Parts for 1972-1979 Dana-Spicer Model 60 Rear Axles in Dodge Trucks

The 1970's was a time of transition for Dodge pickups. Besides the obvious body style change in 1972, rear axle options became more standardized making parts identification a bit simpler, but you still must know the brake size or axle capacity of your axle to order parts prior to disassembly. We stock many of the common parts for these axles and perhaps a few of the less common, but our stock of major components is pretty much used up.

Axle Shafts and Axle Shaft Hardware

top_page
photo

QU42108U Used 30 Spline Rear Axle Shaft for 1971-1982 Dana 60 Rear Axles. Axle shaft holes are tapered. More Info

$70.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40535 Rear Axle Shaft to Wheel Hub Bolt for 1976-1979 Dana 60 Full Float Rear Axles using bolts for axle shaft retention. Sold Individually. More Info

$2.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42009 Original Equipment 7/16" ID Tapered Locking Bushing Cone fits 1990 and earlier Dana 60 and Dana 60HD rear axle shafts with tapered holes in the drive flange as found in many older Dodge trucks. Limited to stock on hand. More Info Also, QU42009U Used Tapered Locking Bushing Cone Limited to stock on hand.

$17.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40577 Tapered Locking Bushing Cone for Dana 60 and Dana 60HD Rear Axle Shafts fits factory axle shafts retained by 7/16" studs for 1972-1979 Dodge Dana 60 and Dana 60HD rear axles in 3/4 ton trucks. QU40577 is an aftermarket replacement split taper axle shaft cone that was redesigned to address the Cone becoming frozen in the tapered axle shaft holes. For trucks built after April 1, 1976, this part will be primarily found on 6200 pound capacity Dana 60HD rear axles. More Info

$6.71
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
photo

QU11116 1972-1979 Brake Block Bolt/Axle Vent Fitting Is a genuine original equipment hollow bolt that is used to attach the rear brake junction block to the axle housing and it acts as the axle vent outlet to which you attach the axle vent hose to your 1972 to 1979 Dodge Dana 60 rear axle. More Info

$10.30
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Case

top_page
photo

QU42120U Used 16 Spline Dana 60 Loaded Open Differential Case for 4.10 and faster gear ratio Dana 60 axles in 1975 and older trucks.

More Info

$150.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings, Individual

top_page
product note

Over the years, Dana has primarily used Timken bearings when building their axles. For long life and dimensional consistency, Timken bearings are unmatched by any other brand of bearing I have used rebuilding axles over the past 30+ years in the business. When you are a shade tree mechanic dealing with a diff and pinion rebearing job without all the fancy gauging tools we have, you always want your new bearings to be the same overall thickness as the original bearings were when the axle was built so your pinion depth, pinion preload and backlash are within the tolerance limits when you are done with the job. Timken bearings will almost always deliver that type of accuracy, plus the steel quality and surface finish is the world's best.

photo

QU50397 Differential Bearing Cup For Dana Model 60 Rear Axles in 1972-1979 Dodge D-200/250 and W-200/250 3/4 ton trucks. More Info

$20.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50398 Differential Bearing For Dana Model 60 Rear Axles in 1972-1979 Dodge D-200/250 and W-200/250 3/4 ton trucks. More Info

$19.28
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50400 Outer Pinion Bearing Cup For Dana Model 60 Rear Axles in 1972-1979 Dodge D-200/250 and W-200/250 3/4 ton trucks. More Info

$10.88
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50401 Outer Pinion Bearing For Dana Model 60 Rear Axles in 1972-1979 Dodge D-200/250 and W-200/250 3/4 ton trucks. More Info

$22.71
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50406 Inner Pinion Bearing Cup For Dana Model 60 Rear Axles in 1972-1979 Dodge D-200/250 and W-200/250 3/4 ton trucks. More Info

$20.92
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50407 Inner Pinion Bearing For Dana Model 60 Rear Axles in 1972-1979 Dodge D-200/250 and W-200/250 3/4 ton trucks. More Info

$35.12
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing and Seal Kits

top_page
photo

QU50491 Differential Bearing & Seal Kit for Dana Model 60 Rear Axles in 1972-1979 Dodge D-200/250 and W-200/250 3/4 ton trucks. This kit includes: QU50400 Outer Pinion Bearing Cup, QU50401 Outer Pinion Bearing, QU50406 Inner Pinion Bearing Cup, QU50407 Inner Pinion Bearing, 2 QU50397 Differential Bearing Cups, 2 QU50398 Differential Bearings; QU51065 early and QU50565 late, aftermarket pinion seal; QU50566 aftermarket pinion nut, QU50567 aftermarket differential and pinion shim kit; and QU90009 axle service pack. More Info

$189.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
product note

Differential problems with Dana 60 rear axles are not all that common. But Murphy, of Murphy's Law* really likes busted differentials, so when you hear that loud, heart-stopping, ominous BANG from the rear axle as your truck lurches to a grinding stop, you just KNOW it is one big dose of bad news. To help get you back on the road after you get rescued, we stock genuine original equipment Dana-Spicer Front Axle Differential Parts for your hard working Dodge truck.
*Murphy's Law: "Anything that can go wrong, will go wrong"

photo

QU40518 Differential Pinion Mate Thrust Washer for Open Differentials Two of these Thrust Washers are used in each differential, one between each pinion mate gear and the differential case. More Info

$2.20
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40041 Differential Side Gear Thrust Washer for Open Differentials Two of these Thrust Washers are used in each differential, one between each side gear and the differential case. More Info

$3.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40520 Differential Cross Shaft for Open Differentials More Info

$15.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40519 Lock Pin for Differential Cross Shaft for Open Differentials Is used to lock QU40520 differential cross shaft to the diff case. More Info

$2.89
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets

top_page
product note

In the mid 1970's Dana made a differential cover design change to heavy gauge covers with flat mating flanges. Unlike the previous, thin gauge covers with embossed flanges which were made for use with a cut gasket, the new design, thick gauge covers are designed for sealing with RTV. If you desire, you can still use a gasket with the new type cover by combining the gasket with thin films of RTV. We stock both Ultra Gray RTV Sealant and genuine Dana Gaskets.

photo

QU40367 Rear Differential Cover Gasket For Model 70 Axles. These genuine Dana-Spicer gaskets will also work on Dana 60 axles. Dan the Gear Man Tech Note: RTV sealant instead of Gaskets were used during the factory assembly of your axle. More Info

$9.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40078 Rear Axle shaft Flange Gasket To prevent oil leaks, your Axle Shaft Flange Gaskets should be replaced anytime the axle is removed. These embossed steel gaskets are genuine Dana-Spicer parts. More Info

$6.26
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. More Info

$8.85
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals

top_page
product note

Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations.

photo

TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles.

More Info

$20.95
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts & Lubricants

top_page
product note

Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings.

photo

S24200 Blue Threadlocker For spindle and ring gear bolts etc. More Info

$6.91
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern. More Info

$3.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding. More Info

$1.62
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90018 Pyroplex® Protection ES Synthetic Grease Provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions! More Info

$9.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90016 SynPower® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints. More Info

$9.58
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90015 Syncon High Performance Synthetic Arctic Grease Is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather. More Info

$8.44
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90017 707L Red Grease Is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. 1 pound tub. More Info

$7.33
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40218 4 Ounce Limited Slip Lube Is supplied by Dana-Spicer for all Powr-Lok and Trac-Lok limited-slip differentials in 1982-1979 Dodge D200, W200, D250, and W250 trucks with Dana 60 Rear Axles. For a professional job, we recommend one 4 ounce bottle of lube to soak your clutches and one 4 ounce bottle to add to your rear differential oil after any drain and refill of axle lubricant. More Info

$12.75
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound. More Info

$6.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Yokes and Seals

top_page
product note

Dodge used a number of different Pinion Yokes for 1972-1979 Dana 60 Rear Axles. Replacement recommendations for the various u-joint sizes are:
Detroit 7260 1.078" cups, 2-1/8" inside lock-up: QU10087U Yoke or QK4878 Conversion Yoke Kit
Detroit 7290: 1.125" cups, 2-5/8" inside lock-up: QU40747 Yoke
Detroit 5380: 1.232" cups, 3" inside lock-up: QK4650 Yoke Kit + special order QU40898 Conversion Joint

photo

QU40097 Dana 70 Pinion Seal For 1972-1979 Dodge D200, D250, W200, and W250 trucks with Dana 60 Rear Axles. More Info

$11.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40747 7290 Series 29 Spline Dana 70 Pinion Yoke for Dodge Ram Rear Axles Genuine original equipment yoke fits those 1972 to 1979 Dodge Vans and pickups with Dana 60 Rear Axles and Detroit 7290 series inside C-Clip retained universal joints that have 1.125" diameter cups. Inside dimension between Yoke Ears is 2-5/8". More Info

$189.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11074 7290 Series Pinion Yoke (No Slinger) for some 1978-1979 Dodge Vans and pickups with Dana 60 Rear Axles and Detroit 7290 series inside C-Clip retained universal joints that have 1-1/8" diameter cups. Inside dimension between yoke ears measures 2-5/8". More Info

$99.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40763 7290 U-Joint Strap and Bolt Kit For 1972-1979 Dodge trucks and vans with 7290 series rear driveshaft u-joints. Special small head, hardened bolts for attaching the driveshaft to the front axle pinion yoke. 7290 series u-joints have internal C-Clips, 1-1/8" diameter cups and fit yokes measuring 2-5/8" between the ears. More Info

$14.90
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11087U Used 29 Spline 7260 Series Pinion Yoke for Dodge Dana 70 Rear Axles For 1972-1979 Dodge trucks with Dana 60 axles and Detroit 7260 series inside C-Clip retained universal joints that have 1.078" diameter cups. Inside dimension between Yoke Ears is 2-1/8". More Info

$0.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4878 1310 Series x 7260 Series Conversion Pinion Yoke Kit for Dodge Dana 60 Axles Includes a strong, solid cross special conversion u-joint that allows to to replace your damaged original Dodge Pinion Yoke made for 7260 series u-joints with a new pinion yoke that accepts a Spicer series u-joint. Just install the new parts and bolt your old driveshaft to the new pinion yoke! More Info

$114.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40729 7260 U-Joint Strap and Bolt Kit With special small head, hardened bolts for attaching the driveshaft to your rear axle pinion yoke. This Strap and Bolt Kit is used to secure Dodge (Detroit Universal) 7260 series universal joints with 1.078" diameter cups to axle pinion yokes with an inside yoke width of 2-1/8". More Info

$7.15
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
photo

QU42009 OE Tapered Locking Bushing Cone for Dana 60 and Dana 60HD Rear Axle Shafts fits factory axle shafts retained by 7/16" studs for 1972-1979 Dodge Dana 60 and Dana 60HD rear axles in 3/4 ton trucks. QU42009 is an original equipment split taper axle shaft cone. For trucks built after April 1, 1976, this part will be primarily found on 6200 pound capacity Dana 60HD rear axles. More Info. Also available QU42009U Used Original Equipment Tapered Lock Wedge Limited to stock on hand.

$17.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40577 Tapered Locking Bushing Cone for Dana 60 and Dana 60HD Rear Axle Shafts fits factory axle shafts retained by 7/16" studs for 1972-1979 Dodge Dana 60 and Dana 60HD rear axles in 3/4 ton trucks. QU40577 is an aftermarket replacement split taper axle shaft cone that was redesigned to address the Cone becoming frozen in the tapered axle shaft holes. For trucks built after April 1, 1976, this part will be primarily found on 6200 pound capacity Dana 60HD rear axles. More Info

$6.71
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Nuts and Spindle Nut Hardware

top_page
product note

Dodge used 5500 pound rated Dana 60 and 6200 pound capacity Dana 60HD rear axles in 1972-1979 D200 4x2 , and W200 4x4 3/4 ton trucks, plus for the 1979 model year, a 6200 pound capacity Dana 60HD was also offered as the base D300 4x2 1 ton rear axle. During the 1972-1979 model years, Dodge made a number of engineering changes on Dana 60 series rear axles, including different wheel bearings for the 5500 pound Dana 60.  In addition to the product listings below, we have 2 pages of Application Charts showing all the spindle nuts, rear wheel bearing and hub parts for 1972-1979 era Dodge Dana 60 and Dana 60HD full floating rear axles:
Application Charts 1 & 2 1972-1979 D200, W200, D300 Dana 60/60HD Rear Spindle Nut Applications
Application Charts 3 & 4 1972-1979 B300, P200, P300, and Motorhome 60/60HD Rear Spindle Nut Applications

photo

QK4763 2-3/8" Hex Spindle Nut Kit for 1972, 1973, 1974, 1975, 1976 200 and 300 series Dodge trucks with Dana 60 full float rear axles having 1-13/16" diameter spindle threads. See Application Charts above. More Info

$32.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40027 Rear Dana 60 Bend Over Tab Spindle Nut Lockwasher For 1972 to 1976 200 and 300 series Dodge trucks with Dana 60 full float rear axles having 1-13/16" diameter spindle threads. See Application Charts above. More Info

$6.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40026 Rear Dana 60 2-3/8" Hex Spindle Nut For 1972 to 1976 200 and 300 series Dodge trucks with Dana 60 full float rear axles having 1-13/16" diameter spindle threads. See Application Charts above. More Info

$14.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4730 Hex Spindle Nut Kit for 1972 to 1979 (up to 1/8/79) 200 and 300 series Dana 60HD full float rear axles and 1977 to 1979 (up to 1/8/79) 200 and 300 series Dana 60 full float rear axles having 2" diameter spindle threads. See Application Charts above. More Info

$29.67
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40052 2-1/2" Hex Rear Spindle Hub Nut for 2" thread. This is a replacement Nut for the original QU11070 2-9/16" Hex Nut in 1972 to 1979 (up to 1/8/79) 200 and 300 series Dana 60HD full float rear axles and 1977 to 1979 (up to 1/8/79) 200 and 300 series Dana 60 full float rear axles having 2" diameter spindle threads. See Application Charts above. More Info

$13.92
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40051 Bend Over Tab Spindle Lock Washer with wide Key Tab fits 2" diameter spindles in 1972 to 1979 (up to 1/8/79) 200 and 300 series Dana 60HD full float rear axles and 1977 to 1979 (up to 1/8/79) 200 and 300 series Dana 60 full float rear axles having 2" diameter spindle threads. See Application Charts above. More Info

$6.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4015 Spindle Nut Kit for 1979 (after 1/8/79) 200 and 300 series Dodge trucks with Dana 60 and Dana 60HD full float rear axles. See Application Charts above. More Info

$86.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40077 Spindle Nut Is a "Single Use Only" Elastic Stop Type Spindle Lock Nut for 1979 (after 1/8/79) 200 and 300 series Dodge trucks with Dana 60 and Dana 60HD full float rear axles. See Application Charts above. More Info

$34.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40089 Spindle Nut Lock Wedge Is a "Single Use Only" replacement Lock Wedge that is designed to prevent QU40077 Spindle Nut from backing off. Fits 1979 (after 1/8/79) 200 and 300 series Dodge trucks with Dana 60 and Dana 60HD full float rear axles. See Application Charts above. More Info

$4.76
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

In addition to the product listings below, we have 2 pages of Application Charts showing all the rear wheel bearing and seal tool applications for 1972-1979 era Dodge Dana 60 and Dana 60HD full floating rear axles:
Application Charts 1 & 2 1972-1979 D200, W200, D300 Dana 60/60HD Rear Wheel Bearing and Seal Tool Applications
Application Charts 3 & 4 1972-1979 B300, P200, P300, and Motorhome 60/60HD Rear Wheel Bearing and Seal Tool Applications

photo

QT1226i 2-3/8" 6 Point Hex Socket with 1/2" Drive. See Application Charts above. More Info

$19.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1013i 2-1/2" Hex Spindle Nut Socket is a 1/2" drive thin-wall socket made to fit front or rear Dana Spicer drive axles with 2" spindle threads and that have hex spindle nuts measuring 2-1/2" across the flats. See Application Charts above. USA made QT1013 available. More Info

$19.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1218 2-9/16" Hex Spindle Nut Socket fits the 2-9/16" (measured across the flats) stock front or rear hex spindle nuts on many Dodge 3/4 ton and one-ton trucks with Chrysler or Dana full float axles from the 1940's to 1991. Heavy Duty 3/4" drive. See Application Charts above. More Info

$33.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1009i 2-9/16" Rounded Hex Spindle Nut Socket is a 1/2" Drive, thinwall socket specifically made to fit the special rounded rear spindle nuts used on some Dana Spicer full float rear axles with 2" spindle threads in Dodge 3/4 ton and 1-ton models. NOT FOR IMPACT USE! See Application Charts above. USA made QT1009 available. More Info

$19.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1511 Rear Wheel Seal Installer installs QU50892 Wheel Seal in 1972-1976 D200, W200, B300, P200, CB300 Dana 60 Rear Axle with Single Rear Wheels. Use with a QT1100 series Installer Handle. See Application Charts above. More Info

$29.95
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1500 Dodge Dana 60HD Rear Wheel Seal Installer is specifically made to install QU40450 seals and similar inner wheel seals in 1993 and earlier Dodge 3/4 ton and 1-ton trucks with Dana 60HD rear axles and single rear wheels. Most of these trucks have a tin outer shield around the back of the wheel hub that is supposed to channel oil from a leaking seal away from the brake shoes. QT1500 is made to pass through the inside diameter of the shield which is only slightly larger than the outside diameter of the seal. Installing a wheel seal without damaging it in these older Dodge trucks is very difficult without the use of this Installer. A relief groove in the installer allows adequate clearance for the outer seal lip, thereby preventing one of the most common causes of premature seal failure. Use with a QT1100 series Installer Handle. See Application Charts above. More Info

$32.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1502 Rear Wheel Seal Installer for Dodge is specifically made to install QU90001 and similar flanged rear inner wheel seals in Dana 60 Rear axles in 1977 to 1979 Dodge 3/4 ton models. The Installer is made to clear the raised outer shell on all popular wheel seals for these vehicles. A relief groove in the installer allows adequate clearance for the outer seal lip, thereby preventing one of the most common causes of premature seal failure. Use with a QT1100 series Installer Handle. See Application Charts above. More Info

$26.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1512 Dodge Dana 60HD or 70 Dual Rear Wheel Seal Installer is specifically made to install QU40451 and similar inner wheel seals in 1993 and earlier Dodge 1 ton trucks with Dana 70 rear axles and dual rear wheels. Also fits 1972-1979 Dana 60HD B300, CB300, MB300, M300, R300, P300 with Dual Rear Wheels. Most of these trucks have a tin outer shield around the back of the wheel hub that is supposed to channel oil from a leaking seal away from the brake shoes. QT1512 is made to pass through the inside diameter of the shield which is only slightly larger than the outside diameter of the seal. Installing a wheel seal without damaging it in these older Dodge trucks is very difficult without the use of this Installer. A relief groove in the installer allows adequate clearance for the outer seal lip, thereby preventing one of the most common causes of premature seal failure. Use with a QT1100 series Installer Handle. See Application Charts above. More Info

$32.95
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1805 Inner Wheel and Pinion Bearing Cup Installer is used to install QU50406 inner pinion bearing cups and QU50568 inner wheel bearing cups used in 1972-1976 D200, W200, B300, P200, CB300 Single Rear Wheel Dana 60 Rear Axles. Precision CNC machined solid steel tool is drilled to accept any driver handle with a 5/8" tip. See Application Charts above. More Info

$22.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1814 Outer Wheel Bearing Cup Installer is for setting QU50658 outer wheel bearing cups in 1972-1976 D200, W200, B300, P200, CB300 Single Rear Wheel Dana 60 Rear Axles. Precision CNC machined solid steel tool is drilled to accept any driver handle with a 5/8" tip. See Application Charts above. More Info

$22.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1804 Inner Wheel Bearing Cup Installer for installing QU50414 Timken Inner Wheel Bearing Cups in 1972-1979 (up to 1/8/79 build date) D200, W200, D300 and 1979 (after 1/8/79 build date) D200, D300, with Dana 60HD and Single Rear Wheels. Also fits 1974-1979 B300 Dana 60HD and Singe Rear Wheels. Precision CNC machined solid steel tool is drilled to accept any driver handle with a 5/8" tip. See Application Charts above. More Info

$26.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1801 Inner & Outer Wheel Bearing Cup Installer is used to install QU50411 Wheel Bearing Cups used in 1977-1979 D200, W200 Dana 60 Single Rear Wheels, 1972-1979 (up to 1/8/79 build date) D200, W200, D300 Dana 60HD with Single Rear Wheels, 1979 D200, D300 Dana 60HD with Single Rear Wheels. Also used in 1972-1979 B300, CB300, MB300, M300, R300, P300, P200 for various year applications. See Application Charts above for specific applications. Precision CNC machined solid steel tool is drilled to accept any driver handle with a 5/8" tip. More Info

 

$23.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1806 Inner Wheel Bearing Cup Installer for installing QU50377 Bearing Cups in 1972-1979 B300, CB300, MB300, M300, R300, P300 Dana 60HD with Dual Rear Wheels. Precision CNC machined solid steel tool is drilled to accept any driver handle with a 5/8" tip. See Application Charts 3 & 4 above. More Info

$29.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals, Individual

top_page
product note

Dodge used 5500 pound rated Dana 60 and 6200 pound capacity Dana 60HD rear axles in 1972-1979 D200 4x2 , and W200 4x4 3/4 ton trucks, plus for the 1979 model year, a 6200 pound capacity Dana 60HD was also offered as the base D300 4x2 1 ton rear axle. During the 1972-1979 model years, Dodge made a number of engineering changes on Dana 60 series rear axles, including different wheel bearings for the 5500 pound Dana 60. In addition to the product listings below, we have 2 pages of Application Charts showing all the rear wheel bearing and hub parts for 1972-1979 era Dodge Dana 60 and Dana 60HD full floating rear axles:
Application Charts 1 & 2 1972-1979 D200, W200, D300 Dana 60/60HD Rear Wheel Hub and Bearing Applications
Application Charts 3 & 4 1972-1979 B300, P200, P300, and Motorhome 60/60HD Rear Wheel Hub and Bearing Applications

Section 1
Rear Wheel Bearings and Seals for 1972-1976 5500 Pound Rated SINGLE REAR WHEEL Dana 60 Rear Axles for Dodge Trucks, Vans, and Motorhomes. Spindle Thread Size is 1-13/16"

photo

QU50658 1972-1976 Timken® Outer Rear Wheel Bearing Cup For 1972-1976 5500 pound rated, single rear wheel Dodge Dana 60 rear axles in D200 and W200 trucks plus P200, P300, B300 vans and van based Motorhome chassis. Spindle thread size is 1-13/16". More Info

$21.12
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50659 1972-1976 Timken® Outer Rear Wheel Bearing For 1972-1976 5500 pound rated, single rear wheel Dodge Dana 60 rear axles in D200 and W200 trucks plus P200, P300, B300 vans and van based Motorhome chassis. Spindle thread size is 1-13/16". More Info

$56.91
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50568 1972-1976 Timken® Inner Rear Wheel Bearing Cup For 1972-1976 5500 pound rated, single rear wheel Dodge Dana 60 rear axles in D200 and W200 trucks plus P200, P300, B300 vans and van based Motorhome chassis. Spindle thread size is 1-13/16". More Info

$16.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU50891 1972-1976 Timken® Inner Rear Wheel Bearing For 1972-1976 5500 pound rated, single rear wheel Dodge Dana 60 rear axles in D200 and W200 trucks plus P200, P300, B300 vans and van based Motorhome chassis. Spindle thread size is 1-13/16". More Info

$50.57
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50892 Inner Wheel Seal For 1972-1976 5500 pound rated, single rear wheel Dodge Dana 60 rear axles in D200 and W200 trucks plus P200, P300, B300 vans and van based motorhome chassis. Spindle thread size is 1-13/16". More Info

$22.26
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

SECTION 2
REAR WHEEL BEARINGS AND SEALS FOR 1977-1979 5500 POUND RATED SINGLE REAR WHEEL DANA 60 REAR AXLES FOR DODGE TRUCKS, VANS, AND MOTORHOMES. SPINDLE THREAD SIZE IS 2" and INNER/OUTER BEARINGS ARE SAME NUMBERS

photo

QU50411 1977-1979 5500 Pound Rated Dodge Dana 60 Inner or Outer Timken Wheel Bearing Cup for 1977-1979 D200, W200 3/4 Ton Dodge Truck, 1979 D300 1 ton or 1977-1979 GVW B300 1 ton van with standard Dana 60 full floating rear axle and Single Rear Wheels. Bearing cup OD is 3-1/4". Requires 2 Bearing Cups per wheel. More Info

$8.15
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50412 1977-1979 5500 Pound Rated Dodge Dana 60 Inner or Outer Timken Wheel Bearing for 1977-1979 D200, W200 3/4 Ton Dodge Truck, 1979 D300 1 ton or 1977-1979 GVW B300 1 ton van with standard Dana 60 full floating rear axle and Single Rear Wheels. Spindle Thread Size is 2". Requires 2 Bearings per wheel. More Info

$14.46
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90001 1977-1979 5500 Pound Rated Dodge Dana 60 Inner or Outer Timken Wheel Seal for 1977-1979 D200, W200 3/4 Ton Dodge Truck, 1979 D300 1 ton or 1977-1979 GVW B300 1 ton van with standard Dana 60 full floating rear axle and Single Rear Wheels. More Info

$8.27
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

SECTION 3
REAR WHEEL BEARINGS AND SEALS FOR 1972-1979 5800 or 6200 POUND RATED SINGLE REAR WHEEL DANA 60HD REAR AXLES FOR DODGE TRUCKS and 9,000 Pound GVW VANS. SPINDLE THREAD SIZE IS 2"

photo

QU50411 Outer Timken Wheel Bearing Cup for 1972-1979 6200 pound capacity SRW Dana 60HD fits 1972-1979 D200, 1974-1976 W200, and 1979 D300 plus 1974-1979 9,000 pound GVW B300 1 ton van with 6200 pound rated Dana 60HD  full floating rear axle and Single Rear Wheels. More Info

$8.15
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50412 Outer Timken Wheel Bearing for 1972-1979 6200 pound capacity SRW Dana 60HD fits 1972-1979 D200, 1974-1976 W200, and 1979 D300 plus 1974-1979 9,000 pound GVW B300 1 ton van with 6200 pound rated Dana 60HD  full floating rear axle and Single Rear Wheels. More Info

$14.46
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50413 SRW Timken® Inner Bearing Cup For 1972 to 1979 Dodge 3/4 ton and 1 ton trucks with single rear wheels, Dana 60HD rear axles (D200HD, D300, W300) and 12" x 3" rear brakes. More Info

$18.66
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50414 SRW Timken® Inner Wheel Bearing For 1972 to 1979 Dodge 3/4 ton and 1 ton trucks with single rear wheels, Dana 60HD rear axles (D200HD, D300, W300) and 12" x 3" rear brakes. More Info

$31.55
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40450 Single Rear Wheel Seal for 1972 to 1979 Dodge 3/4 ton and 1 ton trucks with single rear wheels and Dana 60HD rear axles (D200HD, D300, W300) and 12" x 3" rear brakes. Conventional (no seating flange) Double lip seal features Wave seal inner lip to contain oil and protective outer wiper lip to exclude brake dust and other contaminants. More Info

$15.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

SECTION 4
REAR WHEEL BEARINGS AND SEALS FOR 1972-1979 6200 POUND RATED DUAL REAR WHEEL DANA 60HD REAR AXLES FOR VANS and MOTORHOMES. SPINDLE THREAD SIZE IS 2"

photo

QU50411 Outer Timken Wheel Bearing Cup for 1972-1979 6200 pound capacity DRW Dana 60HD fits 1972-1979 Dodge Vans and Class 3 Motorhomes with 6200 pound rated Dana 60HD  full floating rear axle and Dual Rear Wheels. More Info

$8.15
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50412 Outer Timken Wheel Bearing for 1972-1979 6200 pound capacity DRW Dana 60HD fits 1972-1979 Dodge Vans and Class 3 Motorhomes with 6200 pound rated Dana 60HD  full floating rear axle and Dual Rear Wheels. More Info

$14.46
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50377 DRW Timken® Inner Wheel Bearing Cup For 1972 to 1979 Dodge motor homes, B300, D300, W300, 1 ton trucks with Dana 60HD rear axles, 12"x3" brakes, and dual rear wheels. More Info

$19.21
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50376 DRW Timken® Inner Wheel Bearing For 1972 to 1979 Dodge motor homes, B300, D300, W300, 1 ton trucks with Dana 60HD rear axles, 12"x3" brakes, and dual rear wheels. More Info

$46.52
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40451 Original Equipment Dual Rear Wheel Seal for 1972 to 1979 Dodge motor homes, B300, D300, W300, 1 ton trucks with Dana 60HD rear axles, 12"x3" brakes, and dual rear wheels. More Info

$20.92
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50075 Special Double Lip Dual Rear Rear Wheel Seal features outer wiper lip to protect the inner lip from brake and road crud. Fits 1972 to 1979 Dodge motor homes, B300, D300, W300, 1 ton trucks with Dana 60HD rear axles, 12"x3" brakes, and dual rear wheels. More Info

$32.46
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
product note

Until the end of the 1976 model year, Dodge Single Rear Wheel Dana 60 rear axles with up to 12" x 2-1/2" brakes had 1-13/16" ID outer wheel bearings. Effective with the 1977 model year, Dodge Dana 60 rear axles in standard D200/D250/W200/W250 trucks and standard B300/B350 vans with up to 12" x 2-1/2" rear brakes came with identical 2"ID inner and outer rear wheel bearings. Dodge did also use a number of different single and dual rear wheel Dana 60HD configurations with 12 x3 brakes that use different inner/outer bearings depending upon if the axle has single or dual rear wheels.

In addition to the product listings below, we have 2 pages of Application Charts showing all the rear wheel bearing and hub parts for 1972-1979 era Dodge Dana 60 and Dana 60HD full floating rear axles:
Application Charts 1 & 2 1972-1979 D200, W200, D300 Dana 60/60HD Rear Wheel Hub and Bearing Applications
Application Charts 3 & 4 1972-1979 B300, P200, P300, and Motorhome 60/60HD Rear Wheel Hub and Bearing Applications

photo

TK8304 SRW Torque King® Master Rear Wheel Bearing and Seal Kit with Installation Tools for 1972-1979 D200, W200, and D300 Dana 60HD Single Rear Wheel Full Float Rear Axles and 1974-1979 B300 Dana 60HD Single Rear Wheel Full Float Rear Axles. TK8304 features premium Timken® bearings and original equipment quality wheel seals because when it comes to rear wheel bearings and seals, only the best will do to safely support the heavy loads your truck hauls. See Application Charts above. More Info

$259.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK8321 Torque King® Rear Wheel Bearing and Seal Kit for 1972 to 1979 D200, W200, and D300 Dana 60HD Single Rear Wheel Full Float Rear Axles features premium Timken® bearings and original equipment quality wheel seals because when it comes to rear wheel bearings and seals, only the best will do to safely support the heavy loads your truck hauls. See Application Charts above. More Info

$174.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4891 Torque King® Rear Wheel Bearing Only Kit for 1972 to 1979 D200, W200, and D300 Dana 60HD Single Rear Wheel Full Float Rear Axles. Features premium Timken® Bearing and Cups. See Application Charts above. More Info

$142.36
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK8303 1977-1979 Torque King® Master Rear Wheel Bearing & Seal Kit with Tools For 1977-1979 D250, W250 3/4 Ton Dodge Trucks or 1977-1979 Dodge B300/B350 Vans with standard Dana 60 rear axle and Single Rear Wheels. Kit includes Seal and Bearing Cup Installation Tools, Timken® Wheel Bearings, Original Equipment Wheel Seals, Axle Shaft Flange Gaskets, and Threadlocker. See Application Charts above. More Info

$169.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK8320 1977-1979 Parts Only Torque King® Premium Rear Wheel Bearing & Seal Kit for 1977-1979 Dodge D250 and W250 3/4 Ton Dodge Trucks or 1977-1979 Dodge B300/B350 Vans with standard Dana 60 rear axle and Single Rear Wheels. Kit includes Timken® Wheel Bearings, Original Equipment Wheel Seals, Axle Shaft Flange Gaskets, and Threadlocker. See Application Charts above. More Info

$106.95
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4915 Torque King® Rear Wheel Bearing Only Kit for 1977 to 1979 Dodge D250 and W250 3/4 Ton trucks and 1977 to 1979 B300 and B350 Vans with standard Dana 60 rear axles and Single Rear Wheels. Timken® Wheel Bearings and Timken® Wheel Bearing Cups. See Application Charts above. More Info

$82.33
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK8305 Torque King® Master Rear Wheel Bearing and Seal Kit with Installation Tools for 1972-1979 Dodge Dana 60HD Dual Rear Wheel Axles features premium Timken® bearings and original equipment quality wheel seals because when it comes to rear wheel bearings and seals, only the best will do to safely support the heavy loads your truck hauls. This Kit fits Vans and van based chassis with Dana 60HD dual rear wheel rear axles. See Application Charts above. More Info

$339.65
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK8322 DRW Torque King® Rear Wheel Bearing and Seal Kit for 1972-1979 Dodge Dana Dana 60HD Dual Rear Wheel Axles features premium Timken® bearings and original equipment quality wheel seals because when it comes to rear wheel bearings and seals, only the best will do to safely support the heavy loads your truck hauls. This Kit fits Vans and van based chassis with either Dana 60HD dual rear wheel rear axles. See Application Charts above. More Info

$223.65
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4892 Torque King® Rear Wheel Bearing Only Kit for 1972-1979 Dodge Dana 60HD Dual Rear Wheel Axles features premium Timken® bearings because when it comes to rear wheel bearings, only the best will do to safely support the heavy loads your truck hauls. Kit includes Inner and outer wheel bearings/bearing cups. This Kit fits 1972 to 1979 Dodge Vans and van based chassis with Dana 60HD dual rear wheel rear axles that have 2" Spindle Threads. See Application Charts above. More Info

$161.13
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Hubs

top_page
product note

Dodge used different, non-interchangeable wheel hubs for Dana 60 rear axles. Axles rated under 6200 pounds use hubs with identical inner and outer wheel bearings. Hubs for 6200 pound and higher single rear wheel applications have a larger inner wheel bearing. The hub used for dual rear wheel axles.

photo

QU11288U Used 1972-1979 Dodge Dana 60HD and Dana 70 Single Rear Wheel Hub fits Dodge 3/4 and 1 ton Single Rear Wheel (SRW) trucks with Dana full-floating rear axles with 6200 pound or higher axle weight ratings. Over the years, Dodge used this hub with Dana 60, Dana 60HD, and Dana 70 rear axles in both trucks and 1 ton vans. Limited to stock on hand. More Info

$150.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!