Parts for Dana 44 Open Knuckle Front Axles in 1976-1979 Ford F-250 4x4 Trucks

We have a good selection of parts for 1976 to 1979 Ford F-250 Dana 44 open knuckle front driving axles. Starting with the 1976 model year, Ford F-250 4x4 trucks were built with an open knuckle, disc brake, Dana 44 monobeam axles which replaced the drum brake, closed knuckle design Dana 44 which had been used since 1959. Initially, Ford retained the remote mount transfer case, high-boy chassis but with a Dana 44 open knuckle front axles instead of a closed knuckle axle used through 1975. The 1976-1977-1/2 axles can be identified by the type of wheel hub used. These 1976-1977-1/2 axles have disc brakes and a wheel hub that is drilled and tapped on its outboard face in order to bolt on either a solid drive flange (full time) or external mount plastic dial Spicer hub lock (part time). 1977.5-1979 F-250 trucks are low riders with direct mount transfer cases. All 1977.5-1979 Dana 44 axles used an internal spline type wheel hub. Heavy-duty trucks could be ordered with an available 4500-pound capacity Dana 60 front axle for 1978 and 1979. 1979 was the last year Ford used a beam type Dana 44 front axle in the F-250 series. From 1980 through 1997, all 4x4 F-250 trucks used an Independent Front Suspension (IFS) drive axle.

Axle Identification

top_page
photo

Cover: 10 Bolt, 10-3/8" high

Suspension: Leaf spring

Ball Joints: Open Knuckle Pressed in Steering Knuckle, nuts at top

Wheel Hubs up to 1977 Serial Number Y20000 are drilled and tapped on the outboard end with six 3/8" coarse thread holes for mounting an external type hublock or drive flange

photo

Wheel Hubs from 1977 Serial Number Y20001 are internally splined for a splined hub drive gear or internal mount hublock

Brakes: Disc

Axle Shafts

top_page
photo

TK40922 1976-1977.5 Torque King® Outer Axle Shaft for F250 High Boy Is a heavy-duty, USA made replacement Outer Axle Shaft for all 1976-1977.5 Ford F250 4x4 trucks with open knuckle Dana 44 front axles. These rugged 19 spline outer axle shafts are made from thru-hardened and extra tough USA made steel. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40158 1977.5-1979 Outer Axle Shaft for F250 Low Boy 4x4s With Dana 44 Front Axles is a genuine Dana part for either side side of your vintage Ford F250 Dana 44 open knuckle front axle. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40639 1976-1979 Left Inner Axle Shaft Is a genuine Dana original equipment Left (Drivers Side) Inner Axle Shaft for all 1976-1979 Ford F250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40640 1976-1979 Right Inner Axle Shaft Is a genuine Dana original equipment Right (Passenger Side) Inner Axle Shaft for all 1976-1979 Ford F250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Seals and Seal Kits for Inner Axle Shafts

top_page
product note

Ford used two different Inner Axle Shaft oil seals in 1976-1979 era F250 Dana 44 open knuckle front axles. An Inner Axle Seal is pressed in the inboard end of each axle tube, right next to the differential side bearings. These seals contact the inner axle shafts to prevent gear oil from running out of the differential and down the axle tubes. Old age, blown axle u-joints, and/or grit that works it's way into the axle tubes and cuts the seal are the usual causes of failure. A bad Inner Axle Shaft Seal can be detected by oil coming out the end of the axle tubes next to the axle shaft u-joint. Usually when these Seals start to fail, they will seep oil so the leakage may go undetected for quite some time. Many a ring and pinion set has been burned up from axles that lost all their lube when long term seepage was not noticed.

photo

QU40055 1976-1978 Inner Axle Shaft Seal for F250 Is a genuine Dana replacement Seal for 1976-1978 F250 4x4s with the open knuckle Dana 44 front axle. QU40055 is a unitized seal that combines an axle shaft guide and inner axle shaft seal in one part. One of these Seals are installed in each axle tube, right next to the differential to keep gear lube from leaking out the ends of the axle housing.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40159 1979 Inner Axle Shaft Seal for F250 4x4s with the open knuckle Dana 44 front axle. One of these Seals are installed in each axle tube, right next to the differential to keep gear lube from leaking out the ends of the axle housing. QU40159 fits all 1979 Ford F250 Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4872 1976-1978 Ford Dana 44 Axle Seal Kit with Adjustable Depth Axle Seal Tool Set Quickly and easily installs QU40055 Inner Axle Seals in 1976-1978 Ford F-250 3/4 ton 4x4 Dana 44 open knuckle front axles. QT1165 Installer tool does not have a depth stop so you can offset the seal to clear a worn spot in the axle shaft, however, for a reference point, you will need to check the depth of the old seals before removing them. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4871 1976-1978 Ford Dana 44 Axle Seal Kit with Fixed Depth Axle Seal Tool Set Quickly and easily installs QU40055 Inner Axle Seals to a precise depth in 1976-1978 Ford F-250 3/4 ton 4x4 Dana 44 open knuckle front axles. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4830 1979 Ford F250 Dana 44 Axle Seal Kit with Adjustable Depth Axle Seal Tool Set Quickly and easily installs QU40159 Inner Axle Seals in 1979 F250 Dana 44 Front Drive Axles. Our unique installer design allows you press in new your Inner Axle Seals to a different depth to miss a groove worn in your axle shaft by the old seal. New Seal is installed without damage because the CNC Precision Machined Installation Tool cups the seal so force is only applied on the steel seal shell. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note

We offer three different Universal Joints for your hard working 1976 to 1979 Ford F-250 4x4 Truck with a Dana 44 solid front axle. Both are good, reliable products, but different manufacturing techniques and seal types will have a major influence on the ultimate life of the joint. Our most popular choice is our TK40712 cold-forged, non-greaseable, original equipment replacement U-Joint. The wear-resistant cold-forged cross and superior sealing make it the best choice for both low maintenance and long life. QU40754 and QU90007 are hot-forged and are equipped with single lip seals. They are greaseable through a flush fitting threaded into one of the caps. With good maintenance and quality lubricant like our QU90018 Pyroplex® Plus Grease, these joints will last and last. Click on the Part Number Links to see our individual product pages for more info.

photo

TK40712 Torque King® Premium Non-Greaseable Axle U-Joint for 1976-1979 Ford F-250 Dana 44 Front Axles Best Quality Original equipment type universal joint with Premium Cold-Forged cross and superior pressure-type seals. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90007 Greaseable Axle U-Joint with Rubber Seals For 1976-1979 Ford F-250 Dana 44 Front Axles Value priced with Hot-Forged cross and flexible rubber seals. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ball Joints

top_page
product note

The 1976-1979 Ford Dana 44 Beam Type open knuckle front axle uses replaceable Ball Joints pressed into the steering knuckle. Both Ball Joints are weight bearing. A threaded adjuster that screws into the upper hole of the axle yoke is used to provide preload on the Ball Joints. Dana has modified the seal configuration on the current production parts, but the high quality and basic Ball Joint design has remained unchanged since the early 1970's. Over the years we have found the average Ball Joint life of our non-greaseable, factory Dana Ball Joints to be 7 to 10 years for vehicles used as daily drivers and/or work vehicles.

photo

QU40187 Original Equipment Ball Joint Set for 4x4 Bolt Front Axles Are the current production original equipment, factory lubed, Upper and Lower Ball Joints with hardware for 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
product note

1976 is the first year Ford offered disc brakes on F250 4x4s as either an option or stock equipment. All 1976-1979 Ford F250 4x4 trucks with Dana 44 front axles were equipped with disc brakes and dual piston brake calipers.

photo

QU20054 Front Disc Brake Caliper Tension Spring For 1976-1979 Ford F250 Dana 44 front axle with dual piston calipers. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU80002 Caliper Slide Lock Bolt Is a special, hex head bolt that threads into the caliper anchor plate on your disc brake equipped 1976 to 1979 Ford F250 4x4 truck. The tapered body between the threads and end fits into the inner notch of the caliper slide or key. QU80002 is plated for corrosion resistance. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings (Individual)

top_page
product note

All 1976 to 1979 Ford F-250 4x4 trucks with open knuckle Dana 44 Front Axles use the same differential and pinion bearings.
All bearings are not created equal for fit or durability, so we only stock first class, long lasting, Timken® Differential and Pinion Bearings for your Dana front axle. Timken® was and is a a major original equipment supplier of top-notch bearing components to Dana Spicer. Since I first started rebuilding Dana axles in the mid 1970's, I have found Timken® Bearings to be the most consistent in relation to the published dimensions of any bearing on the market which makes rebuilding an axle right the first time a WHOLE lot easier!

photo

QU50533 Timken® Outer Pinion Bearing Cup For 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50534 Timken® Outer Pinion Bearing For 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50535 Timken® Inner Pinion Bearing Cup For 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50536 Timken® Inner Pinion Bearing For 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50538 Timken® Differential Side Bearing For 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. (uses 2.) More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50537 Timken® Differential Side Bearing Cup For 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. (uses 2.) More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing and Seal Kits

top_page
product note

Most 1976-1979 F-250 3/4 ton trucks with open knuckle Dana 44 Front Axles used part time transfer cases and have lockout hubs. With a part time transfer case and lockout hubs, the axle shafts and differential parts do not rotate, so extreme diff/pinion bearing wear is rather rare except in work trucks. However, the flip side is water condensation in the diff has a tendency to cause rust and pitting of the bearings. If your vintage Ford has been used a lot in 4x4 mode or parked outside and subject to temperature changes, there is a good chance that significant wear or water damage may have occurred on your differential and pinion bearings. When you replace the bearings, do not forget to replace the inner axle shaft oil seals.

photo

QU50576 Differential Bearing and Seal Kit For 1976-1979 Ford F-250 3/4 ton 4x4 trucks with the Dana 44 open knuckle front axle features first class Timken® Differential and Pinion Bearings, plus Pinion Seal, Pinion Nut, Crush Sleeve, Gear Marking Compound, Threadlocker, and RTV Sealant. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
product note

Most 1976-1979 Ford F250 Dana 44 Front Axles were factory equipped with conventional open differentials. An optional Trac-Lok® limited slip differential was offered. Depending upon the year, both full time and part time transfer cases were used to drive the front axle. In vehicles having full time transfer cases in which the front axle is always under power when driving, wear on the thrust washers and cross shaft can be expected on higher mileage vehicles. The differential small parts are the same for all ratios, but the ring gear flange on the case castings are different for 3.73 and numerically lower ratios and axles having 4.09 and numerically higher ratios due to the pinion gear diameter size for high and low ratios.

photo

QU40000 Dana 44 Pinion Mate Thrust Washer Is a genuine Dana hardened concave thrust washer that fits between each of the small diameter pinion mate gears in your 1976-1979 Ford F250 Dana 44 open differential. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40033 Dana 44 Side Gear Thrust Washer Is a genuine Dana hardened flat thrust washer that fits between each of the splined differential side gears in your 1976-1979 Ford F250 Dana 44 open differential. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40001 Dana 44 Differential Cross Shaft Retaining Pin Is a genuine Dana spring steel Pin used to retain your differential cross shaft in the diff case for 1976-1979 Ford F250 with open differentials. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40003 Dana 44 Differential Cross Shaft Is a genuine Dana hardened steel shaft that acts as the axle for the two small pinion mate gears for all 1976-1979 Ford F250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40178 30 Spline Dana 44 "Spider Gear" Kit Is a genuine Dana Inner Differential Parts Kit for open differentials in Dana 44 axles with 30 spline inner axle shafts. QU40178 fits 1976-1979 Ford F250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU30170U Loaded Differential Case For Dana 44 with 3.92 to 5.89 ratio gear sets and 30 spline axle shafts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40632 Empty Differential Case Kit For Dana Model 44 3.73 and numerically lower ratios. Includes ring gear bolts and diff shims. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40633 Loaded Differential Case Assembly For Dana Model 44 3.73 and numerically lower ratios. Includes spider gears, diff bearings, ring gear bolts and diff shims. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40634 Empty Differential Case Kit For Dana Model 44 3.92 and numerically higher ratios. Includes ring gear bolts and diff shims. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40635 Loaded Differential Case Assembly For Dana Model 44 3.92 and numerically higher ratios. Includes spider gears, diff bearings, ring gear bolts, and diff shims. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Makers

top_page
product note

In the mid 1970's Dana made a differential cover design change to heavy gauge covers with flat mating flanges. Unlike the previous, thin gauge covers with embossed flanges which were made for use with a cut gasket, the new design, thick gauge covers are designed for sealing with RTV. If you desire, you can still use a gasket with the new type cover by combining the gasket with thin films of RTV. We stock both Ultra Gray RTV Sealant and genuine Dana Gaskets.

photo

TK40573 Torque King® 6 Bolt Front Hub Gasket For 1976-1977.5 Ford F-250 an Open Knuckle Dana 44 Axle with 6 Bolt external mount lockout hubs is a brand new, precision cut, high-tech hub gasket. TK40573 fits all 1976 and 1977 F250 4x4s before serial number Y20001. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40395 Special Inner Metal Hub Gasket For Ford Factory Spicer Free-Running Factory Hubs on 1976-1977.5 3/4 ton Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42028 Dana 44 High Performace Reusable Different Cover Gasket Genuine Dana part. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40214 Dana 44 Cover Gasket Is a genuine original equipment Dana Gasket for all Dana-Spicer Model 44 axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hubs and Hub Parts

top_page
product note

1976 to 1977-1/2 model year Ford F-250 4x4 trucks with Dana 44 open knuckle front axles up to 1977 serial number Y20000 have a wheel hub that is drilled and tapped on its outboard face in order to bolt on either a solid drive flange (full time) or external mount plastic dial Spicer hub lock (part time). 1977.5-1979 F-250 trucks with Dana 44 axles from 1977 serial number Y20001 all used the internal spline type wheel hub. For all Dana 44 axles in part time F-250 models of the 1976-1979 era, the factory hub locks were made by Dana Spicer, but except for the axle shaft snap rings, no parts are interchangeable between the 1977.5-1979 internal mount and 1976-1977.5 external mount hub-locks.

photo

QU51181 Warn 20990 Premium Hub Set for Dana 44 Front Axles With internally splined front wheel hubs. Reliable and good looking. QU51181 Fits most Ford Dana 44 1976-1979 F250 4x4s.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56018 Warn Manual Hub Set Is a reliable, original equipment quality hub set with installation hardware for all part time transfer case equipped 1977.5-1979 F250 4x4s with Dana 44 Front Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56019 1 Side Warn Manual Hub Set More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4918 Hub Service Kit For QU56018 Warn Manual Hub Set. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40044 Hub Dial O-Ring For Dana original equipment plastic dial, spline mount factory hubs used on 1977.5 to 1979 Ford F-250 Dana 44 front axles with internally splined wheel hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40699 Large Hub Plate to Wheel Hub Internal Snap Ring For Dana original equipment, plastic dial, spline mount factory hubs used on 1977.5 to 1979 Ford F-250 Dana 44 front axles with internally splined wheel hubs.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40032 Axle Shaft Snap Ring Is a genuine original equipment part for 1977.5 to 1979 Ford F-250 4x4s with Dana 44 Front Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40154 Hub Cam Body for Spicer Plastic Dial Internal Mount Hubs Is a new old stock (NOS) genuine Spicer replacement part for original equipment Spicer Lockout Hubs used on 1977.5 to 1979 Ford F-250 Dana 44 front axles with internally splined wheel hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40050 Spicer Tapered Hub Spring For 1977.5-1979 F-250 trucks Dana 44 front axles with internally splined wheel hubs equipped with either Spicer Plastic Dial factory hub-locks or full time drive gears. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40035 Hub Spring Plate Fits between the QU40050 hub spring and the outer wheel bearing cup on 1977.5 to 1979 standard duty Ford F-250 Dana 44 front axles with internally splined wheel hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20351 1977.5-1979 New Hub and Rotor Assembly With 1/2" wheel studs fits all Dana 44 equipped 1977 F250 4x4 starting with serial number Y20001 and all 1978-1979 F250 4x4 trucks with the stock Dana 44 front axle. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20466U Used 1976-1977.5 Front Wheel Hub For 1976-1977-1/2 Ford F250 4x4 trucks with disc brake equipped Dana 44 open knuckle front axles. Fits all 1976 4x4 F-250 Dana 44 front axles and early 1977 front Dana 44 axles on F-250 4x4 trucks with Y20000 and lower serial numbers. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50818 Warn Premium Quality 6 Bolt External Mount Hub Set For 1976-1977.5 Ford F250 3/4 Ton 4x4s with Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50160 Small Selectro Hub Cam Fits popular aftermarket replacement Selectro and Dualmatic Classic series hubs with big cast iron dials that were widely sold in the late 1970 and 1980s to replace malfunctioning OEM hubs. This 2-5/8" OD plastic cam is a genuine replacement part for the original failure prone, cast aluminum hub cams most of these hubs were built with. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40256 Torque King® Red Heavy-Duty Anodized Aluminum Replacement Hub Dial is a precision made, CNC machined anodized aluminum replacement Dial for 1976-1977-1/2 Ford F-250 3/4 ton trucks with the big Dana 6 Bolt factory installed, external mount hubs. Sold Individually.
More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40471 Hub Dial Sealing Ring Is a V-Seal type sealing ring that fits TK40256 Hub Dial. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20112 Spicer Hub Dial Snap Ring Fits 1976-1977-1/2 heavy-duty Ford F-250 Dana 44 front axle with factory installed Spicer external mount hubs. More Info

photo

QU40918 Hub Dial Actuating Cam Pin For Dana factory 3/4 ton QU40256 plastic dial lockout hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40406 Hub Cam For external mount hubs fits early to mid 1970's Ford 3/4 ton trucks with Dana model 44 front axles and factory installed, Dana external mount (6 3/8" bolts) hubs. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20253 Hub Cam Lock Ring For QU40406 Hub Cam is a genuine replacement part for Ford F-250 Crew Cab 3/4 ton trucks with the big Dana-Spicer 6 Bolt factory installed, external mount hubs. Holds the QU40406 Hub Cam in the QU20114 Hub Clutch Gear.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40427 Dana 44 Full Time Front End Hub Cap for 1978-1979 F250 Ford trucks with Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20109 Spicer Hub Axle Shaft Drive Gear fits 1976-1977-1/2 heavy-duty Ford F-250 Dana 44 front axle with factory installed Spicer external mount hubs. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20114 Spicer Hub Clutch Gear with Pressed in Bushing Fits 1976-1977-1/2 heavy-duty Ford F-250 Dana 44 front axle with factory installed Spicer external mount hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40547 Spicer Splined Hub Body Fits 1976-1977-1/2 heavy-duty Ford F-250 Dana 44 front axle with factory installed Spicer external mount hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40257 Dana Spicer Hub Bluffer External mount hubs are genuine original equipment replacement socket head bolts. Fits 1976-1977-1/2 heavy-duty Ford F-250 Dana 44 front axle with factory installed Spicer external mount hubs. 3/8"-16 thread. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40595 Hub Spring For Spicer OEM plastic dial external mount lockout hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40596 6 Bolt, 19 Spline Front Hub Drive Flange For 1976 and 1977 (before serial number Y20001) Ford F-250 trucks with Dana 44 front axles and full time NP203 transfer cases. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40597 Drive Flange Hub Cap For 1976 and 1977 (before serial number Y20001) Ford F-250 trucks with Dana 44 front axles and full time NP203 transfer cases. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42038 O-Ring for the Hub Cap on Dana 60 front axles in 1977.5-1979 Ford 4x4's with Dana 60 axles equipped with factory installed Dana plastic dial spline mount hub locks.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20389U One Functional Used Dana Factory Lockout Hub and Red Dial fits 1976-1979 Ford F250 with Dana 44 front axles with splined wheel hubs. Complete except for QU40035 Spring Plate which must be ordered separately. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals and Technical Information

top_page
product note

Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations.

photo

TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles Covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts

top_page
product note

Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings.

photo

S24200 Blue Threadlocker For spindle and ring gear bolts etc. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S81343 Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding. Available in 2 sizes. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT9404 Application Brush Is ideal for applying Gear Marking Compound or Anti-Seize Lubricant to parts. Brush fibers and steel handle are resistant to most automotive chemicals. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S82194 Ultra Grey RTV Sealant Of all the automotive RTV sealants, this is about the best we have found for both high adhesion and resistance to both conventional and synthetic gear lubricants. We use this on almost all differential covers that were originally factory sealed with RTV. 3.5 ounce Squeeze Tube. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90018 Pyroplex® Protection ES Synthetic Grease Provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions! More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90016 SynPower® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90015 High Performance Synthetic Arctic Grease Is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90017 Red Grease Is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. Cartridge or 1 pound Tub. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals and Pinion Yokes

top_page
product note

Ford used two different Dana 44 front Pinion Yokes on 1976 to 1979 Dana 44 open knuckle front axles. 1976-1977.5 F250s with part time transfer cases used 26 spline front axle Pinion Yokes made to take "QU40772 3-5/8" wide front universal joint with 1-1/16" diameter cups. 1976 and 1977.5 F250 4x4s with the New Process NP203 full time transfer case have Double Cardan Front Constant Velocity Driveshafts using 3-7/32" wide universal joints and use QU40849 Yoke. Most 1977.5-1979 F250's use the larger QU40848 Yoke, but there are a few with QU40849 Yokes.

photo

QU40215 Dana 44 Front Axle Pinion Seal Is a genuine original equipment pinion seal for all 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40849 U-Bolt Style 1310 Dana 44 Full Time Front Pinion Yoke is a stock type Pinion Yoke that fits 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles and NP203 full time transfer cases. U-Joint width is 3-7/32". Use with QU40768 U-Bolt Kit. More Info
Also see QU40734 Strap and Bolt style Yoke.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40734 Strap and Bolt Style 1310 Series Pinion Yoke for Full Time Dana 44 Front Axles Is a USA Made, 26 spline replacement, Strap and Bolt style pinion yoke for Ford Dana 44 axles. Use with QU40735 Strap and Bolt Kit. Includes pinion slinger made to match QU40215 Pinion Seal. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40768 1310/1330 Driveshaft U-Bolt Kit for Stock Pinion Yoke Fits original equipment type pinion yokes on 1976-1979 Ford F-250 3/4 ton 4x4 trucks with stock type front axle pinion yokes made for 1-1/16" diameter cups. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40848 1330 Dana 44 Replacement Pinion Yoke Is a genuine Dana Yoke that fits 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles and part time transfer cases. U-Joint width is 3-5/8". More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40735 U-joint Strap and Bolt Kit for QU40848 Pinion Yoke Is used to attach your front driveshaft to QU40739 Dana 44 Replacement Pinion Yoke. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40905 Driveshaft U-Bolt Kit for 1350 and 1410 Series U-Joints fits many vintage axle, transfer case, and transmission yokes from the mid 1940's to the mid 1980's on Chevy, Ford, and GMC 4x2 and 4x4 vehicles up to 1-1/2 ton size used u-bolt style yokes for Spicer series 1350 or 1410 series universal joints. This u-bolt kit fits a great many of those yokes. Use this Kit to replace broken or stripped original u-bolts. Made in U.S.A.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
product note

The ring and pinion gear sets used in 1977.5-1979 Ford F250 stock Dana 44 front axles have a reverse cut or spiral compared to the conventional Dana 44 gear sets found in 1976-1977.5 F250s. The engineering reason for this is the pinion gear in 1977.5-1979 F250 Ford Dana 44 axles is located above the axle center line. Reverse Spiral Gear Sets are NOT interchangeable with standard Dana 44 gear sets.

QU40447 1976-1977.5 Genuine Dana 3.54 Ring and Pinion Kit With pinion bearings and small parts for 1976-1977.5 Ford F250 High Boy Dana 44 front axle. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40177 1976-1977.5 Genuine Dana 4.09 Ring and Pinion Kit With pinion bearings, pinion seal, and small parts for 1976-1977.5 F250 High Boy front Dana 44 axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU42013 1977.5-1979 4.09 Ratio Ford Dana 44 Reverse Spiral Ring and Pinion Kit is a genuine Dana Gear Set for Ford high pinion Dana 44 front axles in 1977.5-1979 F250 Low Boy 4x4s. QU42013 includes a matched, reverse cut Dana ring and pinion set, pinion bearings with cups, pinion seal, pinion nut, pinion washer, pinion slingers, pinion shims, differential shims, and ring gear bolts. More Info
Also available while supplies last: QU42012U Used 4.09 Ratio Reverse Spiral Ring and Pinion Gear Set

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note

Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else.

photo

QU40209 Dana 44 Ring Gear Bolt For Dana 44 Axles. Genuine Dana-Spicer Grade 9 Bolt has locking teeth under the hex head to prevent loosening under any load conditions. More Info

Dan the Gear Man® Safety Note: Ring Gear Bolts are designed for a single use. They must be replaced after they are removed!

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40343 Dana 44 Hardened Differential Cap Retaining Bolt Genuine original equipment hex-head bolt for Dana Spicer Model 44 front axle differential bearing caps fits all 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40540 Spindle to Knuckle Bolt For 1976-1979 Ford F250 4X4 Trucks with Dana44 open knuckle front axles. Thread size is 7/16 x 20 threads per inch. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40028 Dana 44 Inner Pinion Bearing Slinger Is a genuine Dana original equipment Oil Slinger. QU40028 fits between your Dana 44 axle's inner pinion bearing and pinion head. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40448 Dana 44 Inner Pinion Bearing Oil Baffle Is a genuine Dana original equipment stepped, stamped steel Oil Baffle. QU40448 fits between your Dana 44 axle's inner pinion bearing cup and the axle housing on 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40002 Outer Pinion Bearing Slinger QU40002 is a genuine Dana-Spicer part that fits between the outer pinion bearing and pinion yoke on 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40311 Dana 44 Front Differential and Pinion Shim Kit For 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. Genuine Dana-Spicer Shim Kit includes pinion depth shims, pinion preload shims, differential adjusting shims, pinion nut, pinion washer, and differential cover pan gasket. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40009 Dana 44 Axle Pinion Lock Nut Is a genuine Dana-Spicer original equipment replacement locking nut that fits 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40010 Dana 44 Axle Pinion Washer Is a genuine Dana-Spicer flat washer that fits between the pinion nut and pinion yoke on 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20106 2-5/16" OD Worm Shaft Bearing Cup For most F250 Trucks with manual steering gears. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20113 Manual Steering Gear Worm Shaft Seal For 1976-1977 F250 with steering gear TAG# D6TA-HA. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindles and Spindle Nuts

top_page
photo

QU40004 Inner Spindle Nut For 1976-1979 Ford F-250 Dana 44 Front Axle threads on the spindle and fits against your outer wheel bearing to provide correct wheel bearing end-play. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40060 Spindle Lock Washer For 1976-1979 Ford F-250 Dana 44 Front Axle locks your QU40004 Inner Spindle Nut in position when properly installed. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40031 Outer Spindle Nut For 1976-1979 Ford F-250 Dana 44 Front Axle is tightened against your QU40060 Spindle Lock Washer to keep it in place and it acts as a jam nut effectively locking both spindle nuts and the washer together. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4727 Spindle Nut Kit For 1976-1979 Ford F-250 Dana 44 includes one each of QU40004 Inner Spindle Nut, QU40060 Spindle Lock Washer, and QU40031 Outer Spindle Nut. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40332 Spindle for 1976-1977-1/2 F250 Is a replacement Spindle with Spindle Bearing and Seals for all 1976-1977.5 Ford F250 "High Boy" 4x4s. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU95036 7/16" Fine Thread Class C Lock Nut for Ford F250 Front Spindle Retention Is an American Made high-strength, all-metal locknut used to secure the front axle spindle to the steering knuckle on your 1976 to 1979 Ford 4x4 Dana 44 front axle. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40594 1977.5-1979 Ford F250 Dana 44 Front Spindle Kit Is an original equipment Front Axle Wheel Bearing Spindle for disc brake equipped Dana 44 front drive axles in 1977.5-1979 Ford F-250 "Low Boy" trucks.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Y440594 Replacement Front Spindle Kit for 1977.5-1979 Ford F250 with Dana 44 front axle is a low cost, yet high quality replacement part. Imported.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Bearings and Seals

top_page
product note

The dead spindle design of the 1976-1979 Ford F-250 Dana 44 front axle uses a needle bearing to support the outer axle shaft. To protect the bearing and control axial thrust, a 4 piece set consisting of an Axle Shaft Slinger, Large V-Seal, Small V-Seal, and Thrust Washer was used. We have both Kits and individual exact replacement Dana-Spicer Spindle small parts for your hard-working 1976-1979 Ford F-250 4x4.

photo

QK4734 Front Axle Shaft Spindle Bearing Set Fits 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. One bearing is pressed into each spindle to support the outer axle shaft. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40056 Small Spindle to Axle Shaft V-Seal Is a genuine original equipment 1-5/16" ID Rubber V-Seal that is installed in your spindle between QK4734.5 Spindle Bearing and QU40070 Spindle Thrust Washer. Fits 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40070 Axle Shaft to Spindle Thrust Washer Is a genuine original equipment plastic thrust washer that controls axial thrust between your outer axle shaft and spindle. Fits 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40071 Large Axle Shaft to Spindle V-Seal Is a genuine original equipment 2.25" ID Rubber V-Seal that seals between your axle shaft and spindle. Fits 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4739 Spindle Seal Kit Services both sides on 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40228 Spindle Bearing and Seal Kit Services one side 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40058 Outer Axle Shaft Slinger Acts both as a crud deflector and a sealing surface on open knuckle axles. Replace anytime they are dinged, bent or badly corroded. Fits 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Knuckles

top_page
photo

QU40540 Spindle to Knuckle Bolt For 1976-1979 Ford F250 4X4 Trucks with Dana 44 open knuckle front axles. Thread size is 7/16 x 20 threads per inch. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20474U Used Left Steering Knuckle with Steering Arm for 1976-1977.5 F250 4x4 trucks with Dana 44 disc brake front axle. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20475U Used Right Steering Knuckle for 1976-1977.5 F250 4x4 trucks with Dana 44 disc brake front axle. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 44 front axle in your 1976-1979 F250 4x4.

photo

TS4872 Dana 44 Inner Adjustable Depth Axle Seal Tool Set Quickly and easily installs QU40055 Inner Axle Seal in your 1976-1978 F250 truck with Dana 44 front axles. Installer tool does not have a depth stop so you can offset the seal to clear a worn spot in the axle shaft, however, for a reference point, you will need to check the depth of the old seals before removing them. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TS4871 Dana 44 Inner Fixed Depth Axle Seal Tool Set Quickly and easily installs QU40055 Inner Axle Seal in your 1976-1978 F250 truck with Dana 44 front axles. Our unique installer design will press in your new Inner Axle Seals to the exact depth and without damage because the CNC Precision Machined Installation Tool cups the seal so force is only applied on the steel seal shell. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TS4830 Dana 44 Axle Seal Kit with Adjustable Depth Axle Seal Tool Only Set Quickly and easily installs QU40159 Inner Axle Seal in your 1979 F-250 truck with Dana 44 front axles. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1044 Inner Pinion Bearing Installer For Dana 44 front axles in 1976-1979 F250 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1818 Inner Pinion Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50535 Inner Pinion Bearing Cup a simple and fast procedure. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1812 Outer Pinion Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50533 Outer Pinion Bearing Cup a simple and fast procedure. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers. More Info
Also available: QT1101 14" Standard Duty Installer Driver Handle for deep seated seals and bearings
QT1116 8" Pro Duty Installer Driver Handle
QT1119 14" Pro Duty Installer Driver Handle for deep seated seals and bearings

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1115 Dana 44 Differential Side Bearing Installer For Dana-Spicer Model 44 front 4x4 front axles. QT1115 features a raised internal ring that contacts the bearing inner face so you can press or drive your diff bearings on without damaging the cage. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1032 Case Spreader Is used to relieve the differential bearing preload making it easy to safely remove and install your front differential without damaging expensive critical parts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1801 Bearing Cup Installer for Inner Wheel Bearing Cup On 1977.5-1979 F250 Dana 44 Front Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1802 Bearing Cup Installer for Outer Wheel Bearing Cup On 1976-1979 F-250 Dana 44 Front Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1805 Bearing Cup Installer for Inner Wheel Bearing Cup On 1976-1977.5 F-250 Dana 44 Front Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1502 Front Wheel Seal Installer For QU90001 seal on 1977.5-1979 F250 Dana 44 Front Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1506 Front Wheel Seal Installer For 1976-1977.5 F250 Dana 44 Front Axles. Specifically made for QU50101 Front Wheel Seals. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1012i 4 Lug Spindle Nut Socket For all 1976-1979 F250 Dana 44 Front Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1025 Universal Spindle Nut Socket For all 1976-1979 F250 Dana 44 Front Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT5500 Wheel Bearing Packer Takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your Ford 4x4! More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1024 Triple Metric and Standard Thread Spindle Puller Fits any 5/8" slide hammer to quickly and easily remove those rusted in front wheel bearing spindles on your 1976-1979 F250 Dana 44 Front Axle without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials. Also works on most Dana 50IFS, Dana 44, Dana 30, Dana 27, and Dana 25 front axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1200 Tie Rod Separator Allows you to remove the separate tie rod and drag link ends without wrecking the seals or screwing up your steering linkage ends. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals (Individual)

top_page
photo

QU50447 Timken® Outer Wheel Bearing Cup For all 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50448 Timken® Outer Wheel Bearing For all 1976-1979 Ford F-250 4x4 trucks with Dana 44 open knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50568 1976-1977.5 Timken® Inner Wheel Bearing Cup For all 1976-1977-1/2 Ford F-250 4x4 trucks with Dana 44 axles and externally mounted 6 bolt hub-locks or drive flanges. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50569 1976-1977.5 Timken® Inner Wheel Bearing For all 1976-1977-1/2 Ford F-250 4x4 trucks with Dana 44 axles and externally mounted 6 bolt hub-locks or drive flanges. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50446 1977.5-1979 Timken® Inner Wheel Bearing Cup For all 1977.5 to 1979 Ford F-250 3/4 ton 4x4 trucks with the standard Dana 44 closed knuckle front axles and internally splined wheel hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50412 1977.5-1979 Timken® Inner Wheel Bearing For all 1977.5 to 1979 Ford F-250 3/4 ton 4x4 trucks with the standard Dana 44 closed knuckle front axles and internally splined wheel hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90001 1977.5 to 1979 Inner Wheel Seal for Ford F250 Dana 44 Internal Spline Wheel Hub Fits all 1977.5 to 1979 Ford F-250 3/4 ton 4x4 trucks with the standard Dana 44 closed knuckle front axles and internally splined wheel hubs. Seal outside diameter is approximately 3-21/64". More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50101 1976-1977.5 Premium OE Type 3/4 ton Inner Wheel Seal For 1976-1977-1/2 Ford F-250 4x4 trucks with Dana 44 open knuckle front drive axles and 6 bolt, external mount drive flanges or lock-out hubs. QU50101 Premium OE Type Front Wheel Seal is interchangeable with QU50208 Flanged Front Wheel Seal. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50208 1976-1977.5 Flanged Inner Wheel Seal For all 1976-1977-1/2 Ford F-250 4x4 trucks with Dana 44 open knuckle front drive axles and 6 bolt, external mount drive flanges or lock-out hubs. QU50208 Flanged Front Wheel Seal is interchangeable with QU50101 Premium Front Wheel Seal. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
product note

It is always good preventative maintenance to replace the all wheel bearings and seals when restoring or maintaining your vintage 3/4 ton. The parts availability for decades old 4x4s declines on a daily basis. Wrecking a wheel hub and/or spindle when the old bearing you reused fails can either cost you a mint or put your broken-down truck on blocks forever. We stock high quality Timken® Wheel Bearings and North American made Wheel Seals to keep your big Ford rolling.

photo

TK4708F 1976 to 1977.5 Ford F-250 Torque King® Master Wheel Bearing Kits with Tools for Dana 44 Open Knuckle Front Axles Are specific for 3/4 ton F-250 4x4 Dana 44 front axles with external mount lockout hubs or drive flanges. TK4708F Master Kit includes 4 Timken® Bearings with Bearing Cups, 2 Wheel Seals, Bearing Cup Installers, Wheel Seal Installer and Driver Handle. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4779F 1976 to 1977.5 Ford F-250 Torque King® Wheel Bearing Parts Only Kits for Dana 44 Open Knuckle Front Axles Are specific for 3/4 ton F-250 4x4 Dana 44 front axles with external mount lockout hubs or drive flanges. Includes 4 Timken® Bearings with Bearing Cups and 2 Wheel Seals. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK4751 1977.5-1979 Torque King® Master Front Wheel Bearing and Seal Kits with Tools for Ford F250 Dana 44 Front Axles with internally splined wheel hubs These Kits fit 1977.5 to 1979 Ford F-250 4x4s with Dana 44 front axles. Do the job right the first time with premium quality parts and installation tools custom made for the job. TK4751 Master Kit includes 4 Timken® Bearings with Bearing Cups, 2 Wheel Seals, Bearing Cup Installers, Wheel Seal Installer and Driver Handle. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4752 1977.5-1979 Torque King® Front Wheel Bearing and Seal Kits for Ford F250 Dana 44 Front Axles with internally splined wheel hubs These Kits fit 1977.5 to 1979 Ford F-250 4x4s with Dana 44 front axles. Do the job right the first time with premium quality parts. Includes 4 Timken® Bearings with Bearing Cups and 2 Wheel Seals. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Discontinued Parts

top_page
photo

QU40754 Greaseable Axle U-Joint with Metal Backed Seals For 1976-1979 Ford F-250 Dana 44 Front Axles Better quality Axle U-Joint with Hot-Forged cross and metal backed rubber seals. Superseded to QU90007.

photo

QU40546 Spicer Hub Outer Chrome Cap Fits 1976-1977-1/2 heavy-duty Ford F-250 Dana 44 front axle with factory installed Spicer external mount hubs. Discontinued.

photo

QU40602 Hub Bushing For the big Dana-Spicer 6 Bolt with Spicer plastic dial external mount lockout hubs. Discontinued.

photo

QU40231 Spicer Hub Sealing Washer Is both a lockwasher and sealing washer. Discontinued.

 

Discontinued Tools

top_page
photo

QT1097 Differential Master Bearings Slip on your differential in place of the taper bearings and cups. Used along with a dial indicator to determine the correct differential shim thickness. Discontinued.

photo

QT9018 5 Pound Dead Blow Hammer Is just about the first tool you will reach for to do a multitude of jobs on your Ford 4x4. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool. Discontinued.