Front Axle Parts for 2000-2002 Dodge Ram 2500 and Ram 35004x4 Trucks with Dana-Spicer Model 60 248 FBI Drive Axles

Dodge Ram 2500 and Dodge Ram 3500 4x4 trucks for the model years of 2000, 2001, and 2002 all use Dana-Spicer Model 60 248 Front Beam Iron (FBI) drive axles. Outwardly, these solid beam axles look very similar to the preceding models; however, relativity few parts were carried over from the 1999 and prior axle. Some of the changes include larger axle shafts, different axle shaft seals, bigger CAD splines, axle mounted ball joints, new tie rod/drag link configuration, different brakes, and redesigned wheel hubs.

During the manufacturing for this generation of axle, further changes were made including new pinion seal designs and a new pinion yoke. Additionally, in mid 2002, the Central Axle Disconnect feature was dropped so the gear set, front driveshaft, and transfer case chain will always rotate when the vehicle is in motion. This last change has both positive and negative aspects. On one hand, getting rid of the sometimes temperamental CAD system increases 4x4 reliability but the downside is these late production trucks generally get poorer fuel mileage due to the constant parasitic draw of the entire front drivetrain when the vehicle is in 4x2 mode.

Axle Identification

top_page
photo

All 2000-2002 Dana Front Axles in Dodge Ram trucks had a Bill of Material Number (BOM) stamped on a Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows) when the vehicle was shipped from the factory. The BOM number is a 6 digit number beginning with a 6 plus a dash number (ex: 610604-2). They can be used to determine not only the axle model, but also what components the axle was originally built with. We often ask for this number to insure we provide you with the exact parts you need for your truck.

Each different BOM number signifies an engineering part change which may be minor or major and may involve one or more parts. The dash number indicates the axle ratio. For 2000-2002 Ram 2500 and 3500 trucks built for civilian use, 3.54 ratio is a -1, 4.10 ratio is -2. Air Force Tow Vehicles all have 7.17:1 gear ratios and the BOM has a -1. Unfortunately, BOM tags are often missing on trucks that had prior differential service so you may have to call your Dodge dealer with your trucks VIN to determine what your truck has.

photo

Anti-Lock Brakes: (If Equipped), 2000-2002: ABS sensor is internal, reading off tone ring inside the wheel hub assembly.

Cover: 10 Bolt, 12" high

Ring Gear: 9-7/8", 12 Bolt

Suspension: Coil spring

Ball Joints: Pressed in steering axle C-forging, nuts at bottom

Ram 2500 Bill of Material Numbers by Year 
2000: 610836, 610837, 610941, 611075, 611076, 611054, 611055
2001: 611054, 611055, 611153, 611154, 611173, 611176
2002: 611153, 611173, 611175, 611176 ,611185, 611223, 2002 (listing incomplete) 
 Ram 3500 Bill of Material Numbers by Year  
2000: 610838, 610942, 611058, 611077, 611056
2001: 611056, 611155, 611153, 61117,
2002: 611174, 611186, 611223, (2002 listing incomplete)
 Military Air Force Tow Vehicle Bill of Material Numbers. All have 7.17 ratio gear sets  
2000: 610899, 611059
2001: 611059
2002: (none listed)

 

Axle Shafts

top_page
product note

Broken Axle Shafts are not very common with the Model 60 unless a worn-out u-joint has been slapped around causing the shaft yokes to give way. Replacing your outer axle shaft is one of those things that is bound to happen while living in the rust belt or cruising ocean beach areas, that can cause the rusted threads to strip from the shaft while removing the outer nut. Choose from our full range of genuine original equipment axle shafts, which feature both precise fit and great strength.

photo

QA40347 Left Axle Shaft Assembly For all 2000-2002 Dodge Ram 2500/3500 4x4 trucks. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40357 Outer Axle Shaft with Slinger For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU40357 Outer Axle Shaft with Slinger also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks
More Info
Also available while supply lasts: QU40357U Used Outer Axle Shaft

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40359 2000-2002.5 Right Inner Axle Shaft (from CAD to U-Joint) for all 2000 early Dodge Ram 2500, 2001 Dodge Ram 2500 and 2002 Dodge Ram 2500 4x4 trucks. QU40359 Right Inner Axle Shaft also fits on all 2000 early Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks
More Info
Also available while supply lasts: QU40359U Used Right Inner Axle Shaft

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40574 2002.5 Right Inner Axle Shaft Is a USA made heavy-duty Torque King® Forged Chrome-Moly Replacement Axle Shaft for 2002.5 Dodge Ram 2500, Ram 3500 4x4 trucks WITHOUT the vacuum controlled Central Axle Disconnect (CAD) system.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40469 Left Inner Axle Shaft For all 2000 to 2002 Dodge Ram 2500 and Ram 3500 4x4 trucks
More Info
Also available while supply lasts: QU40469U Used Left Inner Axle Shaft

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10943 Differential Output or Intermediate Shaft For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU10943 Differential Output or Intermediate Shaft also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks
More Info
Also available while supply lasts: QU10943U Used Differential Output Shaft

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4732 Axle Shaft Nut and Washer Set Fits the outer stub axle shafts on all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QK4732 Axle Shaft Nut and Washer Kit also fits the outer stub axle shafts on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks.
More Info
Also available: QK4732.5 Axle Shaft Nut & Washer Set for 1 side only and QU40114 Nut available separately

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40617 Front Outer Axle Shaft Slinger for 2000-2002 Dodge Ram 2500, Ram 3500 4x4 trucks with Dana 60 front drive axles.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40274U Used CAD Sliding Clutch Collar for 2000-2002 Dodge Ram 2500 and Ram 3500 4x4 trucks with Central Axle Disconnect and couples the differential output shaft and right axle shaft when you activate four wheel drive. Available while supply lasts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Seals and Tool Kits

top_page
product note

All 2000-2002 Ram 2500 and Ram 3500 4x4s have Dana 60 Front Axles with vacuum controlled Central Axle Disconnect (CAD). For the 2002 model year, both CAD and non-CAD axles were used. For axles with CAD, the left and right axle shaft seals are different. Axles without CAD will use two identical seals. The left seal on CAD axles is the same as the left and right seals on axles without CAD. Due to the restricted space and tight fit, it very difficult to correctly install new inner axle seals without special tools made for the job.

photo

QU40298 Left (All) or Right (2002 w/o CAD) Axle Shaft Seal for Ram 2500, Ram 3500 Dana 60 Front Axles A genuine original equipment seal used as the LEFT Axle Seal on all 2000, 2001, and 2002 Dodge Ram 2500 and Ram 3500 4x4 trucks with or without the vacuum controlled Central Axle Disconnect (CAD) system. QU40298 is also used as the RIGHT Axle Shaft Seal on those later production 2002 models that did not have CAD. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40271 Right Axle Shaft Seal is a genuine original equipment seal used for the Right Axle Seal on all 2000, 2001, and 2002 Dodge Ram 2500 and Ram 3500 4x4 trucks WITH the vacuum controlled Central Axle Disconnect (CAD) system. QU40271 IS NOT used on those later production 2002 models that did not have CAD. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4621 2000-2002 Dodge Ram 2500, Ram 3500 Dana 60 Inner Axle Shaft Seal and Tool Kit for CAD Fits 2000-2002 Dodge Ram 2500 and Ram 3500 with vacuum controlled Central Axle Disconnect (CAD). Kit includes installation tool set and original equipment CR brand Seals for both sides. Our unique installer design will press in new your Inner Axle Seals without damage because the CNC Precision Machined Installation Tool cups the seal so force is only applied on the steel seal shell.  Axle Shafts worn or rusty? No problem! Our Install Tool allows you to install either or both Inner Axle Seals to a variable depth to miss grooves worn in your inner axle shafts. Also available are left only and right only Seal and Tool Kits.  More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4802 2002 Ram 2500, Ram 3500 without CAD Inner Axle Oil Seal and Tool Kit to install both the left and right Inner Axle Shaft Seals for all mid to late 2002 model year Dodge Ram 2500 and Ram 3500 4x4 trucks without vacuum controlled Central Axle Disconnect (CAD). Our unique installer design will press in new your Inner Axle Seals without damage because the CNC Precision Machined Installation Tool cups the seal so force is only applied on the steel seal shell.  Axle Shafts worn or rusty? No problem! Our Install Tool allows you to install either or both Inner Axle Seals to a variable depth to miss grooves worn in your inner axle shafts. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note

We offer three different Universal Joints for your hard working Dodge Ram Truck. All are plenty strong for the job, but different manufacturing techniques and seal types will have a major influence on the ultimate life of the joint. Our most popular choice is our TK40715 cold-forged, non-greaseable, original equipment replacement u-joint. The wear-resistant cold-forged cross and superior sealing makes it the best choice for both low maintenance and long life. Greaseable TK40724 u-joints are a greaseable version of our TK40715 joints, giving you the durability advantages of cold-forging and better seals with the option to re-lube the joint at any time for unmatched longevity. QU30332 are hot-forged and are equipped with simple rubber seals. With good maintenance and quality lubricant like our QU90018 Pyroplex Plus grease, these joints will last and last. See our individual product pages for more info.

photo

QU30332 Greaseable Axle U-Joint for Dodge Dana-Spicer Model 60 Front Axle This Greaseable Axle Universal Joint fits all of these Dodge Ram 2500 applications 2000 Dodge Ram 2500, 2001 Dodge Ram 2500 and 2002 Dodge Ram 2500. This Greaseable Axle Universal Joint also fits all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500. Value priced with Hot-Forged cross and flexible rubber seals. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40724 Torque King® Greaseable U-Joint This premium greaseable axle universal joint fits all of these Dodge Ram 2500 applications 2000 Dodge Ram 2500, 2001 Dodge Ram 2500 and 2002 Dodge Ram 2500. This premium greaseable Axle Universal Joint also fits all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500 and 2002 Dodge Ram 3500. Premium Cold-Forged cross and superior pressure-type seals, plus it is greaseable for unmatched life and durability! More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40715 Torque King® Premium Non-Greaseable U-Joint This premium non-greaseable axle universal joint fits all of these Dodge Ram 2500 applications 2000 Dodge Ram 2500, 2001 Dodge Ram 2500 and 2002 Dodge Ram 2500. This Premium non-greaseable axle Universal Joint also fits all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500 and 2002 Dodge Ram 3500. Original equipment type with Premium Cold-Forged cross and superior pressure-type seals. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK42117 Greaseable and Rebuildable CTM 1480WJ Series Performance Axle U-Joint for Dodge Dana 60 Beam Type Front Axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ball Joints

top_page
product note

We have Dana-Spicer Ball Joint Kits for all 3/4 ton 2500 and 1 ton 3500 4x4 trucks. Replace those worn ball joints on your Heavy-Duty Dodge Truck yourself! Please see Below.

Make ball joint removal and reinstallation easy with the optional TS1065 Ball Joint Press Set! Unlike older trucks, the ball joints are pressed into the axle itself, not the steering knuckle, so you can't use a shop press like the 94-99 trucks. I Strongly recommend you have the Press and Tooling tools when removing your old ball joints and pressing the new ones in, it can be a REAL WITCH on 2000-2002 trucks without it!

tech note

Ball Joint failures on 2000-2002 Ram Trucks is a reoccurring problem that will probably plague these trucks for their entire life due to the size of the Ball Joints and the steering geometry of the 2000-2002 Dana 60 Front axle.

The Upper and Lower Ball Joints on these axles are at different angles, in other words the vertical axis of the Upper and Lower Ball Joints are neither in-line or parallel to each other. To compensate for the different arcs of each Ball Joint during turns, the modest sized, straight shank, .855" diameter stud of the greaseable Upper Ball Joint is vertically floating in a plastic sleeve. Consequently, the Upper Ball Joint does not support any weight, it merely keeps the knuckle in place. On these axles, the Upper Ball Joint is not really a Ball Joint at all, instead it is a floating King Pin that is smaller in diameter then King Pins found on 1966-1981 Ford F100 4x2 1/2 ton trucks and light 3/4 ton trucks with GVW's of 4, 700 lbs-6, 900 lbs.

The non-greaseable Lower Ball Joint is load bearing, in fact, the two Lower Ball Joints carry 100% of the front axle weight on your 2000-2002 Dodge Ram 2500 or 3500 truck. Dimensionally, the outside diameter of the Lower Ball Joint is only 3.5% larger than the Ball Joints used on 1972-1986 Jeep CJ's (and other light-duty models of that era) which has somewhere between 1/4 and 1/3 of the front axle weight of the Dodge Ram, plus both the Upper and Lower Ball Joints on the CJ are load bearing. In addition, the Ball Joints used on older models like the Jeep CJ and 1994-1999 Dodge Ram 2500 and 3500* shared the same vertical center line axis and were pre-loaded to compensate for wear. With the 2000-2002 front axle steering geometry using differing Ball Joint angles, no preload is possible, therefore, any wear means loose Ball Joints.

Yes, lack of lubrication with the non-greaseable factory lower Ball Joints can be a factor; however, very few of the failed lower Ball Joints we cut apart are suffering from a lack of lubrication. Replacement Ball Joints in both greaseable and non-greaseable versions are available from us, plus there are even offset upper Ball Joints out there (which in my experience is both short-lived and of limited use). Installing Greaseable Ball Joints and regularly greasing them may provide longer service life, but with the 2000-2002 axle, chances are you will still need to replace the Ball Joints every three to five years. One would not mind the relatively short Ball Joint life so much if these trucks steered better than previous models, were not subject to "Death Wobble", or had longer tire life.

I do not find any allowable Ball Joint tolerances in my Factory Dodge Ram Truck Service Manuals. Generally, with a solid axle, any side to side play is grounds for replacement. Some slight vertical play is probably acceptable for these years.

*1994-1999 Dodge Ram trucks with the Dana 60 Front Axle have Lower Ball Joints that are nearly 10% larger than the 2000-2002 axle. Average Ball Joint life for 1994-1999 trucks is close to 150, 000 miles or 7 to 10 years. All 4 Ball Joints for those years carry weight and are pre-loaded to compensate for wear and dampen steering shocks.

photo

QK4510 2000-2002 Dodge Ram 2500, Ram 3500 Dana OEM Ball Joint Kit Genuine Original Equipment Dana-Spicer Ball Joints (upper Ball Joint is Greaseable, Lower is factory lubed) plus CAD Gasket, Cotter Keys for the Tie Rod Ends, Threadlocker, Anti-Seize, Disc Brake Lube, and RTV sealant. QK4510 Ball Joint Kit fits all 2000, 2001, and 2002 Dodge Ram 2500 and Ram 3500 4x4 trucks. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40219 Dana OEM Ball Joint Set for 2000-2002 Rama 2500, Ram 3500 with hardware for 1 side for fits all 2000-2002 Dana Ram 2500, Ram 3500 Dana 60 front axles. Upper Ball Joint is greaseable, lower ball joint is factory lubed for life.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4776 Greaseable Ball Joint Kit Features Upper and Lower Greaseable Ball Joints. QK4776 fits all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QK4776 Ball Joint Kit also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50219 Greaseable Upper Ball Joint for Dana 60 front axles in 2000-2002 Dodge Ram 2500, Ram 3500 4x4 trucks.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50220 Greaseable Lower Ball Joint for Dana 60 front axles in 2000-2002 Dodge Ram 2500, Ram 3500 4x4 trucks.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1067 Ball Joint Installer Is used with our long-throat C-Frame presses to install both Upper and Lower Ball Joints on 2000-2002 Dodge Ram 2500 and 3500 4x4 trucks with the Dana Spicer Model 60/248FBI front drive axle. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TS1065 5 Piece Ball Joint Press Set easily removes and installs the Ball Joints on all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500 and 2002 Dodge Ram 2500 4x4 trucks. TS1065 also works on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. Specifically designed to make the task of changing the ball joints on your 2000-2002 Dodge RAM truck easy and safe. Long throat design will handle the job! (Unlike standard, short throat presses offered by others) This pro-quality Press Set includes cast iron long reach ball joint press, 2 receivers, one installer, and press stub. Optional tooling is available for other applications. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
product note

Brake parts and steering are the two places you don't want to compromise on. The brake related parts we carry for your 2000, 2001, or 2002 Dodge Ram 3/4 ton or 1 ton truck are all genuine original equipment manufacturer parts that meet or exceed any applicable Federal Motor Vehicle Safety Standard at the time of manufacture. No junk, and no Chinese copied parts.

One thing that has always amazed me is that aftermarket manufacturers such as those who supply most parts from chain stores are under no legal obligation to produce or sell brake parts that meet Federal Motor Vehicle Standards. Interesting, huh?

photo

QU10601 Brake Caliper Anchor Plate to Steering Knuckle Flanged Bolt Is a genuine original equipment Bolt with integral Washer and pre-applied threadlocking compound. Use 2 Bolts per side. For maximum safety, replace these Bolts any time they are removed. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10612 Brake Caliper to Brake Caliper Anchor Plate Bolt Is a genuine original equipment Bolt plated for corrosion resistance. Use QT9206 Torx® Bit to remove or install. Use 2 Bolts per caliper. Installs through QU10692 Sleeve. No Longer Available. More Info

photo

QU10691 Brake Caliper Rubber Bushing Is a genuine OEM part that functions as both a Bushing and protective Boot for QU10692 Sleeve. A very common part requiring replacement due to tears and old age. Even if they still look good, these bushings should be replaced anytime you replace brake pads or a caliper. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10692 Brake Caliper Sleeve Is a genuine OEM part. You will often find these Sleeves showing wear or corrosion damage. They should be replaced whenever you find wear or pitting to minimize the chance of having your caliper stick in place. These Sleeves fit inside QU10691 Bushing. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10963 Right Brake Shield Protects your brake pads and rotors from damaging road grit. QU10963 is a genuine original equipment part that will directly replace your rusted or damaged original Right Brake Shield. Fits both Rear Wheel and Four Wheel Anti-lock Brake Applications on all 2000, 2001, and 2002 Dodge Ram 2500 and 3500 4x4 trucks.
More Info
Also available while supply lasts: QU10963U Used Right Brake Shield

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10964 Left Brake Shield Protects your brake pads and rotors from damaging road grit. QU10964 is a genuine original equipment part that will directly replace your rusted or damaged original Left Brake Shield. Fits both Rear Wheel and Four Wheel Anti-lock Brake Applications on all 2000, 2001, and 2002 Dodge Ram 2500 and 3500 4x4 trucks.
More Info
Also available while supply lasts: QU10964U Used Left Brake Shield

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

CAD Individual Parts (Central Axle Disconnect)

top_page
product note

Need just a part or two for your CAD? We stock all those hard to find small parts that you might need to get your 2000, 2001, or early 2002 Dodge Ram 2500 3/4 ton or Dodge Ram 3500 1 ton truck equipped with the vacuum controlled Central Axle Disconnect back to work in 4x4 mode. Having the front axle kick out when you need it the most can be annoying or it can be the difference between driving home or being stranded in a really bad place. In any case, a malfunctioning CAD system is enough to raise your blood pressure every time the sucker kicks out on you!

photo

QU11061 Vacuum Supply Line Harness for 1998-2002 Dodge Ram with CAD Is a genuine original equipment vacuum harness that runs from the engine back to the transfer case vacuum switch and then down the the transmission crossmember. QU11061 fits Dana 60 front axles in all 1998-2001 Ram 2500, Ram 3500 4x4 trucks plus early production Dana 60 front axles in 2002 Ram 2500, Ram 3500 4x4s with vacuum controlled Central Axle Disconnect (CAD) system. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11062 Front Axle Vacuum Harness For Dodge Ram 4x4's. Includes steel frame lines and flexible axle hoses with connectors. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40317 CAD Axle Shift Housing Genuine original equipment aluminum housing to replace broken or damaged housings on your heavy-duty Ram. For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU40317 CAD Axle Shift Housing also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40090 Metal Reinforced Central Axle Disconnect Gasket Is a genuine original equipment gasket that fits all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500 and 2002 Dodge Ram 2500 4x4 trucks with CAD. QU40090 Gasket also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500 and 2002 Dodge Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10966 CAD Disconnect Switch Genuine original equipment indicator switch screws into QU40317 housing. Also order QU10967 O-Ring. This switch will send a signal to your 4x4 indictor light when the front axle is is locked into 4x4 mode. Fits all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU10966 also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

Dan the Gear Man® Product Note: If you need the Vacuum Switch mounted on your transfer case, please see QU10569 Transfer Case Vacuum Switch Product Page.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10967 O-Ring for CAD Switch Seals oil from leaking between the CAD Housing and Switch. For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU10967 O-Ring also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. Also included in QK4627. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50048 Breather Hose Clamp For Axle Vent Hose original equipment type, 1-ear clamp is used to secure the axle vent hose to the axle breather located on the CAD housing. Fits all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU50048 Clamp also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40156 CAD Shift Fork Pad Is a genuine original equipment part. Two of these Pads are included with every QK4760 CAD Shift Fork. For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. This Shift Fork Pad also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40316 Synthetic Differential Output Shaft Support Bushing Supports the outer end of the differential output shaft on all 2000-2002 Dodge Ram 2500 and Ram 3500 4x4 trucks with CAD. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40107 CAD Right Inner Axle Shaft Support Bushing Is a very common part to wear out. This genuine, original equipment bushing fits inside the inner end of your right inner axle shaft. It is the only direct support for right axle shaft assembly besides the wheel hub. For all 2000-2002 Dodge Ram 2500 and Ram 3500 4x4 trucks with CAD. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40274U Used Clutch Collar For all 2000 early Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU40274U Clutch Collar also fits on all 2000 early Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. Available while supplies last. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40162 CAD Actuator Retaining E-Clip is used to secure your Shift Fork to the Vacuum Actuator Shift Rod (QK4904) on Dodge and Jeep 4x4s with vacuum controlled Central Axle Disconnect (CAD) systems. Order (2) QU40162 for original equipment Actuators. Order (1) QU40162 and (1) QU40516 for most Aftermarket Actuators. For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. This C-Clip also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. Sold individually. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40223 E-Clip is used to Secure your Vacuum Actuator to the aluminum shift housing (QU40317) on Dodge and Jeep 4x4s with vacuum controlled Central Axle Disconnect (CAD) systems. Of the 3 E-Clips used on CAD axles, this is the largest one. Fits all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU40223 C-Clip also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

 

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40516 E-Clip For use with most aftermarket CAD Vacuum Actuators to fit the inboard groove on the Actuator Shaft (See QK4904). Does not fit original equipment Vacuum Actuators. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40272 O-Ring is used on Dodge 4x4 vehicles with vacuum controlled Central Axle Disconnect (CAD) systems. This O-Ring fits in a groove machined in the vacuum actuator mounting stem (QU40224) that slips inside the shift housing (QU40317/QU42119). More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

CAD Parts and Tool Kits (Central Axle Disconnect)

top_page
photo

QK4627 Small Parts Kit includes: QU40090 CAD Gasket, QU40272 O-Ring, 2 QU40156 Shift Fork Pads, QU50048 Hose Clamp, and the 3 E-Clips for the original equipment motor and shift fork mounting. For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QK4627 Small Parts Kit also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

Dan the Gear Man® Tech Note: The two smaller E-Clips supplied in this Kit fit the original equipment actuator shaft. Most aftermarket shafts have at least one groove that is machined to a smaller diameter. The original equipment clips supplied in this Kit will not fit those smaller diameter grooves.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40224 Vacuum Shift Kit For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU40224 Vacuum Shift Kit also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. Kit includes: vacuum actuator, QK4627 CAD Parts Kit and new retaining bolts with lock washers.

More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4626 Right Axle Bushing Kit For all 2000-2002 Dodge Ram 2500 and Ram 3500 4x4 trucks with CAD. Kit includes 1 QU40316 Differential Output Shaft Bushing and 1 QU40107 Right Inner Axle Shaft Support Bushing. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4760 Shift Fork Kit For all 2000-early 2002 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QK4760 Shift Fork Kit also fits on all 2000 early Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. Kit includes 2 QU40156 Shift Fork Pads and 1 Shift Fork. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42119 Replacement CAD Axle Shift Housing Kit aluminum housing is used to replace broken or damaged housings on your heavy-duty Ram. For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU42119 CAD Axle Shift Housing Kit also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential & Pinion Timken Original Equipment Quality Bearings

top_page
photo

QU50397 Timken® Differential Bearing Cup For Model 60 Front Axles for all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU50397 Differential Bearing Cup also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50398 Timken® Differential Bearing For Model 60 Front Axles for all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU50398 Differential Bearing also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40184 Timken® Differential Bearing Set For Model 60 Front Axles for all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU40184 Differential Bearing Set also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50400 Timken® Outer Pinion Bearing Cup For Model 60 Front Axles for all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU50400 Outer Pinion Bearing Cup also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. For an original equipment Outer Pinion Bearing Cup and Cone Set, see QU40182. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50401 Timken® Outer Pinion Bearing For Model 60 Front Axles for all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU50401 Outer Pinion Bearing also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. For an original equipment Outer Pinion Bearing Cup and Cone Set, see QU40182. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50406 Timken® Inner Pinion Bearing Cup For Model 60 Front Axles for all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU50406 Inner Pinion Bearing Cup also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. For an original equipment Outer Pinion Bearing Cup and Cone Set, see QU40183. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50407 Timken® Inner Pinion Bearing For Model 60 Front Axles for all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU50407 Inner Pinion Bearing also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. For an original equipment Outer Pinion Bearing Cup and Cone Set, see QU40183. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing & Seal Kits Featuring Genuine Timken® Bearings and Dana-Spicer Spicer Small Parts

top_page
photo

TK4855 Torque King Premium Quality Front Differential Bearing and Seal Kit For your 2000-2002 Dodge Ram heavy-duty 4x4 truck features 100% Timken® Bearings and genuine Dana-Spicer Small Parts. TK4855 includes: QU50400 Outer Pinion Bearing Cup, QU50401 Outer Pinion Bearing, QU50406 Inner Pinion Bearing Cup, QU50407 Inner Pinion Bearing, 2 QU50397 Differential Bearing Cups, 2 QU50398 Differential Bearings, QU40356 Pinion Preload Spacer, QU40348 Pinion Seal, QU40397 Pinion V-Seal, QU40095 Outer Pinion Slinger, QU40022 Pinion Nut, QU40023 Pinion Washer. More Info

Dan the Gear Man® Product Note: TK4855 Kit does NOT include QU40271 or QU40298 (2000-2002.5 with CAD) or 2 QU40298 (2002 no CAD) Axle Shaft Seals. Order those separately or as part of QK4621 Axle Shaft Seal Kit with CAD; or QK4802 (No CAD).

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4843 Torque King Premium Quality Front Differential Master Service Kit For your 2000-2002 Dodge Ram heavy-duty 4x4 truck with CAD features 100% Timken® Bearings and genuine Dana-Spicer Small Parts. QK4843 includes: QU50400 Outer Pinion Bearing Cup, QU50401 Outer Pinion Bearing, QU50406 Inner Pinion Bearing Cup, QU50407 Inner Pinion Bearing, 2 QU50397 Differential Bearing Cups, 2 QU50398 Differential Bearings, QU40356 Pinion Preload Spacer, QU40365 Pinion Depth Shims, QU40206 Differential Shims, 12 QU40086 Ring Gear Bolts, QU40348 Pinion Seal, QU40397 Pinion V-Seal, QU40095 Outer Pinion Slinger, QU40022 Pinion Nut, QU40023 Pinion Washer, QU40298 Left Axle Shaft Seal, QU40271 Right Axle Shaft Seal, QU90008 Gear Marking Compound, 82194 Ultra RTV Sealant, 24200 Threadlocker, and QT9404 Brush. More Info

Dan the Gear Man® Product Note: Since it is not necessary to remove the small differential gears for most axle projects, we do not include QU40519 Lock Pin for the Cross Shaft, QU40517 Side Gear Thrust Washers, or QU40518 Pinion Mate Gear Thrust Washers in this Kit.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differentials and Differential Parts

top_page
product note

2000-2002 Dodge Ram Dana 60 front axles have 1-3/8" diameter 32 spline inner axle shafts. These larger axle shafts are stronger than the 1-5/16" 30 spline axle shafts used on 1994 to 1999 Rams. The bad news is the 32 spline front shafts were only used on 2000-2001-2002 Ram Dana 60s, so price and parts availability for the internal gears and loaded cases suffers due to the limited use of these size axle splines. (Contemporary Ford Super Duty Dana 60 axles have 1-1/2" 35 spline axle shafts.)

photo

QU40485 32 Spline Dodge Dana 60 Front Differential Parts Kit For all Dana 60 Front Axles in 2000-2002 Dodge Ram 2500 Ram 3500 4x4 trucks. Includes Gear, Trust Washers, Cross Shaft, Ring Gear Bolts, and Lock Pin. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40254 Bare Differential Case Kit Is a genuine Dana-Spicer Case for 4.10 and 3.54 ratio ring and pinion sets. Kit includes Differential Case, Ring Gear Bolts, and Differential Shim Kit. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20271U Good Used Differential Case Dana Model 60 is a genuine Dana-Spicer part. QU20271U fits many Dana-Spicer Model 60 front or rear axles with open differentials and 4.30 or numerically lower gear ratios (ex: 3.54). Also fits some Model 61 axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40514U Used Dana 60 Loaded Differential Case for 2000-2002 Dodge Ram Is a genuine Dana-Spicer Loaded Diff Case for 2000-2002 Dodge Ram 2500, Ram 3500 4x4 trucks with 4.10 or 3.54 ratio Dana 60 front axles. (New Case No Longer Available) More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40518 Dana 60 Differential Pinion Mate Thrust Washer Is a genuine Dana-Spicer original equipment Thrust Washer that fits all 2000-2002 Dana 60 front axles in 2000-2002 Dodge Ram 2500, Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40519 Dodge Dana 60 Lock Pin for Differential Cross Shaft Is a genuine Dana-Spicer original equipment Thrust Washer that fits all 2000-2002 Dana 60 front axles in 2000-2002 Dodge Ram 2500, Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40520 Dodge Dana 60 Differential Cross Shaft Is a genuine Dana-Spicer original equipment part that fits all 2000-2002 Dana 60 front axles in 2000-2002 Dodge Ram 2500, Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Makers

top_page
photo

QU40367 Rear Differential Cover Gasket For Model 70 Axles. These genuine Dana-Spicer gaskets will also work on Dana 60 axles. More Info

Dan the Gear Man® Tech Note: RTV sealant instead of Gaskets were used during the factory assembly of your axle.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Dodge Ram. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40090 Metal Reinforced Central Axle Disconnect Gasket For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500 and 2002 Dodge Ram 2500 4x4 trucks. QU40090 Gasket also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500 and 2002 Dodge Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hub Assemblies

top_page
product note

Unitized Front Wheel Bearing and Hub Assemblies for 2000 to 2002 Dodge Ram 4X4 trucks with the Dana-Spicer Model 60 front axle. This will include ALL 2000-2002 Ram 2500 and Ram 3500 4x4 trucks regardless of engine or vehicle weight rating. The front wheel bearings on 2000-2002 Dodge 4x4 3/4 and 1 ton 4x4 trucks are of unitized construction. They are not serviceable and no individual replacement parts are available for them. If your front wheel bearings are noisy or loose, you need to replace the hub and bearing assembly with one of these original equipment hub assemblies. 

photo

QK4555 Hub Assembly Kit For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks with 4 Wheel ABS. QK4555 Hub Assembly Kit also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks with 4 Wheel ABS. Kit includes Hub, threadlocker, disc brake lube, anti-seize, dielectric grease, and cotter key. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4574 Hub Assembly Kit For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QK4574 Hub Assembly Kit also fits on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks with Rear Wheel ABS. Kit includes Hub, threadlocker, disc brake lube, and anti-seize. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hub Kits, Performance Rebuildable by Dynatrac and Yukon

top_page
product note

Replace those troublesome and expensive factory unit hubs. Upgrade your big Ram 4x4 to have rebuildable Front Wheel Hubs with replaceable Timken® Tapered Wheel Bearings, and Fuel Saving Lock Out Hubs. We stock Dynatrac Free-Spin™ and Yukon Spin Free® performance Serviceable Front Hub Kits for your Ram. For Single Rear Wheel (SRW) Ram 2500, Ram 3500, kits are available with your choice of Dynaloc™, Mile Marker®, Warn®, or Yukon® Lockout Hubs. Have a Ram 3500 dually? Check out our Yukon Spin Free® Kits with direct-fit wheel hubs that eliminate the need for a separate wheel adapter. Want the ultimate Kit that has it all in one package? See Our Torque King Master Kits featuring a USA made Dynatrac Free-Spin™ Kit, 3 Hub Lock choices, premium Axle U-joints, Install Tools, and more!
Benefits of These Kits include:
Better Fuel Mileage
Reduced Wear and Tear on the front axle gears, front driveshaft, and transfer case
Easy to service and/or replace the popular, readily available, economical tapered front wheel bearings
Allow operation in 4x2 low range when hubs are unlocked for backing up trailers or other low speed maneuvering

photo

TK4900 Series Torque King® Master Front Serviceable Wheel Hub and Lockout Hub Kits with Dynatrac Free-Spin™ Kit, Axle U-Joints and Install Tools for 2000-2002 Dodge Ram 2500, Ram 3500 trucks with single rear wheels. TK4900 Series Kits include all the parts, special assembly tools, and extras needed to upgrade your heavy-duty Ram 4x4's front axle to low-cost serviceable wheel bearings and your choice of fuel-saving lockout hubs. The heart of all these comprehensive Kits are USA made Dynatrac Front Free-Spin™ Hub Kit PLUS, our comprehensive Master Kits ALSO include Spindle Nut Socket, Torque King® Factory Lubed Axle U-Joints, wheel seal tools, bearing packer, synthetic wheel bearing grease, threadlocker, and anti-seize compound. Kits direct fit single rear wheel trucks. Will also fit dually models with optional wheel adapters, see More Info Tech Notes if you have a Dodge Ram 3500 with Dual Rear Wheels (DRW).

More Info

 

photo

TK11200 Series Dynatrac Free-Spin™ Kits for 2000-2002 Dodge Ram 2500, Ram 3500 TK11200 Series Kits include the conversion parts and your choice of fuel-saving lockout hubs to upgrade your heavy-duty Ram 4x4's front axle. Each Kit includes a complete, USA made Dynatrac Front Free-Spin™ Hub Kit with heat-treated chromoly spindles, spindle bearings, spindle seals, Timken® wheel bearings, Timken® or Dana wheel seals, 35-spline 1.50-inch chromoly outer shafts, 8 bolt wheel hubs, your choice of Hub Locks, double spindle nut kit, and instructions. All Kits direct fit single rear wheel trucks. Will also fit dually models with optional wheel adapters, see More Info Tech Notes if you have a Dodge Ram 3500 with Dual Rear Wheels (DRW).

More Info

photo

Y100011 Yukon Spin Free® Front Locking Hub Conversion Kit for 2000-2002 Dodge Ram 2500, Ram 3500 Single Rear Wheel 4x4s Y100010 Series Kits fit 2000-2002 Dodge AAM front axles in Ram 2500, Ram 3500 4x4 with single rear wheels. The Yukon worry free, Spin Free® Kit replaces the vulnerable and expensive factory unit bearings with tapered bearings and races. The result is not only a design which is easier and more economical to service, but one that offers significant increases in mileage per gallon. This hub kit also includes low-profile Yukon Hardcore premium locking hubs, giving you more driving selectability. This kit includes new wheel hubs, spindles, high strength Yukon 4340 Chrome-Moly outer axles, low-profile Yukon Hardcore premium locking hubs, Timken bearings, high quality seals and all hardware for installation. 

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

Y100000 Yukon Spin Free® Front Locking Hub Conversion Kit for 2000-2002 Dodge Ram 3500 Dual Rear Wheel 4x4s Y100000 Series Kits fit 2000-2002 Dodge AAM front axles in Ram Ram 3500 4x4 with dual rear wheels. The Yukon worry free, Spin Free® Kit replaces the vulnerable and expensive factory unit bearings with tapered bearings and races. The result is not only a design which is easier and more economical to service, but one that offers significant increases in mileage per gallon. This hub kit also includes low-profile Yukon Hardcore premium locking hubs, giving you more driving selectability. This kit includes new wheel hubs with integral wheel adpaters, spindles, high strength Yukon 4340 Chrome-Moly outer axles, low-profile Yukon Hardcore premium locking hubs, Timken bearings, high quality seals and all hardware for installation. 

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals and Technical Service Bulletins

top_page
photo

TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles Complete step-by-step, color illustrated guide for replacing differential and pinion bearings on all Dana-Spicer Model 30, 35, 44, 50, 60, 61, 70, 70HD, and 80 front or rear drive axles. 26 pages with over 75 color photographs! Available in print version. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TSB4620 Inner Axle Seal Replacement More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts

top_page
photo

QK4732 Axle Shaft Nut and Washer Set Fits the outer stub axle shafts on all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500 Dodge Ram, and 2000 Dodge Ram 2500 4x4 trucks. QK4732 Axle Shaft Nut and Washer Kit also fits the outer stub axle shafts on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4732.5 Half Axle Shaft Nut and Washer Set Fits the outer stub axle shafts on all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500 Dodge Ram, and 2000 Dodge Ram 2500 4x4 trucks. QK4732.5 Axle Shaft Nut and Washer Kit also fits the outer stub axle shafts on all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40114 Spindle Nut Is a genuine original equipment replacement part. Also available in QK4732 Kit with the flat washer and cotter key. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S24200 Blue Threadlocker More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90008 Gear Marking Compound More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Yokes and Pinion Seals

top_page
product note

2000-2002 axles all have two-piece pinion seals consisting of an inner oil seal and an outer wiper seal. The outer wiper V-Seal is the same for all 2000-2002 axles, but two different, non-interchangeable inner oil seals were used so if you have a 2000-2002 truck, you will need to verify which seal your truck needs before ordering.

photo

QU40379 Front Pinion Yoke for 2000-2002 Dodge Ram 2500 and 3500 4x4 trucks. New Yoke has been superseded to QU40509.
Also available while supply lasts: QU40379U Used Front Pinion Yoke
More Info

photo

QK4840 Front Pinion Yoke Kit Includes all the small parts to get you back on the road! QK4840 Pinion Yoke Kit is a replacement kit to fit 2000 to 2002 Dodge Ram 2500, Ram 3500 4x4 trucks. The Yoke in this Kit is 1/4" shorter than the QU40379 original pinion yoke, but can be used with no slinger AND your driveshaft slip yoke can safely extend 1/4". More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40348 2000-2002.5 Dana 60 Flush Design Pinion Seal For early to mid production 2000-2002 Dana Model 60 Dodge Ram front axles. This seal installs flush with the front of the housing. A band of sealant on the back face of the seal shell will contact the inner face of the seal bore when the seal is fully seated in the axle housing. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40402 Dana 60 Flanged Design partial 2002 year Inner Pinion Seal For later production (mainly 2002) Dana Model 60 front axles in Dodge Ram 2500, Ram 3500 trucks. This seal fits late production housings with deep seal bores. This seal can be identified by an external flange that seats against the front face of the axle housing. A band of sealant is factory installed to seal against leaks between the seal and housing. This seal is used in conjunction with QU40397 V-Seal. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40397 Pinion Wiper V-Seal Is used on all 2000-2002 Dana Model 60 front axles to protect QU40348 Pinion Seal from road splash and grit. The flexible wiper lip is in constant contact with the steel flat front face of the pinion seal. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
product note

Unless your axle has run out of oil or it is severely abused, you will probably never have to replace your original ring and pinion set. However, if you do need one, we stock original equipment Dana-Spicer Gear Sets for your Ram's Model 60 front axle. These genuine gear sets are not cheap when compared to the host of knock off Asian import gear sets being pushed into the market place by vendors focused on getting the cheapest stuff they can. Well, like anything, you get what you pay for. I have been setting up Dana Gear Sets since the mid 1970's to date, and I have never had a setup problem with a genuine Dana-Spicer Gear Set. The same is not true for the aftermarket parts. Besides having sloppy machining, most aftermarket gears are not made to use the Dana factory set up tools, so a person usually has to apply some blood-boiling "Kentucky Windage" to the setup procedure to make progress.

tech note

You will often see the stock "fast" ratio called either 3.54 ratio or 3.55 ratio. Even Dana catalogs will list this gear set as a 3.54 in one catalog and 3.55 in the next. Actual tooth count is 39 ring gear teeth and 11 pinion gear teeth, which makes the true ratio 3.545, so technically 3.55 is correct once rounded to the nearest ratio. The 4.10 Ratio is a true 4.10 having 41 ring gear teeth and 10 pinion gear teeth. The higher the numeric ratio, the greater the gear reduction.

photo

QU40378 Dana 60 3.55 Ring and Pinion Set for Dodge Ram Dana 60 Is 100% genuine original equipment parts including: a 3.55:1 matched ring and pinion set, inner pinion bearing and cup, outer pinion bearing and cup, pinion slingers, pinion preload spacer (crush sleeve), pinion depth shims, differential shims, pinion seal, pinion nut, and ring gear bolts.  NOTE: Included pinion seal is for 1994-1999, see Catalog Page for 2000-2002 model year Pinion Seals. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40492 Dana 60 4.10 Front Ring and Pinion Set for 2000-2002 Dodge Ram Dana 60 Is 100% genuine original equipment parts including: a 4.10:1 matched ring and pinion set, inner pinion bearing and cup, outer pinion bearing and cup, pinion slingers, pinion preload spacer (crush sleeve), pinion depth shims, differential shims, pinion seal, pinion nut, and ring gear bolts. Order QU40271 Right Axle seal, QU40298 Left Axle Shaft Seal, and QU40184 Differential Bearing Set separately. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Seals and Seal Kits

top_page
product note

Your 2000, 2001, or 2002 3/4 ton Dodge Ram 2500 or 1 ton Dodge Ram 3500 Dana-Spicer Model 60 front axle has a total of six serviceable seals. Three are oil seals and 3 are dust seals. There is an oil seal for each axle shaft that keeps your differential gear lube from pouring out the ends of the axle housing tubes (see QU40271, QU40298). Each inner axle shaft also has a QK4629 Dust Seal installed inboard of the u-joint yoke to keep crud out of the tubes. For the pinion yoke, differential lube is kept where it belongs by QU40348 Oil Seal which in turn is protected from road debris by QU40397 V-Seal. The wheel seals are not available separately as these vehicles have sealed, unitized, non-serviceable hub assemblies.

photo

QU40348 2000-2002.5 Pinion Seal For early to mid production 2000-2002 Dana Model 60 Dodge Ram front axles. This seal installs flush with the front of the housing. A band of sealant on the back face of the seal shell will contact the inner face of the seal bore when the seal is fully seated in the axle housing. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40402 Dana 60 Flanged Design partial 2002 year Inner Pinion Seal For later production (mainly 2002) Dana Model 60 front axles in Dodge Ram 2500, Ram 3500 trucks. This seal fits late production housings with deep seal bores. This seal can be identified by an external flange that seats against the front face of the axle housing. A band of sealant is factory installed to seal against leaks between the seal and housing. This seal is used in conjunction with QU40397 V-Seal. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40397 Pinion Wiper V-Seal Is used on all 2000-2002 Dana Model 60 front axles to protect QU40348 Pinion Seal from road splash and grit. The flexible wiper lip is in constant contact with the steel flat front face of the pinion seal. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40271 Right Axle Shaft Seal is a genuine original equipment seal used for the Right Axle Seal on all 2000, 2001, and 2002 Dodge Ram 2500 and Ram 3500 4x4 trucks WITH the vacuum controlled Central Axle Disconnect (CAD) system. QU40271 IS NOT used on those later production 2002 models that did not have CAD. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40298 Left (All) or Right (2002 w/o CAD) Axle Shaft Seal for Ram 2500, Ram 3500 Dana 60 Front Axles A genuine original equipment seal used as the LEFT Axle Seal on all 2000, 2001, and 2002 Dodge Ram 2500 and Ram 3500 4x4 trucks with or without the vacuum controlled Central Axle Disconnect (CAD) system. QU40298 is also used as the RIGHT Axle Shaft Seal on those later production 2002 models that did not have CAD. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4621 Inner Axle Seal and Tool Kit Fits 2000 to early 2002 Dodge Ram 2500 and 3500 with the vacuum controlled Central Axle Disconnect (CAD). Installs QU40271 and QU40298 original equipment seals. These large diameter seals are not interchangeable with any other year or model of truck. CNC Precision Machined Installers to allow adjustment of seal depth to compensate for worn inner axles. QK4621 Kit includes QT1070 Right Axle Seal Installer, QT1071 Left Axle Seal Installer, QT1131 Axle Thrust Plate, QT1048 Pull Rod, with hardware, QU40090 CAD Gasket, 1 each QU40271, QU40298 Axle Shaft Seals, and QU50048 Vent Hose Clamp. More Info

Note: Optional TSB4620 can also be used for servicing the Axle Shaft Seals on 2000-2002.5 Dodge Ram 2500 and 3500 with CAD, but seals and seal tools will be different, plus these trucks use a different brake system.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TS4621 Inner Axle Oil Seal Tool Set Fits 2000 to early 2002 Dodge Ram 2500 and 3500 with the vacuum controlled Central Axle Disconnect (CAD). Installs QU40271 and QU40298 original equipment seals. These large diameter seals are not interchangeable with any other year or model of truck. CNC Precision Machined Installers to allow adjustment of seal depth to compensate for worn inner axles. TS4621 Kit includes QT1070 Right Axle Seal Installer, QT1071 Left Axle Seal Installer, QT1131 Axle Thrust Plate, and QT1048 Pull Rod with hardware. TS4803 similar except does not include QT1071 installer. More Info

Note: Optional TSB4620 can also be used for servicing the Axle Shaft Seals on 2000-2002.5 Dodge Ram 2500 and 3500 with CAD, but seals and seal tools will be different, plus these trucks use a different brake system.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4802 Inner Axle Oil Seal and Tool Kit To install both the left and right Inner Axle Shaft Seals for all mid to late 2002 model year Dodge Ram 2500 and Ram 3500 4x4 trucks WITHOUT Central Axle Disconnect (CAD). CNC Precision Machined Installers to allow adjustment of seal depth to compensate for worn inner axles. QK4802 Kit includes QT1071 Seal Installer, QT1130 Thrust Plate, QT1133 Press Screw with Hardware, and two QU40298 Inner Axle Shaft Seals. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TS4802 Inner Axle Oil Seal Tool Set To install both the left and right Inner Axle Shaft Seals for all mid to late 2002 model year Dodge Ram 2500 and Ram 3500 4x4 trucks WITHOUT Central Axle Disconnect (CAD). CNC Precision Machined Installers to allow adjustment of seal depth to compensate for worn inner axles. TS4802 Kit includes QT1071 Seal Installer, QT1130 Thrust Plate, QT1133 Press Screw with Hardware. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4629 Outboard Axle Dust Seal Set These Seals are installed on your inner axle shafts right next to the u-joint yoke. When the axle shaft is installed, the face of the seal will seal against the end of the axle tube to keep dirt, dust, and crud from entering the axle housing tubes. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
photo

QU10594 Hub-to-Knuckle Bolt For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU10594 Hub-to-Knuckle Bolt also fits all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40022 Pinion Nut For all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU40022 Pinion Nut also fits all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. This is a genuine original equipment, self-locking nut intended for a single use part. Discard and replace with a new nut any time you remove the pinion nut. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40023 Pinion Washer for Dodge Ram Is a genuine original equipment flat washer goes between the pinion nut and pinion yoke. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40343 Hardened Differential Cap Retaining Bolt Genuine original equipment hex-head bolt for Dana 60 front axles for all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks. QU40343 Differential Cap Retaining Bolt also fits all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40356 Pinion Preload Spacer (Crush Sleeve) for Dodge Ram Genuine original equipment spacer is is critical for setting your pinion rotating torque. Designed as a use once and throw away part. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40365 Pinion Depth Shim Kit Is a genuine original equipment Kit. Also included in TK4843. More Info

 

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40206 Differential Bearing Shim Kit Includes a selection of genuine original equipment Shims for adjusting backlash and differential bearing preload. Also included in TK4843. More Info

 

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40095 Outer Pinion Slinger Fits between the outer Pinion Bearing and Pinion Yoke. Also included in TK4837 and TK4843. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40086 Ring Gear Bolt For Dana 60 or Dana 70. Genuine Dana-Spicer Grade 9 Bolt has locking teeth under the hex head to prevent loosening under any load conditions. Also included in TK4843. More Info

Dan the Gear Man® Safety Note: Ring Gear Bolts are designed for a single use. They must be replaced after they are removed!

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Tie Rods

top_page
product note

At this time we do not stock any tie rod assemblies. However, we do stock new self-locking nuts for the factory tie rod and drag link.

photo

QU10602 Self Locking Tie Rod or Drag Link Nut For safety reasons, you MUST replace the nonreusable, self-locking factory nuts securing the tie rod and drag link ends. This type of nut was designed as a single use item and it may fail if reused. So anytime you disconnect a factory Dodge tie rod or drag link end such as when doing Ball Joint service, replace the old part with one of these new genuine original equipment nuts and then tighten it using the procedure spelled out in the Dodge Factory Shop Manual. We include two of these nuts with our QK4510 series Ball Joint Kits. There are a total of four QU10602 nuts on you Ram pickup, two for the drag link and 2 for the tie rod. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU11209U Used Right Front Steering Knuckle for 2000-2002 Dodge Ram 2500, and Ram 3500 Dana 60 Front Axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU11210U Used Left Front Steering Knuckle for 2000-2002 Dodge Ram 2500, and Ram 3500 Dana 60 Front Axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 60 front axle in your 2000-2002 Dodge Ram 4x4.

photo

QT1070 Right Side Inner Axle Seal Installer More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1071 Left Side Inner Axle Seal Installer More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1131 Axle End Plate for Installing Inner Axle Seals More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1048 18" Pull Rod Is a 150,000 psi tensile strength threaded rod used in conjunction with the inner axle seal installers and thrust plate. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1130 Inner Axle Seal Installer Thrust Plate Fits all Dana Model 60, Super 60 axles from 1967-current. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1133 Press Screw Assembly For installing QU40059 Inner Axle Seals in Dana Model 60 and 61 front drive axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1145 Driver Handle Is used in conjunction with QT1216 Seal Remover to drive the inner axle seals out of the axle housing bores on all 2000-2002 Dodge Ram 2500 and Ram 3500 4x4 front axles that equipped with the vacuum controlled CAD system. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1216 Seal Remover Is used with QT1145 Driver Handle to drive the inner axle seals out of the axle housing bores on all 2000-2002 Dodge Ram 2500 and Ram 3500 4x4 front axles equipped with the vacuum controlled CAD system. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TS4862 Inner Axle Seal Remover Set Is used to drive the inner axle seals out of the axle housing bores on all 2002 Dodge Ram 2500 and Ram 3500 4x4 front axles that are not equipped with the vacuum controlled CAD system. Set includes QT1145 Driver Handle, QT1151 Extension Rod, and QT1214 Seal Remover. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TS1065 Ball Joint Press Set Easily removes and installs the Ball Joints on all 2000 to 2002 Dodge Ram 2500 and Dodge Ram 3500 4x4 trucks. Specifically designed to make the task of changing the ball joints on your 2000-2002 Dodge RAM truck easy and safe! Long throat design will handle the job! (Unlike standard, short throat presses offered by others.) This pro-quality Press Set includes cast iron long reach ball joint press, 2 receivers, one installer, and press stub. Optional tooling is available for other applications. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1032 Case Spreader Is used to relieve the differential bearing preload making it easy to safely remove and install your front differential without damaging expensive critical parts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1072 Hub Puller Is used to remove the front wheel hubs for all 2000 Dodge Ram 2500, 2001 Dodge Ram 2500, and 2002 Dodge Ram 2500 4x4 trucks, and all 2000 Dodge Ram 3500, 2001 Dodge Ram 3500, and 2002 Dodge Ram 3500 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1200 Tie Rod Separator Allows you to remove the separate tie rod and drag link ends without wrecking the seals or screwing up your steering linkage ends. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1008i Axle Shaft Nut Socket 1/2" drive impact socket fits the odd-ball sized nuts (QU40114) threaded on the ends of your outer axle shafts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1103 Driver Is used in conjunction with QT1027 and a hammer to drive your wheel hub assembly from the steering knuckle. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT9404 Application Brush For Anti-Seize or Gear Marking Compound. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT2005 Inner Pinion Bearing Installer Is used to quickly and easily seat your QU50407 Inner Pinion Bearing on the pinion. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1805 Inner Pinion Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50406 Inner Pinion Bearing Cup a simple and fast procedure. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1812 Outer Pinion Bearing Cup Installer Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50400 Outer Pinion Bearing Cup a simple and fast procedure. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1088 Differential Step Plate Fits either side of the differential and is used to support the differential when installing your differential bearings or it acts as a push plate when you use a puller to remove the old bearings. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1158 Differential Bearing Installer Makes a hard job easy. The raised inside ridge matches against inner differential bearing race allowing you to easily press or drive on QU50398 differential bearing until the bearing is fully seated against the differential adjusting shims. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1100 8" Standard Duty Installer Driver Handle with knurled hand grip are used with QT1500 series Seal Installers and QT1800 series Bearing Cup Installers with 5/8" center holes. 1" diameter x 8" usable length for general purpose use. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT9206 Torx® Socket For QU10612 Caliper Bolts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT9308i Multi-Piece Slide Hammer Puller Set with storage case. Includes slide hammer with multiple attachments including 2/3 jaw, internal and external pullers, rear axle puller, locking pliers adaptor, puller hook, and dent puller. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Discontinued Tools

top_page
photo

QT9018 5 Pound Dead Blow Hammer Is just about the first tool you will reach for a multitude of jobs on your Dodge Ram. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool. Discontinued.

photo

QT1098 Differential Master Bearings Slip on your differential in place of the taper bearings and cups. Used along with a dial indicator to determine the correct differential shim thickness. Discontinued.

photo

QT1027 Impact Socket 1/2" drive socket for removing the 12 point QU10614 hub to knuckle bolts. Discontinued.

photo

QT9302 5 Pound Slide Hammer A first-class tool for pulling just about anything you can get a matching 5/8" fine thread puller for. Superseded to QT9308i.

Montana Life

top_page
photo

Crow Lake in Montana's Beartooth Mountains.