Closed Knuckle Standard Dana 44 Front Axle Parts in 1957-1971 Dodge 4x4 Power Wagon® Trucks

Dodge used 2 types of Dana 44 closed knuckle front axles in 1957-1971 W100 and W200 4x4 trucks. This page shows parts for 3000 pound capacity, Standard duty Dana 44 axles with 8 bolt Ball Seals which were used on 1/2 ton and light 3/4 ton models. If you have a 3500 pound capacity Heavy-Duty Dana 44 front axle with 12 bolt Ball Seals please see our Dodge Dana 44HD Closed Knuckle Parts Page.

Axle Identification

top_page
photo

Cover: 10 Bolt, 10-3/8" high

Suspension: Leaf spring

Axle Shafts

top_page
product note

1969-1970 W100 Closed Knuckle Front Axle Used Inner Axle Shafts are in really nice condition. We have a limited supply of both inner shafts. Shafts are measured from center of u-joint hole to end of spline. Shafts take a QU40507M internal c-clip universal joint. Hole diameter: 1.062", distance between yoke ears (lockup dimension) 2.188". If you have one of these classic vintage Dodge trucks, don't delay ordering because when these shafts are gone, they're gone!

photo
27656-7X Used Right Axle Shaft Dodge 38655446 Right 18½"
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
27656-8X Used Left Axle Shaft Dodge 38655447 Left 36-31/32"
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note

The Closed Knuckle Dodge Dana 44 axle uses solid cross, inside lock-up universal joints without seals that are designed to be bathed in a semi-liquid lubricant from inside the closed knuckle balls. By today's standards, these u-joints are way undersized, but given the lighter vehicle weights and modestly powered engines of the late 1950's to early 1970's, the joint size was probably adequate.

photo
QA40507 Axle Universal Joint for Dodge Dana 44 Closed Knuckle Front Axles is a genuine original equipment axle manufacturer, solid-cross, non-greaseable, front axle u-joint without seals for 1959-1971 Dodge Power Wagon® W100 and W200 4x4 trucks with the standard Dana 44 closed knuckle front axle

Link to our QA40507 Large Text Product Page.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Closed Knuckle Parts

top_page
product note

We stock the regular service closed knuckle parts for your 1959-1973 Dodge W-100 or W200 Power Wagon® 4x4 with a standard closed knuckle Dana 44 front axle which will have 8 bolt Knuckle Ball Hemisphere Seals. With a Closed Knuckle axle, the axle universal joints and king pin bearings are lubricated by very heavy oil or a viscous grease that will flow when the axle shafts rotate. A large multi-piece seal is bolted to the backside of the steering knuckle to keep lubricant in and water out. On poorly maintained closed knuckle axles or axles equipped with lockout hubs that are rarely used in 4x4, the upper king pin bearing and axle universal joint can suffer from lack of lubrication. The Ball Seals will usually weep some lubricant especially when standard gear oils are used as a lubricant. Submersion of the axle under water or condensation from temperature changes can cause moisture to build up inside the enclosed ball and lead to corrosion damage and part failures.

photo
QK4617 1957-1971 Dodge W-100, W-200 Dana 44 Closed Knuckle Front Axle Knuckle Bearing and Shim Kit Includes 4 Timken® Knuckle Bearings, 4 Timken® Knuckle Bearing Cups, and Rectangular Knuckle Shim Set to service both sides of your vintage Dodge W100 or W200 Power Wagon® 4x4 truck
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK50784 Torque® King Timken® Small Closed Knuckle King Pin Bearing Only Kit with Timken Bearings Includes 4 Timken® Knuckle Bearings and 4 Timken® Knuckle Bearing Cups for 1957-1971 Dodge W100 and W200 4x4 trucks with standard Dana 44 closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40773 Knuckle Shim Kit for 1957-1971 Dodge W-100, W-200 Dana 44 Closed Knuckle Front Axles with 8 Bolt Ball Seals Includes a selection of rectangular shims to adjust the Knuckle Bearing preload. One Kit services one side of your vintage Dodge W100 or W200 Power Wagon® 4x4 truck
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20091 and QU20092 Trapezoid Knuckle Shims For Many 1957-1971 Dodge W-100, W-200 Dana 44 Closed Knuckle Front Axles with 8 Bolt Ball Seals fit between the combination steering arm/upper king pin to adjust the turning preload for your vintage Dodge W100 or W200 Power Wagon® 4x4 truck drivers side steering knuckle
photo
QU40188 1957-1971 Dodge W-100, W-200 8 Bolt Knuckle Ball Seal Kit for Dana 44 Standard Front Axles Is a genuine original equipment Seal Kit for Dana 44 standard duty closed knuckle front axles in your vintage Dodge W100 or W200 Power Wagon® 4x4 truck
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50627 1957-1971 Dodge W-100, W-200 Dana 44 Closed Knuckle Timken® Knuckle Bearing Cup For Dana 44 Standard Duty closed knuckle front axles in your vintage Dodge W100 or W200 Power Wagon® 4x4 truck
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50628 1957-1971 Dodge W-100, W-200 Dana 44 Closed Knuckle Timken® Knuckle Bearing For Dana 44 Standard Duty closed knuckle front axles in to service both sides of your vintage Dodge W100 or W200 Power Wagon® 4x4 truck
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40564 Bronze Upper Knuckle Bushing with Key Slot Is a genuine original equipment replacement Bushing for all early production Dodge W-100 and W200 trucks with a standard Dana 44 closed knuckle axle that uses a upper King Pin with a key slot
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40569 Splined Bronze Upper Knuckle Bushing Is a genuine original equipment replacement Bushing for all mid to late production Dodge W-100 and W200 trucks with a standard Dana 44 closed knuckle axle with a splined upper King Pin
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU42009 Original Equipment 7/16" ID Tapered Locking Bushing Cone for Dodge Dana 44 Front Steering Arms Fits the steering arms on 1957-1971 standard Dodge W100 and W200 standard Dana 44 closed knuckle front axles with a trapezoid steering arm to steering knuckle bolt pattern
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings (Individual)

top_page
product note

There was a Dodge Dana 44 differential Side Bearing change which according to Dana was effective with at least some 1967 and 1968 model year vehicles. My Dodge parts books however, list the change over year as 1969 so you will need to verify your bearing size for 1967 and 1968 trucks.
All bearings are not created equal for fit or durability, so we only stock first class, long lasting, Timken® Differential and Pinion Bearings for your Dana front axle. Timken® was and is a a major original equipment supplier of top-notch bearing components to Dana Spicer. Since I first started rebuilding Dana axles in the mid 1970's, I have found Timken® Bearings to be the most consistent in relation to the published dimensions of any bearing on the market which makes rebuilding an axle right the first time a WHOLE lot easier!

photo
QU50533 Timken® Outer Pinion Bearing Cup For 1959-1971 Dodge Power Wagon® W100 and W200 4x4 trucks with the standard Dana 44 closed knuckle front axle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50534 Timken® Outer Pinion Bearing For 1959-1971 Dodge Power Wagon® W100 and W200 4x4 trucks with the standard Dana 44 closed knuckle front axle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50535 Timken® Inner Pinion Bearing Cup For 1959-1971 Dodge Power Wagon® W100 and W200 4x4 trucks with the standard Dana 44 closed knuckle front axle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50536 Timken® Inner Pinion Bearing For 1959-1971 Dodge Power Wagon® W100 and W200 4x4 trucks with the standard Dana 44 closed knuckle front axle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50538 Timken® Large Inside Diameter Differential Side Bearing For 1959-1971 Dodge Power Wagon® W100 and W200 4x4 trucks with the standard Dana 44 closed knuckle front axle that has differential side bearing with an inside diameter of 1.796". (uses 2)
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50683 Timken® Small Inside Diameter Differential Side Bearing For 1959-1971 Dodge Power Wagon® W100 and W200 4x4 trucks with the standard Dana 44 closed knuckle front axle that has differential side bearing with an inside diameter of 1.688". (uses 2)
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50537 Timken® Differential Side Bearing Cup For 1959-1971 Dodge Power Wagon® W100 and W200 4x4 trucks with the standard Dana 44 closed knuckle front axle. (uses 2)
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing and Seal Kits

top_page
photo
QU50576 Dana 44 Front Axle Differential Bearing and Seal Kit For mid 1960's-1971 Dodge Power Wagon® W100 and W200 4x4 trucks with the standard Dana 44 closed knuckle front axle that has differential side bearings with an inside diameter of 1.796".
See our QU50576 large text individual page for more details and tech notes

Differential Parts

top_page
photo
QU30170U Loaded Differential Case For Dana 44 with 3.92 to 5.89 ratio gear sets and 30 spline axle shafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40632 Empty Differential Case Kit For Dana Model 44 3.73 and numerically lower ratios. Includes ring gear bolts and diff shims
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40633 Loaded Differential Case Assembly For Dana Model 44 3.73 and numerically lower ratios. Includes spider gears, diff bearings, ring gear bolts and diff shims
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40634 Empty Differential Case Kit For Dana Model 44 3.92 and numerically higher ratios. Includes ring gear bolts and diff shims
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40635 Loaded Differential Case Assembly For Dana Model 44 3.92 and numerically higher ratios. Includes spider gears, diff bearings, ring gear bolts, and diff shims
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Makers

top_page
photo
TK40573 Torque King® 6 Bolt Front Hub Gasket For 1957-1966 Dodge W100 and 1957-1975 Dodge W200 Closed Knuckle Dana 44 Front Axles with 6 Bolt external mount lockout hubs is a brand new, precision cut, high-tech hub gasket
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU42028 Hipro Dana 44 Cover Gasket Is a reusaeable Dana 44 High Performance Differential Cover Gasket and genuine dana part for all Dana-Spicer Model 44 axles.
See our QU42028 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40214 Dana 44 Cover Gasket Is a genuine original equipment Dana Gasket for all Dana-Spicer Model 44 axles.
See our QU40214 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hubs and Hub Parts

top_page
photo

QU51181 Warn 20990 Premium Hub Set for Dana 44 Front Axles With internally splined front wheel hubs. Reliable and good looking. QU51181 Fits Dodge 1/2 ton Dana 44 1969-1971.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU56018 Warn Manual Hub Set Is a relable, original equipment quality hub set with installation hardware for all part time transfer case equipped 1969 to 1971 Dodge W100 1/2 tons with Dana 44 closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU56019 1Side Warn Manual Hub Set
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4918 Hub Service Kit For QU56018 Warn Manual Hub Set
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50818 Warn Premium Quality 6 Bolt External Mount Hub Set For 1957-1971 W200 3/4 Ton and 1957-1968 W100 1/2 ton 4x4s with Dana 44 front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40548 M31E Warn Lock-O-Matic Hub Set Looking for the ultimate Lock Out Hub set for your restored 1960's to mid 1970's 3/4 or 1 ton gem? Tough Warn Lock-O-Matic Hubs give you the option of automatic engagement/disengagement AND the ability to manually engage the hubs for compression braking and continuous 4 wheeling
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40598/QU40428/QU40657 Splined Front Hub Gears for Dana 44 Bolt Front Axles Were used on 4x4s without lockout hubs from 1959 to 1993. These one piece, solid steel splined hub gears provide the strongest connection between your axle shaft and wheel hub
photo
QU40614 Inverted Lug Outer Axle Shaft Snap Ring Is a genuine original equipment Dana part for 1970's to mid 1990's Dodge 4x4s with 19 Spline Outer Axle Shafts. One of these snap rings is used on each outer axle shaft
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40035 Hub Spring Plate Fits between the QU40050 hub spring and the outer wheel bearing cup on SUV's, and pickups with Dana Spicer Model 44 front drive axles equipped with internal mount, Spicer lock out hubs or full time drive gears
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40050 Spicer Tapered Hub Spring For SUV's, and pickups with Dana Spicer Model 44 front drive axles equipped with internal mount, Spicer lock out hubs or full time drive gears. These springs were used on most of the late 1960's to mid 1980's Dodge 4x4s with internal splined front wheel hubs. Made in U.S.A. LIMITED SUPPLY
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40427 Dana 44 Full Time Front End Hub Cap Is a genuine Dana replacement part for 1973-1993 Dodge 4x4 SUVs and trucks with Dana 44 front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts

top_page
photo
QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S24200 Blue Threadlocker For spindle and ring gear bolts etc
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S81343 Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding.
See our S81343 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90018 Pyroplex® Protection ES Synthetic Grease Provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90016 SynPower ® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90015 High Performance Synthetic Arctic Grease Is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90017 Red Grease Is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. cartridge or 1 pound tub
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT9404 Application Brush Is ideal for applying Gear Marking Compound or Anti-Seize Lubricant to parts. Brush fibers and steel handle are resistant to most automotive chemicals. Made in U.S.A.
See our QT9404 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals and Pinion Yokes

top_page
photo
QU40215 Dana Axle Pinion Seal Is a original equipment spec pinion double lip pinion yoke seal manufactured by the Dana supplier for this seal since the 1970's. Fits most 1940s to early 1990s Dana 25, Dana 27, Dana 30, or Dana 44 front or rear axles.
See our QU40215 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
QU40177 Genuine Dana 4.09 Ring and Pinion Kit With pinion bearings, pinion seal, and small parts for standard Dana 44 axles. Use with 26 spline pinion yoke
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40447 Genuine Dana 3.54 Ring and Pinion Kit With pinion bearings and small parts for Dana 44
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
QU42009 Original Equipment 7/16" ID Tapered Locking Bushing Cone for Dodge Dana 44 Front Steering Arms Fits the steering arms on 1957-1971 Dodge W100 and W200 standard Dana 44 closed knuckle front axles with a trapezoid steering arm to steering knuckle bolt pattern and a steering arm attached with 7/16" studs.

Link to our QU42009 Catalog Product Page

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindles and Spindle Nuts

top_page
product note

Dodge used both hex and round spindle nuts on standard Dana 44 closed knuckle front axles. W-100 1/2 ton trucks up through 1968 and all the W-200 3/4 ton models through 1971 will have 1-3/4" spindle threads, external mount hubs and use a 4 piece spindle nut set with 2 hex nuts, a flat inner spindle washer and a bend over tab lockwasher. 1969 to 1971 W-100 models with internal splined wheel hubs use a 3 piece round spindle nut set with 1-5/8" thread nuts with four slots.

photo
QU10576 Bend Over Tab Lock Washer for Dodge W-100, W-200 with Standard Dana 44 Front Axles Fits 1957-1968 Dodge W-100 and 1957-1971 Dodge W-200 4x4 trucks with hex spindle nuts and external mount wheel hubs. Washer has two pre-bent tabs that fit over the inner spindle nut and 6 bend-over tabs for the outer spindle nut. Sold individually
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU11164 1-3/4 Thread Spindle Hex Nut for Dodge W-100, W-200 with Standard Dana 44 Front Axles For 1957-1968 Dodge W-100 and 1957-1971 Dodge W-200 4x4 trucks with hex spindle nuts and external mount wheel hubs. Fits 1-3/4" Spindle Threads. Hex size is 2-1/2". Use 2 per side, 4 per vehicle. Sold individually.
Link to our QU11164 Catalog Product Page
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU11165 Spindle Thrust Washer for Dodge W-100, W-200 with Standard Dana 44 Front Axles For 1957-1968 Dodge W-100 and 1957-1971 Dodge W-200 4x4 trucks with hex spindle nuts and external mount wheel hubs. Fits 1-3/4" Spindle Threads. One of these washers is used on each side between the outer wheel bearing and inner spindle nut. Sold individually.
Link to our QU11165 Catalog Product Page
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40004 1969-1971 Dodge W-100 Dana 44 Front Inner Spindle Nut Threads on the spindle and fits against your outer wheel bearing to provide correct wheel bearing end-play. Sold individually
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40060 1969-1971 Dodge W-100 Dana 44 Front Spindle Lock Washer Locks your QU40004 Inner Spindle Nut in position when properly installed. Sold individually
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40031 1969-1971 Dodge W-100 Dana 44 Front Outer Spindle Nut Is tightened against your QU40060 Spindle Lock Washer to keep the it in place and it acts as a jam nut effectively locking both spindle nuts and the washer together. Sold individually
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4727 1969-1971 Dodge W-100 Dana 44 Front Spindle Nut Kit Includes one each of QU40004 Inner Spindle Nut, QU40060 Spindle Lock Washer, and QU40031 Outer Spindle Nut
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Bushings

top_page
product note

One of these Bushings are pressed into the inboard side of each spindle to support your outer axle shaft. These are one of the most common 1957-1971 Dodge Dana 44 closed knuckle front end parts requiring replacement as both the thrust face and inside diameter of the Bushing are subject to wear.

photo
QU40025 Spindle and Axle Shaft Bushing for 1957-1971 Dodge Dana 44 Closed Knuckle Axles Is a genuine original equipment flanged Bronze Bushing that gets pressed into the back of the spindle to support the axle shafts in your 1957-1971 Dodge W100 or W200 Power Wagon® 4x4 truck
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Knuckles

top_page
QU42009 Original Equipment 7/16" ID Tapered Locking Bushing Cone for Dodge Dana 44 Front Steering Arms Fits the steering arms on 1957-1971 Dodge W100 and W200 standard Dana 44 closed knuckle front axles with a trapezoid steering arm to steering knuckle bolt pattern and a steering arm attached with 7/16" studs.

Link to our QU42009 Catalog Product Page

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
photo
QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers.
See our QT1100 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1802 Outer Wheel Bearing Cup Installer To install outer wheel bearing cups on all 1969-1971 Dodge W100 closed knuckle and 1972-1974 Dodge W100 open knuckle front axles with drum brakes.
See our QT1802 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1803 Inner Wheel Bearing Cup Installer To install inner wheel bearing cups on all 1969-1971 Dodge W100 closed knuckle and 1972-1974 Dodge W100 open knuckle front axles with drum brakes.
See our QT1803 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1504 Front Wheel Seal Installer Is specifically made to install QU50654 inner wheel grease seals to the correct depth without damaging the seal.
See our QT1504 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1012 4 Lug 4x4 Front Spindle Nut Socket Fits 4 slot spindle nuts with Dana 44 Front Axles
See our QT1012 large text individual page for more details and tech notes
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1025 Universal 4 Lug/6Lug Front or Rear Spindle Nut Socket For Dana 44 Front Axles
See our QT1025 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT5500 Wheel Bearing Packer Takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your 4x4!
See our QT5500 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals (Individual)

top_page
photo
QU50704 1957-1968 W100 and W200 Front Wheel Seal For all 1957-1968 Dodge W100 and W-200 4x4 trucks with Dana 44 drum brake, closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU50702 1957-1968 W100 and W200 Timken® Inner or Outer Wheel Bearing QU50702 is used in both the inner and outer wheel bearing postions on all 1957-1968 Dodge W100 and W-200 4x4s with Dana 44 drum brake, closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU50701 1957-1968 W100 and W200 Timken® Inner or Outer Wheel Bearing Cup For all 1957-1968 Dodge W100 and W-200 4x4 trucks with Dana 44 drum brake, closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50654 1969-1971 W100 Front Wheel Seal For all 1969-1971 Dodge W-100 1/2 ton 4x4 trucks with Dana 44 drum brake, closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50577 1969-1971 W100 Timken® Inner Wheel Bearing Cup For all 1969-1971 Dodge W-100 1/2 ton 4x4 trucks with Dana 44 drum brake, closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50578 1969-1971 W100 Timken® Inner Wheel Bearing For all 1969-1971 Dodge W-100 1/2 ton 4x4 trucks with Dana 44 drum brake, closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50447 1969-1971 W100 Timken® Outer Wheel Bearing Cup For all 1969-1971 Dodge W-100 1/2 ton 4x4 trucks with Dana 44 drum brake, closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50448 1969-1971 W100 Timken® Outer Wheel Bearing For all 1969-1971 Dodge W-100 1/2 ton 4x4 trucks with Dana 44 drum brake, closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU50703 1969-1971 W200 Timken® Inner Wheel Bearing For all 1969-1971 W200 3/4 ton 4x4 trucks with Dana 44 drum brake, closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
product note

It is always good preventative maintenance to replace the all wheel bearings and seals when restoring or maintaining your vintage 4x4. The parts availability for decades old 4x4s declines on a daily basis. Wrecking a wheel hub and/or spindle when the old bearing you reused fails can either cost you a mint or put your broken-down truck on blocks forever. We stock Kits with high quality Timken® Wheel Bearings and North American made Wheel Seals to keep your veteran Dodge rolling.

TK4924 1957 to 1968 Dodge W100 and W200 Torque King® Wheel Bearing Kit for Dana 44 Front Axles Fit 1957 to 1968 Dodge W100 and W200 4x4 pickups with Dana 44 closed knuckle front axles. TK4924 Master Kit includes 4 Timken® Bearings with Bearing Cups, 2 Wheel Seals, 2 Spindle Nut Lock Washers, and 2 Hub Gaskets
photo
TK4911/TK4912 1969 to 1971 Dodge W100 1/2 ton Torque King® Wheel Bearing Kits for Dana 44 Front Axles Fit 1969 to 1971 Dodge W100 4x4 pickups. TK4911 Master Kit includes 4 Timken® Bearings with Bearing Cups, 2 Wheel Seals, Bearing Cup Installers, Wheel Seal Installer and Driver Handle. TK4912 Parts Only Kit includes the same great parts but no tools
TK4926 1969 to 1971 Dodge W200 Torque King® Wheel Bearing and Seal Kit for Dana 44 Front Axles Fit 1969 to 1971 Dodge W200 4x4 pickups with Dana 44 closed knuckle front axles. TK4926 Kit includes 4 Timken® Bearings with Bearing Cups, 2 Wheel Seals, 2 Spindle Nut Lock Washers, and 2 Hub Gaskets