Parts for Dana-Spicer Model 50 IFS Front Axles in 1980-1982 Ford F-250, F-350 4x4 Trucks

We stock a good selection of replacement parts for 1980 to 1982 Ford F-250 and Ford F350 4x4 trucks with Dana Spicer Model 50 Independent Front Suspension (IFS) Twin Traction Beam® drive axles. Introduced for 1980 model year as an option for the F250 and standard on the F350, the Ford IFS Twin Traction Beam® Dana 50 axle replaced the previous solid beam Dana 60 axle used in 1978 and 1979. The Dana 50IFS axle underwent a significant redesign for the differential and right side differential output shaft after the 1982 model year.

Axle Identification

top_page
product note

Ford was the only vehicle manufacturer to use Dana Twin Traction Beam® Independent Front Suspension Axles which can be found on 1980-1997 model year Ford 4x4s. The Twin Traction Beam® IFS Axle line includes the coil spring Models 28 and 35 found in Bronco II, Explorers and Ranger pickups, the Model 44 which was used in fill size Broncos, F-150 (coil springs), and light duty F-250 pickups (leaf springs), and the leaf sprung 4500 to 4600 pound rated Model 50IFS axle in heavy GVW F-250 and 1980-1985.5 F-350 trucks.

photo

Hub Size: Ford used both Dana 44 and Dana 50 IFS Twin Traction Beam® Front Axles in F-250 trucks. The easiest way to tell them apart is by measuring the diameter of the wheel hub or locking hub. Dana 44 axles have hubs that are approximately 3-3/8" in diameter. Dana 50 Hubs are about 4-1/8" in diameter.

Right Differential Output Shaft: The major difference between 1980-1983.5 and 1983.5-1997 Ford Dana 50IFS front axles is the way the right differential output shaft is supported and retained. The early axles use a pressed-on taper roller bearing and an external bolt-on retaining flange. Later production axles use a straight roller bearing pressed into the differential housing and the axle shaft is retained by a snap ring inside the differential next to the differential side gear. The early right diff output shafts could be pulled without removing the differential housing from the axle beam with a special slide hammer puller attachment, but seal replacement also requires the bearing be replaced. For later axles, you MUST remove the differential housing from the axle beam to access the snap ring, but once it is out replacing the right seal is quick and easy.

Suspension: Leaf spring

Knuckle Mounting: Ball Joints

Wheel Hub: 1980-1983.5 Ford Model 50 axles have an internally splined hub in which a splined lockout hub assembly would fits into.

Axle Assemblies and Axle Housings

top_page
product note

Dana 50IFS front axle beams were pretty much unchanged over the entire production life of the axle with one minor exception. Very early production differential housings used two 3/8" bolts to attach the differential housing to the reinforcement plate on the left beam. The bolt size was increased to 1/2" in late 1980 or 1981 so the two plate holes in the axle beam were larger for all subsequent axles. I recommend you replace the Axle Beam Pivot Bushing before installing one of these Used Axle Beams.

photo

QU20280U Left Ford Dana 50IFS Axle Beam Is a good used drivers side bare Axle Beam for 1980-1982 F250 and F350 4x4s with Dana 50IFS front axles. More Info

N/A
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20281U Right Ford Dana 50IFS Axle Beam Is a good used passenger side bare Axle Beam for 1980-1982 F250 and F350 4x4s with Dana 50IFS front axles. More Info

$139.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50097 Axle Beam Pivot Bushing Fits either left or right axle beams. One of these Bushings gets pressed into the inboard end of each axle beam. More Info

$22.62
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20246U-2 Differential Bearing Caps for Ford Dana 50 Axles Differential Bearing Caps are line bored for each axle and considered non-interchangeable. However, if you do not have a differential case spreader with Dana 50 IFS adapters, you can use an extra pair of caps to seat the differential, then remove them and replace with the original caps. More Info

$20.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shafts

top_page
product note

We still have brand new left and right Axle Shafts in stock for 1980-1982 Ford 4x4s with Dana 50 IFS Front Axle. Production on these shafts ended years ago, so when our current limited inventory is exhausted that will be the end of new assemblies. Our available used axle shaft inventory is also limited due to the Cash for Clunkers program and high scrap prices which has sent large numbers of Fords with Dana 50 axles straight to the crusher.

photo

QK4773/QK4773R Left Axle Shaft Assembly with Torque King U-Joint For all 1980 to 1982 Ford F-250 and F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle. QK4774 is an all new left axle shaft assembly. QK4774R is a reconditioned assembly that includes good used axle shafts and a new TK40719 Torque King® Cold Forged U-joint. More Info

photo

QK4774/QK4774R Right Axle Shaft Assembly with Torque King U-Joint For all 1980 to 1982 Ford F-250 and F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle. QK4774 is an all new right axle shaft assembly. QK4774R is a reconditioned assembly that includes good used axle shafts and a new TK40719 Torque King® Cold Forged U-joint. More Info

photo

QU40435 New Right Axle Inner Shaft For all 1980 to 1982 Ford F-250 and F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle. More Info

$199.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40824 New Left Axle Inner Shaft For all 1980 to 1982 Ford F-250 and F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle. More Info

$276.39
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20402 Right Differential Output Shaft Assembly For 1980-1982 Ford Dana 50IFS Front Axle is a genuine Dana OEM assembly that includes the right differential output shaft with support bearing and seal, u-joint and slip yoke. More Info

$195.01
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40815 Ford Shaft Slip Yoke For 1983-1997 Ford Dana 50 IFS right side axle. More Info

$160.01
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20079 Ford Outer Axle Shaft Is a brand new, genuine Dana original equipment axle shaft for all 1980 to 1982 Ford F-250 and F-350 4x4 trucks with Dana 50IFS front axles. More Info

$149.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20374U Used Ford Outer Axle Shaft Is a good used, genuine Dana original equipment axle shaft for 1980-1982 Ford F250/F350 4x4 trucks with Dana 50IFS front axles. These low cost Axles have 1 snap ring groove at the outboard end so they are not suitable for later model trucks with hublocks that use an inboard snap ring. More Info

$99.49
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Bearing, Seals and Seal Kits for Inner Axle Shafts

top_page
product note

The original Ford Dana 50IFS Front Axle uses a combination guide and seal for the Left Axle Shaft Seal and a conventional seal sandwiched between the axle support bearing and axle thrust plate on the right side.

photo

QK4035 1980-1983 Ford Dana 50IFS Right Axle Shaft Bearing and Seal Kit with Lock Ring for 1980-1983 Ford Dana 50 IFS Front Axles with bolt in right side differential output shafts. QK4035 includes the axle shaft seal, axle shaft bearing, and bearing lock collar. Kit contains both USA and import parts.  Replaces QU40173 which is NLA. More Info

$39.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40087 Left Ford Dana 50 IFS Differential to Axle Shaft Seal Fits all 1980-1982 Ford F-250 and F-350 4x4 trucks with 1st design Dana 50 Twin Traction Beam® IFS front axles. More Info

$6.58
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42109 Timken® Axle Shaft Bearing with Lock Ring for 1980-1982 Ford Dana 50 Twin Traction Beam IFS with bolt in right side differential output shafts. More Info

$30.13
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42110 Right Differential Output or Axle Shaft Seal for 1980-1983 Ford Dana 50IFS front axles with bolt in axle shaft. Also used on some semi-float rear axle shafts. More Info

$12.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note

The Dana 50 IFS axle has 3 axle universal joints, one for the left side and two for the right side. For the Dana 50, we offer QK4874 Greaseable U-joint as an inexpensive alternative to our QU40470 solid cross original equipment, non-greaseable u-joint which is our as our maximum strength option for these axles. QK4874 Greaseable U-joint is a whole lot cheaper compared to QU40470, but there is some strength loss since it is cross-drilled for grease passage.

photo

QK4874 Greaseable External Snap Ring Axle Universal Joint for 1980-1983 Ford Dana 50 Front Axles In 4x4 F-250 and F-350 trucks with Dana 50IFS Twin Traction Beam® IFS front axles. More Info

$25.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ball Joints

top_page
product note

Ford Dana 50IFS Front Axles use a unique Ball Joint that was not used on any other application. The original, non-greaseable Ball Joints are no longer available through Dana, but we do a have premium greaseable Ball Joints available for you big Ford either individually or in a complete set of 4 Ball Joints. To press your Ball Joints in or out of the steering knuckles, see TS4511 Ball Joint Press Set which also works on Dana 60 axles

photo

QK4561 Greaseable Ball Joint Kit for Ford Dana 50IFS Front Axles Includes 2 upper and 2 lower Greaseable Ball Joints with hardware for all 1980-1982 Ford F-250 and F-350 4x4 trucks with Dana 50 4600 lb. front axles. Photo to be updated. More Info

$231.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QA50095 Greaseable Upper Ball Joint with hardware for 1980-1982 Ford Dana 50 IFS Front Axles. More Info

$65.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50056 Greaseable Lower Ball Joint with hardware for 1980-1982 Ford Dana 50 IFS Front Axles. More Info

$49.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
photo

QU20284 1980-1982 Left Front Brake Splash Shield for 1980-1982 Ford F250 and 1980-1982 F350 with Dana 50IFS 4600 pound front axles. More Info
Also available while supplies last: QU20284U Used Brake Splash Shield

photo

QU20285 1980-1982 Right Front Brake Splash Shield for 1980-1982 Ford F250 and 1980-1982 F350 with Dana 50IFS 4600 pound front axles. More Info
Also available while supplies last: QU20285U Used Brake Splash Shield

photo

QU20054 Front Disc Brake Caliper Tension Spring For 1980-1982 Ford F250, F350 Dana 50IFS front axle with dual piston calipers. More Info

$4.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU80002 Caliper Slide Lock Bolt Is a special, hex head bolt that threads into the caliper anchor plate on your disc brake equipped 1980-1982 Ford F250, F350 Dana 50IFS front axle with dual piston calipers. The tapered body between the threads and end fits into the inner notch of the caliper slide or key. QU80002 is plated for corrosion resistance. More Info

$4.96
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings (Individual)

top_page
photo

QU40002 Outer Pinion Bearing Slinger More Info

$3.60
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing and Seal Kits

top_page
product note

All 1980-2005 Ford Dana 50 front axles have the same differential and pinion bearings. The pinion seals and method to set pinion preload vary by year. We offer two Kits with Timken Bearings. TK4885 includes JUST the diff and pinion bearings/cups, you can then individually order the exact extra original equipment parts you need for your specific axle. QU50581 is a "universal" Kit for all Dana 50 axles that has the same premium Timken bearings as TK4885 plus aftermarket small parts and 2 pinion seals.

photo

TK4885 Torque King® Dana 50 Differential and Pinion Bearing Only Kit For all Ford Dana 50 Twin Traction Beam IFS Front Axles in F250/F350 4x4 trucks. Kit includes Timken® Pinion and Differential Bearings with Bearing Cups. TK4885 includes just the bearings, order your seals, shims, and other small parts as needed from our complete selection of genuine Dana original equipment replacement components. More Info

$124.01
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50581 Differential Bearing and Seal Kit For all Ford Dana 50 Twin Traction Beam IFS Front Axles in F250/F350 4x4 trucks. Kit includes Timken® Pinion and Differential Bearings with Cups, plus aftermarket replacement pinion seals, pinion nut, pinion preload shims, and crush sleeve. Also includes RTV sealant, threadlocker, gear marking compound and brush. More Info

$183.35
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
product note

The Dana 50 axle is unusual in that no other vehicle manufacturer besides Ford ever used it for any application. This means Ford has a lock on the distribution and pricing of most new Dana 50 specific internal parts. Due to the advancing age of Dana 50 equipped vehicles, many Dana 50 differential parts are no longer available from Ford. However, we do have some new small parts and good used major parts for the Ford Dana 50 axle.

photo

QU40519 Differential Cross Shaft Lock Pin Is a genuine Dana original equipment Roll Pin used to secure your differential cross shaft to the diff case on 1980-1982 Ford F-250 and F-350 4x4 trucks with Dana 50IFS Front Axles. More Info

$2.89
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40576 Dana 50IFS Pinion and Differential Shim Kit For 1980-1982 Ford F-250 and F-350 4x4 trucks includes these genuine Dana parts: Pinion Depth Shims, Pinion Preload Shims, Differential Adjusting Shims, Pinion Nut and Pinion Washer. (Kit also has an Inner Axle Shaft Snap Ring which is not used on these years.) More Info

$52.05
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20239 OEM Ford Dana 50 Internal Differential Parts Kit Fits 1980-1982 Ford F-250 and F-350 4x4 trucks with Dana 50IFS Front Axles. These are brand new, genuine original equipment internal diff gear sets for 3.73, 4.10, and 4.30 ratio Ford Dana 50 front axles. More Info

$249.20
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20240U Good Used Loaded Differential Case QU20240U Good Used Loaded Differential Case fits 1980-1982 Ford F-250 and F-350 4x4 trucks with Dana 50IFS Front Axles. These are good used loaded Diff Cases with internal gears for 3.73, 4.10, and 4.30 ratio Ford Dana 50 front axles. More Info

photo

QU20401 Differential Cross Shaft for 1980-2005 Ford F250, F350, or Excursion with Dana 50IFS or Dana 50 Beam axles. More Info

$49.51
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hubs and Hub Parts

top_page
product note

There were two different Hub and Rotors for 1980-1982 Ford F-250 and F-350 trucks with Dana 50IFS axles. We also stock parts for the Red plastic Dial Warn manual hubs used on factory manual hub equipped 1980 to 1982. Mechanically, this is the same Warn hub as the sold by the aftermarket with a black plastic dial for the 1980-1982 model years.

photo

QU20224 Hub and Rotor for 1980-1982 Ford Dana-Spicer Model 50IFS Front Axles with single rear wheels and 1/2" wheel Studs. More Info

$366.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TKA20332 Wheel Hub for 1980-1982 Ford Dana-Spicer Model 50IFS Front Axles with single rear wheels. More Info
Also available while supplies last: QU20332U Used Wheel Hub

$289.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42116 30 Spline Drive Gear Kit for 1980-1982 Ford Dana 50IFS Front Axles with internal splined wheel hubs. More Info

$318.40
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56025 Warn 38826 Premium Hub Set for Dana 50IFS Front Axles With internally splined front wheel hubs. A sharp looking and reliable hub. QU56025 Fits Ford Dana 50IFS 1980-1982. More Info

$269.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56011 Spline Mount Lockout Hub Set For 1980-1982 Ford Dana-Spicer Model 50IFS front drive axles and internally splined wheel hubs. QU56011 is the current production version of the Warn's original equipment 1980-1994 Ford Hub-Lock. More Info

$234.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4916 Hub Service Kit For QU56011 Lockout Hubs includes 2 QU56017 Spiral Retaining Rings, 2 QU56016 O-Rings, 2 QU40068 Axle Shaft Snap Rings, 12 QU56012 Hub Screws, and 1 Set Replacement Decals. More Info

$42.88
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50116 QUAD-Ring square cross section sealing ring For Factory Warn® Spline Mount Hubs in 1980-1982 Ford F-250, F-350 Dana 50IFS Front Axles. More Info

$3.91
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50240 O-Ring For Warn® Spline Mount Hub Dials in 1980-1982 Ford F-250, F-350 Dana 50IFS Front Axles. More Info

$1.78
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40068 Axle Shaft Snap Ring Fits in the groove machined at the end of the outer axle shaft splines in 1980-1982 Ford F-250, F-350 Dana 50IFS Front Axles. More Info

$12.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40150 Lockout Hub to Wheel Hub Snap Ring For Warn® Spline Mount Hubs used in 1980-1982 Ford F-250, F-350 Dana 50IFS Front Axles. More Info

$19.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56013 Warn® Dial Assembly For Original Equipment Spline Mount Hubs used in 1980-1982 Ford F-250, F-350 Dana 50IFS Front Axles. More Info

$119.01
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56017 Warn® Spiral Retaining Ring For Current Production Spline Mount Replacement Hubs. More Info

$14.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56016 O-Ring for Warn® Current Production Spline Mount Replacement Hubs. More Info

$1.51
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56012 Original Equipment Warn® Hub Screw For Warn® Spline Mount Hubs in 1980-1982 Ford F-250, F-350 Dana 50IFS Front Axles. More Info

$2.18
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40113 Torx® Upgrade Screw For Warn® Spline Mount Hubs in 1980-1982 Ford F-250, F-350 Dana 50IFS Front Axles. More Info

$2.57
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56015 Replacement Decals For Warn® Plastic Hub Dials. More Info

$9.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts

top_page
photo

QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound. More Info

$6.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals and Pinion Yokes

top_page
product note

1980-1982 Ford Dana 50IFS Front Axles use a Pinion Yoke made for the oversize 1.125" u-joint cups used on the Ford specific 1330F universal joints (See TK40723 and QU40776 ).

photo

QU20180 Ford Dana 50IFS Front Axle Pinion Yoke Is a genuine original equipment Ford Front Pinion Yoke for 1980-1982 Ford F-250, F350 4x4s. This Pinion Yoke fits all Dana 50 IFS (IFS=Independent Front Suspension) Twin Traction Beam™ front drive axles. More Info

Also available while supplies last: QU20180U, QU40850B

$64.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40578 Pinion Seal for Ford Dana 50 Is a genuine Dana original equipment Pinion Seal for 1980-1982 Ford F250 and 1980-1982 F350 Dana 50 IFS front axles. More Info

$15.16
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40841 Driveshaft U-Bolt Kit for Ford Dana 50 Front Axle Fits all 1980-1982 Ford original equipment Front Dana 50IFS pinion yokes. More Info

$7.76
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
product note

Dana 50 Ring and Pinion Sets are similar in size to but NOT interchangeable with Dana 44 gear sets. The Dana 50IFS front axle was available in only two factory ratios: 3.54 and 4.10. Since Dana 50 monobeam axles from 1999-2005 Super Duty/Excursion 4x4s use the same diff, you also have two optional ratios available: 3.73 (QU20236U) and 4.30 (QU20237U) . We have a limited stock of good used Ring and Pinion Sets for your Dana 50 IFS front axle, plus we can still supply new gear sets for most ratios in 3-7 days.

photo

QU20274U Used 3.54 Ratio Dana 50 Ring and Pinion Set Is a good used factory 3.54 ratio gear set for 1980-1982 Ford F250 and 1980-1982 Ford F350 4x4 trucks with Dana 50 IFS front axles. More Info for Dana 50 Ring and Pinion Sets

$149.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20275U Used 4.10 Ratio Dana 50 Ring and Pinion Set Is a good used factory 4.10 ratio gear set for 1980-1982 Ford F250 and 1980-1982 Ford F350 4x4 trucks with Dana 50 IFS front axles. More Info for Dana 50 Ring and Pinion Sets

$124.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

YG D50R-354R High Performance Yukon Replacement Ring & Pinion Gear Set for 1980-1982 Ford 3/4 Ton F250 and 1 Ton F350 Dana 50IFS Reverse rotation in a 3.54 ratio. This fast gear set makes for good fuel economy. 9.00" Ring Gear Diameter, 26 Spline Pinion. Includes 10 ring gear bolts.

More Info

$286.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note

Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else.

photo

QU40009 Pinion Lock Nut More Info

$3.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40010 Pinion Washer More Info

$2.96
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40343 Differential Cap Bolt More Info

$2.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40028 Ford Dana 50 Inner Pinion Bearing Slinger Is a 4-/18" diameter, genuine Dana original equipment, flat steel Oil Slinger that was used on 1980-1982 Dana 50IFS front axles. More Info

$4.67
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40527 Dana 50 Inner Pinion Oil Baffle Is located under your inner pinion bearing cup on 1980-1982 Ford F-250 and 1980-1982 Ford F-350 4x4 trucks with Dana 50IFS Front Axles. More Info

$9.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40441 Dana 50 Ring Gear Bolt For 1980-1982 Ford F-250 and 1980-1982 Ford F-350 4x4 trucks with Dana 50IFS Front Axles. More Info

$1.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU50861 0 Degree Camber Bushing for Ford Dana model 50 IFS front axles. More Info

$29.47
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindles, Spindle Hardware, and Spindle Nuts

top_page
photo

QU40036 6 Slot Spindle Nut Is a genuine original equipment replacement nut for either the inner or outer front spindle nut for early Ford Dana 50 IFS front axles. Order 2 Nuts per side. More Info

$19.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40037 Bend-Over Tab Lockwasher for 6 Slot Spindle Nuts Is a genuine original equipment replacement lockwasher that fits between the inner and outer front spindle nut on early Ford Dana 50 IFS front axles. More Info

$8.51
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40038 Inner Thrust Washer for 6 Slot Spindle Nuts is a genuine original equipment replacement Thrust Washer that goes between inner front spindle nut and outer wheel bearing on early Ford Dana 50 IFS front axles. More Info

$14.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4728 6 Slot Spindle Nut Kit For early Ford Dana 50IFS axles includes QU40038 Inner Thrust Washer, Two QU40036 6 Slot Spindle Nuts, and QU40037 Bend Over Tab Spindle Lock Washer. More Info

$59.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20227U 1980-1982 Ford Dana 50 IFS Front Spindle Is a functional used original equipment Front Axle Wheel Bearing Spindle for all 1980-1982 Ford F-250 and 1980-1982 F-350 4x4 trucks with the Dana 50 Independent Front Suspension (IFS) front drive axle. These are rough but useable for off road use only! Not for highway use! More Info

$149.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU95036 Heat-treated, All Metal, Spindle to the Steering Knuckle Lock Nut Six of these USA Made, 150,000 psi rated Locknuts fit on QU40540 Spindle to Knuckle Bolt to secure each of your front Spindles to the Steering Knuckles. More Info

$1.50
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40539 Spindle-to-Knuckle Bolt Five of these press-in special bolts fit each steering knuckle on 1980-1982 Ford F-250, F-350 Dana 50IFS Front Axles. They are used along with QU95036 Locknut to retain your spindles and caliper anchor plates. More Info

$4.48
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Bearings and Seals

top_page
product note

The dead, hollow spindle design of the 1980-1982 era Ford Dana 50 IFS axles use QU40149 needle bearing to support the outer axle shaft. Axial thrust is handled by a plastic thrust washer. Two V-Seals are used to protect the spindle bearing. We stock all the individual components, plus Kits combining the pieces.

photo

QU40064 1980-1982 Ford Dana 50 Outer Axle Shaft Slinger Is a genuine Dana Spicer part that press fits on the outer axle shafts of Dana Model 50IFS open knuckle front drive axles for your 1980-1982 Ford Dana 50IFS Front Axle. More Info

$6.89
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40065 Large Spindle V-Seal Is a genuine Dana Spicer part that fits between the spindle and QU40064 outer axle shaft slinger in Model 50IFS open knuckle front drive axles on your 1980-1982 Ford Dana 50IFS Front Axle. More Info

$11.05
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40066 1980-1982 Ford Dana 50 Outer Axle Shaft to Spindle Thrust Washer Is a genuine Dana Spicer part that fits on your Dana 50 outer axle shaft to control thrust between the axle shaft and spindle. More Info

$6.01
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40148 1980-1982 Ford Dana 50 Small Spindle V-Seal Is a genuine Dana Spicer part that fits in the back of your spindle between QU40149 spindle bearing and QU40066 thrust washer in 1980-1982 Ford Dana 50IFS Front Axles. More Info

$7.77
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40149 1980-1982 Ford Dana 50 Spindle Bearing Is a genuine Dana Spicer original equipment part that is a press fit in the back of the spindle. This bearing is the primary support for your outer axle shaft. More Info

$19.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4740 1980-1982 Ford Dana 50 6 Piece Large Spindle Seal and Thrust Washer Kit Services BOTH sides of your 4x4 with two each of these parts: QU40065 Large Spindle V-seal, QU40066 Spindle Thrust Washer, and QU40148 Small Spindle V-seal. More Info

$42.82
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40168 1980-1982 Ford Dana 50 Spindle Bearing and Seal Kit Services ONE side of your 4x4 with one each of these parts: QU40065 Large Spindle V-seal, QU40066 Spindle Thrust Washer, QU40148 Small Spindle V-seal, and QU40149 Spindle Bearing. More Info

$32.98
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
photo

QT5500 Wheel Bearing Packer Takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your big Ford! More Info

$33.53
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers. More Info

$19.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1801 Outer Wheel Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50411 Outer Wheel Bearing Cup a simple and fast procedure. More Info

$23.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1804 Inner Wheel Bearing Cup Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50396 Inner Wheel Bearing Cup a simple and fast procedure. More Info

$26.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1505 Front Wheel Seal Installer Is custom made to quickly and easily install your new wheel seals without damaging them. More Info

$32.95
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals (Individual)

top_page
product note

Ford used only the best wheel bearings and seals money could buy to equip their Dana 50 IFS front axles to minimize the chance for warranty problems. That is why they chose Timken® Wheel Bearings and Spicer Wheel Seals for heavy-duty Ford 3/4 ton and 1 Ton 4x4s using the Dana 50 IFS axles. We supply those exact original equipment replacement Timken® Wheel Bearings and Spicer Wheel Seals to keep your Ford on the job for years to come.

photo

QU50411 Timken® Outer Wheel Bearing Cup More Info

$8.15
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50412 Timken® Outer Wheel Bearing More Info

$14.46
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50396 Timken® Inner Wheel Bearing Cup More Info

$10.91
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50398 Timken® Inner Wheel Bearing More Info

$19.28
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40119 Inner Wheel Seal Is a genuine Dana-Spicer original equipment replacement seal for your Ford heavy duty 3/4 ton & 1 ton 4x4 trucks with open knuckle Dana 50IFS. More Info

$9.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
photo

TK4744 Torque King® 1980-1982 Front Wheel Bearing and Seal Kit without Tools Is a parts only (No Tools) Complete Front Wheel Bearing and Seal Kit for your Ford heavy duty 3/4 ton & 1 ton 4x4 trucks with open knuckle Dana 50IFS featuring Timken® Bearings and original equipment wheel seals. More Info

$122.70
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4738 Torque King® 1980-1982 Front Wheel Bearing and Seal Kit with Install Tools For all 1980-1982 Ford heavy duty 3/4 ton & 1 ton 4x4 trucks with open knuckle Dana 50IFS front drive axles. Kit includes Inner Wheel Bearing Cup Installer, Outer Wheel Bearing Cup Installer, Wheel Seal Installer, Driver Handle, plus 2 each of Timken® Inner and Outer Wheel Bearings/Bearing Cups, plus two Wheel Seals. This Kit DOES NOT INCLUDE Spindle Nut Socket or Hub Small Parts for your Ford!!! More Info

$219.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4893 Torque King® 1980-1982 Front Timken Wheel Bearing Only Kit For your Ford heavy duty 3/4 ton & 1 ton 4x4 trucks with open knuckle Dana 50IFS featuring Timken® Bearings. More Info

$105.00
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Discontinued Parts

top_page
photo

QU40470 Axle Shaft Universal Joint for 1980-1983 Ford Dana 50 Front Axles Is an original equipment replacement, factory lubed, non-greaseable, external snap ring u-joint 1980 to 1983 Ford Dana 50 Twin Traction Beam® IFS front axles which were available on F-250 trucks and F-350s. Discontinued.

photo

QU40173 Right Axle Shaft Bearing and Seal Kit Is a genuine original equipment Dana Kit for 1980-1982 Ford Dana 50 IFS Front Axles with bolt in right side differential output shafts. Superseded by QK4035.