Closed Knuckle Dana-Spicer Model 70 Front Axle Parts for 1958-1978 Dodge 4x4 Trucks

We stock a good selection of axle parts for the Dodge Power Wagon® W200, W300, and W600 Dana 70 Closed Knuckle 4x4 Front Axle. Dodge first used the 4500 pound rated, closed knuckle, Dana-Spicer Model 70 front axle in the 1958 "light civilian" W300. The new W series Power Wagons® were sold concurrently with the military inspired WM300 3/4 ton 4x4. Dodge used the 4500 pound Dana 70 for all W-300 Power Wagons® and some specially equipped W200 Power Wagons® from 1958-1974. The closed knuckle Dana 70 with drum brakes was replaced by a 4500 pound rated, disc brake, open knuckle Dana 60 for the 1975 model year. It is quite possible a few early 1975 model year Dodge W200/W300 were built with the closed knuckle Dana 70, but 1974 is the last year Dodge lists the 4500 pound Dana 70 in Dodge Parts Books.

The short lived 2 ton W-600 medium duty chassis cab truck replaced the W500 1-1/2 ton 4x4 in 1972. Like the W-500, the W-600, at first used the Rockwell FDS750 front axle when it was introduced, but for 1974, two axles were offered depending upon the chassis Gross Vehicle Weight (GVW). The 6000 pound rated, closed knuckle Dana 70 was the "light" axle and the heavy axle was a Rockwell 7500 pound rated FDS75.

The Dana 70 equipped W-600 was only built from 1974 to 1977 when Dodge ceased making medium duty trucks. The last few W-600s made were sold as 1978 models.

 

Axle Identification

top_page
photo

Not all Dana axles have the model number cast on the housing. It can be very difficult to tell a Dana 60 from a Dana 70, as they have nearly identical covers with exactly the same bolt pattern. One way to tell if you have a Dana 60 or Dana 70 is to measure the cover flange height (yellow arrow). The Dana 60 flange height is approximately 1" high. The Dana 70 flange height is about 1¼" high.

Axle Shaft Bushings, Axle Shaft Seals, and Axle Shaft Universal Joints

top_page
photo
QU40382 Inner Axle Shaft Oil Seal Is a genuine original equipment Dana combination oil seal and axle shaft guide for all 1958 to 1978 Dodge Dana 70 closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40431 Large Spindle and Axle Shaft Bushing for 1958-1978 Dodge Power Wagon® Dana Spicer 70 Closed Knuckle Front Axles Is a flanged Bronze Bushing used in both the spindle and axle housing tubes to support the front axle shafts in 1958-1978 Dodge Power Wagons®
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU11241U Used Right Tracta Type Dana 70 Front Axle Shaft Assembly For 1969-1974 Dodge W200 Heavy Duty and W300 4x4 trucks with Dana 70 closed knuckle front axles. Inner shaft has 35 splines, outer shaft has 21 splines. Factory listed over all length is listed as approximately 29 1/8". Actual installed length appears to be slightly longer, however the length does vary depending upon air gaps between the four parts
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU11242U Used Left Tracta Type Dana 70 Front Axle Shaft Assembly For 1969-1974 Dodge W200 Heavy Duty and W300 4x4 trucks with Dana 70 closed knuckle front axles. Inner shaft has 35 splines, outer shaft has 21 splines. Factory listed over all length is listed as approximately 46-5/8". Actual installed length appears to be about 1/8" shorter. however the length does vary depending upon air gaps between the four parts
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40898 Detroit 5680 series x 1410 Spicer series Conversion U-Joint for many 1967-1989 Dodge 1 Tons. Greaseable Spicer 1410 Series by Detroit Universal 5380 Series Conversion U-Joint for coupling Spicer 1410 series yokes to vintage Dodge truck 5380 series drive shafts
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40736 Greaseable 7260 to 1310 Conversion U-Joint for Special Applications QU40736 Greaseable 7260 to 1310 Conversion U-Joint for Special Applications is used to adapt a yoke made for a Spicer type, 3-7/32" wide external snap ring u-joint to an original pinion yoke made for a Dodge Detroit Universal 7260 series u-joint with 2-1/8"internal lockup.
Link to our QU40736 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shafts

top_page

TK42047 Torque King® Forged Chrome-Moly Right 35 Spline Inner Axle Shaft for 1969-1974 Dodge 4x4 1 Ton trucks with Dana 70 Closed Knuckle front axles.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK42048 Torque King® Forged Chrome-Moly Left 35 Spline Inner Axle Shaft for 1969-1974 Dodge 4x4 1 ton trucks with Dana 70 Closed Knuckle front axles.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK42092 Torque King® 23 Spline Dana 70 Right Inner Axle Shaft for 1958-1968 Dodge W300 4x4 1 ton trucks. USA Made thru-hardened replacement.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK42093 Torque King® 23 Spline Dana 70 Left Inner Axle Shaft for 1958-1968 Dodge W300 4x4 1 ton trucks. USA Made thru-hardened replacement.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Closed Knuckle Parts

top_page
product note

We stock the regular service closed knuckle parts for your 1958-1978 Dodge Power Wagon® 4x4 with a closed knuckle Dana 70 front axle which will have 12 bolt Knuckle Ball Hemisphere Seals. With a Closed Knuckle axle, the axle universal joints and king pin bearings are lubricated by very heavy oil or a viscous grease that will flow when the axle shafts rotate. A large multi-piece seal is bolted to the backside of the steering knuckle to keep lubricant in and water out. On poorly maintained closed knuckle axles or axles equipped with lockout hubs that are rarely used in 4x4, the upper king pin bearing and axle universal joint can suffer from lack of lubrication. The Ball Seals will usually weep some lubricant especially when standard gear oils are used as a lubricant. Submersion of the axle under water or condensation from temperature changes can cause moisture to build up inside the enclosed ball and lead to corrosion damage and part failures.

photo

QA4936 Replacement 12 Bolt Knuckle Ball Seal Kit for Dana Spicer Front Axles is for heavy duty Dana closed knuckle front axles in 1958-1978 Dodge W300 and W600 4x4 trucks with Dan Spicer Model 70 closed knuckle front drive axles. Kits include split metal backed ball seal, felt wiper seal, metal backing plates and 12 new serrated, flange head cap screws. Two kits required to service both sides of your front axle assembly. NOTE: QA4936 replaces QU40189.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4765 1958-1978 Dodge Power Wagon® Dana 70 Closed Knuckle Preload Shim Kit For Dana 70 closed knuckle front axles in 1958-1978 Dodge Power Wagons®
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4616 1958-1978 Dodge Power Wagon® Dana 70 Large Closed Knuckle Bearing and Bushing Kit Includes two upper Knuckle Bushings. two Knuckle Bearings, four Knuckle Bearing Cups, and Preload Shims for Dana 70 closed knuckle front axles in 1958-1978 Dodge Power Wagons®
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4618 1958-1978 Dodge Power Wagon® Dana 70 Large Closed Knuckle Bearing Kit Is a cheaper alternative to QK4616 kit. QK4618 includes four Knuckle Bearings, four Knuckle Bearing Cups, and Preload Shims for Dana 70 closed knuckle front axles in 1958-1978 Dodge Power Wagons®
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50600 1958-1978 Dodge Power Wagon® Dana 70 Timken® Knuckle Bearing For Dana 70 closed knuckle front axles in 1958-1978 Dodge Power Wagons®
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50601 1958-1978 Dodge Power Wagon® Dana 70 Timken® Knuckle Bearing Cup For Dana 70 closed knuckle front axles in 1958-1978 Dodge Power Wagons®
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40327 1958-1978 Dodge Power Wagon® Dana 70 Upper King Pin/Knuckle Bushing For Dana 70 closed knuckle front axles in 1958-1978 Dodge Power Wagons®
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40543 1958-1978 Dodge Power Wagon® Dana 70 Upper King Pin Key For Dana 70 closed knuckle front axles in 1958-1978 Dodge Power Wagons®
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK50785 Torque® King Timken® Large Closed Knuckle King Pin Bearing Kit For Dodge Dana 70
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU11272U Used Right Steering Knuckle for 1958-1974 Dodge W300 4x4 Trucks and heavy-duty W200 models with a Dana 70 closed knuckle front axle. Our good used QU11272U steering knuckles will fit the right side (passenger) of all Dodge Dana 70 closed knuckle front axles on W200 and W300 4x4s. Bare knuckle only, does not include the bolt on bearing caps.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU11273U Used Left Steering Knuckle for 1958-1974 Dodge W300 4x4 Trucks and heavy-duty W200 models with a Dana 70 closed knuckle front axle. Our good used QU11273U steering knuckles will fit the left side (drivers) of all Dodge Dana 70 closed knuckle front axles on W200 and W300 4x4s. Bare knuckle only, does not include the bolt on steering arm or bearing cap.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU42080U Used Lower King Pin Cap for 1958-1974 Dodge W300 4x4 Trucks and heavy-duty W200 models with a Dana 70 closed knuckle front axle.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU42083U Used Right Upper King Pin Cap for 1958-1974 Dodge W300 4x4 Trucks and heavy-duty W200 models with a Dana 70 closed knuckle front axle. King Pin has Key Slot for QU40543 Bushing Key

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU11274U Used Left Upper King Pin Cap and Steering Arm for 1972-1974 Dodge W300 4x4 Trucks and heavy-duty W200 models with a Dana 70 closed knuckle front axle. King Pin has Key Slot for QU40543 Bushing Key. Drag Link goes under steering arm.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings

top_page
product note

Over the years, Dana has primarily used Timken bearings when building their axles. For long life and dimensional consistency, Timken bearings are unmatched by any other brand of bearing I have used rebuilding axles over the past 30+ years in the business. When you are a shade tree mechanic dealing with a diff and pinion rebearing job without all the fancy gauging tools we have, you always want your new bearings to be the same overall thickness as the original bearings were when the axle was built so your pinion depth, pinion preload and backlash are within the tolerance limits when you are done with the job. Timken bearings will almost always deliver that type of accuracy, plus the steel quality and surface finish is the world's best.

photo
QU50400 Timken® Outer Pinion Bearing Cup For Dodge Dana 70 closed knuckle front axles in 1958-1974 W300, and 1974-1978 W600 4x4 trucks. Also fits those 1972-1974 W200 trucks with the optional, 4500 pound rated, heavy-duty Dana 70 closed knuckle front axle.

Please refer to QU50400 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50401 Timken® Outer Pinion Bearing For Dodge Dana 70 closed knuckle front axles in 1958-1974 W300, and 1974-1978 W600 4x4 trucks. Also fits those 1972-1974 W200 trucks with the optional, 4500 pound rated, heavy-duty Dana 70 closed knuckle front axle.

Please refer to QU50401 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50409 Timken® Inner Pinion Bearing Cup For Dodge Dana 70 closed knuckle front axles in 1958-1974 W300, and 1974-1978 W600 4x4 trucks. Also fits those 1972-1974 W200 trucks with the optional, 4500 pound rated, heavy-duty Dana 70 closed knuckle front axle.

Please refer to QU50409 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50602 Timken® Inner Pinion Bearing For Dodge Dana 70 closed knuckle front axles in 1958-1974 W300, and 1974-1978 W600 4x4 trucks. Also fits those 1972-1974 W200 trucks with the optional, 4500 pound rated, heavy-duty Dana 70 closed knuckle front axle.

Please refer to QU50602 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50397 Timken® Dana 70 Differential Bearing Cup For Dodge Dana 70 closed knuckle front axles in 1958-1974 W300, and 1974-1978 W600 4x4 trucks. Also fits those 1972-1974 W200 trucks with the optional, 4500 pound rated, heavy-duty Dana 70 closed knuckle front axle.

Please refer to QU50397 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50398 Timken® Dana 70 Differential Bearing For Dodge Dana 70 closed knuckle front axles in 1958-1974 W300, and 1974-1978 W600 4x4 trucks. Also fits those 1972-1974 W200 trucks with the optional, 4500 pound rated, heavy-duty Dana 70 closed knuckle front axle.

Please refer to QU50398 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals

top_page
product note

Dan the Gear Man® Product Note: Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations.

photo

TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous

top_page
product note

Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings.

QU56024 21 Spline Lock Out Hub Set For 1968-1974 Dodge Dana 70 Closed Knuckle Front Axles are built to order in the U.S.A. with all new parts and feature a large dial that is easy to turn even when wearing gloves. Spring-Lock design permits hub engagement even if the axles shafts are not perfectly aligned. No more fighting to engage the second hub!

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU11240U Used Front Brake Drum For 1972-1974 Trucks with Single Rear Wheels fit the 12" x 3" brakes on 1972-1974 W200 and W300 4x4 trucks with single rear wheels and Dana 70 Closed Knuckle Front Axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S24200 Blue Threadlocker For spindle and ring gear bolts etc
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S9975 Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90018 Pyroplex® Protection ES Synthetic Grease provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90016 Is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90015 High Performance Synthetic Arctic Grease Is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90017 Red Grease Is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. cartridge or 1 pound tub
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40218 4 Ounce Limited Slip Lube Is supplied by Dana-Spicer for all Powr-Lok and Trac-Lok limited-slip differentials in 1980-1993 Dodge D250 and W250 trucks with Dana 60 Rear Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40367 Dodge Dana 70 Front Differential Cover Gasket Genuine Dana gasket is precisian cut specifically for the Model 70 series axles. High grade, crush resistant gasket material with clean die cuts and no hanging chads.

Also available: QU42030 Dana High Performance Reuseable Dana 70 Diff Cover Gasket
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Yokes

top_page
product note

Most Dodge Dana 70 front axles were built with beefy Detroit Universal 5380 series yokes. You will also find dinky Detroit Universal 7260 yokes on later production W200 axles. The Detroit Universal yokes are out of production and no longer available as new parts, however, you can change to Spicer series yokes by using conversion u-joints.

photo
QK4878 1310 Series x 7260 Series Conversion Pinion Yoke Kit for 1972-1974 Dodge W200 Dana 70 Axles Includes a greaseable special conversion u-joint that allows to to replace your damaged original 1972-1974 7260 series Dodge Pinion Yoke made for 7260 series u-joints with a new pinion yoke that accepts a conversion series u-joint. Just install the new parts and bolt your old driveshaft to the new pinion yoke!
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4650 Dana 70 Rear Pinion Yoke Kit For converting 1967-1978 Dodge Dana Model 70 Closed Knuckle Front Axles to use Spicer 1410 Series U-Joints. Also order QU40898 Detroit 5680 series x 1410 Spicer series Conversion U-Joint to attach QU40727 29 spline 1410 yoke to your 5380 series front driveshaft. QK4650 Kit includes (1) QU40727 Pinion Yoke with Slinger, (1) QU40097 Pinion Seal, (1) QU40709 Strap & Bolt Kit, (1) QU10918 Pinion Nut/Washer, and (1) S9978 Threadlocker. Link to QK4650 Large Text Individual Product Page
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40847 1310 Series Pinion Yoke QU40847 1310 Series Pinion Yoke directly replaces worn or damaged original equipment Dana 70 u-bolt style pinion end yokes made to take Spicer 1310 series universal joints. U-Joint cup diameter is 1-1/16". Overall width of installed u-joint is 3-7/32". Made in U.S.A.
Link to our QU40847 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40097 Dana 70 Pinion Seal

QU40097 Dana 70 Pinion Seal for many Dodge trucks with Dana 70 Front Axles.
Link to our QU40097 Large Text Catalog Page for more detail & tech info.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40768 1310 Driveshaft U-Bolt Kit QU40768 1310 Driveshaft U-Bolt Kit for Spicer series 1310 universal joints. Use this Kit to replace broken or stripped original u-bolts. Made in U.S.A.
Link to our QU40768 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40727 1410 Series Dana 70 Pinion Yoke QU40727 1410 Series Dana 70 Pinion Yoke for Dodge Ram trucks with Dana 70 Front Axles. Includes a U-shaped slinger that fits over protruding lip on our QU40097 Pinion Seal. Fits 1410 series u-joints with 1-3/16"diameter cups and an overall width of 4-3/16".
Link to our QU40727 Large Text Catalog Page for more detail & tech info
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40709 Universal Joint Strap and Bolt Kit QU40709 Universal Joint Strap and Bolt Kit fits Dana 70 Pinion Yokes in 1989 to 1993 Diesel trucks. QU40709 is made for 1410 series u-joints having 1-3/16"diameter cups and an overall width of 4-3/16".
Link to our QU40709 Large Text Catalog Page for more detail & tech info
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
photo
QU40022 Stock Pinion Nut Genuine Dana-Spicer all-metal, prevailing torque type lock nut is the original equipment replacement part for most Dana-Spicer Model 70 and 70HD front and rear axles. Use 1-5/16" socket. Country of origin unknown
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40023 Hardened Pinion Flat Washer Is a Genuine Dana-Spicer pinion flat washer is the original equipment replacement part for most Dana-Spicer Model 70 and 70HD front and rear axles. Country of origin unknown
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40086 Dana 70 Genuine Dana-Spicer Grade 9 Ring Gear Bolt Has locking teeth under the hex head to prevent loosening under any load conditions. QU40086 is an exact fit, genuine Dana-Spicer replacement part for most Dana 70, and Dana 70HD axles from the mid-1980's on. This bolt, which has a serrated inner face, resists loosening better than smooth faced, aftermarket or first design QU40522 Dana original equipment bolts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40099 Outer Pinion Slinger for Dana Model 60 and 70 Axles is a genuine Dana Spicer original equipment part that fits between the outer pinion bearing and pinion yoke. Made in U.S.A
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40431 Large Spindle and Axle Shaft Bushing for 1958-1978 Dodge Power Wagon®Dana Spicer 70 Closed Knuckle Front Axles Is a flanged Bronze Bushing used in both the spindle and axle housing tubes to support the front axle shafts in 1958-1978 Dodge Power Wagons®
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU15006 6 Bolt Front Hub Gasket for 1958-1968 Dana 70 front axles in Dodge W300 Power Wagon® 4x4 trucks

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50216 8 Bolt Front Hub Gasket for 1969-1975 Dana 70 front axles in Dodge W300 Power Wagon® 4x4 trucks

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40367 Dana 70 Differential Cover Gasket is a genuine Dana-Spicer Model 70 gasket for all 1958-1978 Dodge Dana 70 closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU42030 Hipro Dana 70 Differential Cover Gasket For Model 70 axles. Reusable Dana 70 High Performance Differential Gasket is a genuine Dana part
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
photo
QT1138 Inner Axle Seal Installer For the original QU40382 NOK Inner Axle Seals on 1958 to 1978 Dodge Dana 70 closed knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1130 Inner Axle Seal Installer Thrust Plate Fits all Dana Model 60, Super 60, 61, and Closed Knuckle Model 70 axles from 1967-current on vehicles without CAD (Central Axle Disconnect). See 'Applications' under the Detailed Info Tab
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1133 Press Screw Assembly For Dana/Spicer Model 50, 60, 61, 70, and GM 10 Bolt Axles. Use with the appropriate Seal Installer and Thrust Plate for your application
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4862 Inner Axle Seal Remover Set Is used to drive the QU40382 inner axle seals out of the axle housing bores on all 1958-1978 Dodge 4x4 trucks with Dana 70 front axles. Set includes QT1145 Driver Handle, QT1151 Extension Rod, and QT1214 Seal Remover
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Hubs, Bearings and Seals

top_page
product note

In W200 Heavy-Duty and W300 4x4s with Dana 70 closed knuckle front axles, Dodge used two different front wheel bearing sets depending upon the year, but the wheel seal is the same for all 1958-1974 models. In the W600 with a Model 70, the wheel bearings and seals are different. 1958-1968 axles will have wheel hubs with 6 bolt wheels. 1969-1974 models use 8 bolt wheels.

photo

QU50645 Wheel Seal for 1958-1974 Dodge W200HD, W300 4x4 trucks with Dana 70 Closed Knuckle Front Axles. QU50645 fits both 1958-1968 axles with 6 bolt wheels and 1969-1974 axles with 8 bolt wheels.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50662 1958-1968 Timken® Outer Wheel Bearing Cup For all 1958-1968 Dodge W-200HD and W-300 4x4 trucks with Dana 70 Closed Knuckle Front Drive Axles. 1958-1968 wheel hubs will have a 6 x 7-1/4" Wheel Bolt Circle.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50644 1958-1968 Timken® Outer Wheel Bearing For all 1958-1968 Dodge W-200HD and W-300 4x4 trucks with Dana 70 Closed Knuckle Front Drive Axles.  1958-1968 wheel hubs will have a 6 x 7-1/4" Wheel Bolt Circle.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50402 1958-1968 Timken® Inner Wheel Bearing Cup For all 1958-1968 Dodge W-200HD and W-300 4x4 trucks with Dana 70 Closed Knuckle Front Drive Axles.  1958-1968 wheel hubs will have a 6 x 7-1/4" Wheel Bolt Circle.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50403 1958-1968 Timken® Inner Wheel Bearing For all 1958-1968 Dodge W-200HD and W-300 4x4 trucks with Dana 70 Closed Knuckle Front Drive Axles.  1958-1968 wheel hubs will have a 6 x 7-1/4" Wheel Bolt Circle.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50411 1969-1974 Timken® Outer Wheel Bearing Cup For all 1969-1974 Dodge W-200HD and W-300 4x4 trucks with Dana 70 Closed Knuckle Front Drive Axles. 1969-1974 wheel hubs will have an 8 x 6-1/2" wheel bolt pattern.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50412 1969-1974 Timken® Outer Wheel Bearing For all 1969-1974 Dodge W-200HD and W-300 4x4 trucks with Dana 70 Closed Knuckle Front Drive Axles. 1969-1974 wheel hubs will have an 8 x 6-1/2" wheel bolt pattern.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50396 1969-1974 Timken® Inner Wheel Bearing Cup For all 1969-1974 Dodge W-200HD and W-300 4x4 trucks with Dana 70 Closed Knuckle Front Drive Axles. 1969-1974 wheel hubs will have an 8 x 6-1/2" wheel bolt pattern.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50398 1969-1974 Timken® Inner Wheel Bearing For all 1969-1974 Dodge W-200HD and W-300 4x4 trucks with Dana 70 Closed Knuckle Front Drive Axles. 1969-1974 wheel hubs will have an 8 x 6-1/2" wheel bolt pattern.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11243U Used Front Wheel Hub For 1972-1974 Dodge W200 HD and W300 4x4 Trucks with Single Rear Wheels and Dana 70 Closed Knuckle Front Axles. Hub includes new installed Timken bearing cups and eight used 7/16" x 3/8" lockout hub mounting studs with nuts

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!