|
Successfully Installing Inner
Axle Shaft Seals without damaging the seal or
axle can be a real witch without the right tools
for the job. The unique design of our
Axle Seal Installers fully supports the seal and
protects it from damage during installation. |
|
Please
Read:
All our Inner Axle Seal Installers are of necessity made to
fit a specific brand and part number of seal.
Inner axle seals are among the most difficult of
any seal to install due to very tight fits and
restricted access. To work successfully,
each installer must be precision machined to
match a specific seal design. You can buy
the seals from us, the vehicle dealer, or
anyone else who supplies original equipment
parts, but whatever you do, always use our
installers with the correct seal.
As a rule, aftermarket Inner Axle Shaft Seals as
purchased from parts stores are
NOT compatible with
our tools! |
|
T1002
Fits:
QU40165
Seal Mfr: NOK
Dodge p/n: 4506005
1-5/8" Shaft Size
2-9/32" Seal OD
Axles: Dana 44, 60
Use T1002 With:
T1048A Rod
T1047 or T1092 Plate |
T1002 is our most popular Inner Axle Seal
Installer. It is used on most 1988-2001 Dodge
full-size trucks with Central Axle Disconnect to install
the QU40105 original equipment NOK made seal for the large diameter
disconnect axle shaft. (See T1114 for
installer for CR made seal for same applications)
$49.97
or Save $5
by purchasing
Online for only $44.97!
Left Axle Shaft Applications for
Dodge:
1988-1993 Ramcharger, W150, and W250 (gasoline
engine only)
Right Axle Shaft Applications for Dodge:
Dodge:
1994-2001 Ram 1500
Dodge: 1994-1999 All Ram 2500 and Ram 3500 trucks
 |
QU40105 Seal $6.98 |
|
|
|
|
|
|
|
T1029
Fits:
QU40159
Seal Mfr: NOK
Dodge p/n: 4116366
1-5/16" Shaft Size
2-9/32" Seal OD
Axles: Dana 44, 60
Use T1029 With:
T1048A Rod
T1047 or T1092 Plate
|
T1029 It is used most commonly on 1985-2001 Dodge
full-size trucks with Central Axle Disconnect (CAD) to
install the QU40159 original equipment NOK made seal for the small
diameter non-disconnect axle shaft. Several other
vehicles used the same NOK Seal (See
T1084 for installer for CR made seal for same
applications) $49.97
or Save
$5
by purchasing
Online for only $44.97!
Right Axle Shaft Applications for
Dodge with CAD:
1985-1993 Ramcharger, W150, and W250 (gasoline
engine only)
Left Axle Shaft Applications for Dodge with CAD:
Dodge: 1994-2001 Ram 1500
Dodge: 1994-1999 All Ram 2500 and Ram 3500 trucks
Both Left & Right Applications on Non-Disconnect
Axles
Chevy/GMC: 1970 K20/25
Chevy/GMC: 1978-1980 K5, K10/15, K20/25 w/model 44
axle
Dodge: 1977½-1984
Ramcharger W-150, W-250
Ford: 1979 F-150 Super Cab, F-250 (Model 44 Axle
only)
Jeep: 1978-1985 Wide Track Full Size Cherokee
Jeep: 1978-1987J10, J20
|
QU40159 Seal $6.98 |
|
|
|
T1041
Fits:
QU40055
Seal Mfr: CR
GM p/n: 6273977
1-5/16" Shaft Size
2-9/32" Seal OD
Axles: Dana/Spicer 44
Use T1041 With:
T1189 Rod
T1161 Plate |
T1041 installs the QU40055 current design original equipment CR
made seal in
many older 4x4 trucks with Dana-Spicer Model 44 axles.
Our T1041 has a depth stop making it easy to install these seals to the
correct depth every time. (Also see T1165) $59.97
or Save
$6
by purchasing
Online for only $53.97!
Applications:
Chevy/GMC: 1973-1977 K5, K10
Chevy/GMC: 1972-1977 K20
Ford: 1967-1969 F-250
Ford: 1975 -1977 F100, F150, F250
Ford: 1976-1977 Bronco
Dodge: 1972½-1977
W100, W200
Dodge: 1974-1977 Ramcharger
IHC: 1973-1978 Scout II
IHC: 1971½-1975
1100, 1200 (except 1200 Heavy Duty)
Jeep: 1974-1977 Cherokee, Wagoneer, J10, J20
 |
QU40055 Seal 7.95 |
|
|
|
T1042
Fits:
QU40059
Seal Mfr: NOK
Dodge p/n: 3894131
Ford p/n: D8TZ3254A
GM p/n: 462857
1-9/16" Shaft Size
2-5/8" Seal OD
Axles: Dana/Spicer 60, 61
Use T1042 With:
T1133 Rod
T1130 Plate |
T1042 allows you to install the QU40059 original
equipment NOK inner axle seals on most 1970's-1990's
Model 60 and 61 axles to different depths. This
feature is especially useful when the axle shafts are
grooved by the old seals. (Also see
T1156) $52.97
or Save
$5
by purchasing
Online for only $47.97!
Applications:
Chevy/GMC: 1977-1991 K30, K35, K3500 V3500
Chevy/GMC: 1984-1988 Military CUCV
Dodge: 1975-1993 W300, W350
Dodge: 1989-1993 W250 with Cummins Diesel
Ford: 1978-1979 F-250 Heavy Duty, F-350
Ford: 1985-1992 F-350
IHC: 1975 1300 Camper Special
 |
QU40059 Seal $8.50 |
|
|
|
T1070
Fits:
QU40271
Seal Mfr: CR
Dodge p/n: 5015198AA
1-59/64" Shaft Size
2-59/64" Seal OD
Axle: Dana/Spicer 60
Use T1070 With:
T1148A Rod
T1131 or T1092 Plate |
T1070 is used to install the QU40171 Right Axle Shaft
Seal on 2000-early 2002 Dodge Ram 2500 and 3500 trucks with
Central Axle Disconnect (CAD). Works with original
equipment CR seals. $64.97
or Save
$6
by purchasing
Online for only $58.97!
Applications:
Dodge: 2000-early 2002 all 2500 & 3500 with CAD
 |
QU40271
Seal $12.95 |
|
|
|
T1071
Fits:
QU40298
Seal Mfr: CR
Dodge p/n: 5015201AA
1-15/32" Shaft Size
2-59/64" Seal OD
Axle: Dana/Spicer 60
Use T1071 With:
T1148A Rod
T1131 or T1092 Plate |
T1071 is used to install the QU40298 Left Axle
Shaft Seal on 2000-early 2002 Dodge Ram 2500 and 3500 trucks
with Central Axle Disconnect (CAD). Installs both left
and right seals on all 2002 Dodge 2500 and 3500 trucks
without CAD. Works with original equipment
CR seals.
$64.97
or Save
$6
by purchasing
Online for only $58.97!
Applications:
Dodge: 2000-2002 Left Seal on all 2500 & 3500
Dodge: 2002 Right Seal on all 2500 and 3500
without CAD
 |
QU40298 Seal $12.98 |
|
|
|
T1079
Fits:
QU40057
Seal Mfr: NOK
Jeep p/n: 8121781
1-3/16" Shaft Size
2-1/8" Seal OD
Axle: Dana/Spicer 30
Use T1079 With:
T1189 Rod
T1186 Plate |
T1079 Installs the early style QU40057 NOK seal on
Jeep CJs. 5/8" Center Hole $42.97
or Save
$4
by purchasing
Online for only $38.97!
Applications
Jeep: 1972-1977 CJ
 |
QU40057 Seal $8.95 |
|
|
|
T1080
Fits:
QU40098
Seal Mfr: NOK
Jeep p/n: 83503504
1-5/8" Shaft Size
2-1/8" Seal OD
Axle: Dana/Spicer 30
Use T1080 With:
T1107A Rod
T1081 Plate |
T1080
makes installing the QU40098 Right Axle Shaft Seal on 1987-1996
Jeep Cherokee (XJ) and Wrangler (YJ) front axles
with vacuum controlled Central Axle Disconnect (CAD)
easy. Made to fit the original NOK seal
(Jeep p/n 83503504) 1/2"
center hole $42.97
or Save
$4
by purchasing
Online for only $38.97!
Applications:
Jeep: 1987-1991 Cherokee/Comanche (XJ) with CAD
Jeep: 1987-1996 Wrangler (YJ) with
CAD
 |
QU40098 Seal $8.95 |
|
|
|
T1084
Fits:
QU40159
Dodge p/n: Unknown
Seal Mfr: CR
1-5/16" Shaft Size
2-9/32" Seal OD
Axles: Dana 44, 60
Use T1084 With:
T1048A Rod
T1047 or T1092 Plate |
T1084 Installs a CR manufactured QU40270 seal in the
applications that originally used a NOK made seal . The
48489 was also original equipment on some 1999 Dodge 2500 and
3500 trucks and 1999-2001 Dodge 1500 models. (See
T1029 for installer for NOK made seal for same
applications)
$49.97
or Save $5
by purchasing
Online for only $44.97!
Right Axle Shaft Applications for
Dodge with CAD:
1985-1993 Ramcharger, W150, and W250 (gasoline
engine only)
Left Axle Shaft Applications for Dodge with CAD:
Dodge: 1994-2001 Ram 1500
Dodge: 1994-1999 All Ram 2500 and Ram 3500 trucks
Both Left & Right Applications on Non-Disconnect
Axles
Chevy/GMC: 1970 K20/25
Chevy/GMC: 1978-1980 K5, K10/15, K20/25 w/model 44
axle
Dodge: 1977½-1984
Ramcharger W-150, W-250
Ford: 1979 F-150 Super Cab, F-250 (Model 44 Axle
only)
Jeep: 1978-1985 Wide Track Full Size Cherokee
Jeep: 1978-1987J10, J20
 |
QU40270 Seal $10.50 |
|
|
|
T1089
Fits:
QU40307
Seal Mfr: NOK
Jeep p/n: 4874477
1-3/16" Shaft Size
2-1/8" Seal OD
Axle: Dana 30
Use T1080 With:
T1107A Rod
T1081 Plate |
T1089 Installs the current production left side
QU40307 NOK seal on
most smaller Jeeps with Central Axle
Disconnect (CAD) 1/2" Center Hole $42.97
or Save
$4
by purchasing
Online for only $38.97!
Left Axle Shaft Applications for Jeeps with CAD:
Jeep: 1984-1991 Cherokee (XJ)
Jeep:
1987-1996 Wrangler (YJ)
 |
QU40307 Seal $5.95 |
|
|
|
T1114
Fits:
QU40326
Seal Mfr: CR
Dodge p/n: 4506005AB
1-5/8" Shaft Size
2-9/32" Seal OD
Axles: Dana 44, 60
Use T1114 With:
T1048A Rod
T1047 or T1092 Plate |
T1114 Works on most 1988-2001 Dodge
full-size trucks with Central Axle Disconnect to install
the QU40326 late production, original equipment, Chicago Rawhide
(CR) manufactured seal for the large diameter disconnect axle
shaft. (See T1002 for installer for NOK
made seal for same applications)
$49.97
or Save $5
by purchasing
Online for only $44.97!
Left Axle Shaft Applications for Dodge:
1988-1993 Ramcharger, W150, and W250 (gasoline
engine only)
Right Axle Shaft Applications for Dodge:
Dodge: 1994-2001 Ram 1500
Dodge: 1994-1999 All Ram 2500 and Ram 3500 trucks
 |
QU40326
Seal $9.97 |
|
|
|
T1138
Fits:
QU40382
Seal Mfr: NOK
Dodge p/n: 3827533
IHC p/n: 893911 R91
1-1/2" Shaft Size
3" Seal OD
Axle: Dana/Spicer 70
Use T1138 With:
T1133 Rod
T1130 Plate |
T1138
Installs the original QU40382 NOK Inner Axle Seals on 1960's
-1970's Dodge and International trucks with Dana Model
70 front axles. $52.97
or Save
$5
by purchasing
Online for only $47.97!
Applications:
Dodge: 1967-1975 W300
Dodge: 1974-1978 W600
IHC: 1968½-1975
1300
IHC: 1967-1978 1600
 |
QU40382 Seal
$13.48 |
|
|
|
T1139
Axle:
Dana/Spicer 30
Use T1139 With:
T1189 Rod
T1186 Plate |
T1139 Installs the current production
QU40307 NOK seal on
most smaller Jeeps with and without Central Axle
Disconnect (CAD) 5/8" Center Hole $42.97
or Save
$4
by purchasing
Online for only $38.97!
Left Axle Shaft Applications for Jeeps with CAD:
Jeep: 1984-1996 Cherokee (XJ), Wrangler (YJ)
Both Left & Right Applications on Non-Disconnect
Axles
Jeep: 1978-1986 CJ
Jeep: 1984-2002 Cherokee/Comanche (XJ),
Wrangler (TJ, YJ), Grand Cherokee, small Wagoneer,
Grand Cherokee (ZJ)
| For seal specs and to order QU40307 Seal,
see T1089 above. |
|
|
|
T1156
Axle: Dana/Spicer 60, 61
Use T1156
With:
T1133 Rod
T1130 Plate |
T1156 Is used install the original equipment NOK
inner axle seals on most 1970's-1990's Model 60 and 61
axles to a fixed depth. Permits, fast and
fool-proof installation. (Also see T1042)
$83
or Save over
$8
by purchasing
Online for only $74.97!
Applications:
Chevy/GMC: 1977-1991 K30, K35, K3500 V3500
Chevy/GMC: 1984-1988 Military CUCV
Dodge: 1975-1993 W300, W350
Dodge: 1989-1993 W250 with Cummins Diesel
Ford: 1978-1979 F-250 Heavy Duty, F-350
Ford: 1985-1992 F-350
IHC: 1975 1300 Camper Special
| For seal specs and to order QU40059 Seal,
see
T1042 above. |
|
|
|
T1165
Axles:
GM 10 Bolt
Use T1165
With:
T1133 Rod
T1186 Plate
Dana 44
Use T1165 With:
T1189 Rod
T1161 Plate |
T1165
works to install CR seals on many older trucks with
Dana 44 axles and all GM trucks with the GM 10 bolt
solid front axle. This tool does not have a
depth stop making it suitable for use on both Dana 44
and GM 10 bolt applications, so you will need to check
the depth of the old seals before removing them.
GM always used a CR seal for the 10 bolt, but many Dana
axles were originally equipped with an NOK seal which
Spicer has replaced with the CR design. (Also see
T1041 for Mod 44) $49.97
or Save $5
by purchasing
Online for only $44.97!
Applications:
Chevy/GMC: 1977-1991 Blazer, Jimmy, Suburban with GM
10 Bolt
Chevy/GMC: 1977-1987 K10/15/1500, V1500 with GM
10 Bolt
Chevy/GMC: 1977-1987 K20/25/2500, V2500 with GM
10 Bolt
Chevy/GMC: 1973-1977 K5, K10
Chevy/GMC: 1972-1977 K20
Ford: 1967-1969 F-250
Ford: 1975 -1977 F100, F150, F250
Ford: 1976-1977 Bronco
Dodge: 1972½-1977
W100, W200
Dodge: 1974-1977 Ramcharger
IHC: 1973-1978 Scout II
IHC: 1971½-1975
1100, 1200 (except 1200 Heavy Duty)
Jeep: 1974-1977 Cherokee, Wagoneer, J10, J20
| For seal specs and to order QU40055 Seal,
see
T1041 above. |
|
|
|
Individual Inner Axle Seal
Installers
For 1993-1997 Ford F-350 and 1999-up Ford Super Duty
(Dana 50 & 60 Monobeam Axles) |
 |
T1126
Fits:
QU40244
Seal Mfr: Forsheda
Ford p/n: 2C3Z3254AA
1-9/16" Shaft Size
2-5/8" Seal OD
Axles: Dana 50, 60
Use T1126 With:
T1133 Rod
T1129 Plate (Mod 50)
T1130 Plate (Mod 60) |
T1126 A low cost tool that installs the original
equipment QU40244 Forsheda
made oil bath type seal on 1993 and newer Ford trucks
with solid front axles. This installer will work
on both Model 50 and Model 60 axles. Since there
is no depth stop, you need to check the tool depth
during installation. (When the Seal
is at the proper depth, the rear face of the tool will
be approximately flush with the axle bore face on a
Model 50, and protrude out from the face about 0.200" on
the Model 60). We also make Installers with
depth stops for these axles, see T1127 and T1128
$59.97
or Save $6
by purchasing
Online for only $54.97!
Applications:
Ford: 1993-1997 F-350
Ford: 1999-current Excursion, F-250, F-350,
F-450, F550
 |
QU40244 Forsheda
OEM Oil Bath Type Seal $19.95 |
|
|
|
T1127
Axle: Dana/Spicer 50
Use T1127 With:
T1133 Rod
T1129 Plate |
T1127 Installs the original equipment QU40244 Forsheda made oil bath type
seal to the correct depth on 1999-2004 Ford Excursion
Super Duty F-250 and F-350 Single Rear Wheel
trucks equipped with the Model 50 axle.
(from 2002-2004, most if not all
F-250/350 Diesel trucks used a Model 60 axle)
We also make an Installer without a depth stop for this
axle, see T1126 $73
or Save over $7
by purchasing
Online for only $65.97!
Applications:
Ford: 1999-2004 Excursion, F-250, F-350SRW all
with Model 50 axle
| For seal specs and to order QU40244 Seal,
see
T1126 above. |
|
|
|
T1128
Axle: Dana/Spicer 60
Use T1128 With:
T1133 Rod
T1130 Plate |
T1128 Installs the original equipment QU40244 Forsheda made oil bath type
seal to the correct depth on 1993-1997 Ford F-350,
2005-current F-250, and 2000-current Super Duty F-350
Dual Rear Wheel, F-450 F-550 trucks equipped with the
Model 60 axle. Also installs the seals on all 2002-2004
F-250 and F-350SRW with the Model 60 axle
(primarily Diesel trucks used the Model 60 for 2002-2004
F250, F350 SRW) We also make an Installer
without a depth stop for this axle, see T1126
$83
or Save over
$8
by purchasing
Online for only $74.97!
Applications:
Ford: 1993-1997 F-350
Ford: 2002-2004 F-250, F-350SRW (only those with
Model 60 axle)
Ford: 2000-current F350DRW, F-450, F550 |
|
|
Axle End Plates for Jeep and Dodge 4x4's
with Central Axle Disconnect (CAD)
Goes against end of axle tube to center and anchor
installer pull rod. |
 |
T1047
is made to fit 1994-2001 Dodge Axles with 2-1/8" Axle
Tube inside diameters. 5/8" ID center hole.
(Also see T1092) $22
or Save over
$2
by purchasing
Online for only $19.97!
Applications:
Dodge: 1988-1993 Ramcharger, W150, W250
(gasoline engine)
Dodge: 1994-1999 Ram 2500, 3500
Dodge: 1994-2001 Ram 1500 |
|
 |
T1081 Double step plate for 1984-1996 Jeeps with
CAD fits both small and large ID axle tubes. 1/2" ID
center hole. $27
or Save over
$2
by purchasing
Online for only $24.97!
Applications:
Jeep: 1984-1996 Cherokee/Comanche (XJ), Wrangler (YJ) with
CAD |
|
 |
T1092 A Double Step Plate that works on all
1988-2002 Dodge
full size trucks with Central Axle Disconnect. Can be
used in place of both T1047 and T1131. 5/8" ID center
hole. $35
or Save over
$3
by purchasing
Online for only $31.97!
Dodge: 1988-1993
Ramcharger, W150, W250 (gasoline engine)
Dodge: 1994-2002 Ram 2500, 3500
Dodge: 1994-2001 Ram 1500 |
|
 |
T1131 is made to fit 2000-2002 Dodge Axles with
2-3/4" Axle Tube inside diameters. 5/8" ID center
hole. (Also see T1092)
$27
or Save over
$2
by purchasing
Online for only $24.97!
Applications:
Dodge: 2000-2002 Ram 2500, 3500 with CAD |
|
|
Thrust Plates for Axle Seal Installation
Plate fits against Differential Bore Face when pressing
in opposite axle seal on axles without Central Axle
Disconnect. (All Thrust Plates
have 5/8" ID center holes) |
 |
T1129 fits Dana Model 50 monobeam axles used on
most 1999-2004 Ford Excursion and Super Duty F-250,
F-350 Single Rear Wheel trucks. $29
or Save over
$2
by purchasing
Online for only $26.97!
Applications:
Ford: 1999-2004 Excursion, F-250, F-350SRW all
with Model 50 axle |
|
 |
T1130 Fits all Dana Model 60, Super 60, 61, and
Closed Knuckle Model 70 axles from 1967-current. $32.97
or Save
$3
by purchasing
Online for only $29.97!
Applications:
Chevy/GMC: 1977-1991 K30, K35, K3500 V3500
Chevy/GMC: 1984-1988 Military CUCV
Dodge: 1967-1975 W300
Dodge: 1974-1978 W600
Dodge: 1975-1993 W300, W350
Dodge: 1989-1993 W250 with Cummins Diesel
Ford: 1978-1979 F-250 Heavy Duty, F-350
Ford: 1985-1992 F-350
Ford: 1993-1997 F-350
Ford: 2002-2004 F-250, F-350SRW (only those with Model
60 axle)
Ford: 2000-current F350DRW, F-450, F550
IHC: 1968½-1975
1300
IHC: 1967-1978 1600
IHC: 1975 1300 Camper Special |
|
|
|
T1161
Fits all Dana Model 44 solid front axles |
|
|
|
T1186 Works
with GM 10 Bolt solid front axles |
|
Axle Seal Press
Designed for axles without Central Axle Disconnect |
 |
T1133
Press Screw Assembly
(T1189 Similar) |
T1133
Press Screw Assembly for Dana/Spicer Model 50, 60, 61, 70,
and GM 10 Bolt Axles. Use with the appropriate Seal Installer and
Thrust Plate for your application. $45
or Save over
$4
by purchasing
Online for only $40.97! |
|
|
T1189
Press Screw Assembly for Dana/Spicer Model 30 and 44 Axles. Use with the appropriate Seal Installer and
Thrust Plate for your application. $44
or Save over
$4
by purchasing
Online for only $39.97! |
|
Seal Installation Pull Rod for CAD Axles
Dodge and Jeep Applications for both left and
right seals |
 |
 |
T1048A Pull Rod for all
1988-2002 Dodge full size models with Central Axle
Disconnect. Rod is used to pull Axle Shaft Seals
into place in conjunction with the appropriate Axle Seal
Installer and Axle End Plate. 5/8" diameter. $25
or Save over $2
by purchasing
Online for only $22.97! |
|
 |
T1107A Pull Rod for all
1984-1996 Jeep XJ and YJ models with Central Axle
Disconnect. Rod is used to pull Axle Shaft Seals
into place in conjunction with the appropriate Axle Seal
Installer and Axle End Plate. 1/2" diameter. $22
or Save over $2
by purchasing
Online for only $19.97! |
|
|
|
A Note About Interchanging Seals:
Whenever possible, it is recommended you use the
original seal design, however, it is often possible to
consolidate multiple tools and seals to one size.
Due to the many axle variations it is impossible for us
to state any particular seal will ALWAYS replace another
seal. The following list is provided for reference
only of possible substitutions.
QU40105 |
|
QU40326 |
QU40159 |
|
QU40270 |
QU40057 |
|
QU40307 |
| |
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
|
