Parts for 1983.5-1996 Ford Bronco, F150, & F250 4x4s with Dana 44IFS Twin Traction Beam Front Axles

We stock a good selection of replacement parts for 1983.5 to 1996 Ford F-250 plus 1984-1996 Ford Bronco and F150 4x4s with Dana Spicer Model 44 Independent Front Suspension (IFS) Twin Traction Beam® drive axles. First used in 1980, the Ford IFS Twin Traction Beam® Dana 44 axle went through a significant differential and right side inner axle shaft design changes for vehicles built in 1983-1984.

Axle Identification

top_page
product note

Ford was the only vehicle manufacturer to use Dana Twin Traction Beam® Independent Front Suspension Axles which can be found on 1980-1997 model year Ford 4x4s. The Twin Traction Beam® IFS Axle line includes the coil spring Models 28 and 35 found in Bronco II, Explorers and Ranger pickups, the Model 44 which was used in fill size Broncos, F-150 (coil springs), and light duty F-250 pickups (leaf springs), and the leaf sprung 4500 to 4600 pound rated Model 50IFS axle in heavy GVW F-250 and 1980-1985.5 F-350 trucks. Dana 44IFS axles in F250 models after 1991 are uncommon and were probably only used on base model, light-duty regular cab vehicles. Dana does not list a 44 for F-250's after 1988, but Ford parts books do show a 3850# Dana 44IFS for regular cab F-250s as late as 1996.

Right Differential Output Shaft: The major difference between 1980-1983.5 and 1983.5-1997 Ford Dana 44IFS front axles is the way the right differential output shaft is supported and retained. The early axles use a pressed-on taper roller bearing and an external bolt-on retaining flange. Later production axles use a straight roller bearing pressed into the differential housing and the axle shaft is retained by a snap ring inside the differential next to the differential side gear. The early right diff output shafts could be pulled without removing the differential housing from the axle beam with a special slide hammer puller attachment, but seal replacement also requires the bearing be replaced. For later axles, you MUST remove the differential housing from the axle beam to access the snap ring, but once it is out replacing the right seal is quick and easy.

photo

Hub Size: Ford used both Dana 44 and Dana 50 IFS Twin Traction Beam® Front Axles in F-250 trucks. The easiest way to tell them apart is by measuring the diameter of the wheel hub or locking hub. F250 Dana 44 axles have wheel hubs that are approximately 3-5/8" in diameter. Dana 50 Hubs are about 4-1/8" in diameter.

Ball Joints: Pressed in Steering Knuckle, nuts at top

Axle Beams and Differential Housings

top_page
product note

The axle beams for Bronco and F150 are made to accept separate coil spring mounts. For the F250, the leaf spring sits directly on the axle beam.

photo

QU20515U Used Empty Dana 44IFS Diff Housing fits 1983-1991 Ford Bronco, F150, and F250 4x4s. More Info

$50.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50097 Axle Beam Pivot Bushing Fits either left or right axle beams. One of these Bushings gets pressed into the inboard end of each axle beam. More Info

$22.62
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20450U Good Used 1984-1996 Ford F250 Dana 44IFS Right Axle Beam is a good used right or passenger side Dana 44IFS axle beam for 1984-1996 Ford F250 4x4 trucks with 3800 or 3850 pound front axles.

Tech Note: These used axle beams are bare except for the original pivot bushing. Due to the age of these beams, we recommend you replace the pivot bushing with a new QU50097 bushing.

More Info

$145.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20451U Good Used 1984-1996 Ford F250 Dana 44IFS Left Axle Beam is a good used left or drivers side Dana 44IFS axle beam for 1984-1996 Ford F250 4x4 trucks with 3800 or 3850 pound front axles.

Tech Note: These used axle beams are bare except for the original pivot bushing. Due to the age of these beams, we recommend you replace the pivot bushing with a new QU50097 bushing.

More Info

$160.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20552U Used Right Axle Beam for Ford F150 Dana 44IFS. More Info

$150.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20553U Used Left Axle Beam for Ford F150 Dana 44IFS. More Info

$150.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shafts and Axle Shaft Assemblies

top_page
product note

Although all Ford Dana 44IFS axle shafts take the same u-joints, the inner and outer axle shafts have different lengths for Bronco/F150 and F250 models. There are also 2 possible outer axle shafts for Bronco and F150 for the 1987 to mid 1988 model years. The 1987-1988.5 Bronco and F150 4x4s with flat "pancake" hubs use an outer axle shaft that is almost 1-1/2" shorter than the type used on all Bronco/F150 models with internally splined front wheel hubs. In addition to new shafts we will stock some reconditioned axle shaft assemblies and some used individual axle shafts.

photo

QU50444 1/2 ton Front Outer Axle Shaft Is a genuine Dana part for 1983.5-1996 Ford Bronco F150 Dana 44IFS. 9.92" from end to center of U-Joint hole. Does NOT fit 1987-1988 with pancake front wheel hub. More Info

$146.15
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40624 1/2 Ton Left Inner Axle Shaft Is a genuine Dana part that fits ALL 1983.5-1996 Ford Bronco and 1983.5-1996 Ford F150 4x4 Dana 44IFS front axles.
More Info

$106.87
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40263 1/2 ton Right Inner Axle Shaft Is a genuine Dana part that fits ALL 1983.5-1996 Ford Bronco and 1983.5-1996 Ford F150 4x4 Dana 44IFS front axles.
More Info

$146.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40920 3/4 ton Front Outer Axle Shaft Is a genuine Dana part that fits ALL 1983.5-1996 Ford F250 4x4 Dana 44IFS front axles. Length from center of u-joint hole to end is 9-13/16".

More Info

$89.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40921 3/4 ton Left Inner Axle Shaft Is a genuine Dana part that fits ALL 1983.5-1996 Ford F250 4x4 Dana 44IFS front axles.

More Info

$158.01
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40616 3/4 ton Right Inner Axle Shaft Is a genuine Dana part that fits ALL 1983.5-1996 Ford F250 4x4 Dana 44IFS front axles. Length from center of u-joint hole to end is 23-21/32". More Info

$102.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40626 Dana 44IFS Right Axle Shaft Slip Yoke Is a genuine Dana part for all 1983.5-1996 Ford Bronco/F150 and 1983-1996 F250 4x4 trucks with Dana 44 Twin Traction Beam® IFS front axles.

More Info

$109.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40627 Dana 44IFS Right Differential Output Shaft Is a genuine Dana part for all 1983.5-1996 Ford Bronco/F150 and 1983-1996 F250 4x4 trucks with Dana 44 Twin Traction Beam® IFS front axles.

More Info

$179.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40377 F-250 Right Axle Shaft Assembly Is a genuine Dana factory assembly that includes QU40920 Outer Axle Shaft, QU40616 Inner Axle Shaft and a Dana factory lubed universal joint. Fits all 1983-1992 Ford F-250 4x4s with Dana 44IFS front axles.

More Info

$179.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QA40377R F-250 Reconditioned Right Axle Shaft Assembly Is a reconditioned axle shaft assembly and comes with a new u-joint. Fits all 1983-1992 Ford F-250 4x4s with Dana 44IFS front axles.

More Info

$110.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42042 Left Axle Shaft Assembly for 1993-1996 Ford Bronco and F150 Dana 44IFS front axles.

More Info

$322.20
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Seals and Seal Kits

top_page
product note

Ford introduced a redesigned Dana 44IFS Twin Traction Beam Front Axle during the 1983 model year that uses a right Differential Output Shaft retained by a C-Clip inside the axle housing. The new design requires the Differential Housing be removed from the left axle beam to service the Right Axle Shaft Seal and/or center axle universal joint. Also introduced was a right Axle Slip Joint protected by a flexible rubber Boot instead of a pressed on Yoke Seal. The Slip Yoke Boot eliminated one of the chronic problems the previous 1980-early 1983 axle had, namely axle shaft spline failure from water and grit infiltrating past the seal.

photo

QU40534 Right Side Differential Output Bearing and Seal Kit for Ford Dana 44 IFS Front Axles Is a genuine original equipment Kit that includes the right Axle Shaft Support Bearing, Right Axle Shaft Oil Seal and Axle Shaft Retaining Clip. Fits 1984-1996 Ford Dana 44 Twin Traction Beam IFS front drive axles. More Info

$21.51
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40087 Left Ford Dana 44 IFS Differential to Axle Shaft Seal Fits all 1983.5-1996 Ford Bronco/F150 and 1983-1996 F250 4x4 trucks with Dana 44 Twin Traction Beam® IFS front axles. More Info

$6.58
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40088 Right Ford Dana 44 IFS Differential to Axle Shaft Seal Fits all 1983.5-1996 Ford Bronco/F150 and 1983-1996 F250 4x4 trucks with Dana 44 Twin Traction Beam® IFS front axles that have the right inner axle shaft retained by a snap ring. More Info

$8.89
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40557 Axle Shaft Slip Yoke Seal for Ford Dana 44IFS Twin Traction Beam® Front Axles Is a genuine original equipment part for all 1983.5-1996 Ford Bronco/F150 and 1983-1996 F250 4x4 trucks with Dana 44 Twin Traction Beam® IFS front axles. More Info

$44.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40572 Ford Dana 44IFS Right Axle Shaft Slip Yoke Boot Is a genuine original equipment replacement Boot for all 1983.5-1996 Ford Bronco/F150 and 1983-1996 F250 4x4 trucks with Dana 44 Twin Traction Beam® IFS front axles that have the right inner axle shaft retained by a snap ring. More Info

$48.88
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40085 One Ear Stainless Steel Boot Clamp For the small end of QU40572 Slip Yoke Boot. More Info

$4.27
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40084 One Ear Stainless Steel Boot Clamp For the large end of QU40572 Slip Yoke Boot. More Info

$3.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40515 Right Differential Output Shaft Support Bearing For 1984-1996 Ford Dana 44IFS Front Axles. More Info

$14.73
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40226 Retaining Ring for Ford Dana 44, Dana 50 IFS Differential Output Shafts Is a genuine original equipment spring steel Snap Ring that fits in a groove on your innermost right axle shaft on 1984-1996 Ford Dana 44IFS and 1983.5-1997 Ford Dana 50 IFS Twin Traction Beam® front axles in full size Ford 4x4's. More Info

$4.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note

We offer two different Universal Joints for your hard working 1984 to 1996 4x4 Bronco or F-Series 4x4 Truck with a Dana 44 solid front axle. Both are good, reliable products, but different manufacturing techniques and seal types will have a major influence on the ultimate life of the joint. Our most popular choice is our TK40712 cold-forged, non-greaseable, original equipment replacement U-Joint. The wear-resistant cold-forged cross and superior sealing make it the best choice for both low maintenance and long life. QU90007 is hot-forged and is equipped with single lip seals. It is greaseable through a flush fitting threaded into one of the caps. With good maintenance and quality lubricant like our Pyroplex® Plus Grease, these joints will last and last.

photo

TK40712 Torque King® Premium Non-Greaseable Axle U-Joint For 1984-1996 Ford Dana 44IFS Front Axles Original equipment type universal joint with Premium Cold-Forged cross and superior pressure-type seals. More Info

$41.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90007 Greaseable Axle U-Joint With Rubber Seals for 1984-1996 Ford Dana 44IFS Front Axles Value priced with Hot-Forged cross and flexible rubber seals. More Info

$33.78
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ball Joints

top_page
product note

Ford used the same Ball Joints for all Dana 44IFS front axle applications in Bronco, F150, and F250 from 1980 to 1996, but different replaceable upper ball joint camber bushings were used depending upon the model, year, and suspension height.

photo

QA50095 Premium Greaseable Upper Ball Joint for all Ford Dana 44 IFS front axles. More Info

$65.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50222 Premium Greaseable Lower Ball Joint made for all Ford Dana 44 IFS front axles. More Info

$49.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40600 and QU50861 Fixed Camber Bushings For 1983.5-1996 Ford Dana Model 44 IFS front axle. More Info

Brake Parts

top_page
photo

QU20065 Disc Brake Caliper Pin For Bronco, F150, F250, F350 mid 1980's to mid 1990's. Genuine OEM Ford part. More Info

$5.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20447U Used F-250 Right Disc Brake Shield Fits all 1983-1996 Ford F250 4x4 trucks with 3800 pound rated Dana 44IFS Front Axles. Shield will have surface rust and may have some dings/dents, but this used right side disc brake rotor splash shield is in reasonably good condition and totally functional. More Info

$49.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20448U Used F-250 Left Disc Brake Shield Fits all 1983-1996 Ford F250 4x4 trucks with 3800 pound rated Dana 44IFS Front Axles. Shield will have surface rust and may have some dings/dents, but this used left side disc brake rotor splash shield is in reasonably good condition and totally functional. More Info

$49.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20619U Used Left Brake Shield for 1994-1996 Dana 44 Frod Bronco with ABS (Anti-Lock Brake System). Limited to availability. More Info

$50.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20620U Used Right Brake Shield for 1994-1996 Dana 44 Ford Bronco with ABS (Anti-Lock Brake System). Limited to availability. More Info

$50.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings (Individual)

top_page
product note

All 1984 to 1996 Ford Broncos and F-150/F-250 4x4 trucks with Dana 44 Independent Front Suspension Twin Traction Beam® Front Axles use the same differential and outer pinion bearings. The Inner Pinion Bearings changed during the 1992 model year, so if you have a 1992 model, you must verify which Inner Pinion Bearing and Cup your axle has.
All bearings are not created equal for fit or durability, so we only stock first class, long lasting, Timken® Differential and Pinion Bearings for your Dana front axle. Timken® was and is a a major original equipment supplier of top-notch bearing components to Dana Spicer. Since I first started rebuilding Dana axles in the mid 1970's, I have found Timken® Bearings to be the most consistent in relation to the published dimensions of any bearing on the market which makes rebuilding an axle right the first time a WHOLE lot easier!

photo

QU50533 Timken® Outer Pinion Bearing Cup For 1984-1996 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles. More Info

$9.32
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50534 Timken® Outer Pinion Bearing For 1984-1996 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles. More Info

$20.96
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50535 Timken® Early Inner Pinion Bearing Cup For 1984-1992.5 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles up to and including Axle Tag BOM Number 610335. More Info

$11.64
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50536 Timken® Early Inner Pinion Bearing For 1984-1992.5 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles up to and including Axle Tag BOM Number 610335. More Info

$26.22
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50539 Timken® Late Inner Pinion Bearing Cup For 1992.5-1996 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles with Axle Tag BOM Number 610407 or higher. More Info

$9.25
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50540 Timken® Late Inner Pinion Bearing For 1992.5-1996 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles with Axle Tag BOM Number 610407 or higher. More Info

$19.89
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50538 Timken® Differential Side Bearing For 1984-1996 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles. (uses 2) More Info

$17.72
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50537 Timken® Differential Side Bearing Cup For 1984-1996 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles. (uses 2) More Info

$12.36
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing and Seal Kits

top_page
product note

1983.5 to 1996 Ford Bronco, F150 1/2 ton truck, and F-250 3/4 ton trucks with Dana 44IFS Front Axles have part time transfer cases and lockout hubs. With a part time transfer case and lockout hubs, the axle shafts and differential parts do not rotate, so extreme diff/pinion bearing wear is rather rare except in work trucks. However, the flip side is water condensation in the diff has a tendency to cause rust and pitting of the bearings. If your vintage Ford has been used a lot in 4x4 mode or parked outside and subject to temperature changes, there is a good chance that significant wear or water damage may have occurred on your differential and pinion bearings. When you replace the bearings, do not forget to replace the two axle shaft oil seals.

photo

QU50576 1983.5-1992.5 Dana 44IFS Differential Bearing and Seal Kit For 1983.5-1992.5 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles features first class Timken® Differential and Pinion Bearings, plus Pinion Seal, Pinion Nut, Crush Sleeve, Gear Marking Compound, Threadlocker, and RTV Sealant. More Info

$149.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50595 1992.5-1996 Dana 44IFS Differential Bearing and Seal Kit For 1992.5-1996 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles features first class Timken® Differential and Pinion Bearings, plus Pinion Seal, Pinion Nut, Crush Sleeve, Gear Marking Compound, Threadlocker, and RTV Sealant. More Info

$149.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page

QU42084U Used Fast Ratio Loaded Differential for 3.00 to 3.73 ratio gear sets in 1984-1996 Ford Bronco, F150, and F250 4x4s. More Info

$95.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Makers

top_page
photo

S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential housing to the left axle beam on your Ford Dana 50 IFS Front Axle. More Info

$8.85
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hubs and Hub Parts

top_page
photo

QU20351 1984-1987 New Hub and Rotor Assembly with 1/2" Studs Fits all Dana 44 equipped 1983-1987 F250 4x4 trucks with the stock Dana 44IFS front axle and 1/2" diameter wheel studs. More Info

$299.01
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20348 1984-1992 F150, Bronco Splined Front Hub Is a brand new internally splined front wheel hub with studs that fits all 1983-1986, most 1987-1988 and all 1989-1992 Ford F150 and full size Bronco 4x4s. For the 1987 and 1988 model years, Ford used two types of 4x4 front hub and rotors. QU20348 fits all models with automatic hub-locks and those manual hub-lock trucks with internally splined wheel hubs. QU20348 does not fit 1987-1988 vehicles with external mount manual hubs that have a flange that gets sandwiched between the hub/rotor assembly and wheel. More Info

$132.57
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20349 1993-1994 F150, Bronco Splined Front Hub Is a brand new hub with studs specific to 1993 and 1994 F150 and full size Bronco. More Info

$140.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20352 New 8 Bolt Front Wheel Hub with 9/16" Studs for 1987-1994 Ford F250 with Dana 44 front axle.

Also available while supplies last: QU20352U Used Wheel Hub

More Info

$230.18
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20621 New Front Hub and Rotor Assembly for 1995-1996 Ford Bronco with 4 wheel ABS brakes.  Includes bearing cups and tone ring. More Info

$149.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20367U 1987-1988 Used Manual Hublock For 1987-1988 Ford Bronco and F150 with with "pancake" type front wheel hubs. More Info

$100.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56019 1 Side Warn Manual Hub Set More Info

$80.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU51181 Warn 20990 Premium Hub Set for Dana 44IFS Front Axles With internally splined front wheel hubs. Reliable and good looking. QU51181 Fits most Ford Dana 44IFS 1984-1996 F150 and F250 4x4s.

More Info

$129.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4918 Hub Service Kit For QU56018 Warn Manual Hub Set. More Info

$36.84
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20026 1987-1988 Hublock Retaining Clip For 1987-1988 Ford Bronco and F150 with flange mount Manual hublocks.These clips hold your flange type hublock against the wheel hub when you remove the wheels so that sealing o-ring between the hublock and wheel hub will maintain in contact with both.
More Info

$1.95
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56018 Warn Manual Hub Set For 1984-1996 Ford Bronco and F150 with internally splined wheel hubs. Also fits 1984-1988 F250 3/4 Ton 4x4s with Dana 44 front axles. More Info

$99.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20389U One Functional Used Dana Factory Lockout Hub and Red Dial fits 1984-1996 Ford F150 and F250 Dana 44IFS front axles with splined wheel hubs. Complete except for QU40035 Spring Plate which must be ordered separately. More Info

$75.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40427 Dana 44 Full Time Front End Hub Cap for 1984-1996 Ford F250 trucks with Dana 44IFS front axles. More Info

$19.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts

top_page
photo

QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound. More Info

$6.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals and Pinion Yokes

top_page
product note

1984-1996 Ford Dana 44IFS Front Axles use a Pinion Yoke made for the oversize 1.125" u-joint cups used on the Ford specific 1330F universal joints (See TK40723 and QU40776).

photo

QU20180 Ford Dana 44IFS Front Axle Pinion Yoke Is a genuine original equipment Ford Front Pinion Yoke for 1984-1996 Ford Bronco, F150, and F250 4x4s with Dana 44 IFS (IFS=Independent Front Suspension) Twin Traction Beam™ front drive axles. More Info

Also available while supplies last: QU20180U, QU40850B

$64.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40578 Pinion Seal for Ford Dana 44 Is a genuine Dana original equipment Pinion Seal for 1984-1996 Ford Bronco, F150, and F250 4x4s with Dana 44 IFS (IFS=Independent Front Suspension) Twin Traction Beam™ front drive axles. More Info

$15.16
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40841 Driveshaft U-Bolt Kit for Ford Dana 44 Front Axle Fits all 1984-1996 Ford original equipment type Front Dana 44IFS pinion yokes. More Info

$7.76
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
product note

The ring and pinion gear sets used in Ford Dana 44IFS front axles have a reverse cut or spiral compared to conventional Dana 44 gear sets. The engineering reason for this is the pinion gear in Ford Dana 44 axles is located above the axle center line. Reverse Spiral Gear Sets are NOT interchangeable with standard Dana 44 gear sets.

QU42013 4.09 Ratio Ford Dana 44 Reverse Spiral Ring and Pinion Kit is a genuine Dana Gear Set for Ford high pinion Dana 44IFS front axles in 1984-1996 Broncos, F150, and F250 4x4s. QU42013 includes a matched, reverse cut Dana ring and pinion set, pinion bearings with cups, pinion seal, pinion nut, pinion washer, pinion slingers, pinion shims, differential shims, and ring gear bolts. More Info

Also available while supplies last: QU42012U Used 4.09 Ratio Reverse Spiral Ring and Pinion Gear Set

$453.85
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20509U Used 3.54 Ratio Ford Dana 44 Reverse Spiral Ring and Pinion Set is a good used, revers spiral Dana Gear Set for Ford high pinion Dana 44IFS front axles in 1984-1996 Broncos, F150, and F250 4x4s. QU42013 includes a matched 46 tooth ring gear and 13 tooth pinion gear. More Info

$90.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
photo

QU20078 Half-Moon Axle Shaft Snap Ring For 1986-1996 Ford Bronco, F150, and Dana 44 IFS front axle equipped F-250 4x4 trucks with factory automatic hubs. These C-Type Snap Rings fit a groove in the outer axle shaft just and retain the spline thrust washer (QU20077 or QU40079). More Info

$14.15
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20077 3 Piece Axle Shaft Thrust Washer Set For 1993-1996 Ford Bronco and F150. Set includes 19 Spline Steel Washer, Steel Thrust Washer, and Synthetic Thrust Washer. More Info

$22.51
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40079 19 Spline Thrust Washer For 1986-1992 Ford Bronco, F150, and Dana 44 IFS front axle equipped F-250 4x4 trucks with factory Automatic Locking Hubs. This steel Thrust Washer fits over the outer axle shaft and fits against the end of the spindle. More Info

$39.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU50861 0 Degree Camber Bushing for Ford Dana model 44 IFS front axles. More Info

$29.47
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindles and Spindle Nuts

top_page
product note

Ford used four different Spindle Nut configurations in 1983.5-1996 era. Axles with Double Spindle Nuts used the same Inner and Outer Nuts, but different Lock Washer depending upon if the axle was equipped with manual or auto hubs. A single, Ratchet Type Spindle Nut was used for most 1985-1992 manual hub applications after which Ford again used a Double Spindle Nut Set for manual hubs through 1996. In late 1992 or early 1993, Ford introduced a new automatic hub that uses a single, unique, stepped, rounded hex nut that is only compatible with auto hubs. The auto hubs proved to be somewhat finicky, so by now, most 1995-1996 era auto hubs have been replaced with manual hubs and Double Spindle Nut Sets.

photo

QK4727 1983-1996 3 Piece Front Spindle Nut and Washer Kit for Manual Hubs Fits 1983.5-1996 Ford Bronco, F100, F150 and F250 4x4 Trucks with Dana 44IFS front axles equipped with manual hub-locks. QK4727 Kit includes these genuine Dana original equipment parts: QU40004 Inner Spindle Nut, QU40060 Round Spindle Lockwasher, and QU40031 Outer Spindle Nut. More Info

$19.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4770 1983-1992 Front 4x4 Auto Hub Spindle Nut and Washer Set Includes genuine original equipment parts for 1983.5-1992 Ford Bronco, F100, F150 and F250 4x4 Trucks with Dana 44IFS front axles equipped with auto hub-locks. QK4770 Kit includes these genuine Dana original equipment parts: QU40004 Inner Spindle Nut, QU40429 Tabbed Spindle Lockwasher, and QU40031 Outer Spindle Nut. More Info

$41.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40004 Inner Spindle Nut For all 1983.5-1996 Ford Bronco, F100, F150, F250 4x4 Trucks with Dana 44IFS front axles equipped with manual hub-locks. Also fits Also fits 1983.5-1992 models with factory auto hubs. QU40004 threads on the spindle and fits against your outer wheel bearing to provide correct wheel bearing end-play. More Info

$15.96
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40060 Round Spindle Lock Washer For all 1983.5-1996 Ford Bronco, F100, F150, F250 4x4 Trucks with Dana 44IFS front axles equipped with manual hub-locks. QU40060 locks your QU40004 Inner Spindle Nut in position when properly installed. More Info

$3.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40429 Tabbed Spindle Lock Washer Is a genuine original equipment part for 1983.5-1992 Ford Dana 44IFS front drive axles with auto hubs. The four external tabs on this part act as anchor points for your auto hub inner body. QU40429 can also be used to replace QU40060 Round Spindle Nut on manual hub applications. More Info

$14.01
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40031 Outer Spindle Nut For all 1983.5-1996 Ford Bronco, F100, F150, F250 4x4 Trucks with Dana 44IFS front axles equipped with manual hub-locks. Also fits Also fits 1983.5-1992 models with factory auto hubs. More Info

$14.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40106 1985-1992 Rachet Type Spindle Nut Is a genuine Dana replacement part for 1985-1992 Ford Dana 44 Front Axles with manual hub-locks that use a single spindle nut. More Info

$29.89
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40309/Y440309/QU20510U Spindle for 1983.5-1992 Bronco and F150 with Internal Spline Wheel Hubs Is a Spindle Kit for 1983.5-1986 and 1989-1992 Ford 4x4 Broncos and F150 trucks. QU40309/Y440309 also fits 1987-1988 Bronco and F150 with internally splined wheel hubs. New Spindles include needle bearing, two v-seals, and axle shaft thrust washer. More Info

photo

QU42005/Y442005/QU42023U Spindle for 1983.5-1992 F250 with Dana 44IFS Front Axle Spindle Kit for 1983.5-1992 Ford F-250 4x4 trucks with 3800/3850 pound rated Dana 44 front axles. New Spindles come with needle bearing, two v-seals, and axle shaft thrust washer. More Info

Y450000 Replacement Front Spindle for 1993-1996 Ford Dana 44IFS front axles without ABS.

More Info

$210.30
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Y450001 Replacement Front Spindle for 1994-1996 Ford Dana 44IFS, 5 holes w/ ABS sensor holes.

Note: If you have Bill of Materials number 610446, your differential uses spindle number 75303X, which has been discontinued.

More Info

$218.05
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Bearings and Seals

top_page
product note

The dead, hollow spindle design of the 1983.5-1996 era Ford Dana 44 IFS axles uses one QK4734.5 needle bearing to support the outer axle shaft. Ford used two different Spindle Seal types for 1983.5-1996 Dana 44IFS Front Axles. A two part Spindle Seal and Thrust Washer design was new for 1993, replacing the earlier four piece set-up used on most trucks from 1983.5-1992. Personally, I prefer the older Seal design which can be retrofitted to 1993-1996 trucks if you order (2) QU40058 Slingers and (1) QK4739 Seal and Thrust Washer Set.

photo

QK4734 Front Axle Shaft Spindle Bearing Set Fits all 1983.5-1996 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles. One bearing is pressed into each spindle to support the outer axle shaft. More Info

$25.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40056 1983.5-1992 Small Spindle to Axle Shaft V-Seal Is a genuine original equipment 1-5/16" ID Rubber V-Seal that is installed in your spindle between QK4734.5 Spindle Bearing and QU40070 Spindle Thrust Washer. Fits 1983.5-1992 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles. More Info

$7.15
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40070 1983.5-1992 Axle Shaft to Spindle Thrust Washer Is a genuine original equipment plastic thrust washer that controls axial thrust between your outer axle shaft and spindle. Fits 1983.5-1996 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles. More Info

$4.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40071 1983.5-1992 Large Axle Shaft to Spindle V-Seal Is a genuine original equipment 2.25" ID Rubber V-Seal that seals between your axle shaft and spindle. Fits 1983.5-1992 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles. More Info

$11.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4739 1983.5-1992 Spindle Seal Kit Services both sides on your 1983.5-1992 Ford Bronco or Ford F-150/F-250 4x4 truck with Dana 44IFS Twin Traction Beam® front axle. More Info

$45.78
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40228 1983.5-1992 Spindle Bearing and Seal Kit Services one side on your 1983.5-1992 Ford Bronco or Ford F-150/F-250 4x4 truck with Dana 44IFS Twin Traction Beam® front axle. More Info

$19.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40058 1983.5-1992 Outer Axle Shaft Slinger Acts as both as a crud deflector and a sealing surface on open knuckle axles. Replace anytime they are dinged, bent or badly corroded. Fits 1983.5-1992 Ford Bronco and Ford F-150/F-250 4x4 trucks with Dana 44IFS Twin Traction Beam® front axles. More Info

$6.68
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40436 1993-1996 Bronco and F-150 Outer Axle Shaft/Spindle Seal and Bearing Set Has the genuine original equipment axle support bearing and spindle seals needed to service ONE side.

More Info

$29.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40459 1993-1996 Press On Axle Shaft to Spindle Seal Is a genuine original equipment seal that is installed on your outer axle shaft. Fits 1993 to 1996 Ford Bronco and F-150 Dana 44 Independent Front Suspension (IFS) front axles.

More Info

$11.28
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40439 Spindle Bearing and Seal Kit for 1984-1992 Ford F150 and full size Bronco Dana 44 front axles with unitized spindle seal and thrust washer. Services 1 spindle.

More Info

$29.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Knuckles

top_page

QU20445U Used Left Steering Knuckle for 1984.5-1994 Ford F250 with Dana 44IFS Front Axle.
More Info

$125.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20446U Used Right Steering Knuckle for 1984.5-1994 Ford F250 with Dana 44IFS front axle.
More Info

$125.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20513U Used Right Bronco and F150 Steering Knuckle for 1984-1985.5 Ford Bronco and F150 is a good used right or passenger side Steering Knuckle for all 1984-1985.5 Ford Bronco and F150 4x4s. This is correct Knuckle for your Ford if your brake caliper is retained by a drive in key topped by an arched, flat cross-section spring. More Info

$75.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20514U Used Left Bronco and F150 Steering Knuckle for 1980-1985.5 Ford Bronco and F150 is a good used left or driver's side Steering Knuckle for all 1980-1985.5 Ford Bronco and F150 4x4s. This is correct Knuckle for your Ford if your brake caliper is retained by a drive in key topped by an arched, flat cross-section spring. More Info

$75.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 44IFS front axle in your 1980-198.5 Bronco, F-150, or F250.

photo

QT1044 Inner Pinion Bearing Installer For Dana 44IFS front axles in 1983.5-1996 Ford Bronco, F-150, or F-250 4x4 trucks. More Info

$31.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1115 Dana 44 Differential Side Bearing Installer For Dana-Spicer Model 44 front 4x4 front axles. QT1115 features a raised internal ring that contacts the bearing inner face so you can press or drive your diff bearings on without damaging the cage. More Info

$34.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1812 Outer Pinion Bearing Cup Installer Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50533 Outer Pinion Bearing Cup a simple and fast procedure. More Info

$19.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers. More Info

$19.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1803 Inner Front Wheel Bearing Cup Installer for Bronco, F150 For Dana 44IFS front axles in 1983.5-1996 Ford Bronco and F-150 4x4s with internally splined front wheel hubs. QT1803 does NOT fit 1987-1988.5 Bronco and F150 with manual hubs and pancake style hub and rotor assembly or any F250. More Info

$24.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1801 Inner Wheel Bearing Cup Installer for F250 and Inner or Outer Wheel Bearing Cup Installer for some 87-88.5 Bronco, F150 4x4s QT1801 is used to install the inner wheel bearing cup for a Dana 44IFS equipped F250 4x4s AND to install both the inner and outer wheel bearing cups on 1987-1988.5 Ford Bronco and F150 4x4s with factory manual hubs and 1 piece cast "pancake" style unsplined wheel hub and rotor assemblies. More Info

$23.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1802 Outer Front Wheel Bearing Cup Installer For most Dana 44IFS front axles in 1983.5-1996 Ford Bronco, F-150, or 1983.5-1996 F-250 4x4 trucks. This installer works for the outer wheel bearing cup on all years/models EXCEPT: 1987-1988.5 Bronco and F150 with manual hubs and pancake style hub and rotor assembly. More Info

$25.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1502 1983.5-1996 Wheel Seal Installer For Dana 44IFS front axles in 1983.5-1994 Ford Bronco, F-150, or 1983.5-1996 F-250 4x4 trucks. More Info

$26.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1012i 4 Lug Spindle Nut Socket For manual hub equipped Dana 44IFS front axles in 1983.5-1996 Ford Bronco, F-150, or 1983.5-1996 F-250 4x4 trucks. More Info

$16.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT5500 Wheel Bearing Packer Takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your Ford 4x4! More Info

$33.53
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals (Individual)

top_page
product note

For F250, 1983.5-1986 and 1989-1994 F150/Bronco all use the same wheel seal and outer wheel bearing part numbers. 1987-1988.5 Bronco and F150 with manual hubs have a unique wheel bearing/seal setup. Almost all 1995-1996 Ford F150 and Broncos use a different wheel seal. The seal change was necessary to provide clearance for the ABS Brake Tone Ring. However, My Ford parts books do list 1995, 1996 U150 (Bronco) with a 3.07 gear ratio and manual hubs that does use QU90007 seal. I never saw one and Dana does not show a Bill of Material list for this axle, but presumably Ford did build some 1995-1996 Broncos with the older wheel hub/seal design for fleet use or no-frills buyers.

photo

QU50447 1983.5-1996 F-250 Timken® Outer Wheel Bearing Cup For all Dana 44IFS front axles in 1983.5-1996 F-250 4x4 trucks. More Info

$6.40
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50448 1983.5-1996 F-250 Timken® Outer Wheel Bearing For all Dana 44IFS front axles in 1983.5-1996 F-250 4x4 trucks. More Info

$13.77
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50446 1983.5-1996 F-250 Timken® Inner Wheel Bearing Cup For all Dana 44IFS front axles in 1983.5-1996 F-250 4x4 trucks. More Info

$9.46
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50412 Timken® Inner Wheel Bearing For all Dana 44IFS front axles in 1983.5-1996 F-250 4x4 trucks. Also, two of these bearings are used for each front wheel hub on 1987-1988.5 Ford Bronco and F-150 4x4 trucks with factory manual hubs and one-piece "pancake" style hub and rotor assemblies. More Info

$14.46
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50411 Timken® Inner or Outer Wheel Bearing Cup for 1987-1988 Bronco or F150 with 1 Piece Wheel Hub Two of these bearing cups are used for each front wheel hub on 1987-1988.5 Ford Bronco and F-150 4x4 trucks with factory manual hubs and one-piece "pancake" style hub and rotor assemblies. More Info

$8.15
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50577 Timken® Inner Wheel Bearing Cup For Dana 44IFS front axles in most 1983.5-1996 Ford Bronco and F-150 4x4 trucks EXCEPT: 1987-1988.5 Bronco and F150 with manual hubs and pancake style hub and rotor assembly. More Info

$9.11
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50578 Timken® Inner Wheel Bearing For Dana 44IFS front axles in most 1983.5-1996 Ford Bronco and F-150 4x4 trucks EXCEPT: 1987-1988.5 Bronco and F150 with manual hubs and pancake style hub and rotor assembly. More Info

$13.91
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU50166 Front Wheel Seal for some 1987-1988.5 Ford Bronco and F150 Front axles is a high-quality oil and grease seal with a garter spring plus an outer wiper lip that ONLY fits 1987-1988.5 Bronco/F150 with manual hubs and pancake style one-piece hub and rotor. More Info

$12.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20403 Front Wheel Seal for most 1995-1996 Ford Dana 44IFS Front axles is a high-quality oil and grease seal specific to 1995 and 1996 Bronco or F150 4x4s with front ABS tone rings. More Info

$24.64
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90001 1983.5-1996 F-250 Front Wheel Seal for Ford Dana 44IFS Front axles is a high-quality oil and grease seal with a garter spring plus an outer wiper lip that fits 1983.5-1996 4x4 Ford F250 Dana 44IFS front axles. More Info

$8.27
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
product note

It is always good preventative maintenance to replace all the front wheel bearings and seals when restoring or maintaining your vintage Bronco, F150, or F250. The parts availability for decades old 4x4s declines on a daily basis. Wrecking a wheel hub and/or spindle when the old bearing you reused fails can either cost you a mint or put your broken-down truck on blocks forever. We feature Timken® Bearings in our high quality Front Wheel Bearing and Seal Kits which are available with or without tools to keep your big Ford rolling.

photo

TK4711 Torque King® Master Front Wheel Bearing Kits with Tools for 1983-1994 Ford Dana 44IFS Bronco and F150 Fit 1983-1994 F150, and Broncos with Dana 44IFS open knuckle front axles and internally splined front wheel hubs. This Kit will NOT fit 1987-1988 vehicles with pancake style front wheel hubs! Includes 4 Timken® Bearings with Bearing Cups, 2 Wheel Seals, Bearing Cup Installers, Wheel Seal Installer and Driver Handle. More Info

$189.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4780 Torque King® Front Wheel Bearing Parts Only Kits for 1983-1994 Ford Dana 44IFS Bronco and F150 Fit 1983-1994 F150, and Broncos with Dana 44IFS open knuckle front axles and internally splined front wheel hubs. This Kit will NOT fit 1987-1988 vehicles with pancake style front wheel hubs! More Info

$98.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4905 Torque King® Front Wheel Bearing Only Kits for 1983-1994 Ford Dana 44IFS Bronco and F150 Fit 1983-1994 F150, and Broncos with Dana 44IFS open knuckle front axles and internally splined front wheel hubs. This Kit will NOT fit 1987-1988 vehicles with pancake style front wheel hubs! Includes 4 Timken® Bearings with Bearing Cups. More Info

$83.90
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK4761 Torque King® Front Wheel Bearing and Seal Kits for SOME 1987-1988.5 Ford Bronco and F150 4x4s Fits 1987-1988.5 Bronco, F150 4x4s with factory manual hubs and unsplined 1-piece pancake style front wheel hubs! Includes 4 Timken® Bearings with Bearing Cups and 2 Wheel Seals. More Info

$106.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4915 Torque King® Front Wheel Bearing Only Kits for SOME 1987-1988.5 Ford Bronco and F150 4x4s Fits 1987-1988.5 Bronco, F150 4x4s with factory manual hubs and unsplined 1-piece pancake style front wheel hubs! Includes 4 Timken® Bearings with Bearing Cups. More Info

$82.33
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK4937 Torque King® Front Wheel Bearing and Seal Kits for MOST 1995-1996 Ford Bronco and F150 4x4s Fits 1995-1996 Bronco, F150 4x4s with 4 wheel Anti-Lock Brake systems. Includes 4 Timken® Bearings with Bearing Cups and 2 Wheel Seals. More Info

$125.34
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4905 Torque King® Front Wheel Bearing Only Kits for MOST 1995-1996 Ford Bronco and F150 4x4s Fits 1995-1996 Bronco, F150 4x4s with 4 wheel Anti-Lock Brake systems. Includes 4 Timken® Bearings with Bearing Cups. More Info

$83.90
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK4751 1983-1996 Torque King® F250 Master Front Wheel Bearing Kits with Tools for Ford F250 Dana 44IFS Front Axles These Kits fit 1983 to 1996 Ford F-250 4x4s with 3800 or 3850 pound rated Dana 44IFS front axles. Do the job right the first time with premium quality parts and installation tools custom made for the job. Includes 4 Timken® Bearings with Bearing Cups, 2 Wheel Seals, Bearing Cup Installers, Wheel Seal Installer and Driver Handle. More Info

$194.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4752 1983-1996 Torque King® F250 Front Wheel Bearing Parts Kits for Ford F250 Dana 44IFS Front Axles These Kits fit 1983 to 1996 Ford F-250 4x4s with 3800 or 3850 pound rated Dana 44IFS front axles. Do the job right the first time with premium quality parts. Includes 4 Timken® Bearings with Bearing Cups and 2 Wheel Seals. More Info

$101.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4894 1983-1996 Torque King® F250 Front Wheel Bearing Only Kits for Ford F250 Dana 44IFS Front Axles These Kits fit 1983 to 1996 Ford F-250 4x4s with 3800 or 3850 pound rated Dana 44IFS front axles. Do the job right the first time with premium quality parts. Includes 4 Timken® Bearings with Bearing Cups. More Info

$83.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Discontinued Parts

top_page
photo

QU40171 Original Equipment Dana 44 IFS Ball Joint Set For all Ford Dana 44 IFS front axles includes these Dana original equipment parts: one non-greaseable upper ball joint with nut, one non-greaseable lower ball joint with nut, one snap ring, one offset camber bushing, and one cotter key. Discontinued.

photo

QU20345 1987-1994 F250 Hub and Rotor with 9/16" Studs Is a brand new genuine ford OE hub and rotor assembly with 9/16" studs is specific to 1987-1994, but will fit 1980-1986. Superseded to QU20352.

photo

QU20350 1995-1996 F150, Bronco Hub Is a brand new Splined Front Hub with studs specific to 1995 and 1996 F150 and full size Bronco with 4 wheel ABS brakes. Superseded to QU20621.

Discontinued Tools

top_page
photo

QT1815 Inner Pinion Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50539 Inner Pinion Bearing Cup a simple and fast procedure. Superseded by QT1812.

photo

QT1097 Differential Master Bearings Slip on your differential in place of the taper bearings and cups. Used along with a dial indicator to determine the correct differential shim thickness. Discontinued.