Front Constant Velocity Driveshaft Parts for 2008-up Dodge Ram 4500 and Ram 5500 4x4 Trucks

We stock a complete line of Double Cardan front CV driveshaft parts for 2003  and newer Dodge Ram 2500, 3500, 4500 and Dodge Ram 5500 4x4 trucks. These Dodge 4x4s use a Double-Cardan Constant Velocity (CV) Joint at the transfer case end, and a conventional single Carden universal joint with a flange yoke and axle end for the Front Driveshaft's. While the basic configuration of the shafts is the same for all years, the actual components used will vary depending upon the year and engine/transmission combination.

Dan the Gear Man® Tech Note: The Tech Term "Cardan" refers to a conventional cross type universal joint. A Double-Cardan CV joint is a constant velocity joint that has two Cardan type universal joints as component parts. For more information on this subject, see TSB3500 Universal Joint History, Types, General Service Methods, and Inspection or TM3000 Driveshaft Service Manual.

Driveshaft Assemblies

top_page

QU11370 Complete New Front Constant Velocity Drive Shaft for 2008-2018 Dodge Ram 4500, Ram 5500 with Cummins Diesel and G56 6 Speed Manual Transmission. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU11371 Complete New Front Constant Velocity Drive Shaft for 2008-2018 Ram 4500, Ram 5500 with Cummins Diesel & Aisin Automatic Transmission. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Boots

top_page
photo

QU11120 Front Driveshaft Slip Yoke Boot and Clamp Kit for 2008-up Dodge Ram 4500, Ram 5500 4x4 trucks.
More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Constant Velocity Parts

top_page
product note

We stock a complete line of original equipment quality replacement parts for rebuilding your Dodge Ram 4500 or Ram 5500 Front Double-Cardan Constant Velocity (CV) Joint. The front CV shafts used on the Ram 4500 and Ram 5500 are NOT interchangeable with those used in Ram 2500 or Ram 3500 models although some of the components are.

tech note

Dan the Gear Man® Tech Note: The 1/2" diameter Centering Stud on your Ball Stud Tube Yoke (QU40864 ) MUST be in good condition to successfully rebuild your CV joint (See TSB3503, TM3000, or TM3318 ). If there is visible grooving or if the stud is worn more than 0.002"-.003" you will need to replace your Ball Stud Tube Yoke. While not difficult for a skilled machinist, this will require lathe work, welding, and straightening of the shaft. It is also strongly recommended you have the shaft rebalanced after assembly

photo
QU40800 Dodge Ram 4500, Ram 5500 CV Center Yoke For 2008-2012 Dodge Ram 4500, Ram 5500 4x4 front drive Constant Velocity shafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40803 Dodge Ram 4500, Ram 5500 CV Flange Yoke Assembly for 2008-2012 Dodge Ram 4500, Ram 5500 4x4 front drive Constant Velocity shafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40704 Dodge Ram 4500, Ram 5500 Press On Dust Seal for Double-Cardan Constant Velocity Joint for 2008-up Ram 4500, Ram 5500. This seal helps protect the CV Ball and should be replaced any time the u-joints are changed
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40744 Dodge Ram 4500, Ram 5500 CV Ball Replacement Kit For 2003-current Ram 4500, Ram 5500 4x4 front driveshafts. If your CV Flange casting is OK, you can save money by replacing just the worn ball and seat with this part. Be advised you will need a 1"-1¼" blind hole bearing puller and a hydraulic press. Includes Ball-Needle/Bearings-Seat and spring
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40864 Dodge Ram 4500, Ram 5500 Greaseable Ball Stud Tub Yoke For 2008-2012 Dodge Ram 4500 and 5500 4x4 front constant-Velocity Driveshafts that have a Cup Diameter of 1-3/16". Includes QU40704 Dust Seal. The recessed lube fitting permits regular greasing of the Constant Velocity Ball
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40829 Dodge Ram 4500, Ram 5500 Replacement CV Grease Seal For 2008-2012 Dodge Ram 4500 and Ram 5500 4x4 front constant-Velocity Driveshaft's Double-Cardan CV Joint. This part is included in QU40744 Ball Kit and is part of QU40131 and QU40803 CV Flanges
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40835 Dodge Ram 4500, Ram 5500 Replacement CV Tension Spring For 2008-2012 Dodge Ram 4500 and Ram 5500 4x4 front constant-Velocity Driveshaft's Double-Cardan CV Joint. This part is included in QU40744 Ball Kit and with QU40131 and QU40803 CV Flanges
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Rebuild Kits

top_page

QK3114 Front Driveshaft Rebuild Kit with CV Flange Yoke and 3 Greaseable Universal Joints for 2010-2013 ALL and 2007-2009 Dodge Ram 4500, Ram 5500 with all 3 front u-joints having 1-3/16" cups. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!