Parts for Dana-Spicer Model 50 IFS Front Axles in 1983-1997 Ford F-250, F-350 4x4 Trucks

We stock a good selection of replacement parts for 1983.5 to 1997 Ford F-250 and 1983.5-1985.5 Ford F350 4x4 trucks with Dana Spicer Model 50 Independent Front Suspension (IFS) Twin Traction Beam® drive axles. First used in 1980, the Ford IFS Twin Traction Beam® Dana 50 axle went through a significant differential and right side inner axle shaft design changes for vehicles built in 1983 starting with Dana Axle Bill of Material number 610170 (Ford Axle Codes E2TA-DA, E2TA-HA, E3TA-HFA). The exact date of change is not listed in Fords parts books, however 1983 is the only model year that vehicles with either axle design were manufactured.

Axle Identification

top_page
product note
Ford was the only vehicle manufacturer to use Dana Twin Traction Beam® Independent Front Suspension Axles which can be found on 1980-1997 model year Ford 4x4s. The Twin Traction Beam® IFS Axle line includes the coil spring Models 28 and 35 found in Bronco II, Explorers and Ranger pickups, the Model 44 which was used in fill size Broncos, F-150 (coil springs), and light duty F-250 pickups (leaf springs), and the leaf sprung 4500 to 4600 pound rated Model 50IFS axle in heavy GVW F-250 and 1980-1985.5 F-350 trucks
photo
Hub Size: Ford used both Dana 44 and Dana 50 IFS Twin Traction Beam® Front Axles in F-250 trucks. The easiest way to tell them apart is by measuring the diameter of the wheel hub or locking hub. Dana 44 axles have hubs that are approximately 3-3/8" in diameter. Dana 50 Hubs are about 4-1/8" in diameter
Right Differential Output Shaft: The major difference between 1980-1983.5 and 1983.5-1997 Ford Dana 50IFS front axles is the way the right differential output shaft is supported and retained. The early axles use a pressed-on taper roller bearing and an external bolt-on retaining flange. Later production axles use a straight roller bearing pressed into the differential housing and the axle shaft is retained by a snap ring inside the differential next to the differential side gear. The early right diff output shafts could be pulled without removing the differential housing from the axle beam with a special slide hammer puller attachment, but seal replacement also requires the bearing be replaced. For later axles, you MUST remove the differential housing from the axle beam to access the snap ring, but once it is out replacing the right seal is quick and easy
Suspension: Leaf spring
Knuckle Mounting: Ball Joints
Wheel Hub: 1983-1997 Ford Model 50 axles have an internally splined hub in which a splined lockout hub assembly would fits into

Axle Assemblies and Axle Housings

top_page
product note
Dana 50IFS front axle beams and diff housings were pretty much unchanged from 1983 to 1997. 1982 and earlier diff housings were configured for a bolt-in right differential output shaft. 1983 and later housing have differential output shafts that are held in place by a snap ring next to the differential side gear. The axle beams were the same for 1983-1997 axles, but different replaceable upper ball joint camber bushings were used depending upon the year and suspension. I recommend you replace the Axle Beam Pivot Bushing before installing one of these Used Axle Beams
photo
QU20280U Left Ford Dana 50IFS Axle Beam Is a good used drivers side bare Axle Beam for 1980-1997 F250 and 1980-1985 F350 4x4s with Dana 50IFS front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20281U Right Ford Dana 50IFS Axle Beam Is a good used passenger side bare Axle Beam for 1980-1997 F250 and 1980-1985 F350 4x4s with Dana 50IFS front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50097 Axle Beam Pivot Bushing Fits either left or right axle beams. One of these Bushings gets pressed into the inboard end of each axle beam
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20279U Ford Dana 50 IFS Front Differential Housing With Bearing Caps is a good used Differential Housing for 1983-1997 Ford F250 and 1983-1985.5 F350 4x4 trucks With Dana 50IFS Front Axle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20246U-2 Differential Bearing Caps for Ford Dana 50 Axles Differential Bearing Caps are line bored for each axle and considered non-interchangeable. However, if you do not have a differential case spreader with Dana 50 IFS adapters, you can use an extra pair of caps to seat the differential, then remove them and replace with the original caps
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shafts

top_page
product note

We still have brand new left and right Axle Shafts in stock for 1983-1997 Ford 4x4s with Dana 50 IFS Front Axle. Production on these shafts ended years ago, so when our current limited inventory is exhausted that will be the end of new assemblies. Our available used axle shaft inventory is also limited due to the Cash for Clunkers program and high scrap prices which has sent large numbers of 1983-1997 Fords with Dana 50 axles straight to the crusher.

photo
QK4773/QK4773R Left Axle Shaft Assembly with Torque King U-Joint For all 1983 to 1997 Ford F-250 and 1983-1985 Ford F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle. QK4774 is an all new left axle shaft assembly. QK4774R is a reconditioned assembly that includes good used axle shafts and a new TK40719Torque King® Cold Forged U-joint.
Link to our large text QK4773 catalog page.
photo
QK4774/QK4774R Right Axle Shaft Assembly with Torque King U-Joint For all 1983 to 1997 Ford F-250 and 1983-1985 Ford F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle. QK4774 is an all new right axle shaft assembly. QK4774R is a reconditioned assembly that includes good used axle shafts and a new TK40719Torque King® Cold Forged U-joint.
Link to our large text QK4774 catalog page.
photo
QU40435 New Right Axle Inner Shaft For all 1983 to 1997 Ford F-250 and 1983-1985 Ford F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle.
Link to our large text QU40435 catalog page.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40824 New Left Axle Inner Shaft For all 1983 to 1997 Ford F-250 and 1983-1985 Ford F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle.
Link to our large text QU40824 catalog page.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40824U Used Left Axle Inner Shaft For all 1983 to 1997 Ford F-250 and 1983-1985 Ford F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle
photo
QU40571U Used Dana 50IFS Right Differential Output Shaft For all 1983 to 1997 FordF-250 and 1983-1985 Ford F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle.

Link to our large text QU40571 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40815 Dana 50IFS Right Axle Shaft Slip Yoke For all 1983 to 1997 Ford F-250 and 1983-1985 Ford F-350 4x4 trucks equipped with the Dana 50 IFS Twin Traction Beam® Front Axle.

Link to our large text QU40815 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20079 Ford Outer Axle Shaft Is a brand new, genuine Dana original equipment axle shaft for all 1983-1997 Ford F250 and 1983-1985.5 F350 4x4 trucks with Dana 50IFS front axles.

Link to our large text QU20079 catalog page.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20374U Used Ford Outer Axle Shaft Is a good used, genuine Dana original equipment axle shaft for 1983-1992 Ford F250/F350 4x4 trucks with Dana 50IFS front axles. These low cost Axles have 1 snap ring groove at the outboard end so they are not suitable for later model trucks with hub locks that use an inboard snap ring.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Boots and Seals For Inner Axle Shafts

top_page
product note
Ford introduced a redesigned Dana 50IFS Twin Traction Beam Front Axle during the 1983 model year that uses a right Differential Output Shaft retained by a C-Clip inside the axle housing. The new design requires the Differential Housing be removed from the left axle beam to service the Right Axle Shaft Seal and/or center axle universal joint. Also introduced was a right Axle Slip Joint protected by a flexible rubber Boot instead of a pressed on Yoke Seal. The Slip Yoke Boot eliminated one of the chronic problems the previous 1980-early 1983 axle had, namely axle shaft spline failure from water and grit infiltrating past the seal
photo
QU40087 Left Ford Dana 50 IFS Axle Shaft Seal Fits all 1983-1997 Ford F-250 and 1983-1985.5 F-350 4x4 trucks with Dana 50 Twin Traction Beam® IFS front axles.

Link to our large text QU40087 catalog page.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40088 Right Ford Dana IFS Axle Shaft Seal Fits all 1983-1997 Ford F-250 and 1983-1985.5 F-350 4x4 trucks with Dana 50 Twin Traction Beam® IFS front axles that have the right inner axle shaft retained by a snap ring.

Link to our large text QU40088 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40534 Right Side Differential Output Bearing and Seal Kit for Ford Dana 50 IFS Front Axles Is a genuine original equipment Kit that includes the right Axle Shaft Support Bearing, Right Axle Shaft Oil Seal and Axle Shaft Retaining Clip. Fits 1984-1996 Ford Dana 50 Twin Traction Beam IFS front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40515 Right Differential Output Shaft Support Bearing For 1984-1996 Ford Dana 50 IFS Front Axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40226 Retaining Ring for Ford Dana 44, Dana 50 IFS Differential Output Shafts Is a genuine original equipment spring steel Snap Ring that fits in a groove on your innermost right axle shaft on 1984-1996 Ford Dana 44IFS and 1983.5-1997 Ford Dana 50 IFS Twin Traction Beam® front axles in full size Ford 4x4s
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40557 Axle Shaft Slip Yoke Seal for Ford Dana 50IFS Twin Traction Beam® Front Axles Is a genuine original equipment part for all 1983.5-1997 Ford Dana 50 IFS Twin Traction Beam® front axles in 1983.5-1997 F-250 and 1983.5-1985.5 F-350 Ford 4x4s.

Link to our large text QU40557 catalog page.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40572 Ford Dana 50IFS Right Axle Shaft Slip Yoke Boot Is a genuine original equipment replacement Boot for all 1983-1997 Ford F-250 and 1983-1985.5 F-350 4x4 Trucks with Dana 50 Twin Traction Beam® IFS front axles that have the right inner axle shaft retained by a snap ring.

Link to our large text QU40572 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40085 One Ear Stainless Steel Boot Clamp For the small end of QU40572 Slip Yoke Boot.

Link to our large text QU40085 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40084 One Ear Stainless Steel Boot Clamp For the large end of QU40572 Slip Yoke Boot.

Link to our large text QU40084 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Boots and Seals For Outer Axle Shafts

top_page
product note
Ford introduced a redesigned Dana 50IFS Twin Traction Beam Front Axle during the 1983 model year that uses a right Differential Output Shaft retained by a C-Clip inside the axle housing. The new design requires the Differential Housing be removed from the left axle beam to service the Right Axle Shaft Seal and/or center axle universal joint. Also introduced was a right Axle Slip Joint protected by a flexible rubber Boot instead of a pressed on Yoke Seal. The Slip Yoke Boot eliminated one of the chronic problems the previous 1980-early 1983 axle had, namely axle shaft spline failure from water and grit infiltrating past the seal
photo
QU40087 Left Ford Dana 50 IFS Differential to Axle Shaft Seal is a genuine Dana Left Axle Seal that fits all 1983-1997 Ford F-250 and 1980-1985.5F-350 4x4 trucks with Dana 50 Twin Traction Beam® IFS front axles

Link to our large text QU40087 catalog page.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40088 Right Ford Dana 50 IFS Differential to Axle Shaft Seal Fits all 1983-1996 Ford F250 and 1983-1985.5 F350 4x4 trucks with Dana 50 Twin Traction Beam® IFS front axles that have the right inner axle shaft retained by a snap ring.

Link to our large text QU40088 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40243 Outer Axle Shaft to Spindle Seal for 1993-1997 Ford F-250 Is a genuine original equipment Seal that presses on your Ford 1993-1997 F-250, outer axle shaft next to the yoke. The lip of the seal rides against your spindle.

Link to our large text QU40243 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40496 Ford Dana 50 IFS Unitized Inner Spindle Seal and Thrust washer Is a genuine original equipment unitized spindle seal and thrust washer used on 1993-1997 Ford F-250 4x4s with the Dana 50 IFS Twin Traction Beam front axle.

Link to our large text QU40243 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40372 Ford Dana 50 IFS Unitized Spindle Seal, Bearing and Thrust Washer Kit Is a genuine original equipment Spindle Bearing, Spindle Seal and Spindle Thrust Washer set for 1993-1997 Ford F-250 4x4s with the Dana 50 IFS Twin Traction Beam front axle. Order 2 QU40372 per vehicle.

Link to our large text QU40372 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40149 1993-1997 Ford Dana 50 Spindle Bearing Is a genuine Dana Spicer original equipment part that is a press fit in the back of the spindle. This bearing is the primary support for your outer axle shaft.

Link to our large text QU40149 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note
The Dana 50 IFS axle has 3 axle universal joints, one for the left side and two for the right side. For the 460 gas engine and later diesel trucks, this size u-joint is a bit on the small size. For the Dana 50, we offer QK4874 Greaseable U-joint as an inexpensive alternative to our TK40719 cold-forged, solid cross, non-greaseable u-joint which is our as our maximum strength option for these axles. QK4874 Greaseable U-joint is a whole lot cheaper compared to TK40719, but there is some strength loss since it is cross-drilled for grease passage
photo
QK4874 Greaseable External Snap Ring Axle Universal Joint for 1983-1997 Ford Dana 50 Front Axles In 4x4 F-250 and F-350 trucks with Dana 50 IFS Twin Traction Beam® IFS front axles.

Link to our large text QK4874 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40470 Axle Shaft Universal Joint for 1983-1997 Ford Dana 50 Front Axles Is an original equipment replacement, factory lubed, non-greaseable, external snap ring u-joint 1980 to 1997 Ford Dana 50 Twin Traction Beam® IFS front axles which were available on F-250 trucks for all years, plus 1980 to early 1985 F-350s. Use QK4874 above or TK40719 below
photo
TK40719 Torque King® Premium Quality, Non-Greaseable Axle U-Joint has a cold-forged, alloy steel cross, synthetic-lubricant, superior seals and External Snap Rings. This U-Joint with it's cold-forged, solid cross is the strongest u-joint we offer for your Ford Dana 50 front axles shafts. To install this u-joint, the inside ears of your yokes will need to be slightly modified with a file.

Link to our large text QU40719 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ball Joints

top_page
product note

Ford Dana 50IFS Front Axles use a unique lower Ball Joint that was not used on any other application. The original, non-greaseable Ball Joints are no longer available through Dana, but we do a have premium greaseable, Dana made replacement Ball Joints available for your big Ford either individually or in a complete set of 4 Ball Joints. To press your Ball Joints in or out of the steering knuckles, see TS4511 Ball Joint Press Set which also works on many Dana 60 axles

photo
QK4561 Greaseable Ball Joint Kit for Ford Dana 50 IFS Front Axles Includes 2 upper and 2 lower Premium Quality Greaseable Ball Joints with hardware for all 1983-1997 Ford F-250 and 1983-1985.5 F-350 4x4 trucks with Dana 50 4600 lb. front axles
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50095 Premium Greaseable Upper Ball Joint With hardware for 1983-1997 Ford Dana 50 IFS Front Axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50056 Premium Greaseable Lower Ball Joint With hardware for 1983-1997 Ford Dana 50 IFS Front Axles

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
product note
Our stock of Ford Dana 50 front brake parts is limited. For the most part, the front brakes generally gave pretty good service that was comparable to the contemporary Dodge and GM 4x4's with one exception. We saw a lot higher percentage of Fords with warped or cracked brake rotors compared to the competition. Whether this was due to the somewhat thinner Ford brake rotor thickness or our Ford customers were harder on their brakes, I can't say, but a F-250 or F-350 that was used to frequently tow a trailer always seemed to need rotors
photo
QU20054 Front Disc Brake Caliper Tension Spring For 1983-1985 Ford F250, F350 Dana 50IFS front axle with dual piston calipers secured a bottom mounted U-shaped single caliper slide and a separate tension spring
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU80002 Caliper Slide Lock Bolt Is a special, hex head bolt that threads into the caliper anchor plate on your disc brake equipped 1983-1985 Ford F250, F350 Dana 50IFS front axle with dual piston calipers secured a bottom mounted U-shaped single caliper slide and a separate tension spring. The tapered body between the threads and end fits into the inner notch of the caliper slide or key. QU80002 is plated for corrosion resistance
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20065 Disc Brake Caliper Pin For Bronco, F150, F250, F350 mid 1980's to mid 1990's. Genuine OEM Ford part. Link to our large text individual QU20065 detail page
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20284 1983-1994 Left Front Brake Splash Shield Is a genuine original equipment part for 1983-1994 Ford F250 and 1983-1985.5 F350 with Dana 50 IFS 4600 pound front axles. Link to our large text individual QU20284 detail page with tech notes.
Also available while supplies last: QU20284U Good Used 1980-1994 Left Front Brake Splash Shield
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20285 1983-1994 Right Front Brake Splash Shield Is a genuine original equipment part for 1983-1994 Ford F250 and 1983-1985.5 F350 with Dana 50 IFS 4600 pound front axles. Link to our large text individual QU20285 detail page with tech notes.
Also available while supplies last: QU20285U Good Used 1980-1994 Right Front Brake Splash Shield
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20286 1995-1997 Left Front Brake Splash Shield Is a genuine original equipment part for 1995-1997 Ford F250 with Dana 50 IFS 4600 pound front axles. Link to our large text QU20286 catalog page with detail & tech notes
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20287 1995-1997 Right Front Brake Splash Shield Is a genuine original equipment part for 1995-1997 Ford F250 with Dana 50 IFS 4600 pound front axles. Link to our large text QU20287 catalog page with detail & tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings (Individual)

top_page
product note
If you only need a bearing or two for your 1983-1997 Ford Dana 50IFS diff, we stock the best: Timken®. For the amount of work it takes to change most axle bearings, the extra cost for a Timken® diff or pinion bearing is a small price to pay for better steel, more uniform surface finish, and accurate, precision ground races
photo
QU50533 Ford Dana 50 Timken® Outer Pinion Bearing Cup

Link to our large text QU50533 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50534 Ford Dana 50 Timken® Outer Pinion Bearing

Link to our large text QU50534 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50539 Ford Dana 50 Timken® Inner Pinion Bearing Cup

Link to our large text QU50539 catalog page.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50540 Ford Dana 50 Timken® Inner Pinion Bearing

Link to our large text QU50540 catalog page.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50541 Ford Dana 50 Timken® Differential Side Bearing Cup

Link to our large text QU50541 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50542 Ford Dana 50 Timken® Differential Side Bearing

Link to our large text QU50542 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing and Seal Kits

top_page
product note
All 1980-2005 Ford Dana 50 front axles have the same differential and pinion bearings. The pinion seals and method to set pinion preload vary by year. We offer two Kits with Timken Bearings. TK4885 includes JUST the diff and pinion bearings/cups, you can then individually order the exact extra original equipment parts you need for your specific axle. QU50581 is a "universal" Kit for all Dana 50 axles that has the same premium Timken bearings as TK4885 plus aftermarket small parts and 2 pinion seals.
photo
TK4885 Torque King® Dana 50 Differential and Pinion Bearing Only Kit For all Ford Dana 50 Twin Traction Beam IFS Front Axles in F250/F350 4x4 trucks. Kit includes Timken® Pinion and Differential Bearings with Bearing Cups. TK4885 includes just the bearings, order your seals, shims, and other small parts as needed from our complete selection of genuine Dana original equipment replacement components.

Link to our large text TK4885 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50581 Differential Bearing and Seal Kit For all Ford Dana 50 Twin Traction Beam IFS Front Axles in F250/F350 4x4 trucks. Kit includes Timken® Pinion and Differential Bearings with Cups, plus aftermarket replacement pinion seals, pinion nut, pinion preload shims, and crush sleeve. Also includes RTV sealant, thread locker, gear marking compound and brush.

Link to our large text QU50581 catalog page.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
product note

The Dana 50 axle is unusual in that no other vehicle manufacturer besides Ford ever used it for any application. This means Ford has a lock on the distribution and pricing of most new Dana 50 specific internal parts. Due to the advancing age of Dana 50 equipped vehicles, many Dana 50 differential parts are no longer available from Ford. However, we do have some new small parts and good used major parts for the Ford Dana 50 axle

photo
QU40519 Differential Cross Shaft Lock Pin Is a genuine Dana original equipment Roll Pin used to secure your differential cross shaft to the diff case on 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50 IFS Front Axles.

Link to our large text QU40519 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40576 Dana 50IFS Pinion and Differential Shim Kit For 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50 IFS Front Axles includes these genuine Dana parts: Pinion Depth Shims, Pinion Preload Shims, Differential Adjusting Shims, Axle Shaft Snap Ring, Pinion Nut and Pinion Washer.

Link to our large text QU40576 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20239 OEM Ford Dana 50 Internal Differential Parts Kit Fits 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50 IFS Front Axles. These are brand new, genuine original equipment internal diff gear sets for 3.73, 4.10, and 4.30 ratio Ford Dana 50IFS front axles.

Link to our large text QU20239 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20240U Loaded Differential Case Good Used Ford Dana 50 Differential Case Assembly for 1980-1997 Ford Dana 50 IFS (F250, F350) and 1999-2005 Ford Dana 50 Monobeam Front Axles (F250, F350 Single Rear Wheel, Excursion). These are good used loaded Diff Cases with internal gears for 3.54, 3.73, 4.10, and 4.30 ratio Ford Dana 50 front axles.

Link to our large text QU20240 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20401 Differential Cross Shaft for 1980-2005 Ford F250, F350, or Excursion with Dana 50IFS or Dana 50 Beam axles.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Makers

top_page
product note
A cut gasket is not used between the differential housing and left axle beam on Dana 50 IFS axles because it's thickness would cause the inner axle shafts to be slightly misaligned with the center of the spindles. High quality RTV sealant is used. The mating faces of the diff housing and axle beam MUST BE Clean! That means NO dirt, fingerprints, old sealant, oil etc. on either mating surface.
photo
S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential housing to the left axle beam on your Ford Dana 50 IFS Front Axle.

Link to our large text S82194 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hubs and Hub Parts

top_page
product note

We have limited stock on new original equipment Dana 50IFS Hub and Rotors. Ford used both manual and automatic hub locks for Dana 50IFS front axles. For Manual Hubs, we only stock parts for the 6 Bolt, Red or Black Dial (1983-1992) Warn built, factory plastic dial manual hubs. In 1993, Ford switched to a new manual hub style with a smaller grip, black plastic dial, which was superseded by a 3 bolt black plastic dial hub in 1995. We do not stock service parts for the 1993-1997 Ford factory black plastic dial manual hubs. Two versions of automatic hubs were used. We have no replacement parts for the 5 screw 1993-1994 auto hub, but we do have some small parts for the 1995-1997 auto hub with three screws

photo
QU20085 30 Spline Three Piece Axle Thrust Washer Set Fits on the outer axle shaft splines between the spindle and axle shaft snap ring on many 1993-1997 axles. Order 2 per vehicle.

Link to our large text QU20085 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TKA20332/QU20332U New and Used Front Hub for 1988-1994 F250 For 1988-1994 Ford F-250 4x4 trucks with Dana 50 IFS 4600 pound front axles

More Info

photo

TKA4923 Brand New Hub with Bearing Cups for 1995-1997 F250 Is a brand new splined Front Hub with Timken bearing cups for 1995-1997 Ford F-250 4x4 trucks with Dana 50 IFS 4600 pound front axles

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20264U Used 1995-1997 F250 8 Bolt 4x4 Front Wheel Hub Is a good used Ford splined Front Hub for 1995-1997 Ford F-250 4x4 trucks with Dana 50 IFS 4600 pound front axles.

Link to our large text QU20264 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU42116 30 Spline Drive Gear Kit for 1983-1997 Ford Dana 50IFS Front Axles with internal splined wheel hubs.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20357 1/2" Front Wheel Stud for 1980-1988 Dana 50 Is a hardened, 1/2" fine thread replacement wheel stud for those 1980-1988 Ford Ford Dana 50 IFS front axles with 1/2" Wheel Studs

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20355 9/16" Front Wheel Stud for 1980-1997 Ford Is a hardened, 9/16" fine thread replacement wheel stud for those 1980-1988 Ford Ford Dana 50IFS front axles with 9/16" Wheel Studs, plus all 1988.5-1997 F250 Dana 50 IFS front axles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20087 Hub Service Kit For Ford Dana 50 IFS Front Axles. QU20087 includes one QU20200 Spindle Nut, one Hub Spindle Nut Retaining Clip, (3) Hub Cap Screws, one Hub Decal, one Body Retaining Snap Ring, one Axle Shaft Snap Ring, one Sealing O-Ring, and one QU20085 3 piece Splined Axle Thrust Washer Set. Order 1 QU20087 per side. Link to our QU20087 large text catalog page for more detail and tech notes

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20200 Special Rounded Spindle Hex Nut Is a genuine original equipment replacement Spindle Nut for factory automatic hub equipped 1995 to 1997 Ford F-250 with Dana 50 front axles. Sold individually. Order two Nuts per vehicle. Link to our QU20200 large text catalog page for more detail and tech notes

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20201 Auto Hub Spindle Nut Retaining Clip For Ford Dana 50 IFS Front Axles

Link to our large text QU20201 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20202 Screw, Auto Hub Cap For Ford Dana 50 IFS Front Axles.

Link to our large text QU20202 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20203 Auto Hub Decal For Ford Dana 50 IFS Front Axles.

Link to our large text QU20203 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20207 Body Retaining Snap Ring For Auto Hub on Ford Dana 50 IFS Front Axles.

Link to our large text QU20207 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20208 Axle Shaft Snap Ring for Auto Hub On Ford Dana 50 IFS Front Axles.

Link to our large text QU20208 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20209 Sealing O-Ring for Auto Hub Cap On Ford Dana 50 IFS Front Axles.

Link to our large text QU20209 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56025 Warn 38826 Premium Hub Set for Dana 50IFS Front Axles With internally splined front wheel hubs. A sharp looking and reliable hub. QU56025 Fits Ford Dana 50IFS 1983-1997

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56011 Spline Mount Lockout Hub Set for 1983-1997 Ford F-250 Dana-Spicer Model 50IFS front drive axles and internally splined wheel hubs. QU56011 is the current production version of the Warn's original equipment 1980-1994 Ford Hub-Lock
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56022U Used Manual Lockout Hubs For 1995-1997 Ford F250 Dana 50IFS 4x4 front axles. These good used Manual Lockout Hubs have a 3 bolt cap. Sold as a pair. While supply lasts. Also available QU56022.5U Used Manual Lockout Hub for 1 side only, while supply lasts.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4916 Hub Service Kit For QU56011 Lockout Hubs includes 2 QU56017 Spiral Retaining Rings, 2 QU56016 O-Rings, 2 QU40068 Axle Shaft Snap Rings, 12 QU56012 Hub Screws, and 1 Set Replacement Decals.

Link to our large text QK4916 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40068 Axle Shaft Snap Ring Fits in the groove machined at the end of the outer axle shaft splines in Ford Dana 50 IFS Front Axles.

Link to our large text QU40068 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40150 Lockout Hub to Wheel Hub Snap Ring For Warn® Spline Mount Hubs used in Ford Dana 50 IFS Front Axles.

Link to our large text QU40150 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50116 Cap QUAD-Ring square cross section sealing ring For Factory Warn® Spline Mount Hubs in Ford Dana 50 IFS Front Axles.

Link to our large text QU50116 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50240 Dial O-Ring For Warn® Spline Mount Hub Dials in Ford Dana 50 IFS Front Axles.

Link to our large text QU50240 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56013 Warn® Dial Assembly For Original Equipment Spline Mount Hubs used in Ford Dana 50 IFS Front Axles.

Link to our large text QU56013 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56017 Warn® Spiral Retaining Ring For Current Production Spline Mount Replacement Hubs.

Link to our large text QU56017 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56016 Cap O-Ring For 1993.5-1997 factory manual hubs and Warn® Current Production Spline Mount Replacement Hubs.

Link to our large text QU56016 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56012 Original Equipment Warn® Hub Screw For Warn® Spline Mount Hubs in Ford Dana 50 IFS Front Axles.

Link to our large text QU56012 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40113 Torx® Upgrade Screw For Warn® Spline Mount Hubs in Ford Dana 50 IFS Front Axles.

Link to our large text QU40113 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts

top_page
product note
Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings
photo
S24200 Blue Threadlocker For spindle and ring gear bolts etc
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern.

Link to our large text QU90008 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90018 Pyroplex ® Protection ES Synthetic Grease Provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90016 SynPower ® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90015 Syncon High Performance Synthetic Arctic Grease Is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90017 707L Red Grease Is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. cartridge or 1 pound tub
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound.

Link to our large text QU90009 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals and Pinion Yokes

top_page
product note
1983-1997 Ford Dana 50IFS Front Axles use a Pinion Yoke made for the oversize 1.125" u-joint cups used on the Ford specific 1330F universal joints (See TK40723 and QU40776 ).
photo
QU20180 Ford Dana 50IFS Front Axle Pinion Yoke Is a genuine original equipment Ford Front Pinion Yoke for 1983-1997 Ford F-250 4x4s. This Pinion Yoke fits all Dana 50 IFS (IFS=Independent Front Suspension) Twin Traction Beam™ front drive axles.

Link to our large text QU20180 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40578 Pinion Seal for Ford Dana 50 Is a genuine Dana original equipment Pinion Seal for 1983-1997 Ford F250 and 1983-1985 F350 Dana 50 IFS front axles.

Link to our large text QU40578 catalog page.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40841 Driveshaft U-Bolt Kit for Ford Dana 50 Front Axle Fits all 1983-1997 Ford original equipment Front Dana 50 IFS pinion yokes.

Link to our large text QU40841 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
product note

Dana 50 Ring and Pinion Sets are similar in size to but NOT interchangeable with Dana 44 gear sets. The Dana 50IFS front axle was available in only two factory ratios: 3.54 and 4.10. Since Dana 50 monobeam axles from 1999-2005 Super Duty/Excursion 4x4s use the same diff, you also have two optional ratios available: 3.73 (QU20236U) and 4.30 (QU20237U) . We have a limited stock of good used Ring and Pinion Sets for your Dana 50 IFS front axle, plus we can still supply new gear sets for most ratios in 3-7 days.

photo
QU20274U Used 3.54 Ratio Dana 50 Ring and Pinion Set Is a good used factory 3.54 ratio gear set for 1983-1997 Ford F250 and 1983-1985 Ford F350 4x4 trucks with Dana 50 IFS front axles.

Link to our Large Text Dana 50 Ring and Pinion Sets Web Page

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20275U Used 4.10 Ratio Dana 50 Ring and Pinion Set Is a good used factory 4.10 ratio gear set for 1983-1997 Ford F250 and 1983-1985 Ford F350 4x4 trucks with Dana 50 IFS front axles.

Link to our Large Text Dana 50 Ring and Pinion Sets Web Page
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

YG D50R-354R High Performance Yukon Replacement Ring & Pinion Gear Set for 1983-1998 Ford 3/4 Ton F250 and 1 Ton F350 Dana 50IFS Reverse rotation in a 3.54 ratio. This fast gear set makes for good fuel economy. 9.00" Ring Gear Diameter, 26 Spline Pinion. Includes 10 ring gear bolts.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note
Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else
photo
QU40009 Dana 50 Pinion Lock Nut For securing your pinion yoke to the pinion shaft on 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50 IFS Front Axles.

Link to our large text QU40009 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40010 Dana 50 Pinion Washer Fits between the pinion nut and pinion yoke on 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50 IFS Front Axles.

Link to our large text QU40010 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40002 Dana 50 Outer Pinion Bearing Slinger Goes between your outer pinion bearing and pinion yoke on 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50 IFS Front Axles.

Link to our large text QU40002 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40028 Ford Dana 50 Inner Pinion Bearing Slinger Is a 4-/18" diameter, genuine Dana original equipment, flat steel Oil Slinger that was used on early to mid production Dana 50 IFS front axles.

Link to our large text QU40028 catalog page.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40527 Dana 50 Inner Pinion Oil Baffle Is located under your inner pinion bearing cup on 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50 IFS Front Axles.

Link to our large text QU40527 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40441 Dana 50 Ring Gear Bolt For 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50 IFS Front Axles.

Link to our large text QU40441 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40343 Dana 50 Differential Cap Bolt Is a genuine Dana Grade 8 Bolt. Two of these Bolts are used on each differential bearing cap on 1983.5-1997 Ford F-250 and 1980-1985 Ford F-350 4x4 trucks with Dana 50 IFS Front Axles.

Link to our large text QU40343 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40226 Retaining Ring for Ford Dana 50 IFS Differential Output Shafts Is a genuine original equipment spring steel Snap Ring that fits in a groove on your innermost right axle shaft on 1983.5-1997 F-250 and 1983.5-1985.5 F-350 Ford 4x4s.

Link to our large text QU40226 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40534 Right Side Differential Output Bearing and Seal Kit for Ford Dana 50 IFS Front Axles Is a genuine original equipment Kit that includes the right Axle Shaft Support Bearing, Right Axle Shaft Oil Seal and Axle Shaft Retaining Clip. Fits 1983.5-1997 F-250 and 1983.5-1985.5 F-350 Ford 4x4s.

Link to our large text QU40534 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindles and Spindle Nuts

top_page
product note

According to Dana-Spicer, they used only the 4 slot front spindle nut type for 1983-1997 F-350 Dana 60 Front Axles with manual hubs. However, the Ford factory parts lists shows the 6 Slot nut type as being used all the way to early 1985. The only way to know for sure what spindle nut your '83-'85 axle has is to remove the hub-lock and see what is in there! 1994-1997 Trucks with automatic hubs use a special rounded hex spindle nut

photo
QU20200 Spindle Nut for Auto Hubs On 1994-1997 Ford F-250 3/4 ton 4x4 trucks with the Dana 50 front drive axle. Uses with QU20201 Retaining Clip.

Link to our large text QU20200 catalog page.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20201 Auto Hub Spindle Nut Retaining Clip For Ford Dana 50 IFS Front Axles.

Link to our large text QU20201 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40036 6 Slot Spindle Nut Is a genuine original equipment replacement nut for either the inner or outer front spindle nut for early Ford Dana 50 IFS front axles. Order 2 Nuts per side.

Link to our large text QU40036 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40037 Bend-Over Tab Lockwasher for 6 Slot Spindle Nuts Is a genuine original equipment replacement lockwasher that fits between the inner and outer front spindle nut on early Ford Dana 50 IFS front axles.

Link to our large text QU40037 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40038 Inner Thrust Washer for 6 Slot Spindle Nut S is a genuine original equipment replacement Thrust Washer that goes between inner front spindle nut and outer wheel bearing on early Ford Dana 50 IFS front axles.

Link to our large text QU40038 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4728 6 Slot Spindle Nut Kit For early Ford Dana 50IFS axles includes QU40038 Inner Thrust Washer, Two QU40036 6 Slot Spindle Nuts, and QU40037 Bend Over Tab Spindle Lock Washer.

Link to our large text QK4728 catalog page.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40163 4 Slot Ford Dana50 IFS Round Outer Spindle Nut For 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4s with manual hubs has 4 slots for QT1018 Spindle Nut Wrench.

Link to our large text QU40163 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40164 Ford Dana 50 IFS Spindle Lock Washer For 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4s with 4 Slot round spindle nuts is reusable.

Link to our large text QU40164 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40166 4 Slot Ford Dana 50 IFS Round Inner Spindle Nut with Pin For 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4s has 4 slots for QT1018 Spindle Nut Wrench. Includes round pin that engages one of the holes in QU40164 Spindle Lock Washer.

Link to our large text QU40166 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4729 4 Slot Ford Dana 50 IFS Round Spindle Nut Kit For 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4s includes one each QU40163, QU40164, and QU40166 .

Link to our large text QK4729 catalog page.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK20227/QU20227U 1983-1997 Ford Dana 50 IFS Front Spindle Are new and used Front Axle Wheel Bearing Spindles for all 1983-1997 Ford F-250 and 1983-1985 F-350 4x4 trucks with the Dana 50 Independent Front Suspension (IFS) front drive axle.

Link to our large text TK20227 catalog page.

photo

QU95036 Heat-treated, All Metal, Spindle to the Steering Knuckle Lock Nut Six of these USA Made, 150, 000 psi rated Locknuts fit on QU40540 Spindle to Knuckle Bolt to secure each of your front Spindles to the Steering Knuckles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40539 Spindle-to-Knuckle Bolt Five of these press-in special bolts fit each steering knuckle on 1983-1997 Ford F-250 and 1983-1985 F-350 Dana 50 IFS Front Axles. They are used along with QU95036 Locknut to retain your spindles and caliper anchor plates.

Link to our large text QU40539 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Bearings and Seals

top_page
product note
The dead, hollow spindle design of the 1983-1992 era Ford Dana 50 IFS axles use QU40149 needle bearing to support the outer axle shaft. Axial thrust is handled by a plastic thrust washer. Two V-Seals are used to protect the spindle bearing. We stock all the individual components, plus Kits combining the pieces.
For 1993-1997 Model Years, Also see our Outer Axle Shaft Seal Section for Outer Axle Shaft Bearings, Thrust Washers, and Axle/Spindle Grease Seals
photo
QU40064 1983-1992 Ford Dana 50 Outer Axle Shaft Slinger Is a genuine Dana Spicer part that press fits on the outer axle shafts of Dana Model 50 IFS open knuckle front drive axles for your 1983-1992 Ford Dana 50IFS Front Axle.

Link to our large text QU40064 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40065 Large Spindle V-Seal Is a genuine Dana Spicer part that fits between the spindle and QU40064 outer axle shaft slinger in Dana Model 50 IFS open knuckle front drive axles on your 1983-1992 Ford Dana 50IFS Front Axle.

LIMITED SUPPLY!!

Link to our large text QU40065 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40066 1983-1992 Ford Dana 50 Outer Axle Shaft to Spindle Thrust Washer Is a genuine Dana Spicer part that fits on your Dana Model 50 IFS outer axle shaft to control thrust between the axle shaft and spindle.

Link to our large text QU40066 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40148 1983-1992 Ford Dana 50 Small Spindle V-Seal Is a genuine Dana Spicer part that fits in the back of your spindle between QU40149 spindle bearing and QU40066 thrust washer in 1983-1992 Ford Dana 50 IFS Front Axles.

Link to our large text QU40148 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40149 1983-1992 Ford Dana 50 Spindle Bearing Is a genuine Dana Spicer original equipment part that is a press fit in the back of the spindle. This bearing is the primary support for your outer axle shaft.

Link to our large text QU40149 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4740 1983-1992 Ford Dana 50 6 Piece Large Spindle Seal and Thrust Washer Kit Services BOTH sides of your 4x4 with two each of these parts: Large Spindle V-seal, QU40066 Spindle Thrust Washer, and QU40148 Small Spindle V-seal.

LIMITED SUPPLY!!

Link to our large text QK4740 catalog page.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40168 1983-1992 Ford Dana 50 Spindle Bearing and Seal Kit Services ONE side of your 4x4 with one each of these parts: QU40065 Large Spindle V-seal, QU40066 Spindle Thrust Washer, QU40148 Small Spindle V-seal, and QU40149 Spindle Bearing.

Link to our large text QU40168 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40372 1993-1997 Ford Dana 50 IFS Unitized Spindle Seal, Bearing and Thrust Washer Kit Is a genuine original equipment Spindle Bearing, Spindle Seal and Spindle Thrust Washer set for 1993-1997 Ford F-250 4x4s with the Dana 50 IFS Twin Traction Beam front axle. Order 2 QU40372 per vehicle.

Link to our large text QU40372 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Knuckles

top_page
product note
Ford used several different steering knuckle part numbers for the 1983-1997 era Dana 50IFS front axle. There are three major knuckle variations depending upon the type of brake caliper used. From 1983 to 1985 the calipers are held in place by a slide and spring placed between the lower edge of the caliper and the knuckle casting. 1986-1994 calipers are retained by upper and lower long, diamond shaped rubber and steel pins. Each end of the caliper has a V-shaped groove as does the caliper support arms that are part of the knuckle. 1995-1997 knuckles are made for bolt-on caliper anchor plates. There are also casting differences for the first two knuckle types depending upon the year.
Tech Note: After installing a replacement knuckle always have your front end aligned
QU20288U Used Left 1986-1994 Ford F250 Dana 50 Steering Knuckle Fits the drivers side axle beam on 1986 to 1994 Ford F250 4x4 trucks with Dana 50IFS front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU20289U Used Right 1986-1994 Ford F250 Dana 50 Steering Knuckle Fits the drivers side axle beam on 1986 to 1994 Ford F250 4x4 trucks with Dana 50IFS front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20335U Used Right 1995-1997 Ford F250 Dana 50 Right Steering Knuckle Fits the passenger side axle beam on 1995 to 1997 Ford F250 4x4 truck Dana 50IFS front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20336U Used Left 1995-1997 Ford F250 Dana 50 Steering Knuckle Fits the drivers side axle beam on 1995 to 1997 Ford F250 4x4 truck Dana 50IFS front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
photo
QT5500 Wheel Bearing Packer Takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your big Ford!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1815 Dana 50 Inner Pinion Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50539 Inner Pinion Bearing Cup a simple and fast procedure
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1812 Outer Pinion Bearing Cup Installer Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50533 Outer Pinion Bearing Cup a simple and fast procedure
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1025 6 Prong Spindle Nut Socket for 6 Slot Round Nuts Used on early Ford Dana 50IFS Front axles with QU40036 Spindle Nuts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1110 4 Prong Spindle Nut Socket for 4 Slot Round Nuts Used on later Dana 50IFS Front axles with QU40163 and QU40166 Spindle Nuts
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1058 Rounded Hex Spindle Nut Socket For 1994-1997 F250 4x4 trucks with factory automatic locking hubs
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1033 Case Spreader Is used to relieve the differential bearing preload making it easy to safely remove and install your front differential without damaging expensive critical parts. (Dana 50 axles also require you fabricate adapters with 2 pins.)
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1023 Triple Thread Universal Spindle Puller Use with any 5/8" fine thread slide hammer to quickly and easily remove those rusted in QU40169 or QU40420 front wheel bearing spindles on your 1983-1997 Ford Dana 50 front drive axle without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials. Also works on most GM 10 Bolt, Dana 50IFS, Dana 44, Dana 30, Dana 27, and Dana 25 front axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1024 Triple Thread Ford Spindle Puller Use with any 5/8" fine thread slide hammer to quickly and easily remove those rusted in QU40169 or QU40420 front wheel bearing spindles on your 1983-1997 Ford Dana 50 front drive axle without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials. Also works on most Dana 44, Dana 35 IFS, and Ford Dana 28IFS front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1200 Tie Rod Separator Allows you to remove the separate tie rod and drag link ends without wrecking the seals or screwing up your steering linkage ends
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT9018 5 Pound Dead Blow Hammer Is just about the first tool you will reach for to complete a multitude of jobs on your Dodge Ram. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1801 Outer Wheel Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50411 Outer Wheel Bearing Cup a simple and fast procedure
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1804 Inner Wheel Bearing Cup Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50396 Inner Wheel Bearing Cup a simple and fast procedure
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1505 Front Wheel Seal Installer Is custom made to quickly and easily install your new wheel seals without damaging them
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals (Individual)

top_page
product note
Ford used only the best wheel bearings and seals money could buy to equip their Dana 50 IFS front axles to minimize the chance for warranty problems. That is why they chose Timken® Wheel Bearings and Spicer Wheel Seals for heavy-duty Ford F-250 and F-350 4x4s using the IFS Dana 50. We supply those exact original equipment replacement Timken® Wheel Bearings and Spicer Wheel Seals to keep your Ford on the job for years to come
photo
QU50411 Timken® Outer Wheel Bearing Cup For all 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4 Dana 50 IFS front drive axles.

Link to our large text QU50411 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50412 Timken® Outer Wheel Bearing For all 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4 Dana 50 IFS front drive axles.

Link to our large text QU50412 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50396 Timken® Inner Wheel Bearing Cup For all 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4 Dana 50 IFS front drive axles.

Link to our large text QU50396 catalog page.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50398 Timken® Inner Wheel Bearing For all 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4 Dana 50 IFS front drive axles.

Link to our large text QU50398 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40119 Inner Wheel Seal Is a genuine Dana-Spicer original equipment replacement part for all 1983.5-1997 F-250 and 1983.5-1985.5 F-350 4x4 Dana 50 IFS front drive axles.

Link to our large text QU40119 catalog page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
product note
Ford used the same wheel bearing and seal numbers for the entire 1983 to 1997 production run of Dana 50IFS front drive axles. However, spindle nut sets will vary by year. We offer Wheel Bearing Part/Tool Kits with or without bearing and seal installation tools. If you need a spindle nut socket, see QT1025 for 1983-1985.5 trucks or QT1110 for 1985.5-1997 models with manual hubs or QT1058 Rounded Hex Spindle Nut Socket for 1994-1997 trucks with factory auto locking hubs
photo
TK4744 Torque King® 1983-1997 Front Wheel Bearing and Seal Kit without Tools Is a parts only (No Tools) Complete Front Wheel Bearing and Seal Kit for your heavy-duty Ford featuring Timken® Bearings and original equipment wheel seals for all 1983-1997 Ford heavy duty 3/4 ton & 1 ton 4x4 trucks with open knuckle Dana 50 IFS front drive axles. Kit includes 2 each of Timken® Inner and Outer Wheel Bearings/Bearing Cups, plus two Wheel Seals.

Link to our large text TK4744 catalog page.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK4738 Torque King® 1983-1997 Front Wheel Bearing and Seal Kit with Install Tools For all 1983-1997 Ford heavy duty 3/4 ton & 1 ton 4x4 trucks with open knuckle Dana 50 IFS front drive axles. Kit includes Inner Wheel Bearing Cup Installer, Outer Wheel Bearing Cup Installer, Wheel Seal Installer, Driver Handle, plus 2 each of Timken® Inner and Outer Wheel Bearings/Bearing Cups, plus two Wheel Seals. This Kit DOES NOT INCLUDE Spindle Nut Socket or Hub Small Parts for your Ford!!!

Link to our large text TK4738 catalog page.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!