Front Axle Parts for 1994-1997 Dodge Ram 2500 4x4 Trucks with Dana-Spicer Model 44

The Dana-Spicer, Model 44 216 Front Beam-Design Iron (FBI) axle was used on all 1994-1997 gas V8 powered, light duty, Ram 2500 trucks with Gross Vehicle Weights (GVW) under 8800 pounds. If you have a gas 8800 pound or higher GVW Ram 2500 truck, or one with either the Cummins Diesel or V10 engine, then you have a Model 60, so refer to our 1994-1999 or 2000-2002 Model 60 pages. Tech Note: The GVW is listed on the build tag located on the door frame. If you have a 1994-2001 Ram 1500, please refer to our 1994-2001 Dodge Ram 1500 Front Axle web page for your axle.

Like 1985-1993 Dodge Model 44 axles, all the Dana 44 front axles used in light-duty 1994-1997 Dodge Ram 2500 4x4's were factory equipped with a vacuum actuated Central Axle Disconnect (CAD) system.

Axle Identification

top_page
photo

All 1994-2001 Dodge Ram 2500 Dana-Spicer Model 44 Front Axles in Dodge Ram trucks had a Bill of Material Number (BOM) stamped on a Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows) when the vehicle was shipped from the factory. The BOM number is a 6 digit number beginning with a 6 plus a dash number (ex: 610604-2). They can be used to determine not only the axle model, but also what components the axle was originally built with. We often ask for this number to insure we provide you with the exact parts you need for your truck.

Each different BOM number signifies an engineering part change which may be minor or major and may involve one or more parts. Unfortunately, these tags are often missing on trucks that had prior differential service dash number indicates the axle ratio.
For 1994 Ram 2500 3.54 ratio is a -4, 3.92 ratio is -1, 4.09 ratio is -2
For 1995-1997 Ram 3.54 ratio is a -1, 3.92 ratio is -2, and 4.10 ratio is -3

photo

Cover: 10 Bolt, 10-3/8" high

Suspension: Coil spring

Ball Joints: Pressed in axle C Forging, nuts at bottom.

Dodge Ram 2500
Dana Model 44
Front Axle
Bill of Material Numbers by Year
 1994: 610423, 610425
 1995: 610513, 610515, 610538,
 1996: 610513, 610603, 610613, 610615
 1997: 610632, 610634
 1998-2002: Model 44 was not used, see our Model 60 Pages for 1994-1999 and 2000-2002

Axle Shafts

top_page
product note

Genuine Original Equipment (OEM) Axle Shafts for your 1994-1997 light duty Dodge Ram 2500 4x4s'. These axle shafts fit all and light duty, gas V8 powered Ram 2500 models under 8800 Gross Vehicle Weight (GVW). Replace your broken shafts today! Shafts Made in Mexico, U-Joints Made in U.S.A. Shaft Assemblies are Assembled in U.S.A.

Important!
See Below about interchangeability of Anti-lock Brake System (ABS) axle shafts with non-ABS outer axle Shafts!

tech note

Dan the Gear Man® Tech Note 1:
The only difference between ABS and non-ABS axles is ABS outer shafts have a pressed on cast tone ring/slinger which was used on 1994-1997 trucks with external ABS sensors, while non-ABS outer shafts had a tin slinger. Our Outer Axle Shafts have ABS tone rings so they will fit both ABS or non-ABS axles. So even though the tone ring may look different than what you have, it will seamlessly interchange with absolutely no problems for fit or function.
Dan the Gear Man® Tech® Note 2:
Over the years, Dana Engineers have made two significant design changes to the threaded end of QU40325 Outer Axle Shafts (Click Here to See Image of Thread Changes). The first change was to shorten the thread length about 3/8" by removing the threads from the outer end of the Axle Shaft. (From the Cotter Key hole out is now un-threaded). By doing so, the chances of stripping threads when removing the nut are reduced. The second change was to flatten a portion of the remaining threads to function as a locking feature. So don't be alarmed when you see an area of mashed looking threads on your new axle shaft that looks like somebody whacked it with a hammer. According to Dana engineering, this is to provide greater resistance to the nut backing off. The Torque specification remains unchanged and you must still use a Cotter Key.

photo

QU40325 Outer Axle Shaft for Dodge Ram 2500 Replaces either the left or right outer axle stub shaft on your 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500 and 1997 Dodge Ram 2500 light duty (under 8800 Gross Vehicle Weight), gas V8 powered 4x4 trucks with or without 4 wheel ABS. Includes tone ring/slinger, 33 splines. Genuine original equipment part. Made in Mexico.

Important!
See below about interchangeability of Anti-lock Brake System (ABS) axle shafts with non-ABS outer axle Shafts and Axle Shaft Design Changes!

photo

QU40308 Right Inner Axle Shaft For Dodge Ram 2500. QU40308 Right Inner Axle Shaft is the center axle shaft on the passenger side of your Dodge Ram. Inner end has 15 splines for the CAD coupler, outer end is a yoke for the axle u-joint. QU40308 Right Inner Axle Shaft fits all 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500 and 1997 Dodge Ram 2500 light duty (under 8800 Gross Vehicle Weight), gas V8 powered 4x4 trucks with or without four wheel ABS. Includes QU40107 bushing. 15 splines. Genuine original equipment part. Made in Mexico

photo

QU40383 Left Inner Axle Shaft for Dodge Ram 2500 QU40383 Left Inner Axle Shaft is splined on the inboard end to fit the differential side gear and has a yoke on the outboard end for your axle u-joint. Fits all 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500 and 1997 Dodge Ram 2500 light duty (under 8800 Gross Vehicle Weight), gas V8 powered 4x4 trucks with or without four wheel ABS. 30 splines. Genuine original equipment part. Made in Mexico

photo

QK4838 Left (Drivers Side) Axle Shaft Assembly For Dodge Ram 2500. Fits all 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500 and 1997 Dodge Ram 2500 light duty (under 8800 Gross Vehicle Weight), gas V8 powered 4x4 trucks with or without four wheel ABS. Complete Shaft Assembly includes: QU40325 30 spline Outer and QU40383 33 spline Inner Axle Shafts, TK40712 U-Joint, ABS Tone Ring/Slinger, and QU40362 Dust Seal for Inner Axle Shaft.

Important!
See below about interchangeability of Anti-lock Brake System (ABS) axle shafts with non-ABS outer axle Shafts and Axle Shaft Design Changes!

photo

QK4837 Right (Passenger Side) Axle Shaft Assembly For Dodge Ram 2500. Fits all 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500 and 1997 Dodge Ram 2500 light duty (under 8800 Gross Vehicle Weight), gas V8 powered 4x4 trucks with or without four wheel ABS. Complete Shaft Assembly includes: QU40308 15 spline Inner and QU40325 33 spline Outer Axle Shafts, TK40712 U-Joint, ABS Tone Ring/Slinger, QU40107 Support Bushing (pressed in Inner Shaft), and QU40362 Dust Seal for Inner Axle Shaft.

Important!
See below about interchangeability of Anti-lock Brake System (ABS) axle shafts with non-ABS outer axle Shafts and Axle Shaft Design Changes!

photo

QU40333 Differential Output or Intermediate Axle Shaft for Dodge Ram 2500. Fits all 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500 and 1997 Dodge Ram 2500 light duty (under 8800 Gross Vehicle Weight), gas V8 powered 4x4 trucks with or without four wheel ABS. 30 spline inner end goes into the differential side gear, 15 spline outer end matches splines on QU40246 CAD Clutch Collar. Genuine original equipment part. Made in Mexico

Limited Supply

photo

QK4732 Axle Shaft Nut and et for Both Sides fits the outer stub axle shafts on all 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500 and 1997 Dodge Ram 2500 light duty (under 8800 Gross Vehicle Weight), gas V8 powered 4x4 trucks

photo

QK4732.5 Shaft Nut and Washer Set for One Side Fits the outer stub axle shafts on all 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500 and 1997 Dodge Ram 2500 light duty (under 8800 Gross Vehicle Weight), gas V8 powered 4x4 trucks

Axle Universal Joints

top_page
product note

We offer two different Universal Joints for your hard working Dodge Ram Truck. Both are good, reliable products, but different manufacturing techniques and seal types will have a major influence on the ultimate life of the joint. Our most popular choice is our TK40712 cold-forged, non-greaseable, original equipment replacement U-Joint. The wear-resistant cold-forged cross and superior sealing make it the best choice for both low maintenance and long life. QU40754 are hot-forged and are equipped with simple rubber seals. They are greaseable through a flush fitting threaded into one of the caps. With good maintenance and quality lubricant like our Pyroplex® Plus Grease, these joints will last and last. Click on the Part Number Links to see our individual product pages for more info.

photo

TK40712 Torque King® Axle U-Joint Premium quality, cold-forged, factory lubed U-Joint for stock QU40325, QU40308 and QU40383 shafts. The crosses are cold forged and solid. This axle universal joints fits all these gas V8 powered Dodge Ram trucks with less than 8800 pound GVW: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500

photo

QU40754 Axle U-Joint Greaseable Axle Shaft U-joint fits stock QU40325, QU40308 and QU40383 shafts on all these gas V8 powered Dodge Ram trucks with less than 8800 pound GVW: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500. This U-Joint is no longer available. Order TK40712 below

Ball Joints

top_page
product note

Ball Joint QUADKIT™ for Model 44 (216FBI) 1994-1997 light duty 3/4 ton gas V* powered Dodge Ram 2500 4x4's under 8800 pound GVW. Replace those worn ball joints on your Ram light duty Ram 2500 series Dodge Truck yourself! Each kit includes: 4 genuine original equipment replacement Ball Joints with hardware, Cotter Keys for aftermarket tie rod ends, axle shift unit, Gasket, Threadlocker, Anti-Seize, RTV Sealant, and Synthetic Brake Caliper Lube. Ball Joint Sockets Made in Canada, rest of the Kit components Made in U.S.A.

photo

Ball Joint Kits 1994-1997 Light Duty Dodge Ram 2500 Series 4x4's Ball Joint QUADKIT™ for Model 44 (216FBI) 1994-1997 light duty 3/4 ton gas V* powered Dodge Ram 2500 4x4's under 8800 pound GVW. Replace those worn ball joints on your Ram light duty Ram 2500 series Dodge Truck yourself! Each kit includes: 4 genuine original equipment replacement Ball Joints with hardware, Cotter Keys for aftermarket tie rod ends, axle shift unit, Gasket, Threadlocker, Anti-Seize, RTV Sealant, and Synthetic Brake Caliper Lube. Ball Joint Sockets Made in Canada, rest of the Kit components Made in U.S.A

photo

QK4693 Ball Joint Kit For 1994-1997 Ram 2500 Light Duty 4x4's. QK4693 Ball Joint Kit fits the outer stub axle shafts on all 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500 light duty (under 8800 Gross Vehicle Weight), gas V8 powered 4x4 trucks Each QK4693 Ball Joint Kit includes: 4 genuine original equipment replacement Ball Joints with hardware, Cotter Keys for aftermarket tie rod ends, axle shift unit, Gasket, Threadlocker, Anti-Seize, RTV Sealant, and Synthetic Brake Caliper Lube.

photo

QU40234 Dana OEM Upper and Lower Ball Joint Set for 1 side for 1994-1999 Dodge Ram 1500 and 1994-1997 Dodge Ram Dana 44 4x4 front axles.

More Info

CAD Individual Parts (Central Axle Disconnect)

top_page
photo

QU40317 CAD Axle Shift Housing for 1994-1997 Dodge Ram 2500 Light Duty 4x4's Genuine original equipment aluminum housing to replace broken or damaged housings on your Ram 4x4 QU40317 Axle Shift Cover or Housing fits these gasoline powered Dodge Ram 2500 4x4 with Gross Vehicle Weights under 8800 pounds: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500.

photo

QU10966 CAD Disconnect Switch for Dodge Ram 4x4's Genuine original equipment indicator switch screws into QU40317 housing. Also order QU10967 O-Ring. This switch will send a signal to your 4x4 indictor light when the front axle is is locked into 4x4 mode. QU10966 CAD Switch fits these gasoline powered Dodge Ram 2500 4x4 with Gross Vehicle Weights under 8800 pounds: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500

photo

QU10967 O-Ring for CAD Switch Use this O-Ring to make a leak-proof seal between your CAD Indicator Switch (QU10966 ) and CAD Housing (QU40317 ). QU10967 O-Ring fits these gasoline powered Dodge Ram 2500 4x4 with Gross Vehicle Weights under 8800 pounds: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500

photo

QU40107 Axle Shaft Bushing for Dodge Ram Disconnect Axle Shaft Is a very common part to wear out. This genuine, original equipment bushing fits inside the inner end of your right inner axle shaft (QU40308 ). It is the only direct support for right axle shaft assembly besides the wheel hub

photo

QU40292 Support Bearing for Dodge Ram Intermediate Shaft On early production (1994-1997) Model 44 front axles in Dodge Ram 4x4 trucks This bearing was used to support the Intermediate Shaft (QU40333 ) Later production (1997.5 and up) axles used plastic QU40320 bushing which is totally interchangeable with this bearing. QU40292 Bearing is located in your right axle tube, just to the left of the rectangular CAD opening. This genuine original equipment, press-fit bearing supports the splined end of the differential output (what Dodge calls the intermediate shaft)

photo

QU40246 CAD Clutch Collar couples the differential output shaft and right axle shaft when you activate Four Wheel Drive QU40320 fits these gasoline powered Dodge Ram 2500 4x4 with Gross Vehicle Weights under 8800 pounds: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500

photo

QU50048 Clamp for Axle Vent Hose original equipment type, 1-ear clamp is used to secure the axle vent hose to the axle breather located on the CAD housing

photo

QU40156 CAD Shift Fork Pad is a genuine original equipment part. Two of these Pads are included with every QK4628 CAD Shift Fork. QU40156 fits fits these gasoline powered Dodge Ram 2500 4x4 with Gross Vehicle Weights under 8800 pounds: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500

photo

QU40090 Metal Reinforced Central Axle Disconnect Gasket Fits all gas V8 powered Dodge Ram trucks with less than 8800 pound GVW: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500

CAD Parts and Tool Kits (Central Axle Disconnect)

top_page
photo

QK4627 CAD Small Parts Kit includes: QU40090 CAD Gasket, QU40272 O-Ring, 2 QU40156 Shift Fork Pads, QU50048 Hose Clamp, and the 3 E-Clips for the original equipment motor and fork mounting.

Dan the Gear Man® Tech Note: The two smaller E-Clips supplied in this Kit fit the original equipment actuator shaft. Most aftermarket shafts have at least one groove that is machined to a smaller diameter. The original equipment clips supplied in this Kit will not fit those smaller diameter grooves.

photo

QK4628 CAD Shift Fork Kit fits all gas V8 powered Dodge Ram trucks with less than 8800 pound GVW: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500 4x4 trucks. Kit includes genuine, cast iron original equipment fork and two shift fork pads

photo

QK4904 Vacuum Shift Kit For Dodge Ram with Central Axle Disconnect fits all gas V8 powered Dodge Ram trucks with less than 8800 pound GVW: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500 4x4 trucks. Kit includes: U.S.A. made vacuum actuator, QK4627 CAD Parts Kit, and new retaining bolts and lock washers

photo

QK4646 Right Axle Shaft Bushing Kit for CAD Axles fits all gas V8 powered Dodge Ram trucks with less than 8800 pound GVW: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500 3/4 ton, 1996 Dodge Ram 2500 3/4 ton, and 1997 Dodge Ram 2500 3/4 ton 4x4 trucks. Kit includes 1 QU40320 bushing and 1 QU40107 bushing. Early production trucks used QU40292 bearing instead of QU40320 bushing for the output shaft, if you prefer a bearing instead of a bushing for the intermediate shaft, See QK4625

Differential & Pinion Dana Original Equipment Bearing Cup & Cones

top_page
photo

QU50533 Timken® Outer Pinion Bearing Cup For 1994-1997 Dodge Ram 2500 with Dana-Spicer Model 44 Front Axle 4x4 trucks. This is a First Class, original equipment quality bearing cup that meets or exceeds all vehicle manufacturer specifications making it the top choice for heavy-duty applications like yours

photo

QU50534 Timken® Outer Pinion Bearing For 1994-1997 Dodge Ram 2500 with Dana-Spicer Model 44 Front Axle 4x4 trucks. This is a First Class, original equipment quality bearing that meets or exceeds all vehicle manufacturer specifications making it the top choice for heavy-duty applications like yours

photo

QU50539 Timken® Inner Pinion Bearing Cup For 1994-1997 Dodge Ram 2500 with Dana-Spicer Model 44 Front Axle 4x4 trucks. This is a First Class, original equipment quality bearing cup that meets or exceeds all vehicle manufacturer specifications making it the top choice for heavy-duty applications like yours

photo

QU50540 Timken® Inner Pinion Bearing For 1994-1997 Dodge Ram 2500 with Dana-Spicer Model 44 Front Axle 4x4 trucks. This is a First Class, original equipment quality bearing that meets or exceeds all vehicle manufacturer specifications making it the top choice for heavy-duty applications like yours

photo

QU50537 Timken® Differential Bearing Cup For 1994-1997 Dodge Ram 2500 with Dana-Spicer Model 44 Front Axle 4x4 trucks. This is a First Class, original equipment quality bearing cup that meets or exceeds all vehicle manufacturer specifications making it the top choice for heavy-duty applications like yours

photo

QU50538 Timken® Differential Bearing For 1994-1997 Dodge Ram 2500 with Dana-Spicer Model 44 Front Axle 4x4 trucks. This is a First Class, original equipment quality bearing that meets or exceeds all vehicle manufacturer specifications making it the top choice for heavy-duty applications like yours

photo

QU40181 Differential Bearing Set For Dodge Ram with Dana-Spicer Model 44 Front Axle fits all gas V8 powered Dodge Ram trucks with less than 8800 pound GVW: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500 4x4 trucks

Differential Bearing & Seal Kits Featuring Genuine Dana-Spicer Parts

top_page
photo

QU50595 Differential Bearing and Seal Kit For 1994-1997 Dana 44 Beam Type Front Axles with crush sleeves

Differentials and Differential Parts

top_page
photo

QU30170U Loaded Differential Case For Dana 44 with 3.92 to 5.89 ratio gear sets and 30 spline axle shafts

QU40632 Empty Differential Case Kit For Dana Model 44 3.73 and numerically lower ratios. Includes ring gear bolts and diff shims

QU40633 Loaded Differential Case Assembly For Dana Model 44 3.73 and numerically lower ratios. Includes spider gears, diff bearings, ring gear bolts and diff shims

QU40634 Empty Differential Case Kit For Dana Model 44 3.92 and numerically higher ratios. Includes ring gear bolts and diff shims

QU40635 Loaded Differential Case Assembly For Dana Model 44 3.92 and numerically higher ratios. Includes spider gears, diff bearings, ring gear bolts, and diff shims

Gaskets and Gasket Makers

top_page
photo

QU40214 Mod 44 Cover Gasket For all Dana-Spicer Model 44 axles. Can be used instead of or in conjunction with RTV sealant.

Dan the Gear Man® Tech Note: Dana originally used RTV sealant to seal the differential cover on your Dodge Ram

photo

S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Dodge Ram front axle.

photo

QU40090 Metal Reinforced Central Axle Disconnect Gasket for Dodge Ram 4x4's QU40090 CAD Gasket also fits these gasoline powered Dodge Ram 2500 4x4 with Gross Vehicle Weights under 8800 pounds: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500.

Hub Assemblies and Parts

top_page
photo

QU11024 Hub to Steering Knuckle Bolt For all 1994-1997 Dodge Ram 2500 4x4 trucks with Dana 44 Front Drive Axles

Manuals and Technical Service Bulletins

top_page
photo

TSB4620 Inner Axle Seal Replacement

Miscellaneous Parts

top_page
photo

QU40114 Axle Shaft Nut Is a genuine original equipment replacement part. Also available in QK4732 Kit with the flat washer and cotter key

photo

QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound

Seals

top_page
photo

QU40105 NOK Brand Right Axle Shaft Seal Is a genuine original equipment NOK brand seal used for the Dodge Ram 2500 Dana 44 Right Axle Seal

photo

QU40159 NOK Brand Left Axle Shaft Seal Is a genuine original equipment NOK brand seal used for the Dodge Ram 2500 Dana 44 Left Axle Seal

photo

QK4620 Left and Right Inner Axle Seal Installation Kit includes installation tools and seals for both sides, plus gasket, and vent hose clamp.

 

photo

QK4631 Right Side Inner Axle Seal Kit includes right side installation tools and seal, plus gasket, and vent hose clamp.

photo

QU40362 Dodge Ram 2500 Dana 44 Outboard Axle SealThese Seals are installed on later production original equipment inner axle shafts right next to the u-joint yoke. When the axle shaft is installed, the face of the seal will seal against the end of the axle tube to keep dirt, dust, and crud from entering the axle housing tubes.

photo

QU40461 Dana 44 Pinion Seal for 1994 to 1999 Dodge Ram 2500 4x4 Is a genuine original equipment Pinion Seal

Small Parts

top_page
photo

QU50048 Breather Hose Clamp For Axle Vent Hose original equipment type, 1-ear clamp is used to secure the axle vent hose to the axle breather located on the CAD housing. Fits all 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500

photo

QU40246 Clutch Collar Fits all gasoline powered Dodge Ram 2500 4x4 with Gross Vehicle Weights under 8800 pounds: 1994 Dodge Ram 2500, 1995 Dodge Ram 2500, 1996 Dodge Ram 2500, and 1997 Dodge Ram 2500

photo

QU40208 Pinion Preload Spacer (Crush Sleeve). This Preload Spacer Genuine original equipment Collapsible Pinion Preload Spacer or crush sleeve fits between the inner and outer pinion bearings on many late 1980's and later Dana-Spicer Model 44 and axles. Replace anytime the pinion yoke is removed for any reason

Steering Tie Rods and Steering Parts

top_page
photo

QU10579 1994-1997 Dodge Ram Steering Shaft Clamp Bolt Two of these hardened metric Bolts are used on your Dodge truck's steering column to steering box shaft

Tools

top_page
photo

QT1033 Case Spreader Is used to relieve the differential bearing preload making it easy to safely remove and install your front differential without damaging expensive critical parts

photo

QT1072 Hub Puller Is used to remove the front wheel hubs for all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500 and 2002 Dodge Ram 2500 4x4 trucks and all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500 and 2002 Dodge Ram 3500 4x4 trucks.

photo

QT1200 Tie Rod Separator Allows you to remove the separate tie rod and drag link ends without wrecking the seals or screwing up your steering linkage ends

photo

QT9018 5 Pound Dead Blow Hammer Is just about the first tool you will reach for for a multitude of jobs on your Dodge Ram. From seating differentials to removing rusted-on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool