Dana 70 Rear Axle Parts for 1994-2002 Dodge Ram 2500 Trucks

We stock an excellent selection of parts for Dana 70 Rear Axles in 1994-2002 Dodge Ram 2500 trucks with gasoline or Cummins Diesel engines. Dodge used Dana 70 Rear Axles in heavier gross vehicle weight Ram 2500 models equipped with gas V-8 engines PLUS Ram 2500 trucks with Cummins Diesel or V-10 gas engines AND automatic transmissions. Dodge did not use the Dana 70 in 1994-2002 Ram 3500 vehicles.

Although the basic design of these Dana axles has been well proven over many decades, you should remember that until the late 1980's, very few work vehicles ever saw the far side of 150,000 miles unless they were totally rebuilt. With the power and durability of newer diesel and fuel injected gas engines and the severe loads they can impose on the drivetrain, you should plan on doing a complete re-bearing job on your 1984-2002 rear axle every 125,000-150,000 miles to prevent catastrophic failures. (See Tech Article Dana-Spicer Rear Drive Axle Component Failures)
A number of engineering changes were made by Dana over the 1994-2002 model years. Most of these occurred between 1999 and 2001. After producing axles for Dodge trucks since the 1950's, Dana lost the contract to produce rear drive axles for Dodge to American Axle Manufacturing (AAM was once the GM Axle Division) effective for the 2003 model year.

Axle Identification

top_page
photo

All 1994-2002 Dana Rear Axles in Dodge Ram trucks have a Bill of Material Number (BOM) stamped on a Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows). The BOM number is a 6 digit number beginning with a 6 plus a dash number (ex: 605523-3). They can be used to determine not only the axle model, but also what components the axle was originally built with. We often ask for this number to insure we provide you with the exact parts you need for your truck.

Each different BOM number signifies an engineering part change which may be minor or major and may involve one or more parts. The dash number indicates the axle ratio and differential type (open or locking). Unfortunately, these tags are often missing on trucks that had prior differential service.

photo

Many Dana Axle have the model number cast somewhere on the cast iron differential housing. (Number is shown at near actual size.)

Model 70 Bill of Material Numbers
All 1994-2002 Ram 2500 trucks with the V10 or Cummins Diesel and automatic transmission used a Dana 70 as did heavy GVW V8 gas 2500 models with any transmission.
 
1994-1995: 605588, 605590, 605722, 605723
1996: 605900, 605786, 605787, 605901, 605879, 605880, 605901
1997: 605879, 605901, 606055, 606012, 606013, 605880
1998: 605980, 605981, 606012, 606013, 606063, 606094, 606095
1999: 606148, 606149, 606164, 606165
2000: 606119, 606120, 606242, 606249, 606250, 606543, 606544
2001-2002: 606266, 606267, 606273, 606274, 606707, 606708
 

 

photo

Not all Dana axles have the model number cast on the housing. It can be very difficult to tell a Dana 60 from a Dana 70, as they have nearly identical covers with exactly the same bolt pattern. One way to tell if you have a Dana 60 or Dana 70 is to measure the cover flange height (yellow arrow). The Dana 60 flange height is approximately 1" high. The Dana 70 flange height is about 1¼" high.

Axle Assemblies , Housings, and Covers

top_page
photo

QU40344 Differential Cover Kit For Model 70 Axle. Genuine Dana-Spicer Kit includes steel cover plate, fill plug, and 12 retaining bolts. More Info

$50.67
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40947 2001-2002 Dana 70 Housing Brand New Dana 70 Rear Axle Housing for 2001.5-2002 Dodge Ram 2500 trucks with rear disc brakes. Includes pinion bearing cups, differential bearing caps, and differential cover. More Info

$950.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shafts and Axle Shaft Flange Bolts

top_page
product note

There is only one axle shaft shaft choice for 1994-2002 Dodge Ram 2500 Dana 70 Rear Axles. Left and right axle shafts are the same length regardless of year or if it is a 4x2 or 4x4 truck.

photo

QU40477 DANA 70 32 SPLINE REAR AXLE SHAFT Is a genuine Dana-Spicer part for all 1994 to 2002 Dodge Ram 2500 with Dana-Spicer Model 70 Rear Axles. All Ram 2500 with the Cummins Diesel Engine or V10 and automatic transmissions have a Dana 70 as do heavy GVW Ram 2500 gas V8 models with any transmission. More Info

$209.64
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40306 Dodge Dana 70 Rear Axle Shaft Flange to Rear Wheel Hub Bolt For securing your full float Dana axle shafts to the wheel hub. Genuine Dana-Spicer 7/16" flange-head Bolts feature a high-strength Grade 9 rating and factory applied threadlocking compound. Fits all Dana 70 full floating rear axles in 1994-2002 Dodge Ram 2500 Trucks. More Info

$2.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brakes

top_page
product note

All 1994-2002 Dodge Ram 2500 trucks are equipped with Anti-Lock Brakes (ABS). Rear Drum Brakes with cable controlled parking brakes were used on all models until mid model year 2001 when rear disc service brakes/drum parking brakes were introduced. 13" x 2-1/2" rear drum brakes equipped 1994-1999 Ram 2500 trucks. For 2000 and 2001, models, the drum brake size is 12-1/8" x 3-1/2".
Axle Vent/Brake Block Bolts are hollow, so it is very easy to twist them off due to rust or over-tightening.

photo

QU40290 Dana 70 ABS Tone Ring Is a genuine original equipment toothed ring that is an interference fit on your Dana 70 differential case. More Info

$30.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11115 1994-1999 Brake Block Bolt/Axle Vent Fitting Is a genuine original equipment hollow bolt that is used to attach the rear brake junction block to the axle housing and it acts as the axle vent outlet to which you attach the axle vent hose to your 1994 to 1999 Dodge Ram 2500 Dana 70 rear axle. More Info

$9.23
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11116 2000-2002 Brake Block Bolt/Axle Vent Fitting Is a genuine original equipment hollow bolt that is used to attach the rear brake junction block to the axle housing and it acts as the axle vent outlet to which you attach the axle vent hose to your 2000 to 2002 Dodge Ram 2500 Dana 70 rear axle. More Info

$10.30
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Individual Timken® Differential and Pinion Bearings

top_page
product note

If you only need a bearing or two for your 1994-2002 Dodge Dana rear axle, we stock the best: Timken®. For the amount of work it takes to change most axle bearings, the extra cost for a Timken® diff or pinion bearing is a small price to pay for better steel, more uniform surface finish, and accurate, precision ground races.

photo

QU50397 Timken® Dana 70 Differential Bearing Cup For Dana 70 Rear Axles in 1994-2002 Dodge Ram 2500 trucks. More Info

$20.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50398 Timken® Dana 70 Differential Bearing For Dana 70 Rear Axles in 1994-2002 Dodge Ram 2500 trucks. More Info

$19.28
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50400 Timken® Dana 70 Outer Pinion Bearing Cup For Dana 70 Rear Axles in 1994-2002 Dodge Ram 2500 trucks. More Info

$10.88
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50401 Timken® Dana 70 Outer Pinion Bearing For Dana 70 Rear Axles in 1994-2002 Dodge Ram 2500 trucks. More Info

$22.71
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50406 Timken® Dana 70 Inner Pinion Bearing Cup For Dana 70 Rear Axles in 1994-2002 Dodge Ram 2500 trucks. More Info

$20.92
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50408 Timken® Dana 70 Inner Pinion Bearing For Dana 70 Rear Axles in 1994-2002 Dodge Ram 2500 trucks. More Info

$36.27
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing and Seal Kits Featuring Timken Bearings and Genuine Dana-Spicer Small Parts

top_page
product note

Gear set breakage caused by worn and loose Differential Bearings is one of the biggest killers of rear axles. When the differential bearings wear, the backlash between the ring gear and pinion gear will change. Most often, it increases as the ring gear side differential bearing usually takes the brunt of the wear. As the backlash increases beyond approximately 0.010", the chances of breaking a gear tooth increase dramatically. Additionally, a rough and worn differential bearing is very likely to break free and spin on the differential case which will usually mean the case must be replaced. With the Model 70, one often finds the differential bearing cups have worn sideways into the axle housing. Sometimes, the wear is minor and can be compensated for by re-shimming the differential, but in most cases, the axle bore faces will need to be re-cut with an Axle Bore Facing Tool such as the QT1000 or the axle housing will need to be replaced. To minimize the chances of wrecking expensive differential parts, I recommend completely re-bearing your 70 rear axle every 125,000 miles.

photo

TK4662 Dana 70 Differential Bearing and Seal Kits for 1984-1999 Dodge include Differential and Pinion Bearings, Pinion Seal, Heavy-Duty combination of Pinion Nut and Washer, Outer Pinion Slinger, Pinion Depth Shims, Differential Shims, Pinion Preload Shims, 2 Axle Shaft Flange Gaskets, Threadlocker, and RTV Sealant. More Info
See also QU50438 Timken Bearing Kit with aftermarket small parts

$284.78
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4853 Dana 70 Differential Bearing and Seal Kits for 2000-2002 Dodge include Differential and Pinion Bearings, Pinion Seal, Heavy-Duty combination of Pinion Nut and Washer, Outer Pinion Slinger, Pinion Depth Shims, Differential Shims, Pinion Preload Shims, 2 Axle Shaft Flange Gaskets, Threadlocker, and RTV Sealant. More Info

$296.08
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differentials and Parts: Factory Limited Slip Clutch Parts

top_page
product note

During the 1994 to 2002 model years, Dodge Ram 2500 trucks using Dana 70 rear axles were available with an optional Dana Powr-Lok™ clutch-type Limited Slip differential. Clutch type differentials wear out under normal use and they will usually need the clutch sets replaced at 100,000 to 125,000 miles to maintain adequate limited slip function.

photo

QK4604 Powr-Lok™ Rebuild Kit For Dana Model 70. Each kit includes complete Clutch Packs, 8oz. of Limited Slip Additive, axle shaft Flange Gaskets, Threadlocker, and RTV sealant. More Info

$149.83
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40503 Clutch Ring For Model 70 Powr-Lok™ Differentials. More Info

$74.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40218 4 Ounce Limited Slip Lube Is supplied by Dana-Spicer for all Powr-Lok and Trac-Lok™ limited-slip differentials in 1994-2002 Dodge Ram 2500 and Ram 3500 trucks with Dana 70 Rear Axles. For a professional job, we recommend one 4 ounce bottle of lube to soak your clutches and one 4 ounce bottle to add to your rear differential oil after any drain and refill of axle lubricant. More Info

$12.75
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40351 Inner Differential Parts Kit For Dana 70 Powr-Lok™. Includes 2 cross shafts, 2 complete clutch packs, 2 clutch rings, 2 side gears, 4 pinion mate gears and limited slip lube. More Info

$836.36
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40304 32 Spline Limited Slip Side Gear For Dana 70 Powr-Lok differentials in 1994-2002 Dodge Ram trucks with 32 spline axle shafts and factory limited slip differentials. Sold individually. More Info

$57.93
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40505 Pinion Mate Gear For Dana 70 Powr-Lok limited slip differentials. Sold individually. More Info

$35.96
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts: Factory Open Differentials

top_page
product note

The 32 spline Dodge Dana 70 Open Differential is adequate for stock or near stock engine horsepower. As power increases, the chances of gear breakage increase substantially. If you are planning an axle ratio change, you need to keep in mind the ring gear offsets are different for 4.10 and numerically lower ratios and 4.56 and numerically higher ratios. So if you are changing from a 4.10 to 4.56 or vice-versa, you MUST change the diff case! The internal parts are the same, but the ring gear flange on the diff case (carrier) is closer to the pinion on the 4.56-up cases.

photo

QU40946NTO Loaded Dana 70 Differential Case Assembly Fast Ratio Loaded New Take Out Genuine Dana Open Differential Case Assembly with 32 spline side gears, ABS tone ring, and differential bearings for 1994-2002 Dodge Ram Dana 70 rear axles with 4.10 and faster axle ratios. More Info

$295.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40482 Dana 70 Bare Differential Case Has 100% genuine Dana-Spicer parts. QU40482 fits 1994-2002 Dodge Dana-Spicer Model 70 rear axles with 4.10 and numerically lower gear ratios (ex: 3.54). More Info

$218.05
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40205 Dana 70 Differential Parts Kit Includes 2 32 spline differential side gears, 2 pinion mate thrust washers, 2 differential pinion mate gears, 2 side gear thrust washers, differential cross shaft, cross shaft retaining pin, ring gear bolts, and differential adjusting shims. More Info

$199.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40117 Cross Shaft Retaining Ping For Model 70 Axles. More Info

$1.30
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40041 Side Gear Thrust Washer For Model 70. More Info

$3.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40049 Pinion Mate Thrust Washer For Model 70. More Info

$2.93
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40116 Differential Cross Shaft For Model 70 Axle. More Info

$32.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Maker

top_page
product note

Dana 70 Rear Axles in 1994-2002 Dodge Ram 2500 Trucks did not have factory differential cover gaskets. The Diff Cover was sealed with RTV sealant. The only factory gaskets were steel gaskets between the wheel hub and axle shaft flange. You can use a diff cover gasket when servicing your truck, but you should never replace the steel axle shaft gaskets with either RTV or paper gaskets.

photo

QU40078 Rear Axle shaft Flange Gasket To prevent oil leaks, your Axle Shaft Flange Gaskets should be replaced anytime the axle is removed. These embossed steel gaskets are genuine Dana-Spicer parts that should be replaced anytime the axle shafts are removed. More Info

$6.26
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42030 Hipro Dana 70 Differential Cover Gasket For Model 70 axles. Reusable Dana 70 High Performance Differential Gasket is a genuine Dana part. More Info

$31.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40367 Rear Differential Cover Gasket For Model 70 Axles These genuine Dana-Spicer gaskets will also work on Dana 60 axles. More Info

$9.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Dodge Ram. More Info

$8.85
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals and Technical Information

top_page
product note

Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations.

photo

TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles. More Info

$20.95
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TSB4008 1994-2002 Dodge Rear Wheel Bearing Adjustment Covers adjustment procedures and Torque Specs for 1994-2002 Dodge 2500 (3/4 Ton) and 3500 (1 Ton) Trucks and Vans with Dana 60, 70 or 80 full-float rear drive axles. More Info

$2.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous

top_page
product note

Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts, chemicals, and accessory items that do not neatly fit under our other parts headings.

photo

S24200 Blue Threadlocker For spindle and ring gear bolts etc. More Info

$6.91
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern. More Info

$3.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S9975 Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding. More Info

$1.62
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90018 Pyroplex® Protection ES Synthetic Grease provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions! More Info

$9.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90015 Syncon High Performance Synthetic Arctic Grease Is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather. More Info

$8.44
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90016 SynPower® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints. More Info

$9.58
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90017 707L Red Grease Is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. QU90017 is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. 1 pound tub. More Info

$7.33
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40218 4 Ounce Limited Slip Lube Is supplied by Dana-Spicer for all Powr-Lok and Trac-Lok™ limited-slip differentials in 1994-2002 Dodge Ram 2500 and Ram 3500 trucks with Dana 70 Rear Axles. For a professional job, we recommend one 4 ounce bottle of lube to soak your clutches and one 4 ounce bottle to add to your rear differential oil after any drain and refill of axle lubricant. More Info

$12.75
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound. More Info

$6.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals

top_page
product note

From 1994 through 1999 all Dodge Ram Dana 70 rear axles used the same one-piece pinion seal. 2000-2002 axles all have two-piece pinion seals consisting of an inner oil seal and an outer wiper seal. The outer wiper V-Seal is the same for all 2000-2002 axles, but two different, non-interchangeable inner oil seals were used so if you have a 2000-2002 truck, you will need to verify which seal your truck needs before ordering.

photo

QU40097 Dana 70 Pinion Seal for 1994-1999 Dana-Spicer Model 70 Rear Axles in Dodge Ram 2500 trucks. More Info

$11.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50565 Dana 70 Aftermarket Pinion Seal for 1994-1999 Dana-Spicer Model 70 Rear Axles in Dodge Ram 2500 trucks. More Info

$5.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40348 Dana 70 1st Design 2000-2002 year Pinion Seal For some 2000-2002 Dana Model 70 rear axles in Dodge Ram 2500 trucks. This seal installs flush with the front of the housing. A band of sealant on the back face of the seal shell will contact the inner face of the seal bore when the seal is fully seated in the axle housing. This seal is used in conjunction with QU40397 V-Seal. More Info

$19.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40402 Dana 70 Flanged Design 2000-2002 year Inner Pinion Seal For some 2000-2002 Dana Model 70 rear axles in Dodge Ram 2500 trucks. This seal fits late production housings with deep seal bores. This seal can be identified by an external flange that seats against the front face of the axle housing. A band of sealant is factory installed to seal against leaks between the seal and housing. This seal is used in conjunction with QU40397 V-Seal. More Info

$15.75
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40397 Dana 70 2000-2002 Outer Pinion Wiper V-Seal Is used on late production Dana Dana Model 70 rear axles that used QU40348 or QU40402 Pinion Seals. The function of this seal is to protect the pinion seal from road splash and other object damage. The flexible wiper lip is in constant contact with the steel flat front face of the pinion seal. More Info

$9.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Yokes and Pinion Yoke Kits

top_page
product note

Dodge used two different, non interchangeable Pinion Yokes for 1994-2002 Dana 70 Rear Axles. Both take the same size u-joint, but use different seals. We stock both individual Yokes and Yoke Kits with seals and hardware.

photo

QK4650 1994-1999 Dana 70 Rear Pinion Yoke Kit For Dodge Dana Model 70 Rear Axle 1994-1999. This Kit includes (1) QU40727 Pinion Yoke with Slinger, (1) QU40097 Pinion Seal, (1) QU40709 Strap & Bolt Kit, (1) QU10918 Pinion Nut/Washer, and (1) S9978 Threadlocker. More Info

$160.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4868 2000-2002 Dana 70 Rear Pinion Yoke Kit For Dodge Dana Model 70 Rear Axle 2000-2002. This Kit includes (1) QU40727 Pinion Yoke without Slinger, (1) QU40348 1st Design Pinion Seal, (1) QU40402 2nd Design Pinion Seal, (1) QU40397 Pinion Wiper V-Seal, (1) QU40709 Strap & Bolt Kit, (1) QU10918 Pinion Nut/Washer, and (1) S9978 Threadlocker. Note: 2000-2002 Model 60 pinion slingers are no longer available, so you need to reuse your old one. More Info

$214.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40727 1994-1999 Dodge Dana 70 Pinion Yoke Includes a U-shaped slinger that fits over protruding lip on our QU40097 Pinion Seal. More Info

$133.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40727X 2000-2002 Dodge Dana 70 Pinion Yoke Yoke only, does not come with slinger. (You need to reuse your old slinger as the flat slingers are no longer available.) More Info

$159.12
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40401 1994-1999 Pinion Slinger Is a genuine Dana replacement Slinger for all 1994-1999 Dodge Dana 70 Rear Axle Pinion Yokes. More Info

$5.80
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
product note

When it comes to fit, finish, durability, and ease of set-up, no aftermarket gear set equals the matched, original equipment Dana-Spicer Ring and Pinion Sets. I have been building axles for well over 30 years, and to date, I have never had a problem setting up a genuine Dana-Spicer gear set or have we had to set up a gear set warranty. That is a track record that the aftermarket gear suppliers can only dream about. The bottom line is when you purchase a genuine Dana-Spicer gear set, you get quality equal to original equipment because it Is original equipment. When you select an aftermarket import gear set you will not get a gear set that installs and performs equal to original equipment.

photo

QU40288 Dana 70 3.54 Ratio Ring and Pinion Kit for Dodge Ram Is a genuine Dana-Spicer Ring and Pinion Kit for Dodge Ram 2500 trucks that includes Matched Ring and Pinion Gear Set, Pinion Bearings, Shims, and Small Parts. More Info

$496.96
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40493 Dana 70 4.10 Ratio Ring and Pinion Kit for Dodge Ram Is a genuine Dana-Spicer Ring and Pinion Kit for Dodge Ram 2500 trucks that includes Matched Ring and Pinion Gear Set, Pinion Bearings, Shims, and Small Parts. More Info

$595.07
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40945NTO Dana 70 4.10 Ratio Ring and Pinion Set for Dodge Ram Is a genuine Dana-Spicer New Take Out Ring and Pinion Set with inner pinion bearing for 1994-2002 Dodge Ram Dana 70 rear axles. More Info

Small Parts

top_page
product note

Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else.

photo

QU40022 Pinion Nut Is a genuine Dana part for 1994-2002 Dodge 70 Rear Axles. More Info

$3.75
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10918 Combination Pinion Nut/Washer Is an updated original equipment replacement part for Dana Model 70 rear axles. The original setup on your 1994-2002 Dodge Ram rear axle used the QU40022 Pinion Nut and a separate, now discontinued extra-thick Pinion Washer. This new design flange nut replaces both the original nut and washer. More Info

$14.43
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40099 Dana 70 Outer Pinion Slinger Is a genuine Dana part that fits between the outer pinion bearing and pinion yoke. More Info

$4.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40345 Dana 70 Outer Pinion Bearing Spacer More Info

$7.68
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40086 Ring Gear Bolt for Dana 70 Genuine Dana-Spicer Grade 9 Bolt has locking teeth under the hex head to prevent loosening under any load conditions. More Info
Dan The Gear Man® Safety Note: Ring Gear Bolts are designed for a single use. They must be replaced after they are removed!

$2.38
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40306 Dodge Dana 70 Rear Axle Shaft Flange to Rear Wheel Hub Bolt For securing your full float Dana axle shafts to the wheel hub. Genuine Dana-Spicer 7/16" flange-head Bolts feature a high-strength Grade 9 rating and factory applied threadlocking compound. Fits all Dana 70 full floating rear axles in 1994-2002 Dodge Ram 2500 Trucks. More Info

$2.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40343 Dana 70 Differential Cap Bolt With 3/4" hex head for all Dana 70 Rear Drive Axles in 1994-2002 Dodge Ram 2500 trucks. Long shoulder, hardened, Grade 8 bolt is a genuine Dana-Spicer original equipment part. More Info

$2.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40206 Differential Shim Kit for Dana 70 Rear axles. Genuine Dana-Spicer Shim Kit includes an assortment of different shim thickness that can be combined to provide the exact thickness required to precisely adjust your gear backlash and bearing preload. More Info

$39.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40207 Differential and Pinion Shim Kit for Model 70 Rear Axles. Genuine Dana-Spicer Shim Kit includes Pinion depth shims, pinion preload shims, differential adjusting shims, pinion nut, and cover gasket. More Info

$79.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Nuts and Spindle Nut Kits

top_page
product note

Spindle Nuts have two functions and they are to provide for correct wheel bearing adjustment and to keep your wheel hubs in place. We stock both the original equipment single nut and our Torque King® double spindle nut upgrade sets for your Dodge Dana 70 rear axle. Stock Spindle Nuts and Spindle Lock Wedges are "Single Use" parts that are designed to be installed once and only once. For safety reasons, you must discard both the nut and wedge if they are removed from the spindle for any reason. Both parts lose a percentage of their resistance to coming off when they are removed. You may hear of cases where this type of factory nut has come off while the truck was being driven. Invariably, these failures involve nuts and wedges that have been reused or improperly installed.

photo

QU40118 Locking Spindle Nut for Dana 70 Rear Axles Is a genuine original equipment, single use, replacement nut for all 1994 to 2002 Dodge Ram 2500 trucks with Dana 70 rear axles. Use with QU40115 Lock Wedge. More Info

$34.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40115 Spindle Nut Lock Wedge For spindle nut on Dana 70 rear axles is a genuine original equipment, single use, replacement lock wedge for all 1994 to 2002 Dodge Ram 2500 trucks. Use to lock QU40118 Nut in place. More Info

$6.45
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4008 and QK4009 Stock Spindle Nut Kits For 1994-2002 Dodge Ram 2500 trucks with Dana 70 full float rear axles. These two Kits feature those critical, genuine original equipment replacement parts needed any time wheel bearing service or wheel hub removal is needed on your big Dodge Ram with single or dual rear wheels. More Info

photo

TK4011 Torque King® Spindle Nut Upgrade Kit with Spindle Nut Socket Offers precise adjustment, superior strength, & long life when replacing your original nonreusable spindle nut/lock wedge with our four piece combination that includes a reusable Inner Thrust Washer, 2 reusable Hex Spindle Nuts, and a nonreusable Bend Over Tab Lockwasher. These Kits fit all single or dual rear wheel 1994 to 2002 Dodge Ram 2500 series trucks. More Info

$154.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4012 Torque King® Spindle Nut Upgrade Kit Offers precise adjustment, superior strength, & long life when replacing your original nonreusable spindle nut/lock wedge with our four piece combination that includes a reusable Inner Thrust Washer, 2 reusable Hex Spindle Nuts, and a nonreusable Bend Over Tab Lockwasher. These Kits fit all single or dual rear wheel 1994 to 2002 Dodge Ram 2500 series trucks. More Info

$146.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4018 Torque King® Spare Parts Kit For 1994 to 2002 Dodge Ram 2500 series trucks equipped with our TK4011 or TK4012 Double Rear Spindle Nut Kits. More Info

$48.71
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 70 rear axle in your 1994-2002 Dodge.

photo

QT1003 Inner Pinion Bearing Installer For Dana 70. More Info

$30.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1088 Press Step Plate Used when Pressing Differential Bearings on or off. More Info

$25.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1158 Differential Bearing Installer Makes a hard job easy. The raised inside ridge matches against inner differential bearing race allowing you to easily press or drive on QU50398 differential bearing until the bearing is fully seated against the differential adjusting shims. More Info

$42.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1805 Inner Pinion Bearing Cup Installer Has a tapered body so your bearing cup will not be damaged during installation. More Info

$22.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1812 Outer Pinion Bearing Cup Installer Has a tapered body so your bearing cup will not be damaged during installation. More Info

$19.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers. More Info

$19.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1032 Differential Case Spreaders For Dana-Spicer Axles. Dana Axles are designed to have a differential bearing preload of .010"-.015". With our Case Spreaders, removing and installing front and rear differentials on your 4x4 is much easier and will help prevent damage to those expensive differential components. More Info

$209.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1801 Outer Wheel Bearing Cup Installer For 1994-2002 Dodge Ram 2500 Dana 70 Rear Axles. More Info

$23.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1804 Inner Wheel Bearing Cup Installer For 1994-2002 Dodge Ram 2500 Dana 70 Rear Axles. More Info

$26.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1009 Spindle Nut Socket For removing or installing stock rounded hex spindle nuts on 1994-2002 Dodge Ram 2500 Dana 70 Rear Axles. More Info

$49.96
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1013 Spindle Nut Socket For removing or installing our Double Spindle Nuts in TK4012 Upgrade Kit on 1994-2002 Dodge Ram 2500 Dana 70 Rear Axles. More Info

$39.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1500 Type 1 SRW Wheel Seal Installer For installing QU40450 Single Rear Wheel Seal in 1994-2002 Dodge Ram 2500 Dana 70 Rear Axles. More Info

$32.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1503 Type 2 SRW Wheel Seal Installer For installing QU40449 Flanged Single Rear Wheel Seal in 1994-2002 Dodge Ram 2500 Dana 70 Rear Axles. More Info

$32.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings (Individual)

top_page
product note

We stock original equipment quality Timken® Rear Wheel Bearings for your 1994 -2002 Dodge Ram 2500 truck with a Dana 70 full floating Rear Axle.

photo

QU50411 Timken® Outer Bearing Cup For 1994-2002 Dodge Ram 2500 trucks with Dana 70 Rear Axles. More Info

$8.15
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50412 Timken® Outer Bearing For 1994-2002 Dodge Ram 2500 trucks with Dana 70 Rear Axles. More Info

$14.46
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50413 Timken® Inner Bearing Cup For 1994-2002 Dodge Ram 2500 trucks with Dana 70 Rear Axles. More Info

$18.66
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50414 Timken® Inner Wheel Bearing For 1994-2002 Dodge Ram 2500 trucks with Dana 70 Rear Axles. More Info

$31.55
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Seals (Individual)

top_page
product note

We stock original equipment quality Wheel Seals and for your 1994 -2002 Dodge Ram 2500 truck with a Dana 70 full floating Rear Axle. Single Rear Wheel axles were built with two types of interchangeable wheel seals during the 1996-1999 model years. Type 1 Seals were used throughout the 1994-2002 era. Type 2 Seals were only original equipment on some 1996-1999 axles.

photo

QU40450 Type 1 Single Rear Wheel Seal For 1994 to 2002 3/4 ton Dodge Ram 2500 Dana 70 rear axles. Conventional (no seating flange) original equipment Double lip seal features Wave seal inner lip to contain oil and protective outer wiper lip to exclude brake dust and other contaminants. More Info

$15.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40449 Type 2 Flanged Single Rear Wheel Seal For 1996 to 1999 3/4 ton Dodge Ram 2500 Dana 70 rear axles. Flanged seal was original equipment on some 1996-1999 trucks but will fit all 1994-2002 hubs. Double lip seal features bidirectional hydrodynamic inner lip to contain oil. More Info

$10.56
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Seal and Bearing Kits

top_page
product note

The rear wheel bearings in 1994-2002 Dodge Dana 70 Rear axles average about 125, 000 miles before requiring replacement. Torque King® Premium Rear Wheel Bearing and Seal Kits for your Dodge feature premium Timken® bearings and original equipment quality wheel seals because when it comes to rear wheel bearings and seals, only the best will do to safely support the heavy loads your truck hauls. To help you install these vital components properly, Torque King® Master Kits include bearing cup and wheel seal installers. Why use makeshift installation methods that can damage precision surfaces when affordable tools are available to do the job right the first time?

photo

TK8356 Parts Only Torque King® Premium Rear Wheel Bearing and Seal Kits For 1994 to 2002 Dodge Ram 2500 3/4 ton trucks. Kit includes Timken® Wheel Bearings, Original Equipment Wheel Quality Seals, Axle Shaft Flange Gaskets, and Threadlocker.

More Info

$186.57
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK8360 Parts Only Torque King® Premium Rear Wheel Bearing and Seal Kits For 1994 to 2002 Dodge Ram 2500 3/4 ton trucks. Kit includes Timken® Wheel Bearings, FLANGED Original Equipment Wheel Quality Seals, Axle Shaft Flange Gaskets, and Threadlocker.

More Info

$184.76
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK8308 Master Torque King® Premium Rear Wheel Bearing and Seal Kits With Tools for 1994 to 2002 Dodge Ram 2500 3/4 ton trucks. Kit includes Seal and Bearing Cup Installation Tools, Timken® Wheel Bearings, UNFLANGED Original Equipment Quality Wheel Seals, Axle Shaft Flange Gaskets, and Threadlocker.

More Info

$291.19
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK8359 Master Torque King® Premium Rear Wheel Bearing and Seal Kits With Tools for 1994 to 2002 Dodge Ram 2500 3/4 ton trucks. Kit includes Seal and Bearing Cup Installation Tools, Timken® Wheel Bearings, FLANGED Original Equipment Quality Wheel Seals, Axle Shaft Flange Gaskets, and Threadlocker.

More Info

$279.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4986 Torque King® Rear Wheel Bearing, Seal, and Spindle Nut Kit for 1994-2002 Dodge Ram 2500 3/4 ton trucks.

More Info

$219.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Hubs

top_page
product note

Several non-interchangeable rear wheel hubs were used on Dodge Dana 70 1994-2002 truck rear axles.

QU11112 2000-2001 Rear Wheel Hub Fits 2000 and 2001 Ram 2500 Dana 70 rear axles with rear drum brakes. QU11112 includes factory installed wheel bearing cups and wheel studs.

More Info

$389.01
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU11113 Dual Rear Wheel Hub for 2000-2001 Ram 3500 with Rear Drum brakes.

More Info

$379.28
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Discontinued Tools

top_page
photo

QT9018 5 Pound Dead Blow Hammer Is just about the first tool you will reach for for a multitude of jobs on your Dodge Ram. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool. Discontinued.