Parts for 1972-1984.5 Dana-Spicer Model 70 Rear Axles in Dodge Trucks

Dodge used standard Dana 70 rear axles in 1972-1984.5 1 ton trucks and motorhome chassis plus some 400 series 1-1/4 ton motorhomes. The Dana 70HD Heavy-Duty rear axle is found in most 400 series and 500 series Dodge motorhomes of this vintage. The Dana 70HD has heavier gross axle weight ratings and it uses 4-1/8" differential side bearing cups compared to the 3-13/16" diameter cups found in standard Dana 70 rear axles. The standard Dana 70 axles were available in both single and dual rear versions for D300, D350, W300, and W350 1 ton trucks. Early in the 1984 model year, Dodge started using Dana 70U axles with 3-1/2" outside diameter inner pinion bearing cups instead of standard Dana 70 axles which have 4-1/8" outside diameter inner pinion bearing cups. Also, Dodge completely discontinued the use of Dana 70HD axles by the end of the 1984 model year. For truck models, the change date to the Dana 70U axles was for vehicles built after September 7, 1983. Parts for Dodge Dana 70U and Dana 70-2U rear axles can be found on our 1984.5-1993 Dodge Dana 70 Rear Axle Parts webpage.

Axle Identification

top_page
photo

1972-1984.5 Dana Spicer Model 70 Rear Axles in Dodge Ram 250 and 350 series trucks have a Bill of Material Number (BOM) that is either stamped on the rear face of the right axle tube or embossed on a Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows). The BOM number is a 6 digit number beginning with a 6 plus a dash number (ex: 603651-3). They can be used to determine not only the axle model, but also what components the axle was originally built with. We often ask for this number to insure we provide you with the exact parts you need for your truck.

All 1972 to 1984.5 Dodge Model 70 rear axles will have a BOM that starts with "603". If you have a 1984 axle with a BOM that begins with "605", refer to our 1984.5-1993 Dodge Model 70 Rear Axle Parts Web Page.

Each different BOM number signifies an engineering part change which may be minor or major and may involve one or more parts. The dash number indicates the axle ratio and differential type (open or locking). Unfortunately, these tags are often missing on trucks that had prior differential service.

photo

Many Dana Axle have the model number cast somewhere on the cast iron differential housing. (Number is shown at near actual size.)

photo

Not all Dana axles have the model number cast on the housing. It can be very difficult to tell a Dana 60 from a Dana 70, as they have nearly identical covers with exactly the same bolt pattern. One way to tell if you have a Dana 60 or Dana 70 is to measure the cover flange height (yellow arrow). The Dana 60 flange height is approximately 1" high. The Dana 70 flange height is about 1¼" high.

Axle Shafts and Axle Shaft Hardware

top_page
photo
QU40577 Tapered Locking Bushing Cone for Dana 70 Rear Axle Shafts fits the factory axle shafts for 1972-1984.5 Dodge Dana 70 rear axles in 3/4 and 1 ton trucks. QU40577 is an aftermarket replacement split taper axle shaft cone that was redesigned to address the Cone becoming frozen in the tapered axle shaft holes

Also available while supplies last: QU42009 Original Equipment Split Taper Locking Bushing

Link to QU40577 Large Text Individual Product Page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings, Individual

top_page
product note

Over the years, Dana has primarily used Timken bearings when building their axles. For long life and dimensional consistency, Timken bearings are unmatched by any other brand of bearing I have used rebuilding axles over the past 30+ years in the business. When you are a shade tree mechanic dealing with a diff and pinion rebearing job without all the fancy gauging tools we have, you always want your new bearings to be the same overall thickness as the original bearings were when the axle was built so your pinion depth, pinion preload and backlash are within the tolerance limits when you are done with the job. Timken bearings will almost always deliver that type of accuracy, plus the steel quality and surface finish is the world's best.

tech note

1972-1984 vintage Dodge Dana 70 and Dana 70HD rear axles share many of the same parts, but they use different differential bearings and bearing cups. The standard Dana 70 rear axle used in 1972-1984.5 1 ton trucks and motorhome chassis plus some 400 series 1-1/4 ton motorhomes have differential side bearing cups that have an outside diameter of 3-13/16".  The Dana 70HD Heavy-Duty rear axles found in most 400 series and 500 series Dodge motorhomes feature 4-1/8" diameter differential side bearing cups. Also, Dana 70HD axles use a combination of outside bearing cup spacers and shims between the differential and differential bearings to set gear backlash and differential bearing preload. Standard Dana 70 axles just use shims between the bearing and differential case.

photo
QU50400 Timken® Outer Pinion Bearing Cup For Dodge Dana 70 rear axles in 1972-1984.5 1 ton trucks and motor homes.

Please refer to QU50400 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50401 Timken® Outer Pinion Bearing For Dodge Dana 70 rear axles in 1972-1984.5 1 ton trucks and motor homes.

Please refer to QU50401 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50409 Timken® Inner Pinion Bearing Cup For Dodge Dana 70 rear axles in 1972-1984.5 1 ton trucks and motor homes.

Please refer to QU50409 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50602 Timken® Inner Pinion Bearing For Dodge Dana 70 rear axles in 1972-1984.5 1 ton trucks and motor homes.

Please refer to QU50602 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50397 Timken® Dana 70 Differential Bearing Cup is a 3-13/16" outside diameter bearing cup for Dodge Dana 70 rear axles in 1972-1984.5 1 ton trucks and motor homes.

Link to QU50397 Web Catalog Product Page

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50398 Timken® Dana 70 Differential Bearing For Dodge Dana 70 rear axles in 1972-1984.5 1 ton trucks and motor homes.

Please refer to QU50398 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50402 Timken® Dana 70HD Differential Side Bearing Cup is a 4-1/8" outside diameter bearing cup for Dana Spicer Model 70HD Rear Axles in 1972-1973 RM400, 1972-1983 RM500, 1978-1984 CB400, and 1978-1984 MB400 motorhome chassis models

Link to QU50402 Web Catalog Product Page

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50403 Timken® Dana 70HD Differential Side Bearing Cup for Dana Spicer Model 70HD Rear Axles in 1972-1973 RM400, 1972-1983 RM500, 1978-1984 CB400, and 1978-1984 MB400 motorhome chassis models.

Link to QU50403 Web Catalog Product Page

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearing Kits

top_page
photo
QU40259 Differential Side Bearing Set For 1979-1984 Dodge trucks with Dana 70 Rear Axles are original equipment quality replacements. QU40259 Kit includes two each Bearing Cups and Tapered Bearings
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts, Locking

top_page
QU40590 Dana 70 35 Spline Powr-Lok™ Inner Differential Parts Kit For 1972-1984 Dodge Dana 70 Powr-Lok Rear Limted Slip Differentials with 35 spline axle shafts. This Dana Diff Parts Kit Includes the limited slip gears, shafts, clutch discs, and one 4 oz. bottle of limited slip lube
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets

top_page
product note

In the mid 1970's Dana made a differential cover design change to heavy gauge covers with flat mating flanges. Unlike the previous, thin gauge covers with embossed flanges which were made for use with a cut gasket, the new design, thick gauge covers are designed for sealing with RTV. If you desire, you can still use a gasket with the new type cover by combining the gasket with thin films of RTV. We stock both Ultra Gray RTV Sealant and genuine Dana Gaskets.

photo
QU40367 Rear Differential Cover Gasket For Model 70 Axles. These genuine Dana-Spicer gaskets will also work on Dana 60 axles.Dan the Gear Man Tech Note: RTV sealant instead of Gaskets were used during the factory assembly of your axle.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42030 Hipro Dana 70 Differential Cover Gasket For Model 70 axles. Reusable Dana 70 High Performance Differential Gasket is a genuine Dana part.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40078 Rear Axle shaft Flange Gasket To prevent oil leaks, your Axle Shaft Flange Gaskets should be replaced anytime the axle is removed. These embossed steel gaskets are genuine Dana-Spicer parts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your mid 1970's or later Dodge Dana 70.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals

top_page
product note

Dan the Gear Man® Product Note: Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations.

photo
TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous

top_page
product note

Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings.

photo
S24200 Blue Threadlocker For spindle and ring gear bolts etc
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90008 Gear Marking Compound use with QT9404 Brush to check your ring and pinion gear tooth pattern
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90018 Pyroplex® Protection ES Synthetic Grease Provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90016 SynPower ® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90015 Syncon® High Performance Synthetic Arctic Grease Is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90017 707L Red Grease Is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. cartridge or 1 pound tub
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40218 4 Ounce Limited Slip Lube Is supplied by Dana-Spicer for all Powr-Loklimited-slip differentials in 1972-1984 Dodge D200, W200, D250, W250, D200, W300, D350, and W350 trucks with Dana 70 Rear Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Yokes and Pinion Seals

top_page
product note

Dodge used a number of different Pinion Yokes for 1972-1984 Dana 70 Rear Axles. Replacement recommendations for the various u-joint sizes are:
Detroit 7260 1.078" cups, 2-1/8" inside lock-up: QU10087U Yoke or QK4878 Conversion Yoke Kit
Detroit 7290: 1.125" cups, 2-5/8" inside lock-up: QU40747 Yoke
Detroit 5380: 1.232" cups, 3" inside lock-up: QK4650 Yoke Kit + special order QU40898 Conversion Joint

photo
QU40097 Dana 70 Pinion Seal For 1972-1984 Dodge D200, W200, D250, W250, D300, W350, D350, and W350 trucks with Dana 70 Rear Axles.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40747 7290 Series 29 Spline Dana 70 Pinion Yoke for Dodge Ram Rear Axles Genuine original equipment yoke fits those 1972 to 1984 Dodge Vans and pickups with Dana 60 Rear Axles and Detroit 7290 series inside C-Clip retained universal joints that have 1.125" diameter cups. Inside dimension between Yoke Ears is 2-5/8"
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40763 7290 U-Joint Strap and Bolt Kit For 1972-1984 Dodge trucks and vans with 7290 series rear driveshaft bolts for attaching the driveshaft to the front axle pinion yoke. . 7290 series u-joints have internal C-Clips, 1-1/8" diameter cups and fit yokes measuring 2-5/8" between the ears
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU11087U Used 29 Spline 7260 Series Pinion Yoke for Dodge Dana 70 Rear Axles For 1972-1984 Dodge trucks with Dana 60 axles and Detroit 7260 series inside C-Clip retained universal joints that have 1.078" diameter cups. Inside dimension between Yoke Ears is 2-1/8"
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4878 1310 Series x 7260 Series Conversion Pinion Yoke Kit for Dodge Dana 70 Axles Includes a strong, solid cross special conversion u-joint that allows to to replace your damaged original Dodge Pinion Yoke made for 7260 series u-joints with a new pinion yoke that accepts a Spicer series u-joint. Just install the new parts and bolt your old driveshaft to the new pinion yoke!
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40729 7260 U-Joint Strap and Bolt Kit With special small head, hardened bolts for attaching the driveshaft to your rear axle pinion yoke. This Strap and Bolt Kit is used to secure Dodge (Detroit Universal) 7260 series universal joints with 1.078" diameter cups to axle pinion yokes with an inside yoke width of 2-1/8"
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
photo
QU40577 Tapered Locking Bushing Cone for Dana 70 Rear Axle Shafts fits the factory axle shafts for 1972-1984.5 Dodge Dana 70 rear axles in 3/4 and 1 ton trucks. QU40577 is an aftermarket replacement split taper axle shaft cone that was redesigned to address the Cone becoming frozen in the tapered axle shaft holes

Also available while supplies last: QU42009 Original Equipment Split Taper Locking Bushing

Link to QU40577 Large Text Individual Product Page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Nuts and Spindle Nut Hardware

top_page
tech note

Dan the Gear Man® Tech Note: QU40077 Spindle Nuts and QU40089 Spindle Lock Wedges are "Single Use", genuine Dodge and Dana Spicer original equipment components. These parts are designed to be installed once and only once. For safety reasons, you must discard both the nut and wedge if they are removed from the spindle for any reason. Both parts lose a percentage of their resistance to coming off when they are removed. You may hear of cases where this type of factory nut has come off while the truck was being driven. Invariably, these failures involve nuts and wedges that have been reused. I am not aware of a single instance of a properly installed new nut and wedge coming off like that. In my opinion, the original equipment nut design is as safe to use as our double nut sets sold above as long as you follow the rules

photo
QU40077 Locking Rear Spindle Nut for Model 70 Rear Axles Is a genuine original equipment, single use, replacement spindle nut for all 1979 to 1984 Dodge D-200, D-250, W-200, W-250, D-300, D350. W-300, and W-350 trucks with Dana-Spicer Model 70 rear axles and single rear spindle nuts. Use with QU40089. See Tech Note Below!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40089 Spindle Nut Lock Wedge for Model 70 Rear Axles Is a genuine original equipment, single use, replacement Lock Wedge that is designed to prevent QU40077 Spindle Nut from backing off. Use with QU40077. See Tech Note Below!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU15004 Flat Tab Spindle Lock Washer Is an original equipment, nonreusable Bend Over Tab Spindle Lockwasher for 1972 to early 1979 Dodge D-200, D-250, W-200, W-250, D-300, D350. W-300, and W-350 trucks with Dana-Spicer Model 70 rear axles and 2" Spindle Threads. Two Shown. Sold Individually
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
photo
QT1009 Spindle Nut Socket For removing or installing stock rounded hex spindle nuts on 1979-1984 Dodge Ram D250/W250, Ram D350/W350 with Dana 70 Single Rear Wheel or Dual Rear Wheel Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1025 Spindle Nut Socket For removing or installing our Double Spindle Nuts in TK4001 Upgrade Kits on 1979-1984 Dodge Ram D250/W250, D350/W350 with Dana 70 Single Rear Wheel or Dual Rear Wheel Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers
photo
QT1500 SRW Wheel Seal Installer For installing QU40450 Single Rear Wheel Seal in 1979-1984 Dodge Ram 2500, Ram 3500 Models 70 or 80 Single Rear Wheel Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1512 DRW Wheel Seal Installer For QU50075 Seals on 1979-1984 Dodge Ram 2500, Ram 3500 Dana 70 Dual Rear Wheel Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1801 Outer Pinion Bearing Cup Installer and Outer Wheel Bearing Cup Installer (for both Single and Dual Rear Wheel) 1979-1984 Dodge Ram 2500, Ram 3500 with Dana 70 Rear Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1804 Inner Wheel Bearing Cup Installer For 1979-1984 Dodge Ram 2500 and Ram 3500 with Dana 70 Single Rear Wheel Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1806 Inner Pinion Bearing Cup Installer and DRW Inner Wheel Bearing Cup Installer For 1979-1984 Dodge Ram 2500, Ram 3500 Dana 70 Dual Rear Wheel Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals, Individual

top_page
photo
QU40450 Single Rear Wheel Seal For most 1972 to 1984 Dodge 3/4 ton and 1 ton trucks with single rear wheels and Dana 70 rear axles (D250, D350, W250, W350). Conventional (no seating flange) Double lip seal features Wave seal inner lip to contain oil and protective outer wiper lip to exclude brake dust and other contaminants. Use QT1500 for professional installation results
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40451 Original Equipment Dual Rear Wheel Seal For 1972 to 1984 Dodge D300, D350, W300, W350 1 ton trucks with dual rear wheels
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50075 Special Double Lip Dual Rear Wheel Seal Features outer wiper lip to protect the inner lip from brake and road crud. Fits most 1972 to 1984 Dodge 1 ton trucks with dual rear wheels. This is the preferred choice for your dual rear wheel seal. Use QT1512 for professional installation results
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50411 Timken® Outer Bearing Cup For both single and dual rear wheel Dodge trucks with Dana 70 Rear Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50412 Timken® Outer Bearing For both single and dual rear wheel Dodge trucks with Dana 70 Rear Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50413 SRW Timken® Inner Bearing Cup For Single Rear Wheel Dodge trucks with Dana 70 Rear Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50414 SRW Timken® Inner Wheel Bearing For Single Rear Wheel Dodge trucks with Dana 70 Rear Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50377 DRW Timken® Inner Wheel Bearing Cup For Dual Rear Wheel Dodge trucks with Dana 70 Rear Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50376 DRW Timken® Inner Wheel Bearing For Dual Rear Wheel Dodge trucks with Dana 70 Rear Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
product note

The rear wheel bearings in 1972-1984 Dodge Dana 70 Rear axles average about 125, 000 miles before requiring replacement. Torque King® Premium Rear Wheel Bearing and Seal Kits for your Dodge feature premium Timken® bearings and original equipment quality wheel seals because when it comes to rear wheel bearings and seals, only the best will do to safely support the heavy loads your truck hauls. To help you install these vital components properly, Torque King® Master Kits include bearing cup and wheel seal installers. Why use makeshift installation methods that can damage precision surfaces when affordable tools are available to do the job right the first time?

photo
TK8321 Parts Only SRW Torque King® Premium Rear Wheel Bearing and Seal Kit For 1972 to 1984 Dodge 3/4 ton and 1 ton trucks with Single Rear Wheels and Dana 70 rear axles that have 2" spindle threads. (D200, D250, D300, D350, W200, W250, W300, W350). Kit includes Timken® Wheel Bearings, Wheel Seals, Axle Shaft Flange Gaskets, and Threadlocker
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK8304 Master SRW Torque King® Premium Rear Wheel Bearing and Seal Kit With Tools for 1972 to 1984 Dodge 3/4 ton and 1 ton trucks with Single Rear Wheels and Dana 70 rear axles that have 2" spindle threads. (D200, D250, D300, D350, W200, W250, W300, W350). Kit includes Seal and Bearing Cup Installation Tools, Timken® Wheel Bearings, Original Equipment Wheel Seals, Axle Shaft Flange Gaskets, and Threadlocker
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK8322 Parts Only DRW Torque King® Premium Rear Wheel Bearing and Seal Kit For 1972 to 1984 Dodge 1 ton trucks with Dual Rear Wheels and Dana 70 rear axles that have 2" spindle threads. (D300, D350, W300, W350). Kit includes Timken® Wheel Bearings, Double Lip Wheel Seals, Axle Shaft Flange Gaskets, and Threadlocker
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK8305 Master DRW Torque King® Premium Rear Wheel Bearing and Seal Kit With Tools for 1972 to 1984 Dodge 1 ton trucks with Dual Rear Wheels and Dana 70 rear axles that have 2" spindle threads. (D300, D350, W300, W350). Kit includes Seal and Bearing Cup Installation Tools, Timken® Wheel Bearings, Double Lip Wheel Seals, Axle Shaft Flange Gaskets, and Threadlocker
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Hubs

top_page
product note

Dodge used different, non-interchangeable hubs for single and dual rear wheel applications.

photo

QU11288U Used 1972-1984 Dodge Dana Dana 60HD and Dana 70 Single Rear Wheel Hub fits Dodge 3/4 and 1 ton Single Rear Wheel (SRW) trucks with Dana full-floating rear axles with 6200 pound or higher axle weight ratings. Over the years, Dodge used this hub with Dana 60, Dana 60HD, and Dana 70 rear axles in both trucks and 1 ton vans. May or may not include removable 7/16" axle studs used for most applications.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!