Parts for Open Knuckle Dana-Spicer Model 44 Front Axles in 1966-1979 Ford F-100, F-150, Bronco 4x4s

We stock a good selection of parts and tools for Dana 44 open knuckle front drive axles for 1966 to 1979 Ford F-100, F-150, and 1971 to 1979 Ford Broncos. Although all axles for these years Ford Bronco and 1/2 ton trucks are of the open knuckle type (axle u-joint is exposed), there was a very significant Steering Knuckle design change between 1971 to 1972 for the trucks and 1972 to 1973 for the Bronco. The early Knuckles used King Pins and King Pin Bearings to support the Knuckle, while the later trucks use Ball Joints.

Axle Identification

top_page
photo

Cover: 10 Bolt, 10-3/8" high

Suspension: Coil spring

Ball Joints: Pressed in Steering Knuckle, nuts at top

Axle Shafts

top_page
product note

From 1966 through 1972 Ford F100 1/2 ton axle shafts used Spicer 1310WJ series axle universal joints with 1-1/16" diameter cups. Starting in the 1973 model year, Ford beefed up the axle shaft u-joint for the F100 to the more durable Spicer 1350WJ size which has 1-3/16" diameter cups. Broncos still used the smaller 1310WJ series axle shafts through 1977. 1978 and 1979 Broncos use the same 1350WJ series axle shafts as the F100 and F150.

QU40158 Outer Axle Shaft for 1973-1979 F100, F150, and 1978-1979 Bronco With Dana 44 Front Axles is a genuine Dana part for either side side of your vintage Ford Dana 44 open knuckle front axle. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40672 Right Inner Axle Shaft for 1973-1979 F100, F150, and 1978-1979 Bronco With Dana 44 Front Axles is a genuine Dana part for the passenger side of your vintage Ford Dana 44 open knuckle front axle. More Info
Also available while supplies last: QU40672U Used Axle Shaft

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40673 Left Inner Axle Shaft for 1973-1979 F100, F150, and 1978-1979 Bronco With Dana 44 Front Axles is a genuine Dana part for the driver's side of your vintage Ford Dana 44 open knuckle front axle. More Info
Also available while supplies last: QU40673U Used Left Axle Shaft

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Seals and Seal Kits for Inner Axle Shafts

top_page
photo

QU40055 2-9/32" OD Inner Axle Shaft Seal for 1966 to 1977 Is a genuine Dana replacement Seal for 1971-1977 Bronco, plus 1966-1977 F100 and F150 with the open knuckle Dana 44 front axle. QU40055 is a unitized seal that combines an axle shaft guide and inner axle shaft seal in one part. QU40055 replaces both the separate seal and guide used on 1966-1971 axles and the one piece seal in 1972-1977 axles. One of these Seals are installed in each axle tube, right next to the differential to keep gear lube from leaking out the ends of the axle housing. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40159 2-9/32" OD Inner Axle Shaft Seal for most 1978-1979 F150 Super Cab 4x4s with the open knuckle Dana 44 front axle. One of these Seals are installed in each axle tube, right next to the differential to keep gear lube from leaking out the ends of the axle housing. QU40105 fits 1978-1979 Ford F150 Super Cab with axle tag numbers: 610048 or 610068. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40160 2-5/8" OD Inner Axle Shaft Seal For most 1978-1979 Ford Bronco and F150 4x4s with the open knuckle Dana 44 front axle. One of these Seals are installed in each axle tube, right next to the differential to keep gear lube from leaking out the ends of the axle housing. QU40160 fits 1978-1979 Ford Bronco and F150 with axle tag numbers: 610019, 610020, 610047, 610049, 610066, or 610067. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4933 Front Inner Axle Seal and Install Tool Kit for Dana 44 axles with QU40160 2-5/8" Outside Diameter axle shaft seals. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Seals and Seal Kits for Outer Axle Shafts

top_page
product note

All 1966-1979 Ford 4x4 models with Dana 44 front axles have Inner Axle Shaft Oil Seals pressed in the inboard end of each axle tube, right next to the differential side bearings. These seals contact the inner axle shafts to prevent gear oil from running out of the differential and down the axle tubes. Old age, blown axle u-joints, and/or grit that works it's way into the axle tubes and cuts the seal are the usual causes of failure. A bad Inner Axle Shaft Seal can be detected by oil coming out the end of the axle tubes next to the axle shaft u-joint. Usually when these Seals start to fail, they will seep oil so the leakage may go undetected for quite some time. Many a ring and pinion set has been burned up from axles that lost all their lube when long term seepage was not noticed. Different Seals were used depending upon year and axle tag number. Axle disassembly including differential removal is required to replace the Inner Axle Shaft Seals.

photo

QK4872 1966-1977 Ford Dana 44 Axle Seal Tool Kit Quickly and easily installs QU40055 Inner Axle Seals to a precise depth in 1966-1977 Ford F-100 1/2 ton 4x4s and 1971-1977 Ford Bronco standard Dana 44 closed knuckle front axles. Our unique installer design will press in new your Inner Axle Seals without damage because the CNC Precision Machined Installation Tool cups the seal so force is only applied on the steel seal shell. QK4872 Kit includes install tools and two seals. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4830 1978-1979 Ford F150 Super Cab Dana 44 Axle Seal Kit with Adjustable Depth Axle Seal Tool Set Quickly and easily installs QU40159 Inner Axle Seals in 1978-1979 F150 Super Cab Dana 44 Front Drive Axles with axle tag numbers 610048 or 610068. Our unique installer design allows you press in new your Inner Axle Seals to a different depth to miss a groove worn in your axle shaft by the old seal. New Seal is installed without damage because the CNC Precision Machined Installation Tool cups the seal so force is only applied on the steel seal shell. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note

Ford increased the axle u-joint size from small to medium on F-100/F-150 Dana 44 axles for the 1973 model year, however the Bronco continued to use the smaller u-joints through the 1977 model year. The new body style Bronco, introduced as a 1978 model, is based on the F-150, so it also has medium size axle u-joints. Before ordering axle u-joints for transition year models, verify the diameter of the axle universal joint cups!
1966-1972 F- 100 and 1971-1977 Bronco: Axle U-Joint Cup Size is 1-1/16".
1973-1979 F-100/F-150 and 1978-1979 Bronco: Axle U-Joint Cup Size is 1-3/16"
For the early, small 1-1/16" u-joint we have only one non-greaseable choice as the small cross will lose too much strength if drilled for lube channels. We offer two different medium size 1-3/16" Universal Joints. Both are good, reliable products, but different manufacturing techniques and seal types will have a major influence on the ultimate life of the joint under most conditions.

photo

QU90007 1973-1979 Greaseable Axle U-Joint with Rubber Seals for Ford F-100, F-150 and 1978-1979 Bronco Dana 44 Front Axles Value priced with Hot-Forged cross and flexible rubber seals. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40712 1973-1979 Premium Torque King® Cold-Forged Non-Greaseable Medium Axle U-Joint for Ford F-100, F-150 and 1978-1979 Bronco Dana 44 Front Axles Is a premium, quality factory lubed, 1-3/16" cup diameter universal joint for your heavy-duty 4x4. TK40712 is our best selling u-joint for this application because it combines the strength of a solid, cold-forged cross with excellent seals and a maintenance free, factory-lubed design that meets or exceeds all original equipment specifications. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40792 1966-1972 Ford F-150 and 1971-1977 Bronco Dana 44 Small Front Axle Shaft U-Joint Is a hot-forged, original equipment, non-greaseable, front axle shaft universal joint with 1-1/16" diameter cups. This is the strongest production u-joint we know of for this application. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40822 1966-1972 Greaseable Axle U-Joint with 1-1/16" cups for 1966-1972 F100 and 1971-1972 Ford Bronco Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ball Joints 1972-1979 F-100 F150, & 1973-1979 Bronco (See King Pins for 1966-1971 F-100 and 1971-1972 Bronco)

top_page
product note

The 1972-1979 Ford Dana 44 Beam Type open knuckle front axle uses replaceable Ball Joints pressed into the steering knuckle. Both Ball Joints are weight bearing. A threaded adjuster that screws into the upper hole of the axle yoke is used to provide preload on the Ball Joints. Dana has modified the seal configuration, but the high quality and basic Ball Joint design has remained unchanged since the early 1970's. Over the years we have found the average Ball Joint life of our non-greaseable, factory Dana Ball Joints to be 7 to 10 years for vehicles used as daily drivers and/or work trucks.

photo

QU40187 Original Equipment Ball Joint Set for Ford Dana 44 Front Axles Are current production Dana original equipment, factory lubed, Upper and Lower Ball Joints with hardware for 1972-1979 Ford F-100/F-150 4x4 trucks and 1973-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
photo

QU80002 Caliper Slide Lock Bolt Is a special, hex head bolt that threads into the caliper anchor plate on your disc brake equipped 1975-1979 Ford F100/F150 4x4 truck and 1976 to 1979 Ford Bronco. The tapered body between the threads and end fits into the inner notch of the caliper slide or key. QU80002 is plated for corrosion resistance. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings (Individual)

top_page
product note

All 1966 to 1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with open knuckle Dana 44 Front Axles use the same differential and pinion bearings.
All bearings are not created equal for fit or durability, so we only stock first class, long lasting, Timken® Differential and Pinion Bearings for your Dana front axle. Timken® was and is a a major original equipment supplier of top-notch bearing components to Dana Spicer. Since I first started rebuilding Dana axles in the mid 1970's, I have found Timken® Bearings to be the most consistent in relation to the published dimensions of any bearing on the market which makes rebuilding an axle right the first time a WHOLE lot easier!

photo

QU50533 Timken® Outer Pinion Bearing Cup For 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. This is a First Class, original equipment quality bearing cup that meets or exceeds all vehicle manufacturer specifications making it the top choice for heavy-duty applications like yours. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50534 Timken® Outer Pinion Bearing For 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. This is a First Class, original equipment quality bearing cup that meets or exceeds all vehicle manufacturer specifications making it the top choice for heavy-duty applications like yours. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50535 Timken® Inner Pinion Bearing Cup For 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. This is a First Class, original equipment quality bearing cup that meets or exceeds all vehicle manufacturer specifications making it the top choice for heavy-duty applications like yours. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50536 Timken® Inner Pinion Bearing For 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. This is a First Class, original equipment quality bearing cup that meets or exceeds all vehicle manufacturer specifications making it the top choice for heavy-duty applications like yours. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50538 Timken® Differential Side Bearing For 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. (uses 2). This is a First Class, original equipment quality bearing cup that meets or exceeds all vehicle manufacturer specifications making it the top choice for heavy-duty applications like yours. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50537 Timken® Differential Side Bearing Cup For 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. (uses 2). This is a First Class, original equipment quality bearing cup that meets or exceeds all vehicle manufacturer specifications making it the top choice for heavy-duty applications like yours. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing and Seal Kits

top_page
product note

Most remaining 1966-1979 Ford F100, F150 and 1971-1979 Broncos with open knuckle Dana 44 Front Axles use part time transfer cases and have lockout hubs. With a part time transfer case and lockout hubs, the axle shafts and differential parts do not rotate, so extreme diff/pinion bearing wear is rather rare except in work trucks. However, the flip side is water condensation in the diff has a tendency to cause rust and pitting of the bearings. If your vintage Ford has been used a lot in 4x4 mode or parked outside and subject to temperature changes, there is a good chance that significant wear or water damage may have occurred on your differential and pinion bearings. When you replace the bearings, do not forget to replace the inner axle shaft oil seals.

photo

QU50576 Differential Bearing and Seal Kit For 1966-1979 F100/F150 and 1971-1979 Broncos with the Dana 44 open knuckle front axle features first class Timken® Differential and Pinion Bearings, plus Pinion Seal, Pinion Nut, Crush Sleeve, Gear Marking Compound, Threadlocker, and RTV Sealant. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
product note

Most 1966-1979 Ford F100/F150/Bronco Dana 44 Front Axles were factory equipped with conventional open differentials. An optional Powr-Lok (1968-1972) or Trac-Lok® (1973-1979) limited slip differential was also offered. Depending upon the year, both full time and part time transfer cases were used to drive the front axle. In vehicles having full time transfer cases in which the front axle is always under power when driving, wear on the thrust washers and cross shaft can be expected on higher mileage vehicles. The differential small parts are the same for all ratios, but the ring gear flange on the case castings are different for 3.73 and numerically lower ratios and axles having 4.09 and numerically higher ratios due to the pinion gear diameter size for high and low ratios.

photo

QU40000 Dana 44 Pinion Mate Thrust Washer Is a genuine Dana hardened concave thrust washer that fits between each of the small diameter pinion mate gears in your 1966-1979 Ford F-100/F-150 4x4 truck or 1971-1979 Ford Bronco Dana 44 open differential. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40033 Dana 44 Side Gear Thrust Washer Is a genuine Dana hardened flat thrust washer that fits between each of the splined differential side gears in your 1966-1979 Ford F-100/F-150 4x4 truck or 1971-1979 Ford Bronco Dana 44 open differential. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40001 Dana 44 Differential Cross Shaft Retaining Pin Is a genuine Dana spring steel Pin used to retain your differential cross shaft in the diff case for 1966-1979 Ford F-100/F-150 4x4 trucks or 1971-1979 Ford Broncos with open front differentials. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40003 Dana 44 Differential Cross Shaft Is a genuine Dana hardened steel shaft that acts as the axle for the two small pinion mate gears for all 1966-1979 Ford F-100/F-150 4x4 trucks or 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40178 30 Spline Dana 44 "Spider Gear" Kit Is a genuine Dana Inner Differential Parts Kit for open differentials in Dana 44 axles with 30 spline inner axle shafts. QU40178 fits 1966-1979 Ford F-100/F-150 4x4 trucks or 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Makers

top_page
product note

In the mid 1970's Dana made a differential cover design change to heavy gauge covers with flat mating flanges. Unlike the previous, thin gauge covers with embossed flanges which were made for use with a cut gasket, the new design, thick gauge covers are designed for sealing with RTV. If you desire, you can still use a gasket with the new type cover by combining the gasket with thin films of RTV. We stock both Ultra Gray RTV Sealant and genuine Dana Gaskets.

photo

QU40214 Dana 44 Cover Gasket Is a genuine original equipment Dana Gasket for all Dana-Spicer Model 44 axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hubs and Hub Parts

top_page
product note

Drum brakes were used by Ford on the Dana 44 up to 1975. 1976 to 1979 4x4s all have front disc brakes. The wheel hubs are not interchangeable between disc and drum brakes. Most 1966-1973 era Ford 4x4s were delivered with lockout hubs as are all the 1974-1979 vehicles with part time transfer cases. Solid, splined hub gears were used on bone stock 1966-1973 models and all 1974-1979 units with the NP203 full time transfer case. Over the years, just about all the splined hub drive gears have been replaced with lockout hubs.

photo

QU20371U Used Wheel Hub for 1966-1969.5 Ford F100 4x4 trucks is a serviceable used front wheel hub with good bearing and seal bores for Dana 44 closed knuckle front axles. Fits 1966-1969 F100 trucks up to serial number F70000. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20392U Used Wheel Hub for 1969.5-1975 Ford Bronco and F100 4x4 trucks is a serviceable used front wheel hub with good bearing and seal bores for Dana 44 closed knuckle front axles. Fits 1969.5-1975 F100 trucks from 1969 serial number F70001 and 1972-1975 Dana 44 equipped Ford Broncos from 1969 serial number F30001. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20348 1976-1979 F100, F150, Bronco Splined Front Hub Is a brand new internally splined front wheel hub with studs that fits all 1976-1979 Ford F100, F150 and full size Bronco 4x4s with disc brakes. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU51181 Warn 20990 Premium Hub Set for Dana 44 Front Axles With internally splined front wheel hubs. Reliable and good looking. QU51181 Fits most Ford Dana 44 1970-1979.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56018 Warn Manual Hub Set Is a reliable, original equipment quality hub set with installation hardware for all part time transfer case equipped 1966-1979 Ford Bronco, F100, and F150 4x4s with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56019 1 Side Warn Manual Hub Set More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4918 Hub Service Kit For QU56018 Warn Manual Hub Set. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40044 Hub Dial O-Ring For Dana original equipment, plastic dial, spline mount factory hubs used on 1970 to 1979 Ford F-100, F-150 and 1978-1979 Ford Bronco Dana 44 front axles with internally splined wheel hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40699 Large Hub Plate to Wheel Hub Internal Snap Ring For Dana original equipment, plastic dial, spline mount factory hubs used on 1970 to 1979 Ford F-100, F-150 and 1978-1979 Ford Bronco Dana 44 front axles with internally splined wheel hubs.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40032 Axle Shaft Snap Ring Is a genuine original equipment part for 1970 to 1979 Ford F-100, F-150 and 1978-1979 Ford Bronco Dana 44 front axles with internally splined wheel hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40154 Hub Cam Body for Spicer Plastic Dial Internal Mount Hubs Is a new old stock (NOS) genuine Spicer replacement part for original equipment Spicer Lockout Hubs used on 1970 to 1979 Ford F-100, F-150 and 1978-1979 Ford Bronco Dana 44 front axles with internally splined wheel hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40050 Spicer Tapered Hub Spring For Spicer Plastic Dial factory hub-locks or full time drive gears. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40035 Hub Spring Plate Fits between the QU40050 hub spring and the outer wheel bearing cup on 1970 to 1979 Ford F-100, F-150 and 1978-1979 Ford Bronco Dana 44 front axles with internally splined wheel hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40558R Reconditioned 10 Tooth Axle Shaft Gear for Spicer Plastic Dial Hubs These are good used reconditioned gears with a Black Oxide coating for corrosion protection. This is the later design, coarse tooth gear used in in the 1978-1979 Ford Dana 44. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40559R Reconditioned 10 Tooth Hub Drive Gear for Spicer Plastic Dial Hubs These are good used reconditioned gears with a Black Oxide coating for corrosion protection. This is the later design, coarse tooth gear used in in the 1978-1979 Ford Dana 44. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40427 Dana 44 Full Time Front End Hub Cap Is a genuine Dana replacement part for 1973-1981 GM Dana 44 front axles. These chromed steel Caps are the redesigned cap that was introduced around 1980 and it is the recommended replacement for the 1973-1979 cap that was made from a little heavier gauge of steel. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40598 1-1/4" Wide Stepped Gear was the original design. Outside spline that engages wheel hub is 27/32" wide. These gears are stepped on the outboard side to aid in removal and to space the gear back from the hub cap. QU40598 gears were usually used with QU40050 Spring and QU40035 Spring Plate. The back edge of the snap ring groove is approximately 5/16" from the end.

Also available while supplies last: QU40598U Used 1-1/4" Wide Stepped Gear

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40428U Used 7/8" Wide Single Width Gear Has full length ID and OD splines. These gears have 2 to 10 holes in them to reduce the weight and provide a way to remove them with a hook. QU40428 gears were generally used with QU40050 Spring and QU40035 Spring Plate in the 1970s or QU40654 1-1/4" long Split Steel Steel Spacer in the 1980s and 1990s. To use this gear, your axle shaft has to have the back edge of a snap ring groove located about 5/8" from the end.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40657U Used 7/8" Wide Stepped Gear was the most common type from the the late 1970's to the late 1980s. Outside spline that engages wheel hub is a little under 5/8" wide. These gears are stepped on the outboard side to aid in removal and to space the gear back from the hub cap. QU40657 gears were usually used with QU40050 Spring and QU40035 Spring Plate in the 1970s or QU40654 1-1/4" long Split Steel Steel Spacer in the 1980s and 1990s.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40566R Reconditioned Hub Plate for Spicer Plastic Dial Hubs is a good used Cam Plate with a Black Oxide coating for corrosion protection. Fits factory Spicer lockout hubs used on Dana 44 and GM 10 Bolt front axles with internally splined wheel hubs until 1981.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40694U Weathered but Usable Used Red Plastic Hub Dial for 1968-1979 Ford Dana 44 front axles with Spicer factory lockout hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20389U One Functional Used Dana Factory Lockout Hub and Red Dial fits 1970-1979 Ford F100, F150 with Dana 44 front axles with splined wheel hubs. Complete except for QU40035 Spring Plate which must be ordered separately. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

King Pin Parts 1966-1971 F-100 (See Ball Joints for Later Years)

top_page
product note

1967-1971 Ford F100 Dana 44 Front Axles use an unusual open knuckle design the uses King Pins and Knuckle Bearings like a closed knuckle axle instead of Ball Joints. Once installed, there is no way to lubricate the Knuckle Bearings without disassembly so it is imperative that you pack your new Bearings with a high quality grease such as Pyroplex Plus® before installation. Knuckle Bearing preload is set using a combination of shims located between the King Pin Caps and Steering Knuckles. On 1968-1971 axles, compressible dampeners positioned between the inner Cup Plug and King Pin Stem are used to control "Death Wobble" (These dampeners also affect the Knuckle turning preload).

photo

QU20096 King Pin Dampener and Seal Plate Kit Is a genuine Dana original equipment Kit for 1966-1971 Ford F100 with Dana 44 open knuckle front axle. QU20096 fits under a King Pin and is designed to dampen shocks to eliminate "Death Wobble". More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20231 King Pin Seal For 1966-1971 Ford F100 with Dana 44 open knuckle front axle. QU20231 fits over the Knuckle Bearing and it seals on the King Pin Stem. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4617 Ford F-100 Dana 44 Open Knuckle Front Axle Knuckle Bearing Kit Includes 4 Timken® Knuckle Bearings, 4 Timken® Knuckle Bearing Cups, and Rectangular Knuckle Shim Set to service both sides of your vintage 1966-1971 Ford F100 with Dana 44 open knuckle front axle. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40773 Knuckle Shim Kit for 1966-1971 Ford F-100 Dana 44 Open Knuckle Front Axles Includes a selection of rectangular shims to adjust the Knuckle Bearing preload. Services one side of your vintage 1966-1971 Ford F100 with Dana 44 open knuckle front axle. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20091 Trapezoid Knuckle Shims For 1966-1971 Ford F100 with Dana 44 open knuckle front axle. fit between the combination steering arm/upper king pin to adjust the turning preload for the Drivers Side Steering Knuckle on your vintage Ford F100. 0.005" Shim. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50627 Ford F-100 Dana 44 Open Knuckle Timken® Knuckle Bearing Cup For 1966-1971 Ford F100 with Dana 44 open knuckle front axle. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50628 Ford F-100 Dana 44 Open Knuckle Timken® Knuckle Bearing For 1966-1971 Ford F100 with Dana 44 open knuckle front axle. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals and Technical Information

top_page
product note

Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations.

photo

TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles Covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts

top_page
product note

Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings.

photo

S24200 Blue Threadlocker For spindle and ring gear bolts etc. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S9975 Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90018 Pyroplex® Protection ES Synthetic Grease Provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions! More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90016 SynPower® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90015 High Performance Synthetic Arctic Grease Is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90017 Red Grease Is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. cartridge or 1 pound tub. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals and Pinion Yokes

top_page
photo

QU40215 Dana 44 Front Axle Pinion Seal Is a genuine original equipment pinion seal for all 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40848 26 Spline 1330 Series Pinion Yoke For both full time and part time Ford Bronco and F150 Dana 44 front axles . U-Joint width is 3-5/8". More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40849 1310 Series U-Bolt Style Pinion Yoke Is an OE type 26 spline Yoke for both full and part time full time Ford Bronco and F100/F150 Dana 44 Front Axles. U-Joint width is 3-7/32". More Info
Also see QU40734 Strap and Bolt style Yoke

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40905 Driveshaft U-Bolt Kit for 1350 and 1410 Series U-Joints fits many vintage axle, transfer case, and transmission yokes from the mid 1940's to the mid 1980's on Chevy, Ford, and GMC 4x2 and 4x4 vehicles up to 1-1/2 ton size used u-bolt style yokes for Spicer series 1350 or 1410 series universal joints. This u-bolt kit fits a great many of those yokes. Use this Kit to replace broken or stripped original u-bolts.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20390U Used 1330 Series 26 Spline U-Bolt Style Pinion End Yoke for 1979 and prior Ford Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
product note

The ring and pinion gear sets used in 1966-1979 Ford F100/F150 and 1978-1979 Bronco Dana 44 front axles have a reverse cut or spiral compared to the conventional Dana 44 gear sets found in 1971-1977 Broncos. The engineering reason for this is the pinion gear in 1966-1979 F100/F150 Ford Dana 44 axles is located above the axle center line. Reverse Spiral Gear Sets are NOT interchangeable with standard Dana 44 gear sets.

QU42013 4.09 Ratio Ford Dana 44 Reverse Spiral Ring and Pinion Kit is a genuine Dana Gear Set for Ford high pinion Dana 44 front axles in 1978-1979 Broncos and 1966-1979 F100, F150 4x4s. QU42013 includes a matched, reverse cut Dana ring and pinion set, pinion bearings with cups, pinion seal, pinion nut, pinion washer, pinion slingers, pinion shims, differential shims, and ring gear bolts. More Info

Also available while supplies last: QU42012U Used 4.09 Ratio Reverse Spiral Ring and Pinion Gear Set

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU42086U Used 3.50 Ratio Reverse Spiral Ring and Pinion Set for 1966-1996 Ford Dana 44 and Dana 44IFS front axles with pinions located above the axle centerline.  Pinion stem has 26 splines.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note

Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else.

photo

QU40209 Dana 44 Ring Gear Bolt For Dana 44 Axles. Genuine Dana-Spicer Grade 9 Bolt has locking teeth under the hex head to prevent loosening under any load conditions. More Info

Dan the Gear Man® Safety Note: Ring Gear Bolts are designed for a single use. They must be replaced after they are removed!

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40343 Dana 44 Hardened Differential Cap Retaining Bolt Genuine original equipment hex-head bolt for Dana Spicer Model 44 front axle differential bearing caps fits all 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40028 Dana 44 Inner Pinion Bearing Slinger Is a genuine Dana original equipment Oil Slinger. QU40028 fits between your Dana 44 axle's inner pinion bearing and pinion head. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40448 Dana 44 Inner Pinion Bearing Oil Baffle Is a genuine Dana original equipment stepped, stamped steel Oil Baffle. QU40448 fits between your Dana 44 axle's inner pinion bearing cup and the axle housing on 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40002 Outer Pinion Bearing Slinger QU40002 is a genuine Dana-Spicer part that fits between the outer pinion bearing and pinion yoke on 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40311 Dana 44 Front Differential and Pinion Shim Kit For 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. Genuine Dana-Spicer Shim Kit includes pinion depth shims, pinion preload shims, differential adjusting shims, pinion nut, pinion washer, and differential cover pan gasket. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40009 Dana 44 Axle Pinion Lock Nut Is a genuine Dana-Spicer original equipment replacement locking nut that fits 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40010 Dana 44 Axle Pinion Washer Is a genuine Dana-Spicer flat washer that fits between the pinion nut and pinion yoke on 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindles and Spindle Nuts

top_page
product note

All 1966-1979 Ford Dana 44 front axles had round, four slot spindle nuts from the factory. These parts can typically be reused, but you MUST always check the pin in the Inner Nut. IF the pin is damaged or broken, REPLACE THE NUT!!!

photo

QU40630 1966-1972 Ford Dana 44 Front Spindle Kit Is a new replacement Front Axle Wheel Bearing Spindle with factory installed spindle bearing and seal for drum brake equipped Dana 44 front drive axles in 1966-1972 Ford F-100 and Bronco 4x4s. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40004 Inner Spindle Nut For 1966-1979 Ford Bronco, F-100, F-150 Dana 44 Front Axles. threads on the spindle and fits against your outer wheel bearing to provide correct wheel bearing end-play. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40060 Spindle Lock Washer For 1966-1979 Ford Bronco, F-100, F-150 Dana 44 Front Axles. Locks your QU40004 Inner Spindle Nut in position when properly installed. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40031 Outer Spindle Nut For 1966-1979 Ford Bronco, F-100, F-150 Dana 44 Front Axles is tightened against your QU40060 Spindle Lock Washer to keep it in place and it acts as a jam nut effectively locking both spindle nuts and the washer together. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4727 Spindle Nut Kit For 1966-1979 Ford Bronco, F-100, F-150 Dana 44. includes one each of QU40004 Inner Spindle Nut, QU40060 Spindle Lock Washer, and QU40031 Outer Spindle Nut. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU42007 1973-1975 Ford Dana 44 Front Spindle Kit Is a brand new Front Axle Wheel Bearing Spindle with spindle seal, spindle thrust washer, and spindle bearing for drum brake equipped Dana 44 front drive axles in 1973-1975 Ford F-100 and Bronco 4x4s. QU42007 is a genuine Dana factory part.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Y442007 1973-1975 Ford Dana 44 Front Spindle Kit Is a brand new Front Axle Wheel Bearing Spindle with spindle seal, spindle thrust washer, and spindle bearing for drum brake equipped Dana 44 front drive axles in 1973-1975 Ford F-100 and Bronco 4x4s. Y442007 is a high quality replacement.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40192 1976-1979 Ford Dana 44 Front Spindle Kit is a Front Axle Wheel Bearing Spindle for disc brake equipped Dana 44 front drive axles in 1976-1979 Ford F-100, F-150 trucks and 1976-1979 Ford Bronco. More Info
QU40192U Used Spindle also available while supplies last.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Y440192 1976-1979 Ford Dana 44 Front Spindle Kit is a Front Axle Wheel Bearing Spindle for disc brake equipped Dana 44 front drive axles in 1976-1979 Ford F-100, F-150 trucks and 1976-1979 Ford Bronco. Y440192 is a high-quality replacement.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Bearings and Seals

top_page
product note

Ford used a single, 2" ID metal shell Spindle Seal up to 1972. These axles also have a bronze outer axle shaft thrust washer. For most 1973 and newer axles, these parts were replaced by a larger diameter single rubber V-Seal and a plastic trust washer, however Ford does catalog a 2" ID Rubber V-Seal for some 1973-1976 axles. In 1974, an additional V-Seal was added next to the spindle bearing on most axles. To accommodate the new part, the spindle had to be bored a bit deeper so the spindle bearing could be installed to a slightly greater depth. The 1974 design was used on all subsequent Ford Dana 44 axles through 1979.

photo

QU40043 Early Type Dana Front Axle Spindle to Axle Shaft Seal Fits 1968-1972 Ford Dana 44 axles with QU40324 2" outside diameter Spindle Slinger. This one piece Seal was used on most 1970-1972 4x4's with open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20040 First Design 1973-1976 Dana 44 Open Knuckle V-Seal Spindle Seal Fits some 1973-1976 Ford Bronco/F150 4x4's that originally came with the 2" ID Rubber V-Seal. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40324 Early Dana 44 Small Outer Axle Shaft Slinger Is a genuine original equipment New Old Stock (NOS) steel flinger or slinger for 1968 to 1972 Ford Dana 44 axles that use 2" Inside diameter spindle to axle shaft seals. Diameter of seal surface is 2". More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4734 Front Axle Shaft Spindle Bearing Set Fits 1966 to 1979 Ford Dana 44 open knuckle front axles. One bearing is pressed into each spindle to support the outer axle shaft. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40232 Early Type Brass Axle Shaft Thrust Washer Measure just under 1.875" outside diameter. This thrust washer was used on 1966-1972 Ford 1/2 ton 4x4's with open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40056 Small Spindle to Axle Shaft V-Seal Is a genuine original equipment 1-5/16" ID Rubber V-Seal that is installed in your spindle between QK4734.5 Spindle Bearing and QU40070 Spindle Thrust Washer. Fits 1976 to 1979 Ford Dana 44 front axles. Will also fit 1973-1975 axles with replacement spindles that have a recessed spindle bearing. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40070 Axle Shaft to Spindle Thrust Washer Is a genuine original equipment plastic thrust washer that controls axial thrust between your outer axle shaft and spindle. Fits most 1973 to 1976 and all 1977 to 1979 Ford Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40071 2nd Design Large Axle Shaft to Spindle V-Seal Is a genuine original equipment 2.25" ID Rubber V-Seal that seals between your axle shaft and spindle. Fits most 1973 to 1976 and all 1977 to 1979 Ford Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4739 Spindle Seal Kit Services both sides on your 1974 to 1976 Ford Dana 44 front axle with 2nd design V-Seal and all 1977-1979 axles. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40228 Spindle Bearing and Seal Kit Services one side on your 1974 to 1979 Ford Dana 44 front axle with 2nd design V-Seal and all 1977-1979 axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40058 Outer Axle Shaft Slinger Acts both as a crud deflector and a sealing surface on open knuckle axles. Replace anytime they are dinged, bent or badly corroded. Fits most 1973 to 1976 and all 1977 to 1979 Ford Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Knuckles

top_page
photo

QU20614U Used Right Steering Knuckle for 1978-1979 4x4 Ford F150 regular cab and Bronco. Used in 610066 and 610067 BOM numbers. More Info

 

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20615U Used Left Steering Knuckle for 1978-1979 4x4 Ford F150 regular cab and Bronco. Used in 610066 and 610067 BOM numbers. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 44 front axle in your 1966-1979 F-100/F-150 or 1971-1979 Ford Bronco 4x4s.

photo

QT1044 Inner Pinion Bearing Installer For Dana 44 front axles in 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1115 Dana 44 Differential Side Bearing Installer For Dana-Spicer Model 44 front 4x4 front axles. QT1115 features a raised internal ring that contacts the bearing inner face so you can press or drive your diff bearings on without damaging the cage. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1812 Outer Pinion Bearing Cup Installer Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50533 Outer Pinion Bearing Cup a simple and fast procedure. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1032 Case Spreader Is used to relieve the differential bearing preload making it easy to safely remove and install your front differential without damaging expensive critical parts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1803 Inner Wheel Bearing Cup Installer For 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1802 Outer Wheel Bearing Cup Installer For all 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1504 1966-1969-5 Wheel Seal Installer For all 1966-1969.5 Ford F-100 and Bronco Dana 44 Front Axles. Does NOT fit QU90001 Seal used on 1969.5 to 1975 hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1502 1969.5-1979 Wheel Seal Installer For all 1969-1/2 to 1979 Ford F-100, F-150, and 1971-1979 Ford Bronco Dana 44 Front Axles. Does NOT fit QU50654 Seal used on 1959-early 1969 hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1012i 4 Lug Spindle Nut Socket For all 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 front axles
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1025 Universal Spindle Nut Socket For all 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT5500 Wheel Bearing Packer Takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your Ford 4x4! More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1023 Triple Thread Universal Spindle Puller Use with any 5/8" fine thread slide hammer to quickly and easily remove those rusted in front wheel bearing spindles on your 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos Dana 44 front axles without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials on 1966-1979 Dana 44 Front Axles. Also works on most Dana 50IFS, Dana 44, Dana 30, Dana 27, and Dana 25 front axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1200 Tie Rod Separator Allows you to remove the separate tie rod and drag link ends without wrecking the seals or screwing up your steering linkage ends. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TS4933 Front Inner Axle Seal Installer Tool Set for Dana 44 front axle with QU40160 2-5/8" OD Seals. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals (Individual)

top_page
product note

Ford used the same wheel bearings for all 1966 to 1979 F-100, F150 and 1972-1979 Bronco 4x4s with Dana 44 open knuckle front axles. For the trucks, here is a choice between two different wheel seals with the change occurring in mid-model year 1969. QU50578 Seal is are correct for 1966-1968 vehicles and 1969 F-100s up to serial number F70000. QU90001 fits 1969 F-100s starting with serial number F70001 and 1970 to 1979 F-100, F150 plus 1972-1979 Broncos.

photo

QU50447 Timken® Outer Wheel Bearing Cup For all 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50448 Timken® Outer Wheel Bearing For all 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50577 Timken® Inner Wheel Bearing Cup For all 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50578 Timken® Inner Wheel Bearing For all 1966-1979 Ford F-100/F-150 4x4 trucks and 1971-1979 Ford Broncos with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50654 1966 to 1969-1/2 Inner Wheel Seal for Ford Dana 44 Internal Spline Wheel Hub Fits all 1966-1968 Ford F-100 and 1969 models with vehicle serial numbers up to F70000. Seal width is 1/4", seal outside diameter is 3-1/4". More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90001 1969-1/2 to 1975 Inner Wheel Seal for Ford 44 Internal Spline Wheel Hub Fits all 1969.5 to 1975 Ford F-100, F150 vehicle serial numbers after F70000. Also fits 1971-1979 Broncos. Seal outside diameter is approximately 3-21/64". More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
product note

Ford used the same wheel bearings for all 1966 to 1979 F-100, F150 and 1972-1979 Bronco 4x4s with Dana 44 open knuckle front axles. For the trucks, here is a choice between two different wheel seals with the change occurring in mid-model year 1969. QU50578 Seal is are correct for 1966-1968 vehicles and 1969 F-100s up to serial number F70, 000. QU90001 fits 1969 F-100s starting with serial number F70000 and 1970 to 1979 F-100, F150 plus 1972-1979 Broncos. Kits include Timken® Wheel Bearings and North American made Wheel Seals, plus you can order a Kit with or without install tools!

photo

TK4911F Torque King® Master Wheel Bearing Kits with Tools for 1966-1969.5 Ford Dana 44 Front Axles Fit 1966 to 1959-1969.5 F-100 4x4 trucks with standard Dana 44 open knuckle front axles. 1969 vehicles that use this Kit will have a serial number below F70001. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4912F Torque King® Wheel Bearing Parts Only Kits for 1966-1969.5 Ford Dana 44 Front Axles Fit 1966 to 1959-1969.5 F-100 4x4 trucks with standard Dana 44 open knuckle front axles. 1969 vehicles that use this Kit will have a serial number below F70001. Includes Timken® Bearings with Bearing Cups and 2 Wheel Seals. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4711 Torque King® Master Wheel Bearing Kits with Tools for 1969.5-1979 Ford Dana 44 F100, F150, Bronco Open Knuckle Front Axles Fit 1969.5-1979 F100, F150, and 1971-1979 Broncos with standard Dana 44 open knuckle front axles. 1969 vehicles that use this Kit will have a serial number above F70000. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4780 Torque King® Wheel Bearing Parts Only Kits for 1969.5-1979 Ford Dana 44 F100, F150, Bronco Open Knuckle Front Axles Fit 1969.5-1979 F100, F150, and 1971-1979 Broncos with standard Dana 44 open knuckle front axles. 1969 vehicles that use this Kit will have a serial number above F70000. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Discontinued Tools

top_page
photo

QT1815 Inner Pinion Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50539 Inner Pinion Bearing Cup a simple and fast procedure. Superseded by QT1812.

photo

QT1097 Differential Master Bearings Slip on your differential in place of the taper bearings and cups. Used along with a dial indicator to determine the correct differential shim thickness. Discontinued.

photo

QT9018 5 Pound Dead Blow Hammer Is just about the first tool you will reach for to do a multitude of jobs on your Ford 4x4. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool. Discontinued.