Parts for 1980-1993 Dana-Spicer Model 60 Rear Axles in Dodge Trucks

During the 1980-1993 period, the Dana 60 rear axle used in Dodge pickups was pretty much standardized on most components except the wheel bearings. One significant change was the introduction of rear anti-lock brakes for the 1989 model year

Axle Shafts and Axle Shaft Small Parts

top_page
photo

TK40588 Dana 60 30 Spline Torque King Rear Axle Shaft for 1980-1992 gas engine Dodge 250.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42108U Used 30 Spline Rear Axle Shaft for 1980-1982 Dana 60 Rear Axles. Also fits 1989-1990 Single Rear Wheel D200HD and D300HD Single Rear Wheel and Camper Special Trucks. Axle shaft holes are tapered.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42009 Original Equipment 7/16" ID Tapered Locking Bushing Cone fits 1990 and earlier Dana 60 rear axle shafts with tapered holes in the drive flange as found in many older Dodge trucks. Limited Supply.
More Info
Also, QU42009U Used Tapered Locking Bushing Cone while supply lasts.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40577 Tapered Locking Bushing Cone for Dana 60 Rear Axle Shafts fits the factory axle shafts for 1980-1993 6200 pound capacity Dodge Dana 60 rear axles in 3/4 ton trucks. QU40577 is an aftermarket replacement split taper axle shaft cone that was redesigned to address the Cone becoming frozen in the tapered axle shaft holes.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
photo
QU11116 1980-1993 Brake Block Bolt/Axle Vent Fitting Is a genuine original equipment hollow bolt that is used to attach the rear brake junction block to the axle housing and it acts as the axle vent outlet to which you attach the axle vent hose to your 1980 to 1993 Dodge Dana 60 rear axle.
Link to our QU11116 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings, Individual

top_page
product note
Over the years, Dana has primarily used Timken bearings when building their axles. For long life and dimensional consistency, Timken bearings are unmatched by any other brand of bearing I have used rebuilding axles over the past 30+ years in the business. When you are a shade tree mechanic dealing with a diff and pinion rebearing job without all the fancy gauging tools we have, you always want your new bearings to be the same overall thickness as the original bearings were when the axle was built so your pinion depth, pinion preload and backlash are within the tolerance limits when you are done with the job. Timken bearings will almost always deliver that type of accuracy, plus the steel quality and surface finish is the world's best
photo
QU50397 Differential Bearing Cup For Dana Model 60 Axles in 1980-1993 Dodge D-250 3/4 ton trucks.
Link to our QU50397 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50398 Differential Bearing For Dana Model 60 Rear Axles in 1980-1993 Dodge D-250 3/4 ton trucks.
Link to our QU50398 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50400 Outer Pinion Bearing Cup For Dana Model 60 Rear Axles in 1980-1993 Dodge D-250 3/4 ton trucks.
Link to our QU50400 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50401 Outer Pinion Bearing For Dana Model 60 Rear Axles in 1980-1993 Dodge D-250 3/4 ton trucks.
Link to our QU50401 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50406 Inner Pinion Bearing Cup For Dana Model 60 Rear Axles in 1980-1993 Dodge D-250 3/4 ton trucks.
Link to our QU50406 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50407 Inner Pinion Bearing For Dana Model 60 Rear Axles in 1980-1993 Dodge D-250 3/4 ton trucks.
Link to our QU50407 Large Text Catalog Page for more detail & tech info
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearing Kits

top_page
photo
QU50491 Differential Bearing & Seal Kit for Dana Model 60 Rear Axles in 1980-1993 Dodge D-250 3/4 ton trucks. This kit includes: QU50400 Outer Pinion Bearing Cup, QU50401 Outer Pinion Bearing, QU50406 Inner Pinion Bearing Cup, QU50407 Inner Pinion Bearing, 2 QU50397 Differential Bearing Cups, 2 QU50398 Differential Bearings; QU51065 early and QU50565 late, aftermarket pinion seal; QU50566 aftermarket pinion nut, QU50567 aftermarket differential and pinion shim kit; and QU90009 axle service pack. Contains USA and imported parts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
product note
Differential problems with Dana 60 rear axles are not all that common. But Murphy, of Murphy's Law* really likes busted differentials, so when you hear that loud, heart-stopping, ominous BANG from the rear axle as your Dodge lurches to a grinding stop, you just KNOW it is one big dose of bad news. To help get you back on the road after you get rescued, we stock genuine original equipment Dana-Spicer Front Axle Differential Parts for your hard working 3/4 ton Dodge W-250 or 1 ton W-350 truck.
*Murphy's Law: "Anything that can go wrong, will go wrong"
photo
QU40518 Differential Pinion Mate Thrust Washer for Open Differentials Two of these Thrust Washers are used in each differential, one between each pinion mate gear and the differential case.
Link to our QU40518 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40041 Differential Side Gear Thrust Washer for Open Differentials Two of these Thrust Washers are used in each differential, one between each side gear and the differential case.
Link to our QU40041 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40520 Differential Cross Shaft for Open Differentials Link to our QU40520 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40519 Lock Pin for Differential Cross Shaft for Open Differentials is used to lock QU40520 differential cross shaft to the diff case.
Link to our QU40519 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU11096 Dana 60 Basic Differential Shim Kit Is a basic selection of aftermarket differential adjusting shims that fit between the differential bearing and differential case to adjust for gear backlash and differential bearing preload.
Link to our QU11096 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets

top_page
product note
In the mid 1970's Dana made a differential cover design change to heavy gauge covers with flat mating flanges. Unlike the previous, thin gauge covers with embossed flanges which were made for use with a cut gasket, the new design, thick gauge covers are designed for sealing with RTV. If you desire, you can still use a gasket with the new type cover by combining the gasket with thin films of RTV. We stock both Ultra Gray RTV Sealant and genuine Dana Gaskets
photo
QU40367 Rear Differential Cover Gasket For Model 70 Axles. These genuine Dana-Spicer gaskets will also work on Dana 60 axles. Dan the Gear Man Tech Note: RTV sealant instead of Gaskets were used during the factory assembly of your axle.
Link to our QU40367 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40078 Rear Axle shaft Flange Gasket To prevent oil leaks, your Axle Shaft Flange Gaskets should be replaced anytime the axle is removed. These embossed steel gaskets are genuine Dana-Spicer parts.
Link to our QU40078 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Dodge Dana 60.
Link to our S82194 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals

top_page
photo
TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous

top_page
product note
Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings
photo
S24200 Blue Threadlocker For spindle and ring gear bolts, etc.
Link to our S24200 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90018 Pyroplex® Protection ES Synthetic Grease Provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions!
Link to our QU90018 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90016 SynPower ® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90015 Syncon High Performance Synthetic Arctic Grease Is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90017 Red Grease Is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. cartridge or 1 pound tub
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40218 4 Ounce Limited Slip Lube Is supplied by Dana-Spicer for all Powr-Lok and Trac-Lok limited-slip differentials in 1980-1993 Dodge D250 and W250 trucks with Dana 60 Rear Axles. For a professional job, we recommend one 4 ounce bottle of lube to soak your clutches and one 4 ounce bottle to add to your rear differential oil after any drain and refill of axle lubricant.
Link to our Large Individual QU40218 Page
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound.
Link to our QU90009 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Yokes and Pinion Seals

top_page
photo
QU40097 Dana 60 Pinion Seal For 1980-1993 Dodge D250 and W250 trucks with Dana 60 Rear Axles.
Link to our QU40097 Large Text Catalog Page for more detail & tech info
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40747 7290 Series 29 Spline Dana 60 Pinion Yoke for Dodge Ram Rear Axles Genuine original equipment yoke fits those 1980 to 1993 Dodge Vans and pickups with Dana 60 Rear Axles and Detroit 7290 series inside C-Clip retained universal joints that have 1.125" diameter cups. Inside dimension between Yoke Ears is 2-5/8".
Also see QU11074
Please refer to QU40747 page for more details and ordering information.
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40763 7290 U-Joint Strap and Bolt Kit for 1980-1993 Dodge trucks and vans with 7290 series rear driveshaft u-joints. Special small head, hardened bolts for attaching the driveshaft to the front axle pinion yoke. 7290 series u-joints have internal C-Clips, 1-1/8" diameter cups and fit yokes measuring 2-5/8" between the ears.
Link to our QU40763 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU11087U Used 29 Spline 7260 Series Pinion Yoke for Dodge Dana 60 Rear Axles For 1980-1993 Dodge trucks with Dana 60 axles and Detroit 7260 series inside C-Clip retained universal joints that have 1.078" diameter cups. Inside dimension between Yoke Ears is 2-1/8".
Link to our QU11087U Large Text Catalog Page for more detail & tech info
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4878 1310 Series x 7260 Series Conversion Pinion Yoke Kit for Dodge Dana 60 Axles Includes a strong, solid cross special conversion u-joint that allows to to replace your damaged original Dodge Pinion Yoke made for 7260 series u-joints with a new pinion yoke that accepts a Spicer series u-joint. Just install the new parts and bolt your old driveshaft to the new pinion yoke!
Link to our QK4878 Large Text Catalog Page for more detail & tech info
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40729 7260 U-Joint Strap and Bolt Kit With special small head, hardened bolts for attaching the driveshaft to your rear axle pinion yoke. This Strap and Bolt Kit is used to secure Dodge(Detroit Universal) 7260 series universal joints with 1.078" diameter cups to axle pinion yokes with an inside yoke width of 2-1/8".
Link to our QU40729 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
photo
QU11116 Breather Bolt for 1990-1993 Dodge Rear Axles Link to our QU11116 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU11096 Dana 60 Basic Differential Shim Kit Is a basic selection of aftermarket differential adjusting shims that fit between the differential bearing and differential case to adjust for gear backlash and differential bearing preload.
Link to our QU11096 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40577 Tapered Locking Bushing Cone for Dana 60 Rear Axle Shafts fits the factory axle shafts for 1980-1993 6200 pound capacity Dodge Dana 60 rear axles in 3/4 ton trucks. QU40577 is an aftermarket replacement split taper axle shaft cone that was redesigned to address the Cone becoming frozen in the tapered axle shaft holes. Also available while supplies last: QU42009 Original Equipment Split Taper Locking Bushing Link to QU40577 Large Text Individual Product Page
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Nuts and Spindle Nut Hardware

top_page
tech note

Dan the Gear Man® Tech Note: QU40077 Spindle Nuts and QU40089 Spindle Lock Wedges are "Single Use", genuine Dodge and Dana Spicer original equipment components. These parts are designed to be installed once and only once. For safety reasons, you must discard both the nut and wedge if they are removed from the spindle for any reason. Both parts lose a percentage of their resistance to coming off when they are removed. You may hear of cases where this type of factory nut has come off while the truck was being driven. Invariably, these failures involve nuts and wedges that have been reused. I am not aware of a single instance of a properly installed new nut and wedge coming off like that. In my opinion, the original equipment nut design is as safe to use as our double nut sets sold above as long as you follow the rules

photo

TK4000 Torque King® Double Spindle Nut Upgrade Kit with Socket For 1979-1993 Dodge D-250, W-250 trucks with Dana-Spicer Model 60 full float rear axles.
More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4001 Torque King® Double Spindle Nut Upgrade Kit For 1979-1993 Dodge D-250, W-250 trucks with Dana-Spicer Model 60 full float rear axles.
More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4014 Torque King® Double Spindle Nut Upgrade Spare Parts Kit For 1979-1993 Dodge D-250, W-250 trucks with Dana-Spicer Model 60 full float rear axles.
More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40036 Torque King® 6 slot replacement Spindle Nut For TK4000, TK4001 Upgrade Kits.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40037 Torque King® bend-over tab Spindle Lockwasher For TK4000, TK4001 Upgrade Kits.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4013 Stock Spindle Nut Kit with Socket For 1979-1993 Dodge D-250, D-250 trucks with Dana-Spicer Model 60 rear axles.
More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4015 Stock Spindle Nut Kit For 1979-1993 Dodge D-250, W-250 trucks with Dana-Spicer Model 60 rear axles.
More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40077 Locking Rear Spindle Nut for Model 60 Rear Axles Is a genuine original equipment, single use, replacement stock spindle nut for all 1980 to 1993 Dodge D-200, D-250, W-200, and W-250 trucks with Dana-Spicer Model 60 rear axles. Use with QU40089.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40089 Spindle Nut Lock Wedge for Model 60 Rear Axles Is a genuine original equipment, single use, replacement Lock Wedge that is designed to prevent QU40077 Spindle Nut from backing off. Use with QU40077.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
photo
QT1009 Spindle Nut Socket For QU40077 standard spindle nuts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1009i Rounded Hex Spindle Nut Socket for QU40077 Standard Spindle Nut
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1025 Spindle Nut Socket For QU40036 spindle nuts used in the TK4000, TK4001 Torque King® Rear Double Spindle Nut Upgrade Kits

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1100 8" Standard Duty Installer Driver Handle For general purpose use with knurled hand grip

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1101 14" Standard Duty Installer Driver Handle For general purpose use with knurled hand grip for deep seated bearing cups such as inner pinion

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1116 8" Professional Duty Installer Driver Handle A beefier version of our standard handle for the professional technician with knurled hand grip

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1119 14" Professional Duty Installer Driver Handle A beefier version of our standard handle for the professional technician with knurled hand grip

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1502 Wheel Seal Installer

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1801 Wheel Bearing Cup Installer
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals, Individual

top_page
product note
Dodge matches the wheel bearings and seals used with an axle to the original rear brake size. For 1980-1993 Dodge Dana 60 rear axles in gas engine D250/W250 trucks and standard B350 vans, the original rear brake size is almost always either 12" x 2" or 12" x 2-1/2". These axles use QU50411/QU50412 for both inner and outer bearings. Dodge did also use a number of different single and dual rear wheel Dana 60HD configurations with 12"x 3" or 12" x 3-1/2" rear brakes with different inner/outer bearings in special purpose trucks, vans and motor homes
photo
QU50411 Inner or Outer Timken Wheel Bearing Cup for 1980-1993 D250/W250 3/4 Ton Dodge Truck and 1980-1993 B350 Vans with Dana 60 rear axles, 12"x 2" or 12" x 2-1/2" brakes, and Single Rear Wheels. Bearing cup OD is 3-1/4". Requires 2 Bearing Cups per wheel
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50412 Inner or Outer Timken Wheel Bearing for 1980-1993 D250/W250 3/4 Ton Dodge Truck and 1980-1993 B350 Vans withDana 60 rear axles, 12"x 2" or 12" x 2-1/2" brakes, and Single Rear Wheels.Bearing ID is 2". Requires 2 Bearings per wheel
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90001 Flanged Rear Wheel Seal for 1980-1993 D250/W250 3/4 Ton Dodge Truck and 1980-1993 B350 Vans withDana 60 rear axles, 12"x 2" or 12" x 2-1/2" brakes, and Single Rear Wheels.

Link to our QU90001 Catalog Page
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40450 Single Rear Wheel Seal for 1980 to 1993 Dodge 3/4 ton and 1 ton vehicles with single rear wheels and Dana 60HD rear axles (D250HD, D350, W350) and 12" x 3" rear brakes. Conventional (no seating flange) Double lip seal features Wave seal inner lip to contain oil and protective outer wiper lip to exclude brake dust and other contaminants
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40451 Original Equipment Dual Rear Wheel Seal for 1980 to 1993 Dodge motor homes, B300, D350, W350, 1 ton trucks with Dana 60HD rear axles, 12"x3" or 12" x 3-1/2" brakes, and dual rear wheels
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50075 Special Double Lip Dual Rear Rear Wheel Seal features outer wiper lip to protect the inner lip from brake and road crud. Fits 1980 to 1993 Dodge motor homes, B300, D350, W350, 1 ton trucks with Dana 60HD rear axles, 12"x3" or 12x3-1/2" brakes, and dual rear wheels
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50413 SRW Timken® Inner Bearing Cup For 1980 to 1993 Dodge 3/4 ton and 1 ton vehicles with single rear wheels and Dana 60HD rear axles (D250HD, D350, W350) and 12" x 3" rear brakes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50414 SRW Timken® Inner Wheel Bearing For 1980 to 1993 Dodge 3/4 ton and 1 ton vehicles with single rear wheels and Dana 60HD rear axles (D250HD, D350, W350) and 12" x 3" rear brakes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50377 DRW Timken® Inner Wheel Bearing Cup For 1980 to 1993 Dodge motor homes, B300, D350, W350, 1 ton trucks with Dana 60HD rear axles, 12"x3" or 12x3-1/2" brakes, and dual rear wheels
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50376 DRW Timken® Inner Wheel Bearing For 1980 to 1993 Dodge motor homes, B300, D350, W350, 1 ton trucks with Dana 60HD rear axles, 12"x3" or 12x3-1/2" brakes, and dual rear wheels
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
product note
The rear wheel bearings in 1980-1993 Dodge Dana 60 Rear axles average about 125, 000 to 150, 000 miles before requiring replacement. Torque King® Premium Rear Wheel Bearing and Seal Kits for your Dodge feature premium Timken® bearings and original equipment quality wheel seals because when it comes to rear wheel bearings and seals, only the best will do to safely support the heavy loads your truck hauls. To help you install these vital components properly, Torque King® Master Kits include bearing cup and wheel seal installers. Why use makeshift installation methods that can damage precision surfaces when affordable tools are available to do the job right the first time?
photo
TK8303 Torque King® Master Rear Wheel Bearing & Seal Kit with Tools For 1980-1993 D250, W250 3/4 Ton Dodge Trucks or 1980-1993 Dodge B350 Vans with standard Dana 60 and Single Rear Wheels. Kit includes Seal and Bearing Cup Installation Tools, Timken® Wheel Bearings, Original Equipment Wheel Seals, Axle Shaft Flange Gaskets, and Threadlocker.
Link to our TK8303 Catalog Page
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK8320 Parts Only Torque King® Premium Rear Wheel Bearing & Seal Kit for 1980-1993 Dodge D250 and W250 3/4 Ton Dodge Trucks or 1980-1993 Dodge B350 Vans with standard Dana 60 and Single Rear Wheels. Kit includes Timken® Wheel Bearings, Original Equipment Wheel Seals, Axle Shaft Flange Gaskets, and Threadlocker.
Link to our TK8320 Catalog Page
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Hubs

top_page
photo

QU11288U Used 1980-1993 Dodge Dana Dana 60HD and Dana 70 Single Rear Wheel Hub fits Dodge 3/4 and 1 ton Single Rear Wheel (SRW) trucks with Dana full-floating rear axles with 6200-pound or higher axle weight ratings. Over the years, Dodge used this hub with Dana 60, Dana 60HD, and Dana 70 rear axles in both trucks and 1-ton vans.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!