Parts for 1984.5-1993 Dana-Spicer Model 70 Rear Axles in Dodge Trucks

We stock a wide selection of parts and tools for Dodge Dana 70 Rear Axles in 1984.5 to 1993 Dodge 3/4 ton and 1 ton trucks. The Dana 70 Rear Axles used by Dodge for 1984.5 to 1993 D250, W250, D350, and W350 trucks are "U" series axles that have a pinion offset of 0.625". The Dana 70U was used from 1984.5 to 1990. The Dana 70-2U can be found on some 1987-1990 trucks and on all 1991-1993 models. Except for Ring and Pinion Sets, most of the common service parts are identical for Dodge Dana 70U and Dana 70-2U axles. Dodge used both single rear wheel and dual rear wheel Dana 70 axles for 1 ton 350 series trucks. The single and dual rear wheel axles have different widths, spindles, hubs, and wheel bearings. All 1989-1993 Diesel 3/4 ton trucks will have a Dana 70 single rear wheel rear axle. Most gas engine D/W 250 series trucks use a Dana 60 instead of a Dana 70 unless equipped with a snow plow package or other heavy-duty option.

Axle Identification

top_page
photo

1984.5-1993 Dana Spicer Model 70 Rear Axles in Dodge Ram 250 and 350 series trucks have a Bill of Material Number (BOM) stamped on a Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows). The BOM number is a 6 digit number beginning with a 6 plus a dash number (ex: 605523-3). They can be used to determine not only the axle model, but also what components the axle was originally built with. We often ask for this number to insure we provide you with the exact parts you need for your truck.

All 1984.5 to 1993 Dodge Model 70 rear axles will have a BOM that starts with "605". If you have a 1984 axle with a BOM that begins with "603", refer to our 1972-1984.5 Dodge Model70 Rear Axle Parts Web Page.

Each different BOM number signifies an engineering part change which may be minor or major and may involve one or more parts. The dash number indicates the axle ratio and differential type (open or locking). Unfortunately, these tags are often missing on trucks that had prior differential service.

photo

Many Dana Axle have the model number cast somewhere on the cast iron differential housing. (Number is shown at near actual size.)

Model 70 Bill of Material Numbers
All 1989-1993 Ram 2500 trucks with the Cummins Diesel used a Dana 70 as did V8 gas 3500 models with any transmission.
1984.5-1985: 605158, 605192, 605214, 605215, 605235, 605269, 605270
1986: 605158, 605235, 605269, 605270
1987: 605311, 605313, 605513,
1988: 605311, 605313, 605386, 605513
1989: 605311,605312, 605313, 605373, 605386, 605407, 605408 ,605513
1990: 605311, 605312, 605313, 605373, 605386, 605407, 605489, 605513
1991: 605508, 605509, 605510, 605511, 605512
1992: 605508, 605509, 605510, 605511, 605512, 605514, 605522
1993: 605508, 605509, 605510, 605511, 605512, 605514, 605522 

 

photo

Not all Dana axles have the model number cast on the housing. It can be very difficult to tell a Dana 60 from a Dana 70, as they have nearly identical covers with exactly the same bolt pattern. One way to tell if you have a Dana 60 or Dana 70 is to measure the cover flange height (yellow arrow). The Dana 60 flange height is approximately 1" high. The Dana 70 flange height is about 1¼" high.

Axle Assemblies, Covers, and Axle Housings

top_page
product note

Depending upon the year and vehicle model, variations in wheel hubs, axle width, shock/spring mounts, brake equipment, axle ratio, pinion yoke, and rear differential cover can make it difficult to find an exact fit Dana 70 replacement axle assembly for your vehicle. We rarely have whole axle assemblies available for vintage Dana 70 applications, but we will list any assemblies or bare housings we have below.

photo

QU40344 Dana 70 Differential Cover Kit For Model 70 Axle. Genuine Dana-Spicer Kit includes steel cover plate, fill plug, and 12 retaining bolts. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shafts and Axle Shaft Hardware

top_page
product note

Dodge used two different axle shaft splines in 1984 to 1993 D350 4x2 and W350 4x4 trucks with Dana 70 rear axles. Left and right axle shafts on a given axle are the same. Single Rear Wheel (SRW) models all have the same length axle shafts. Dual Rear Wheel (DRW) axles came in both narrow track and wide track configurations so you must positively identify your DRW axle before ordering a replacement shaft. Also, the rear axle shafts on trucks built up to November 12, 1990 use studs, split taper bushings, and nuts to secure the axle shafts to the wheel hubs. Grade 9 bolts are used on trucks built after 11-12-1990.

photo

TK40478 1991-1993 Torque King® Single Rear Wheel Dodge Dana 70 32 Spline Rear Axle Shaft is an extra strong, USA made, high-performance axle shaft for the left or right side on all 1991 to 1993 Dodge Ram 250 and 350 trucks with single rear wheel and Dana-Spicer Model 70 Rear Axles. All Ram D-250 and W-250 with the Cummins Diesel Engine have a Dana 70 as do all the D-350 and W-350 single rear wheel trucks with any engine. More Info
Also available while supply lasts: QU40478U Used Rear Axle Shaft

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40582/TK40583 Torque King® 32 SPLINE REAR AXLE SHAFTS for Dual Rear Wheel 1991-1993 Dodge DANA 70 Rear Axles Are extra strong, USA made, high-performance axle shafts for all 1991 to 1993 Dodge Ram 350 trucks with dual rear wheel and Dana-Spicer Model 70 Rear Axles. Also for 1987-1990 wide track axles with axle tag number 605513. More Info

photo

TK40584 Torque King® 35 Spline Rear Axle Shaft for Single Rear Wheel 1987-1990 Dodge DANA 70 Rear Axles Is an extra strong, USA made, high-performance axle shaft for 1984-1990 Dodge Ram 250 and 350 trucks with Dana-Spicer Model 70 SRW Rear Axles. Bolt holes are straight for use with either bolts or studs. More Info
Also available while supply lasts: QU40584U Used 35 Spline Rear Axle Shaft

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40585/TK40586 Series Torque King® 35 SPLINE REAR AXLE SHAFTS for Dual Rear Wheel 1984-1990 Dodge DANA 70 Rear Axles Are extra strong, USA made, high-performance axle shafts for 1984-1990 Dodge Ram 350 trucks with Dana-Spicer Model 70 DRW Rear Axles. Bolt holes are straight for use with either bolts or studs. More Info

photo

QU42009 Original Equipment 7/16" ID Tapered Locking Bushing Cone fits 1990 and earlier Dana 70 full floating rear axle shafts with tapered holes in the drive flange as found in many older Dodge trucks. More Info
Also, QU42009U Used Tapered Locking Bushing Cone while supply lasts.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40577 Tapered Locking Bushing Cone for Dana 70 Rear Axle Shafts fits 1990 and earlier factory rear axle shafts for Dodge Dana 70 rear axles in D/W 250 and D/W 350 trucks. QU40577 is an aftermarket replacement split taper axle shaft cone that was redesigned to address the Cone becoming frozen in the tapered axle shaft holes. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
product note

Almost all the 1984.5-1993 Dodge Dana 70 Rear Axles are equipped with Bendix 12" rear drum brakes. The brake shoe width varied from 2.5" to 3.0" depending upon the exact application. At this time, we mainly stock the important, but hard to find and out of production parking brake mounting hardware. Most 1987-1993 Dodge Ram 250 and Ram 350 trucks are equipped with anti-lock brakes. The rear axle ABS system used on this era of Dodge trucks is rather crude by today's standards. The signal is generated by a toothed steel tone ring (QU40290) pressed on the differential case next to the ring gear. A magnetic pickup is located in the top of the axle housing above the tone ring. Since the unit is sensing differential speed and not the speed of either rear wheel, it can not be used to selectively apply the individual rear brakes.

photo

QU40290 Dana 70 ABS Tone Ring Gets installed on the differential case next to the ring gear on rear Anti Lock Brake equipped 1987-1993 Dodge Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20012 Park Brake Lever Tension Spring For 1984.5-1993 Dodge Dana 70 Rear Axles with Bendix 12" Drum Brakes. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20055 Park Brake Lever Bolt For 1984.5-1993 Dodge Dana 70 Rear Axles with Bendix 12" Drum Brakes.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20013 Park Brake Lever Washer For 1984.5-1993 Dodge Dana 70 Rear Axles with Bendix 12" Drum Brakes. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20015 Park Brake Lever Pivot Bushing For 1984.5-1993 Dodge Dana 70 Rear Axles with Bendix 12" Drum Brakes. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11116 1990-1993 Brake Block Bolt/Axle Vent Fitting Is a genuine original equipment hollow bolt that is used to attach the rear brake junction block to the axle housing and it acts as the axle vent outlet to which you attach the axle vent hose to your 1990 to 1993 Dodge Ram D250, W250, D350, or W350 Dana 70 rear axle. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11119 Dodge Dana 70 Single Rear Wheel Hub and Brake Drum Assembly with eight 1/2" wheel studs for all 1986-1993 D250, W250, D350, and W350  Single Rear Wheel (SRW) Dodge Ram trucks  that have 1/2" wheel studs, 6-5/16" wide, inboard mounted brake drums, and either 12" x 2.5" or 12" x 3" rear brake shoes. QU11119 is a genuine factory assembled, original equipment rear hub and drum assembly that includes Timken® wheel bearing cups.

Link to QU11119 Catalog Page

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11214U Used Left Rear 12" Brake Backing Plate Assembly Fits 1986 to 1993 Dodge D250, W250, D350, W350, and B350 models with Dana 70 full floating rear axles and 12" Bendix type brakes. These assemblies, which fit the drivers side of your big Dodge, are sold as-is and include a good usable backing plate and a good parking brake lever. The brake shoes, wheel cylinder, and hardware may OR MAY NOT be serviceable for your application but are included at no charge for assembly reference. The backing plates and levers can be used with either 12" x 2-1/2" or 12" x 3" brake shoes. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11215U Used Right Rear 12" Brake Backing Plate Assembly Fits 1986 to 1993 Dodge D250, W250, D350, W350, and B350 models with Dana 70 full floating rear axles and 12" Bendix type brakes. These assemblies, which fit the passenger side of your big Dodge, are sold as-is and include a good usable backing plate and a good parking brake lever. The brake shoes, wheel cylinder, and hardware may OR MAY NOT be serviceable for your application but are included at no charge for assembly reference. The backing plates and levers can be used with either 12" x 2-1/2" or 12" x 3" brake shoes. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Timken® Differential and Pinion Bearings, Individual

top_page
product note

If you only need a bearing or two for your 1984-1993 Dodge Dana 70 rear axle, we stock the best: Timken®. For the amount of work it takes to change most axle bearings, the extra cost for a Timken® diff or pinion bearing is a small price to pay for better steel, more uniform surface finish, and accurate, precision ground races.

photo

QU50397 Timken® Differential Bearing Cup For 1984.5-1993 Dodge Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50398 Timken® Differential Bearing For 1984.5-1993 Dodge Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50400 Timken® Outer Pinion Bearing Cup For 1984.5-1993 Dodge Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50401 Timken® Outer Pinion Bearing For 1984.5-1993 Dodge Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50406 Timken® Inner Pinion Bearing Cup For 1984.5-1993 Dodge Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50408 Timken® Inner Pinion Bearing For 1984.5-1993 Dodge Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearing Kits Featuring Timken Bearings

top_page
tech note

Gear set breakage caused by worn and loose Differential Bearings is one of the biggest killers of rear axles. When the differential bearings wear, the backlash between the ring gear and pinion gear will change. Most often, it increases as the ring gear side differential bearing usually takes the brunt of the wear. As the backlash increases beyond approximately 0.010", the chances of breaking a gear tooth increase dramatically. Additionally, a rough and worn differential bearing is very likely to break free and spin on the differential case which will usually mean the case must be replaced. With the Model 70, one often finds the differential bearing cups have worn sideways into the axle housing Sometimes, the wear is minor and can be compensated for by re-shimming the differential, but in most cases, the axle bore faces will need to be re-cut with an Axle Bore Facing Tool such as the QT1000 or the axle housing will need to be replaced. To minimize the chances of wrecking expensive differential parts, I recommend completely re-bearing Dana 60 and 70 axles every 125,000 miles and Dana 80's at or before 150,000 miles.

photo

QU40184 Timken® Differential Bearing Set For Model 70 Axles. Includes two each QU50397 Differential Bearing Cup and QU50398 Differential Bearing. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40182 Timken® Outer Pinion Bearing Set For Model 60 and Model 70 Rear Axles. Superseded. Order one each QU50400 Outer Pinion Bearing Cup and QU50401 Outer Pinion Bearing.

photo

QU40194 Timken® Inner Pinion Bearing Set For Model 70 Rear Axle. Superseded. Order one each QU50406 Inner Pinion Bearing Cup and QU50408 Inner Pinion Bearing.

photo

TK4662 Dana 70 Differential Bearing and Seal Kit Includes Differential and Pinion Bearings, Pinion Seal, Pinion Nut, Outer Pinion Slinger, Pinion Depth Shims, Differential Shims, Pinion Preload Shims, 2 Axle Shaft Flange Gaskets, Threadlocker, and RTV Sealant. More Info
See also QU50438 Timken Bearing Kit with aftermarket small parts

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts, Locking

top_page
product note

Dodge Dana 70 factory Limited Slip rear axles in 1984-1993 Dodge trucks will have Dana Powr-Lok™ Limited Slip Differentials. A ratchet type locking differential, the Detroit No-Spin™ was also available for some years and models. We have no service parts for the No-Spin™, but we do stock parts for the Powr-Lok™ Limited Slip.

photo

QK4604 Powr-Lok™ Rebuild Kit For Dana Model 70. Each kit includes complete clutch packs, 8oz. of limited slip additive, axle shaft flange gaskets, Threadlocker, and RTV sealant. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40503 Clutch Ring For all Dana Model 70 Powr-Lok™ Differentials in 1984.5-1993 Dodge 3/4 and 1 ton trucks. Requires 2 per axle. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40351 Dana 70 32 Spline Powr-Lok™ Inner Differential Parts Kit For 1991-1993 Dodge Dana 70 Powr-Lok Rear Limited Slip Differentials with 32 spline axle shafts. This Dana Diff Parts Kit includes the limited slip gears, shafts, clutch discs, and one 4 oz. bottle of limited slip lube. It is recommended to purchase an additional QU40218 Limited Slip Lube to add to your differential. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40590 Dana 70 35 Spline Powr-Lok™ Inner Differential Parts Kit For 1984.5-1990 Dodge Dana 70 Powr-Lok Rear Limited Slip Differentials with 35 spline axle shafts. This Dana Diff Parts Kit Includes the limited slip gears, shafts, clutch discs, and one 4 oz. bottle of limited slip lube. It is recommended to purchase an additional QU40218 Limited Slip Lube to add to your differential. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40218 4 Ounce Limited Slip Lube Is supplied by Dana-Spicer for all Powr-Lok limited-slip differentials in 1984.5-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles. It is an absolute must to add to your rear differential oil after any drain and refill of axle lubricant. Also used to presoak new clutches when you are rebuilding your limited slip differential. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts, Open

top_page
product note

Except for the Differential Side Gears, 1984.5-1993 Dodge D (4x2) and W (4x4) trucks with Dana 70 Rear Axles and Open Differentials use the same internal parts inside the differential. 35 Spline Side Gears are found in 1984.5-1990 axles and 32 Spline Side Gears equip 1991-1993 axles.

photo

QU40205 Dana 70 32 Spline Differential Parts Kit For 1991-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles and stock open differentials. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40482 Dana 70 Bare Differential Case For 1984.5-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles and stock open differentials. Use with 3.07, 3.54, or 4.10 ratio gear sets. More Info
Limited to stock on hand: QU40482U Used Dana 70 Bare Differential Case Only

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40117 Cross Shaft Retaining Pin For 1984.5-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles and stock open differentials. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40041 Side Gear Thrust Washer For 1984.5-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles and stock open differentials. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40049 Pinion Mate Thrust Washer For 1984.5-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles and stock open differentials. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40116 Differential Cross Shaft For 1984.5-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles and stock open differentials. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40212 Differential Pinion Mate Gear For 1984.5-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles and stock open differentials. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40525 35 Spline Differential Side Gear For 1984.5-1990 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles and stock open differentials. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets

top_page
product note

In the mid 1970's Dana made a differential cover design change to heavy gauge covers with flat mating flanges. Unlike the previous, thin gauge covers with embossed flanges which were made for use with a cut gasket, the new design, thick gauge covers are designed for sealing with RTV. If you desire, you can still use a gasket with the new type cover by combining the gasket with thin films of RTV. We stock both Ultra Gray RTV Sealant and genuine Dana Gaskets.

photo

QU40367 Rear Differential Cover Gasket For Model 70 Axles. These genuine Dana-Spicer gaskets will also work on Dana 60 axles. More Info
Dan the Gear Man Tech Note: RTV sealant instead of Gaskets were used during the factory assembly of your axle

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42030 Hipro Dana 70 Differential Cover Gasket For Model 70 axles. Reusable Dana 70 High Performance Differential Gasket is a genuine Dana part. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40078 Rear Axle shaft Flange Gasket To prevent oil leaks, your Axle Shaft Flange Gaskets should be replaced anytime the axle is removed. These embossed steel gaskets are genuine Dana-Spicer parts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Dodge Dana 70. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals

top_page
product note

Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations.

photo

TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous

top_page
product note

Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts, chemicals, and accessory items that do not neatly fit under our other parts headings.

photo

S24200 Blue Threadlocker For spindle and ring gear bolts etc. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S9975 Anti-Seize Lubricant Use between mating surfaces to prevent rust bonding. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90018 Pyroplex® Protection ES Synthetic Grease provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions! More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90016 SynPower® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90015 Syncon High Performance Synthetic Arctic Grease Is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90017 707L Red Grease Is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. 1 pound tub. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40218 4 Ounce Limited Slip Lube Is supplied by Dana-Spicer for all Powr-Lok limited-slip differentials in 1984.5-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles. For a professional job, we recommend one 4 ounce bottle of lube to soak your clutches and one 4 ounce bottle to add to your rear differential oil after any drain and refill of axle lubricant. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Yokes, Pinion Seals, and Pinion Strap Kits

top_page
product note

Dodge used a number of different Pinion Yokes for 1984-1993 Dana 70 Rear Axles. Replacement recommendations for the various u-joint sizes are:
Detroit 7260 1.078" cups, 2-1/8" inside lock-up: QU10087U Yoke or QK4878 Conversion Yoke Kit
Detroit 7290: 1.125" cups, 2-5/8" inside lock-up: QU40747 Yoke
Detroit 5380: 1.232" cups, 3" inside lock-up: QK4650 Yoke Kit + special order QU40898 Conversion Joint
Spicer 1410: 1.187 cups, 4.187" external lock-up: QU40727 Yoke or QK4650 Yoke Kit

photo

QU40097 Dana 70 Pinion Seal For 1984-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50565 Dana 70 Aftermarket Pinion Seal For 1984-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4650 1410 Series Rear Pinion Yoke Kit For 1989 to 1993 Dodge Ram trucks with the Cummins Diesel engine. Kit includes Pinion Yoke, Pinion Seal, Pinion Nut, U-Joint Straps/Bolts, and Threadlocker. Fits 1410 series u-joints with 1-3/16" diameter cups and an overall width of 4-3/16". More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40727 1410 Series Dana 70 Pinion Yoke For 1989 to 1993 Dodge Ram trucks with the Cummins Diesel engine. Includes a U-shaped slinger that fits over protruding lip on our QU40097 Pinion Seal. Fits 1410 series u-joints with 1-3/16" diameter cups and an overall width of 4-3/16". More Info
Limited to stock on hand: QU40727U Used 1410 Series Pinion Yoke

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40709 Universal Joint Strap and Bolt Kit Fits Dana 70 Pinion Yokes in 1989 to 1993 Diesel trucks. QU40709 is made for 1410 series u-joints having 1-3/16" diameter cups and an overall width of 4-3/16". More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40747 7290 Series Dana 70 Pinion Yoke for Dodge Ram Rear Axles Genuine original equipment yoke fits those 1984 to 1993 Dodge Vans and pickups with Dana 70 Rear Axles and Detroit 7290 series inside C-Clip retained universal joints that have 1.125" diameter cups. Inside dimension between Yoke Ears is 2-5/8". More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40763 7290 U-Joint Strap and Bolt Kit For 1984-1993 Dodge trucks and vans with 7290 series rear driveshaft u-joints. Special small head, hardened bolts for attaching the driveshaft to the front axle pinion yoke. 7290 series u-joints have internal C-Clips, 1-1/8" diameter cups and fit yokes measuring 2-5/8" between the ears. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11087U Used 7260 Series Pinion Yoke for Dodge Dana 70 Rear Axles For 1984-1993 Dodge trucks with Dana 70 axles and Detroit 7260 series inside C-Clip retained universal joints that have 1.078" diameter cups. Inside dimension between Yoke Ears is 2-1/8". More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4878 1310 Series x 7260 Series Conversion Pinion Yoke Kit for Dodge Dana 70 Axles Includes a greaseable special conversion u-joint that allows to to replace your damaged original Dodge Pinion Yoke made for 7260 series u-joints with a new pinion yoke that accepts a conversion series u-joint. Just install the new parts and bolt your old driveshaft to the new pinion yoke! More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40729 7260 U-Joint Strap and Bolt Kit With special small head, hardened bolts for attaching the driveshaft to your rear axle pinion yoke. This Strap and Bolt Kit is used to secure Dodge (Detroit Universal) 7260 series universal joints with 1.078" diameter cups to axle pinion yokes with an inside yoke width of 2-1/8". More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
product note

When it comes to fit, finish, durability, and ease of set-up, no aftermarket gear set equals the matched, original equipment Dana-Spicer Ring and Pinion Sets. I have been building axles for well over 30 years, and to date, I have never had a problem setting up a genuine Dana-Spicer gear set, or have we had to set up a gear set warranty. That is a track record that the aftermarket gear suppliers can only dream about. The bottom line is when you purchase a genuine Dana-Spicer gear set, you get quality equal to original equipment because it IS original equipment. When you select an aftermarket import gear set you will not get a gear set that installs and performs equal to original equipment.

photo

QU40288 Dana 70 3.54 Ring and Pinion Set For 1991-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40493 Dana 70 4.10 Ring and Pinion Set For 1991-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40945 Genuine New Take Out 4.10 Ratio Ring and Pinion Set with Inner Pinion Bearing for 1991-2002 Dodge Ram Dana 70 rear axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note

Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else.

photo

QU40022 Stock Self-Locking Pinion Nut for Model 70 Rear Axles for 1984-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles. This prevailing torque self-locking Pinion Nut is designed to be used only once. Always install a new Pinion Nut on your axle when doing final assembly. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10918 Combination Pinion Nut/Washer Is an updated original equipment replacement part for Dana Model 70 rear axles. The original setup for Dodge Ram Model 70 rear axle used the QU40022 Pinion Nut and QU40023 Pinion Washer, however, with the debut of the Cummins Diesel in 1989, this combination was found to be inadequate as the pinion washer would flex and bend under load. The first solution was to replace the pinion washer with a now discontinued extra-thick Pinion Washer which in turn was replaced by this new design flange nut which replaces both the nut and washer. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40099 Model 70 Outer Pinion Slinger Fits between the outer pinion bearing and pinion yoke on 1984-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40086 Ring Gear Bolt For Dana 70. Genuine Dana-Spicer Grade 9 Bolt has locking teeth under the hex head to prevent loosening under any load conditions. More Info
Dan The Gear Man® Safety Note: Ring Gear Bolts are designed for a single use. They must be replaced after they are removed!

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40206 Dana 70 Differential Shim Kit For 1984.5-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40207 Dana 70 Differential and Pinion Shim Kit For 1984.5-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles. Genuine Dana-Spicer Shim Kit includes Pinion depth shims, pinion preload shims, differential adjusting shims, pinion nut, and cover gasket. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40343 Differential Cap Retaining Bolt For 1984.5-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40535 Axle Shaft to Wheel Hub Bolt Is a genuine Genuine Dana-Spicer 7/16" flange-head Bolt with 9/16" hex head for attaching your full-float axle shafts to the wheel hubs on 1984.5-1993 Dodge D250, W250, D350, and W350 trucks with Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11116 Breather Bolt for 1990-1993 Dodge Rear Axles More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40577 Tapered Locking Bushing Cone for Dana 70 Rear Axle Shafts fits 1990 and earlier factory rear axle shafts for Dodge Dana 70 rear axles in D/W 250 and D/W 350 trucks. QU40577 is an aftermarket replacement split taper axle shaft cone that was redesigned to address the Cone becoming frozen in the tapered axle shaft holes. More Info
Also available while supplies last: QU42009 Original Equipment Split Taper Locking Bushing

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Nuts and Spindle Nut Hardware

top_page
product note

Spindle Nuts have two functions and they are to provide for correct wheel bearing adjustment and to keep your wheel hubs in place. We stock both the original equipment single nut and our Torque King® double spindle nut upgrade sets for your big Dodge Dana 70 rear axle. Stock Spindle Nuts and Spindle Lock Wedges are "Single Use" parts that are designed to be installed once and only once. For safety reasons, you must discard both the nut and wedge if they are removed from the spindle for any reason. Both parts lose a percentage of their resistance to coming off when they are removed. You may hear of cases where this type of factory nut has come off while the truck was being driven. Invariably, these failures involve nuts and wedges that have been reused or improperly installed.

tech note

QU40077 Spindle Nuts and QU40089 Spindle Lock Wedges are "Single Use", genuine Ford and Dana Spicer original equipment components. These parts are designed to be installed once and only once. For safety reasons, you must discard both the nut and wedge if they are removed from the spindle for any reason. Both parts lose a percentage of their resistance to coming off when they are removed. You may hear of cases where this type of factory nut has come off while the truck was being driven. Invariably, these failures involve nuts and wedges that have been reused. I am not aware of a single instance of a properly installed new nut and wedge coming off like that. In my opinion, the original equipment nut design is as safe to use as our double nut sets sold above as long as you follow the rules.

photo

QU40077 Locking Rear Spindle Nut for Model 70 Rear Axles is a genuine original equipment, single use, replacement spindle nut for all 1984 to 1993 Dodge D-200, D-250, W-200, W-250, D-300, D350. W-300, and W-350 trucks with Dana Spicer Model 70 Rear Axles. Use with QU40089. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40089 Spindle Nut Lock Wedge for Model 70 Rear Axles Is a genuine original equipment, single use, replacement Lock Wedge that is designed to prevent QU40077 Spindle Nut from backing off. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4013 Stock Spindle Nut Kit For 1979-2002 3/4 & 1 ton trucks with full float rear axles. Each QUADKIT™ includes Stock Spindle Nuts, Spindle Nut Lock Wedges, Axle Shaft Gaskets, 1/2" drive Spindle Nut Socket, & Threadlocker. More Info
Also available: QK4015 Stock Spindle Nut Kit without Socket.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4000 Torque King® Spindle Nut Upgrade Kit with Socket Offers precise adjustment, superior strength, & long life. Complete Kit includes Spindle Nuts, Tabbed Lock Washers, Thrust Washers, axle shaft Flange Gaskets, Threadlocker, & 1/2" Drive Spindle Nut Wrench. More Info
Note: The spindle nut socket in this Kit does not fit the original spindle nuts. If you don't have a suitable tool to remove the old nuts, order optional QT1009 or QT1009i socket.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4001 Torque King® Spindle Nut Upgrade Kit Offers precise adjustment, superior strength, & long life. Complete Kit includes Spindle Nuts, Tabbed Lock Washers, Thrust Washers, axle shaft Flange Gaskets, and Threadlocker. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4014 Spare Parts Kit For TK4000. Includes steel axle shaft flange gaskets, tabbed spindle lock washers, and Threadlocker. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 70 rear axle in your 1984.5-1993 Dodge.

photo

QT5500 Wheel Bearing Packer Takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the outer wheel bearings and single rear wheel inner bearings on your big Dodge! More Info
Dan The Gear Man Product Note: This Tool is not quite large enough to pack QU50376 Inner Dual Rear Wheel Bearings

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1003 Inner Pinion Bearing Installer For Dana 70. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1088 Press Step Plate Used when Pressing Differential Bearings on or off. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1158 Differential Bearing Installer Makes a hard job easy. The raised inside ridge matches against inner differential bearing race allowing you to easily press or drive on QU50398 differential bearing until the bearing is fully seated against the differential adjusting shims. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1805 Inner Pinion Bearing Cup Installer Has a tapered body so your bearing cup will not be damaged during installation. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1812 Outer Pinion Bearing Cup Installer Has a tapered body so your bearing cup will not be damaged during installation. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1032 Differential Case Spreader
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1009 Spindle Nut Socket More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1500 Wheel Seal Installer For Single Rear Wheel Trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1512 Wheel Seal Installer For Dual Rear Wheel Trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1801 Outer Wheel Bearing Cup Installer For both Single and Dual Rear Wheel trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1804 Inner Wheel Bearing Cup Installer For Single Rear Wheel Trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1806 Inner Wheel Bearing Cup Installer For Dual Rear Wheel Trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals, Individual

top_page
product note

We stock original equipment Dana-Spicer Rear Wheel Seals and Timken® Rear Wheel Bearings for your Dodge plus an optional double lip Rear Wheel Seal for Dual Rear Wheel trucks.

photo

QU40450 Single Rear Wheel Seal for 1984 to 1993 Dodge 3/4 ton and 1 ton trucks with single rear wheels and Dana 70 rear axles (D200, D250, D300, D350, W200, W250, W300, W350). Conventional (no seating flange) Double lip seal features Wave seal inner lip to contain oil and protective outer wiper lip to exclude brake dust and other contaminants. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40451 Original Equipment Dual Rear Wheel Seal for 1984 to 1993 Dodge D300, D350, W300, W350 1 ton trucks with dual rear wheels.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50075 Special Double Lip Dual Rear Rear Wheel Seal features outer wiper lip to protect the inner lip from brake and road crud. Fits 1984 to 1993 Dodge 1 ton trucks with dual rear wheels. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50411 Timken® Outer Bearing Cup For both single and dual rear wheel Dodge trucks with Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50412 Timken® Outer Bearing For both single and dual rear wheel Dodge trucks with Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50413 SRW Timken® Inner Bearing Cup For Single Rear Wheel Dodge trucks with Dana 70 Rear Axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50414 SRW Timken® Inner Wheel Bearing For Single Rear Wheel Dodge trucks with Dana 70 Rear Axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50377 DRW Timken® Inner Wheel Bearing Cup For Dual Rear Wheel Dodge trucks with Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50376 DRW Timken® Inner Wheel Bearing For Dual Rear Wheel Dodge trucks with Dana 70 Rear Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing Kits

top_page
photo

TK4892 Torque King® Rear Wheel Bearing Kit for 1972-1993 Dodge Dana 70 Dual Rear Wheel Axles features premium Timken® bearings. Kit includes Inner and outer wheel bearings/bearing cups. This Kit fits 1972 to 1993 Dodge 4x2 and 4x4 30, or 350 series trucks with Dual Rear Wheel Dana 70 Rear Drive Axles that have 2" Spindle Threads. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Seal & Bearing Kits

top_page
product note

Our Wheel Bearing and Seal Kits feature Timken Bearings and quality Seals. Kits are available with or without installation tools.  

photo

TK4984 Torque King® Rear Wheel Bearing, Seal, and Spindle Nut Kit for 1984-1993 Dodge D350, W350 1-ton and 1989-1993 D250, W250 Diesel 3/4 ton trucks with Single Rear Wheels and Dana 70 rear axles. Kit includes Timken Bearings®, Double Lip Wheel Seals, Steel Axle Shaft Flange Gaskets, Spindle Nuts, Spindle Nut Locks, and Threadlocker. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4985 Torque King® Rear Wheel Bearing, Seal, and Spindle Nut Kit for 1984-1993 Dodge D350, W350 Dual Rear Wheel trucks with Dana 70 rear axles.

More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK8304 Torque King® Master Rear Wheel Bearing and Seal Kit with Installation Tools for 1972-1993 Dodge Dana 70 Single Rear Wheel Axles includes Wheel Bearing Cup Installers, Wheel Seal Installer, Driver Handle, Inner and Outer Wheel Timken® Bearings/Bearing Cups, Inner Wheel Seals, Steel Axle Shaft Flange Gaskets, and Threadlocker for the axle shaft flange bolts. This Kit fits 1972 to 1993 Dodge 4x2 and 4x4 200, 250, 300, or 350 series trucks with Single Rear Wheel Dana 70 Rear Drive Axles that have 2" Spindle Threads.

More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK8305 Torque King® Master Rear Wheel Bearing and Seal Kit with Installation Tools for 1984-1993 Dodge Dana 70 Dual Rear Wheel Axles features premium Timken® bearings and original equipment quality wheel seals because when it comes to rear wheel bearings and seals, only the best will do to safely support the heavy loads your truck hauls. Kit includes Wheel Bearing Cup Installers, Wheel Seal Installer, Driver Handle, Inner and outer wheel bearings/bearing cups, inner wheel seals, steel axle shaft flange gaskets, and Threadlocker for the axle shaft flange bolts. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Hubs

top_page
product note

The Single Rear Wheel (SRW) and Dual Rear Wheel (DRW) Wheel Hubs for Dodge Dana 70 Rear Axles are not interchangeable. The hub length, inner bearing size, and wheel seal size are different for SRW and DRW applications.

photo

QU11288U Used 1984-1993 Dodge Dana Dana 60HD and Dana 70 Single Rear Wheel Hub fits Dodge 3/4 and 1 ton Single Rear Wheel (SRW) trucks with Dana full-floating rear axles with 6200 pounds or higher axle weight ratings. Over the years, Dodge used this hub with Dana 60, Dana 60HD, and Dana 70 rear axles in both trucks and 1-ton vans. May or may not include removable 7/16" axle studs used for most 1990 and prior applications. Limited to stock on hand.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11119 Dodge Dana 70 Single Rear Wheel Hub and Brake Drum Assembly with eight 1/2" wheel studs for all 1986-1993 D250, W250, D350, and W350  Single Rear Wheel (SRW) Dodge Ram trucks  that have 1/2" wheel studs, 6-5/16" wide, inboard mounted brake drums, and either 12" x 2.5" or 12" x 3" rear brake shoes. QU11119 is a genuine factory assembled, original equipment rear hub and drum assembly that includes Timken® wheel bearing cups. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Discontinued Tools

top_page
photo

QT9018 5 Pound Dead Blow Hammer Is just about the first tool you will reach for for a multitude of jobs on your Dodge Ram. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool. Discontinued.

Montana Life

top_page
photo

100 feet from our Store, one of our Clear Creek Trout eyes a grasshopper moments before....

photo

...it lunges out of the water to gulp down the high energy hopper.