not
only is the seal an extremely tight fit to the shaft, it also
must be installed to a specific depth on both the axle shaft and
in the knuckle. A damaged seal will allow water to
enter and vacuum to escape. Our QT1530 and QT1531 Knuckle Seal
Installers can be purchased separately from our
Ford Tools page or
4x4tools.com
|
Seating Axle Shaft in Knuckle with T1515.
Tool stops when seal is at
correct depth |
|
AXLE UNIVERSAL ADD-ON KITS
|
 |
Axle
U-Joint Kits Choose from either
hot-forged
greaseable, or PREMIUM COLD_FORGED non-greaseable and cold-forged greaseable
axle u-joints. These are the best production u-joints of
their type that we have ever found. For more
information, pricing, and to order, go to our
Common Front Axle
Parts Page.
Kits for 2005-up F-250, F350, Trucks with Model 60 Monobeam Front Axle
To Order, Go To
Common Front Axle
Parts Page
QK4521 Hot Forged
Greaseable
QK4525
PREMIUM
Cold Forged
Non-Greaseable
QK4581
PREMIUM Cold Forged Greaseable
|
|
AXLE SHAFTS |
|
|
Axle Shafts are original equipment
replacements for worn or broken shafts for your
|
|
SEALS AND SMALL PARTS |
|
Outboard Seal Set |
Outboard Axle Shaft to Axle Housing Seals
press on inner shaft next to the yoke. It's function is
to keep dust and debris from entering the axle housing tubes.
Made in U.S.A. Includes two seals.
|
|
Inner Axle Seal Kit
|
Inner Axle Seal Set fits all 2005-2008 Super Duty front drive
axles. Quickly and easily press in new inner axle seals
without damage! Installation tool cups the seal so force
is only applied on the outer shell. Kit includes seal
installer, thrust plate, press screw assembly, 2 seals, and
instructions. Tool made in U.S.A. Seals made in Canada.
|
|
|
|
|
