Parts for 1957-1971 Dana-Spicer Model 70 Rear Axles in Dodge Trucks

The Dana 70 series rear axle was used in civilian body style, mainly 1 ton trucks. For these older axles we will have some of the common parts, but not much of the Dodge specific components.

Axle Shafts and Axle Shaft Hardware

top_page
photo

QU40577 Tapered Locking Bushing Cone for Dana 70 Rear Axle Shafts fits the factory axle shafts for 1957-1971 Dodge Dana 70 rear axles in 3/4 and 1 ton trucks. QU40577 is an aftermarket replacement split taper axle shaft cone that was redesigned to address the Cone becoming frozen in the tapered axle shaft holes. More Info
Also available while supplies last: QU42009 Original Equipment Split Taper Locking Bushing

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
product note

It has been so many years since I worked on a 1960's era Dodge W300 rear axle that I can not recall from memory the axle shaft spline counts. As far as I can tell from the Dodge parts books, Dodge used Dana 70s with 23 spline axle shaft in the W300 up to 1968. However, Dana shows the 23 spline was replaced by the 35 spline by 1967, so if you need diff parts or axle shafts, ALWAYS verify what you have before ordering parts.

photo

QU15017 23 Spline Rear Internal Differential (Spider) Gear Set Is a genuine New Old Stock (NOS) Dana Gear Set for 1957-1968 Dodge W300 Dana 70 Open Differential Rear Axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets

top_page
product note

In the mid 1970's Dana made a differential cover design change to heavy gauge covers with flat mating flanges. Unlike the previous, thin gauge covers with embossed flanges which were made for use with a cut gasket, the new design, thick gauge covers are designed for sealing with RTV. If you desire, you can still use a gasket with the new type cover by combining the gasket with thin films of RTV. We stock both Ultra Gray RTV Sealant and genuine Dana Gaskets.

photo

QU40367 Rear Differential Cover Gasket For Model 70 Axles. These genuine Dana-Spicer gaskets will also work on Dana 60 axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42030 Hipro Dana 70 Differential Cover Gasket For Model 70 axles. Reusable Dana 70 High Performance Differential Gasket is a genuine Dana part. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40078 Rear Axle shaft Flange Gasket To prevent oil leaks, your Axle Shaft Flange Gaskets should be replaced anytime the axle is removed. These embossed steel gaskets are genuine Dana-Spicer parts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals

top_page
product note

Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations.

photo

TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous

top_page
product note

Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings.

photo

S24200 Blue Threadlocker For spindle and ring gear bolts etc. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S9975 Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90018 Pyroplex® Protection ES Synthetic Grease Provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions! More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90016 SynPower® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90015 Syncon High Performance Synthetic Arctic Grease is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90017 707L Red Grease is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. 1 pound tub. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40218 4 Ounce Limited Slip Lube Is supplied by Dana-Spicer for all Powr-Lok limited-slip differentials in 1957-1971 Dodge D200, W200, D300, and W300 trucks with Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Yokes and Pinion Seals

top_page
product note

Dodge used a number of different Pinion Yokes for 1968-1971 Dana 70 Rear Axles with 29 spline pinion shafts. Replacement recommendations for the various u-joint sizes are:
Detroit 7260 1.078" cups, 2-1/8" inside lock-up: QU10087U Yoke or QK4878 Conversion Yoke Kit
Detroit 7290: 1.125" cups, 2-5/8" inside lock-up: QU40747 Yoke
Detroit 5380: 1.232" cups, 3" inside lock-up: QK4650 Yoke Kit + special order QU40898 Conversion Joint

photo

QU40097 Dana 70 Pinion Seal For 1957-1971 Dodge D200, W200, D300, and W300 trucks with Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40747 7290 Series 29 Spline Dana 60 Pinion Yoke for Dodge Ram Rear Axles Genuine original equipment yoke fits those 1968 to 1971 Dodge Vans and pickups with Dana 70 Rear Axles and Detroit 7290 series inside C-Clip retained universal joints that have 1.125" diameter cups. Inside dimension between Yoke Ears is 2-5/8". More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40763 7290 U-Joint Strap and Bolt Kit For 1961-1971 Dodge trucks and vans with 7290 series rear driveshaft u-joints. Special small head, hardened bolts for attaching the driveshaft to the front axle pinion yoke. 7290 series u-joints have internal C-Clips, 1-1/8" diameter cups and fit yokes measuring 2-5/8" between the ears. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11087U Used 29 Spline 7260 Series Pinion Yoke for Dodge Dana 70 Rear Axles For 1968-1971 Dodge trucks with Dana 70 axles and Detroit 7260 series inside C-Clip retained universal joints that have 1.078" diameter cups. Inside dimension between Yoke Ears is 2-1/8". More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4878 1310 Series x 7260 Series Conversion Pinion Yoke Kit for Dodge Dana 60 Axles Includes a strong, solid cross special conversion u-joint that allows to to replace your damaged original Dodge Pinion Yoke made for 7260 series u-joints with a new pinion yoke that accepts a Spicer series u-joint. Just install the new parts and bolt your old driveshaft to the new pinion yoke! More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40729 7260 U-Joint Strap and Bolt Kit With special small head, hardened bolts for attaching the driveshaft to your rear axle pinion yoke. This Strap and Bolt Kit is used to secure Dodge (Detroit Universal) 7260 series universal joints with 1.078" diameter cups to axle pinion yokes with an inside yoke width of 2-1/8". More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
photo

QU40577 Tapered Locking Bushing Cone for Dana 70 Rear Axle Shafts fits the factory axle shafts for 1957-1971 Dodge Dana 70 rear axles in 3/4 and 1 ton trucks. QU40577 is an aftermarket replacement split taper axle shaft cone that was redesigned to address the Cone becoming frozen in the tapered axle shaft holes. More Info
Also available while supplies last: QU42009 Original Equipment Split Taper Locking Bushing

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Nuts and Spindle Nut Hardware

top_page
photo

QU15004 Flat Tab Spindle Lock Washer Is an original equipment, nonreusable Bend Over Tab Spindle Lockwasher for1972 to early 1979 Dodge D-200, D-250, W-200, W-250, D-300, D350. W-300, and W-350 trucks with Dana-Spicer Model 70 rear axles and 2" Spindle Threads. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!