Parts for Dana-Spicer Model 60 Front Axles in 1985-1991 Ford F-350 4x4 Trucks

We stock a wide selection of parts and Tools for 1985 to 1991 Ford F-350 Dana 60 open knuckle front drive axles with King Pins. The open knuckle, monobeam, Dana-Spicer Model 60 was reintroduced by Ford as a mid-year design change in the 1985 model year F-350 1 ton 4x4, replacing the Twin Traction Beam IFS Dana 50 4600 pound rated axle which was used on F-350 trucks starting in the 1980 model year. The newly reintroduced Dana 60 King Pin drive front axle axle, had a weight rating of 5000 pounds (the previous 1978-1979 Ford Dana 60 was rated for 4500 pounds).

The new 1985 Ford Dana 60 was slightly wider than the 1978-1979 models but otherwise quite similar to the earlier version with the exception of a dual wheel option and different brake components. With the 5000 pound Dana 60, Ford F-350 1 ton trucks once again offered a viable alternative to Dodge W-350 and GM K3500 1 ton trucks, both of which had 4500 pound rated King Pin type Dana 60 solid beam axles since the mid 1970's.

Starting mid-way in the 1988 model year, Ford's F-350 front Dana 60 had some axle shaft design changes, but almost all the other parts remained the same through the end of the 1991 model year.

The King Pin Model 60 stayed in the Ford lineup as the only available front drive axle for the F-350 until the end of the 1991 model year. Ford switched to a ball joint Model 60 for the 1992 model year.

Axle Identification

top_page
photo
All 1985-1991 Dana 60 Front Axles in Ford Trucks had a Ford Axle Code Tag with the Ford Production Part Number and Dana Bill of Material Number (BOM) stamped on a metal Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows) when the vehicle was shipped from the factory but, unfortunately, these tags are often missing on trucks that had prior differential service. The BOM number is a 6 digit number beginning with a 6 plus a dash number (ex: 610604-2). They can be used to determine not only the axle model, but also what components the axle was originally built with. We often ask for this number to insure we provide you with the exact parts you need for your truck.

Each different BOM number signifies an engineering part change which may be minor or major and may involve one or more parts. The dash number indicates the axle ratio and, for some years, the front wheel hub style (for single or dual rear wheel models).

photo
The 1985 to 1991 Ford Dana 60 axles have a unique to Ford, reverse spiral ring and pinion set available in either 3.54 or 4.10 gear ratios.
Cover: 10 Bolt, 12" high
Ring Gear: 9-7/8", 12 Bolt
Suspension: Leaf spring
Axle Shafts: 1985 to 1991 axle shafts are 1-5/16" 30 spline and the 1-3/8" axle u-joint cups are retained by c-clips that seat against the inside of the axle shaft yoke ears
Knuckle Mounting: Open with Greaseable King Pins. Upper uses spring loaded plastic bushing rotating on a tapered King Pin. Lower has taper roller bearing
Wheel Hub: 1985-1991 Ford Model 60 axles have an internally splined hub in which a splined drive gear or lockout hub assembly would fit into
1980-1984 Bill of Material Numbers Ford did not use the Dana 60 Front Axle for these years!
1985-1987 Bill of Material Numbers 1985: 610220
1986-1987: 610255
1988 Bill of Material Numbers 1988: 610255, 610355
1988.5: 610313
1989-1991 Bill of Material Numbers Model 60: 610313 for all years

Axle Shafts

top_page
product note

All our Ford F-350 Dana 60 front axle shafts are brand new, genuine original equipment replacement parts for maximum strength. There was a change in axle shaft lengths and outer axle shafts, but I have not been able to establish the exact date of the axle shaft changeover, as the Dana and Ford parts application information does not agree. So if you have a 1988 to 1991 F-350, you will need to verify which parts you need!

photo
QU40486 30 spline 1985-1988.5 Ford F-350 Dana 60 Outer Axle Shaft For 1985 to 1988.5 F-350 4x4 trucks trucks with Dana 60 Front Axles. The snap ring groove is at the outboard end of the splines
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40329 35 Spline 1985 to 1988.5 Ford F-350 Dana 60 Left Inner Axle Shaft For 1985 to Early 1988 Ford F-350 4x4 single rear wheel and dual rear wheel trucks all of which have Dana 60 Front Axles
photo

QU40532 35 Spline 1985 to 1988.5 Ford F-350 Dana 60 Right Inner Axle Shaft For 1985 to 1988.5 Ford F-350 4x4 single rear wheel and dual rear wheel trucks all of which have Dana 60 Front Axles.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40371 1988.5-1991 30 Spline Ford F-350 Dana 60 Outer Axle Shaft For Late 1988 to 1991 Ford F-350 4x4 trucks with either single rear wheel or dual rear wheel trucks all of which have Dana 60 Front Axles, The snap ring groove is at the inboard end of the splines
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40487 1988.5-1991 35 Spline Ford Ford Dana 60 Left Inner Axle Shaft For 1988.5 to 1991 Ford F-350 4x4 single rear wheel and dual rear wheel trucks all of which have Dana 60 Front Axles
photo

QU40526 1988.5-1991 35 Spline Ford F-350 Dana 60 Right Inner Axle Shaft For 1988.5 to 1991 Ford F-350 4x4 with either single rear wheel and dual rear wheels all of which have Dana 60 Front Axles.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK42163 Spicer Nickel Chromoly High Performance 35 Spline Right or Left Inner Axle Shaft for Dana 60 1984-1988 Ford.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Seals and Seal Kits for Inner Alex Shafts

top_page
product note

On 1985 to 1991 Ford F-350 Dana 60 front axles, an Inner Axle Seal is pressed in the inboard end of each axle tube, right next to the differential side bearings. These seals contact the inner axle shafts to prevent gear oil from running out of the differential and down the axle tubes. Old age, blown axle u-joints, and/or grit that works it's way into the axle tubes and cuts the seal are the usual causes of failure. A bad Inner Axle Shaft Seal can be detected by oil coming out the end of the axle tubes next to the axle shaft u-joint. Usually when these Seals start to fail, they will seep oil so the leakage may go unnoticed for quite some time. Many a ring and pinion set has been burned up from axles that lost all their lube when long term seepage was not seen.

photo
QK4656 Adjustable Depth Type Inner Axle Shaft Seal Tool and Seal Kit For 1985-1991 Ford F-350 1 ton 4x4 trucks. Kit includes Installation Tools and two Seals
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4656 Adjustable Depth Type Inner Axle Shaft Seal Tool Set 1985-1991 Ford F-350 1 ton 4x4 trucks. Includes Installation Tools only, Purchase QU40059 Axle Seals separately
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40059 1985-1991 Ford Dana 60 Inner Axle Shaft Seal One of these Seals are installed in each axle tube, right next to the differential to keep gear lube from leaking out the ends of the axle housing on all 1985-1991 Ford F-350 1 ton 4x4 trucks
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40459 1988.5-1991 Ford F-350 Dana 60 Outboard Axle Shaft to Axle Housing Seal Installs on inner shaft next to the yoke on those inner axle shafts with a step machined next to the yoke for this seal. It's function is to keep dust and debris from entering the axle housing tubes. This is only a Dust Seal. If you see oil leaking past this seal, you need QU40059 Inner Axle Seal.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note

We offer three different Universal Joints for your hard working Ford 4x4 Truck. All are plenty strong for the job, but different manufacturing techniques and seal types will have a major influence on the ultimate life of the joint. Our most popular choice is our TK40715 cold-forged, non-greaseable, original equipment replacement U-Joint. The wear-resistant cold-forged cross and superior sealing make it the best choice for both low maintenance and long life. Greaseable TK40724 U-Joints are a greaseable version of our TK40715 joints, giving you the durability advantages of cold-forging and better seals with the option to re-lube the joint at any time for unmatched longevity. QU30332 's are hot-forged and equipped with simple rubber seals. With good maintenance and quality lubricant like our Pyroplex® Plus Grease, these joints will last and last. See our individual product pages for more info

photo
QU30332 Greaseable Axle U-Joint for 1985-1991 Ford F-350 Dana-Spicer Model 60 Front Axle Value priced with Hot-Forged cross and flexible rubber seals
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK40724 Torque King® Ford F-350 Dana 60 Greaseable Axle U-Joint Premium Cold-Forged cross and superior pressure-type seals, plus it is greaseable for unmatched life and durability!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK40715 Torque King® Ford F-350 Dana 60 Premium Non-Greaseable Axle U-Joint Original equipment type universal joint with Premium Cold-Forged cross and superior pressure-type seals
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK42117 Greaseable and Rebuildable CTM 1480WJ Series Performance Axle U-Joint for Ford F350 Dana 60 Beam Type Front Axles.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
product note
Our stock of Ford F-350 front brake parts is limited. The front brakes on the 1985-1991 F-350 4x4 trucks utilized dual piston calipers and good sized brake pads. For the most part, the front brakes generally gave pretty good service that was comparable to the contemporary Dodge and GM 4x4's with one exception. We saw a lot higher percentage of Fords with warped or cracked brake rotors compared to the competition. Whether this was due to the somewhat thinner Ford brake rotor thickness or our Ford customers were harder on their brakes, I can't say, but a F-350 that was used to frequently tow a trailer always seemed to need rotors
photo
QU20284 1985-1991 Left Front Brake Splash Shield Is a genuine original equipment part for 1985-1991 Ford F350 Dana 60 Monobeam front axles. Link to our large text individual QU20284 detail page.
Also available while supplies last: QU20284U Good Used 1980-1994 Left Front Brake Splash Shield
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20285 1985-1991 Right Front Brake Splash Shield Is a genuine original equipment part for 1985-1991 Ford F350 Dana 60 Monobeam front axles. Link to our large text individual QU20285 detail page.
Also available while supplies last: QU20285U Good Used 1980-1994 Right Front Brake Splash Shield
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings (Individual)

top_page
product note
If you only need a bearing or two for your 1985-1991 Ford F-350 Dana 60 diff, we stock the best: Timken®. For the amount of work it takes to change most axle bearings, the extra cost for a Timken® diff or pinion bearing is a small price to pay for better steel, more uniform surface finish, and accurate, precision ground races
photo
QU50397 Timken® Differential Bearing Cup For all 1985-1991 Ford Dana-Spicer Model 60 Front Axles. Use 2 per axle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50398 Timken® Differential Bearing For all 1985-1991 Ford Dana-Spicer Model 60 Front Axles. Use 2 per axle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50400 Timken® Outer Pinion Bearing Cup For all 1985-1991 Ford Dana-Spicer Model 60 Front Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50401 Timken® Outer Pinion Bearing For all 1985-1991 Ford Dana-Spicer Model 60 Front Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50406 Timken® Inner Pinion Bearing Cup For all 1985-1991 Ford Dana-Spicer Model 60 Front Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50407 Timken® Inner Pinion Bearing For all 1985-1991 Ford Dana-Spicer Model 60 Front Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing and Seal Kits

top_page
product note
Torque King® Premium Diff Bearing and Seal Kits are the #1 choice for those who depend upon their truck to keep working day in and day out no matter how tough the conditions. Our Kits combine the superb quality of Timken® bearings with the precise fit and reliability of 100% genuine Dana-Spicer small parts. No aftermarket, off brand or Chinese knockoff parts in these Kits!
photo
TK4864 Torque King® Premium Quality Front Differential Bearing and Seal Kit For your 1985-1991 Ford F-350 heavy-duty 4x4 truck features 100% Timken® Bearings and genuine Dana-Spicer Pinion Seal, and pinion small parts.

Dan the Gear Man® Product Note: TK4864 Kit does NOT include QU40160 (1976-1977) or QU40059 (1978-1991) Axle Shaft Seals. Order those axle shaft oils seals separately or order QU40059 Seals as part of QK4656 Axle Shaft Seal Kit.
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK4875 Torque King® Premium Quality Front Differential Master Service Kit For your 1985-1991 Ford F-350 heavy-duty 4x4 truck features 100% Timken® Bearings and genuine Dana-Spicer Small Parts, Seals, and Shims.

Dan the Gear Man® Product Note: This Kit does not include QU40041 Side Gear Thrust Washers, or QU40518 Pinion Mate Gear Thrust Washers
photo
QU40184 Timken® Differential Bearing Cup and Bearing Set Includes two each QU50397 Differential Bearing Cup and QU50398 Differential Bearing
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50491 Differential Bearing & Seal Kit for Dana Model 60 Front Axles in 1985-1991 Ford F-350 4x4 trucks. This kit includes: QU50400 Outer Pinion Bearing Cup, QU50401 Outer Pinion Bearing, QU50406 Inner Pinion Bearing Cup, QU50407 Inner Pinion Bearing, 2 QU50397 Differential Bearing Cups, 2 QU50398 Differential Bearings; QU51065 early and QU50565 late, aftermarket pinion seal; QU50566 aftermarket pinion nut, QU50567 aftermarket differential and pinion shim kit; and QU90009 axle service pack. Contains USA and imported parts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
product note
Differential problems with Model 60 front axles are not all that common. But Murphy, of Murphy's Law* really likes busted differentials, so when you hear that loud, heart-stopping, ominous BANG from the front axle as your 4x4 lurches to a grinding stop, you just KNOW it is one big dose of bad news. To help get you back on the road after you get rescued, we stock genuine original equipment Dana-Spicer Front Axle Differential Parts for your hard working 1 ton F-350 4x4 truck.
*Murphy's Law: "Anything that can go wrong, will go wrong"
photo
QU40254 Ford F-350 Bare Differential Case Kit Is a genuine Dana-Spicer Model 60 Case for 3.54 and 4.10 ratio ring and pinion sets. Kit includes Bare Open Differential Case, 12 QU40086 Ring Gear Bolts and QU40206 Differential Shim Kit
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20271U Good Used Differential Case Dana Model 60 is a genuine Dana-Spicer part. QU20271U fits many Dana-Spicer Model 60 front or rear axles with open differentials and 4.30 or numerically lower gear ratios (ex: 3.54). Also fits some Model 61 axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40331 Dana 60 35 Spline Ford F-350 Differential Inner Parts Kit includes 2 differential side gears, 2 QU40518 pinion mate thrust washers, 2 differential pinion mate gears, 2 QU40041 side gear thrust washers, QU40520 differential cross shaft, QU40519 cross shaft retaining pin, 12 QU40086 ring gear bolts, and differential adjusting shims
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40518 Ford F-350 Dana 60 Differential Pinion Mate Thrust Washer Two of these genuine original equipment Thrust Washers are used in each differential, one between each pinion mate gear and the differential case
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40041 Ford F-350 Dana 60 Differential Side Gear Thrust Washer Two of these genuine original equipment Thrust Washers are used in each differential, one between each side gear and the differential case
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40520 Ford F-350 Dana 60 Differential Cross Shaft Is a genuine original equipment Cross Shaft that supports the two differential pinion mate gears
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40519 Lock Pin for Differential Cross Shaft Is used to lock QU40520 differential cross shaft to the differential case.>
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Makers

top_page
product note
In the mid 1970's Dana made a differential cover design change to heavy gauge covers with flat mating flanges. Unlike the previous, thin gauge covers with embossed flanges which were made for use with a cut gasket, the new design, thick gauge covers are designed for sealing with RTV. If you desire, you can still use a gasket with the new type cover by combining the gasket with thin films of RTV. We stock both Ultra Gray RTV Sealant and genuine Dana Gaskets.
photo
QU40367 Rear Differential Cover Gasket For Model 70 Axles. These genuine Dana-Spicer gaskets will also work on your Dana 60 front axles if you wish to use a Gasket in lieu of RTV sealant.

Dan the Gear Man® Tech Note: RTV sealant instead of Gaskets were used during the factory assembly of your axle.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Ford F-350.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hubs and Hub Parts

top_page
product note

There were at least four different Hub and Rotors for 1985-1991 Ford F-350 trucks. All are out of production, but what units we have will be listed at the end of this section. Ford used both auto and manual hub-locks for 1985 to 1991 era F-350 front axles. The Auto Hubs came out I think in 1988, but Ford never supported them much for replacement parts, so most Auto Hubs have long since been replaced by manual units which are both cheaper and far more reliable. We stock parts for the Red or Black plastic Dial Warn manual hubs used on factory manual hub equipped 1985 to 1991 F-350 4x4s. Mechanically, this is the same Warn hub as the sold by the aftermarket with a black plastic dial for the 1985-1991 model years

photo

TKA20332/QU20332U Front Hubs for 1988-1991 F350 chose from either new or good used Ford splined Front Hub for 1985-1991 Ford F-350 4x4 trucks with Dana 60 5000 pound front axles.
More Info

photo

QU20355 9/16" Front Wheel Stud for 1985-1991 F350 Is a hardened, fine thread replacement front wheel stud for all 1992-1997 Ford F350 4x4 trucks with 9/16" wheel studs

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56025 Warn 38826 Premium Hub Set for Dana 60 Front Axles with internally splined front wheel hubs. A sharp looking and reliable hub. QU56025 Fits Ford F-350 Dana 60 1985-1991

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56011 Warn® Dana 60 Internal Spline Mount Hub Locks for 1985 to 1991 Ford F350 Dana 60 front axles. QU56011 is the current production version of the Warn's original equipment 1980-1994 Ford Hub-Lock.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU42116 30 Spline Drive Gear Kit for 1980-1982 Ford Dana 50IFS Front Axles with internal splined wheel hubs.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4916 Hub Service Kit For QU56011 Lockout Hubs includes 2 QU56017 Spiral Retaining Rings, 2 QU56016 O-Rings, 2 QU40068 Axle Shaft Snap Rings, 12 QU56012 Hub Screws, and 1 Set Replacement Decals.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56013 Warn® Dial Assembly For Original Equipment Spline Mount Hubs used in Ford F-350 Dana 60 Front Axles
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56012 Original Equipment Warn® Hub Screw For Warn® Spline Mount Hubs in Ford F-350 Dana 60 Front Axles.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40113 Torx® Upgrade Screw For Warn® Spline Mount Hubs in Ford F-350 Dana 60 Front Axles
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56015 Replacement Decals for Warn® Plastic Hub Dials.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50116 QUAD-Ring square cross section sealing ring for Factory Warn® Spline Mount Hubs in Ford F-350 Dana 60 Front Axles.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50240 O-Ring for Warn® Spline Mount Hub Dials in Ford F-350 Dana 60 Front Axles.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40068 Axle Shaft Snap Ring Fits in the groove machined at the end of the outer axle shaft splines in Ford F-350 Dana 60 Front Axles.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40150 Lockout Hub to Wheel Hub Snap Ring For Warn® Spline Mount Hubs used in Ford F-350 Dana 60 Front Axles.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56016 O-Ring for Warn® Current Production Spline Mount Replacement Hubs.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56017 Warn® Spiral Retaining Ring for Current Production Spline Mount Replacement Hubs.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

King Pin Kits and Parts

top_page
product note
We stock all the normal replacement parts for Dana 60 King Pin type Front Axles. 1985 to 1991 Ford Dana 60 front axles use greaseable and rebuildable King Pins instead of Ball Joints to mount the steering knuckles to the axle housing. Time has proven the Dana 60 King Pin design to be the most durable front axle steering components ever installed in Class 2 3/4 ton and Class 3 1 ton 4x4 trucks. Although at first glance the number of King Pin parts may appear daunting, the fact is King Pins front axle components are usually pretty easy to replace if they ever need service beyond regular greasing
photo
QK4512 Dana Model 60 King Pin Kit For 1985-1991 Ford F-350 1 ton 4x4 trucks with Model 60 King Pin type front axles. Kit includes lower king pin bearing assemblies, king pin seals, lower king pin grease retainers, upper king pin bushings, tension springs, spring plates, anti-seize, Threadlocker, disc brake lube, RTV sealant, & cotter keys for the tie rod ends
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40191 Dana 60 Lower King Pin Bearing and Seal Kit For 1985-1991 Ford F-350 1 ton 4x4 trucks equipped with Dana Spicer Model 60 front drive axles includes one each these genuine Dana replacement parts: QU40062 Lower Grease Retainer, QU50600 Lower King Pin Bearing, QU50601 Lower King Pin Bearing Cup, QU40092 Lower King Pin Seal, QU40147 Upper King Pin Seal. Order two Kits per vehicle. Also See QK4512 King Pin Kit
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4550 Dana 60 Upper King Pin and Wrench Set Includes 3/4" Drive Impact Socket/Hex Bit Socket, 2 genuine Dana Spicer Upper King Pins, and S9979 High Strength Threadlocker
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40266 Dana 60 Upper King Pin Is a genuine Dana Spicer service part for your 1985-1991 Ford F-350 1 ton 4x4 truck's Dana 60 open knuckle, king pin front end
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40157 Dana 60 Upper King Pin Spring Retainer Plate Is a genuine Dana Spicer replacement part for 1985 to 1991 1 ton and heavy duty 3/4 ton 4x4s equipped with Dana Spicer Model 60 front drive axles. This Retainer Plate fits between QU40265 Tension Spring and QU40093 Upper King Pin Bushing. The raised inner rim keeps the Spring centered over the bushing. Made in U.S.A. Also see QK4512 King Pin Kit
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40265 Dana 60 Upper King Pin Spring This genuine original equipment Dana Spicer heavy-duty coil spring applies constant tension to QU40093 Upper King Pin Bushing to automatically adjust for wear and dampen road shock. QU40265 fits 1985-1991 Ford F-350 1 ton 4x4 trucks equipped with the Dana Spicer Model 60, open knuckle front axle with King Pins
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40093 Dana 60 Plastic Upper King Pin Bushing This long lasting, genuine original equipment Dana Spicer split plastic bushing has a tapered ID to match QU40266 Upper King Pin. QU40265 fits 1985-1991 Ford F-350 1 ton 4x4 trucks equipped with either the Dana Spicer Model 60, open knuckle front axles with King Pins. Also see QK4512 King Pin Kit
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40147 Dana 60 Upper King Pin Seal Is a genuine Dana Spicer service part for all 1985-1991 Ford F-350 1 ton 4x4 trucks with Model 60 open knuckle front drive axles. Also see QK4512 and QU40191 King Pin Kits
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40063 Dana 60 Upper King Pin Gasket Is a genuine Dana Spicer replacement Gasket for all 1985-1991 King Pin type Model 60 open knuckle front drive axles. A high quality cut gasket that seals between your steering knuckle and upper king pan cap/steering arm. Use two QU40063 Gaskets per vehicle. Made in Indonesia. Also see QK4512 King Pin Kit
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40062 Dana 60 Lower King Pin Grease Retainer Is a genuine Dana Spicer service part for all 1985-1991 Ford F-350 1 ton 4x4 trucks with King Pin type Dana 60 open knuckle front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50600 Large King Pin Bearing for Dana Heavy Duty Front Axles For all 1985-1991 Ford F-350 1 ton 4x4 trucks with Dana Model 60 open knuckle front drive axles. Also see QK4512 and QU40191 King Pin Kits
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50601 King Pin Bearing Cup for Dana 60 and Dana 70 Front Axles For all 1985-1991 Ford F-350 1 ton 4x4 trucks with Model 60 open knuckle front drive axles. Also see QK4512 and QU40191 King Pin Kits
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40092 Dana 60 Lower King Pin Seal Is a genuine Dana Spicer service part for all 1985-1991 Ford F-350 1 ton 4x4 trucks with Dana Model 60 open knuckle front drive axles. Also see QK4512 and QU40191 King Pin Kits
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU30064 Dana 60 Upper King Pin Cap/Steering Arm Stud Is a genuine original equipment replacement part for securing the drivers side steering arm to the steering knuckle on all 1985-1991 Ford F-350 1 ton 4x4 trucks Model 60 open knuckle front drive axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals and Technical Information

top_page
product note
Dan the Gear Man® Product Note: Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations.
photo
TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
VSG4506 Model 60 King Pin Service Video (Previously named QK4512DVD or V4512DVD) shows you how to perform King Pin Service on your 1985-1991 Dodge Model 60 open knuckle 4x4 front drive axle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts

top_page
product note
Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings
photo
S24200 Blue Threadlocker For spindle and ring gear bolts etc
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90018 Pyroplex Protection ES Synthetic Grease Provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions!
photo
QU90016 SynPower ® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90015 Syncon High Performance Synthetic Arctic Grease Is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90017 Red Grease Is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. cartridge or 1 pound tub
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals and Pinion Yokes

top_page
product note
Ford used 2 different Pinion Yokes on 1985-1991 era F-350 4x4 Dana 60 Front Axles. The two yokes are identical except for the slinger (deflector). Some of the 1985 pinion yoke units have a U-shaped QU40401 Slinger. All the other trucks use QU20179 pinion yokes which has a cone shaped deflector. Both original equipment pinion yokes use QU40841 U-bolts to secure the oversize 1.125" u-joint cups used on the Ford specific 1330F universal joints (See TK40723 and QU40776 ). The original QU20179 1330F Pinion Yokes are now out of production although we still have some available as of September 2011. A less expensive and more readily available alternative to the original yoke is to replace the 1330F u-joint with a straight 1330 U-joint (TK40721, (QU40774 ) and use either QU40509 or QU40713 1330 series pinion yokes
photo
QU40097 Ford F-350 Dana 60 Front Axle Pinion Seal This genuine Dana-Spicer original equipment pinion seal fits all 1985-1991 Ford F-350 1 ton 4x4 trucks Model 60 open knuckle front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20179 1330F Front Dana 60 Pinion Yoke Is a genuine original equipment replacement pinion yoke for 1985-1991 Ford F-350 Dana 60 axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40841 Driveshaft U-Bolt Kit for Ford F-350 Dana 60 Front Axle Fits all 1985-1991 Ford original equipment Front Dana 60 pinion yokes including QU20179.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40509 1330 Series 1985 Dana 60 Pinion Yoke Is a that takes standard 1330 series universal joints for 1985 F-350 4x4s originally equipped with a now discontinued 1330F yoke having a u-shaped slinger. Requires changing your matching u-joint to TK40721 or QU40774 and purchasing QU40735 Strap and Bolt Kit
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40713 1330 Series 1985-1991 Dana 60 Pinion Yoke Is a lower cost option than QU20179 that takes standard 1330 series universal joints for 1985-1991 F-350 4x4s originally equipped with QU20179 1330F pinion yoke having a cone shaped shaped deflector
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40735 Universal Joint Strap and Bolt Kit for QU40509 and QU40713 1330 Pinion Yokes This genuine Spicer original equipment Kit is used to secure Spicer type universal joints with 1-1/16" diameter cups to Dana 60 axle pinion yokes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
product note

1985-1991 Ford F-350 front Dana 60 axles have reverse spiral pinion gears that are set above the axle center line. The reverse spiral gearsets are probably not quite as strong as the standard cut gearing, but the high pinion significantly reduces front driveshaft angles and the extra ground clearance helps keep the pinion yoke and front driveshaft u-joint out of harm's way. The standard cut and reverse spiral gearsets ARE NOT INTERCHANGEABLE!

photo
QU40620 3.54 Ratio Ford Dana 60 Ring and Pinion Set For 1985-1991 Dana 60 front axles in Ford F350 4x4 trucks. QU40620 3.54 ratio Ring and Pinion Kit is a genuine Dana reverse spiral gear set with pinion bearings, pinion seal, ring gear bolts, pinion nut, pinion washer, diff cover gasket, small parts, and shims
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20337U Good Used Ring 4.10 Ratio Ring and Pinion Set for 1978-1997 Ford Dana 60 axles.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note
Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else
photo
QU40064 Ford F-350 Slinger for Outer Axle Shaft presses on your 1985-1991 Ford F-350 1 ton 4x4 truck's Dana 60 outer axle shaft and acts as both the mounting surface and protective slinger for QU40065 Spindle V-Seal
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40343 Ford F-350 Dana 60 Hardened Differential Cap Retaining Bolt Genuine original equipment hex-head bolt for Dana Spicer Model 60 front axle differential bearing caps fits all 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40022 Ford F-350 Dana 60 Pinion Nut Genuine original equipment pinion nut for Dana Spicer Model 60 axle differential bearing caps fits all 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle. QU40022 is a genuine original equipment, self-locking nut, intended for a single use part, discard and replace with a new nut any time you remove the pinion nut.

Also included in TK4864 and TK4875

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40023 Dana 60 Pinion Washer for Ford F-350 Is a genuine original equipment flat washer goes between the pinion nut and pinion yoke. all 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle.

Also included in TK4864 and TK4875

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40030 Ford F-350 Dana 60 Inner Pinion Oil Baffle Is a genuine original equipment part that is installed in the inner pinion bearing cup housing bore along with the pinion depth shims and QU50406 inner pinion bearing cup. The Baffle almost always gets mashed when you are replacing the inner pinion bearing cup
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50503 Ford F-350 Dana 60 Inner Pinion Oil Slinger Is installed between the pinion head and QU50407 Inner Pinion Bearing
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40207 Ford F-350 Dana 60 Differential and Pinion Shim Kit For Dana-Spicer Model 60 front axles in 1985-1991 Ford F-350 1 ton 4x4 heavy duty 4x4s. Genuine Dana-Spicer Shim Kit includes Pinion depth shims, pinion preload shims, differential adjusting shims, pinion nut, and cover gasket
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40206 Ford F-350 Dana 60 Differential Bearing Shim Kit Includes a selection of genuine original equipment Shims for adjusting backlash and differential bearing preload on your 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle.

Also included in TK4875 and QU40207

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40099 Ford F-350 Dana 60 Outer Pinion Slinger Fits between the outer Pinion Bearing and Pinion Yoke. QU40099 is a genuine original equipment Dana Spicer part. Fits all 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle.

Also included in TK4864 and TK4875

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40086 Ford F-350 Dana 60 Ring Gear Bolt For Dana 60 front axles. Genuine Dana-Spicer Grade 9 Bolt has locking teeth under the hex head to prevent loosening under any load conditions.

Also included in TK4875

Dan the Gear Man® Safety Note: Ring Gear Bolts are designed for a single use. They must be replaced after they are removed!

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU30064 Dana 60 Upper King Pin Cap/Steering Arm Stud Is a genuine original equipment replacement part for securing the drivers side steering arm to the steering knuckle on all 1985-1991 Ford F-350 1 ton 4x4 trucks Model 60 open knuckle front drive axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindles and Spindle Nuts

top_page
product note

According to Dana-Spicer, they supplied two front spindle nut types for 1985-1991 F-350 Dana 60 Front Axles. The Dana parts lists shows 1985 model year Dana 60 front axles will have a 6 slot spindle nut set with a thrust washer and bend over tab lockwasher (A carry-over design from the 1970's). Ford Parts lists, however show the 1985 axle used the same 4 slot spindle nut set as 1986-1991 year trucks. So, if you have a 1985 axle, you need to verify what parts YOUR axle has. There is no question 1986-1991 axles were built with a 4 slot double nut set with a perforated washer lock larger than, but similar to the nut sets Ford used in Dana 44 axles as far back as 1959.

photo
QU40036 Ford F-350 Dana 60 6 Slot Spindle Nut For 1985 4x4 F-350 is a genuine original equipment replacement nut for either the inner or outer front spindle nut for the Dana 60 front axle in 1985 F350 4x4 trucks. Order 2 Nuts per side
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40037 Ford F-350 Dana 60 Spindle Lockwasher for 6 Slot Spindle Nuts For 1985 4x4 Ford F-350 trucks. QU40037 is a genuine original equipment replacement lockwasher that fits between the inner and outer front spindle nut on the Dana 60 front axle
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40038 Ford F-350 Dana 60 Inner Thrust Washer for 6 Slot Spindle Nut S used on 1985 4x4 F-350s. QU40038 is a genuine original equipment replacement Thrust Washer that goes between inner front spindle nut and outer wheel bearing on the Dana 60 front axle
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4728 Ford F-350 Dana 60 Round, 6 Slot Spindle Nut Kit For 1985 F-350 includes QU40038 Inner Thrust Washer, Two QU40036 6 Slot Spindle Nuts, and QU40037 Bend Over Tab Spindle Lock Washer
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40163 Ford F-350 Round Outer Spindle Nut For 1986-1991 Ford F-350 4x4 has 4 slots for QT1018 Spindle Nut Wrench
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40164 Ford F-350 Spindle Lock Washer For 1986-1991 Ford F-350 4x4 with round spindle nuts is reusable
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40166 Ford F-350 Round Inner Spindle Nut with Pin For 1986-1991 Ford F-350 4x4 has 4 slots for QT1018 Spindle Nut Wrench. Includes round pin that engages one of the holes in QU40164 Spindle Lock Washer
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4729 Ford F-350 Round Spindle Nut Kit for 1986-1991 Ford F-350 4x4 includes one each QU40163, QU40164, and QU40166
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU95036 Heat-treated, All Metal, Spindle to the Steering Knuckle Lock Nut Six of these USA Made, 150, 000 psi rated Locknuts fit on QU40540 Spindle to Knuckle Bolt to secure each of your front Spindles to the Steering Knuckles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40540 Spindle-to-Knuckle Bolt Five of these press-in special bolts fit each steering knuckle on 1985-1991 Ford F-350 Dana 60 Front Axles. They are used along with QU95036 Locknut to retain your spindles and caliper anchor plates
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40169 1985-1991 Ford Dana F-350 60 Front Spindle Kits include new Spindle, Spindle Thrust washer, Large Spindle V-Seal, plus pre-installed Spindle Bearing and Spindle V-Seal. QU40169 is a genuine Dana factory part.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Y440169 1985-1991 Ford Dana F-350 60 Front Spindle Kits include new Spindle, Spindle Thrust washer, Large Spindle V-Seal, plus pre-installed Spindle Bearing and Spindle V-Seal. Y440169 is a high quality replacement.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Bearings and Seals

top_page
product note

The dead, hollow spindle design of the 1985-1991 era Ford F-350 Dana 60 series axles uses QU40149 needle bearing to support the outer axle shaft. Axial thrust is handled by a plastic thrustwasher. Two V-Seals are used to protect the spindle bearing. We stock all the individual components, plus Kits combining the pieces

photo
QU40064 1985-1991 Ford F-350 Outer Axle Shaft Slinger Is a genuine Dana Spicer part that press fits on the outer axle shafts of Model 60 open knuckle front drive axles for your 1985-1991 Ford F-350 4x4.

Please refer to QU40064 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40065 Large Spindle V-Seal is a genuine Dana Spicer part that fits between the spindle and QU40064 outer axle shaft slinger in Model 60 open knuckle front drive axles on your 1985-1991 Ford F-350 4x4
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40066 1985-1991 Ford F-350 Dana 60 Outer Axle Shaft to Spindle Thrust Washer Is a genuine Dana Spicer part that fits on your Dana 60 outer axle shaft to control thrust between the axle shaft and spindle.

Please refer to QU40066 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40148 1985-1991 Ford F-350 Dana 60 Small Spindle V-Seal Is a genuine Dana Spicer part that fits in the back of your spindle between QU40149 spindle bearing and QU40066 thrust washer in Model 60 open knuckle front drive axles on your 1985-1991 Ford F-350 4x4.

Please refer to QU40148 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40149 1985-1991 Ford F-350 Dana 60 Spindle Bearing Is a genuine Dana Spicer original equipment part that is a press fit in the back of the spindle. This bearing is the primary support for your outer axle shaft.

Please refer to QU40149 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40168 1985-1991 Ford F-350 Dana 60 Spindle Bearing and Seal Kit Services ONE side of your 4x4 with one each of these parts: QU40065 Large Spindle V-seal, QU40066 Spindle Thrust Washer, QU40148 Small Spindle V-seal, and QU40149 Spindle Bearing.

Please refer to QU40168 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Knuckles

top_page
photo
QU30064 Dana 60 Upper King Pin Cap/Steering Arm Stud Is a genuine original equipment replacement part for securing the drivers side steering arm to the steering knuckle on all 1985-1991 Ford F-350 1 ton 4x4 trucks Model 60 open knuckle front drive axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note
Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 60 front axle in your 1985-1991 Ford F-350
photo
QT1064 Dana 60 Upper King Pin Wrench Removes and installs the upper king pin cones on Dana 60 front axles in 1985 to 1991 Ford F-350 4x4 trucks
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT5500 Wheel Bearing Packer Takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your big Ford!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4656 Dana 60 Adjustable Depth Type Inner Axle Shaft Seal Tool Set for 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle. Includes QT1042 Adjustable Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate. Purchase QU40059 Axle Seals separately
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1133 Dana 60 Inner Axle Seal Press Screw Assembly For installing QU40059 Inner Axle Seals in 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle. Use with the QT1042 or QT1156 Seal Installers and QT1130 Thrust Plate Thrust Plate. Also see TS4656 and TS4867 Inner Axle Seal Installer Tool Sets
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1042 Dana 60 Adjustable Depth Inner Axle Seal Installer Also see TS4656 Inner Axle Seal Installer Tool Set
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1130 Dana 60 Thrust Plate Fits all Dana Model 60, Super 60, 61, and Closed Knuckle Model 70 axles from 1967-current. Also see TS4656 and TS4867 Inner Axle Seal Installer Tool Sets
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4862 Dana 60 Inner Axle Seal Remover Set Is used to drive the QU40059 inner axle seals out of the axle housing bores on all 1975-1993 Dodge W250 and W-350 4x4 Dana 60 or Dana 61 front axles. Set includes QT1145 Driver Handle, QT1151 Extension Rod, and QT1214 Seal Remover
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT2005 Dana 60 Inner Pinion Bearing Installer Is used to quickly and easily seat your QU50407 Inner Pinion Bearing on the pinion
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1805 Dana 60 Inner Pinion Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50406 Inner Pinion Bearing Cup a simple and fast procedure
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1812 Dana 60 Outer Pinion Bearing Cup Installer Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50400 Outer Pinion Bearing Cup a simple and fast procedure
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1088 Dana 60 Differential Step Plate Fits either side of the differential and are used to support the differential when installing your differential bearings or it acts as a push plate when you use a puller to remove the old bearings
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1158 Dana 60 Differential Bearing Installer Makes a hard job easy. The raised inside ridge matches against inner differential bearing race allowing you to easily press or drive on QU50398 differential bearing until the bearing is fully seated against the differential adjusting shims
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1098 Dana 60 Differential Master Bearings Slip on your differential in place of the taper bearings and cups. Used along with a dial indicator to determine the correct differential shim thickness
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1025 Dana 60 6 Prong Spindle Nut Socket for 6 Slot Round Nuts Used on 1978-1979 and early 1985 Ford F-350 Dana 60 Front axles with QU40036 Spindle Nuts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1110 Dana 60 4 Prong Spindle Nut Socket for 4 Slot Round Nuts Used on 1985-1991 Ford F-350 Dana 60 Front axles with QU40163 and QU40166 Spindle Nuts
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1033 Case Spreader Is used to relieve the differential bearing preload making it easy to safely remove and install your front differential without damaging expensive critical parts
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1023 Triple Thread Universal Spindle Puller Use with any 5/8" fine thread slide hammer to quickly and easily remove those rusted in QU40169 or QU40420 front wheel bearing spindles on your 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials on 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle. Also works on most GM 10 Bolt, Dana 50IFS, Dana 44, Dana 30, Dana 27, and Dana 25 front axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1024 Triple Thread Ford Spindle Puller Use with any 5/8" fine thread slide hammer to quickly and easily remove those rusted in QU40169 or QU40420 front wheel bearing spindles on your 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials on 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle. Also works on most Dana 44, Dana 35 IFS, and Ford Dana 28IFS front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1200 Tie Rod Separator Allows you to remove the separate tie rod and drag link ends without wrecking the seals or screwing up your steering linkage ends
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT9018 5 Pound Dead Blow Hammer Is just about the first tool you will reach for to complete a multitude of jobs on your Dodge Ram. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT9302 5 Pound Slide Hammer A first-class tool for pulling just about anything you can get a matching 5/8" fine thread puller attachment for
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1801 Outer Wheel Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50411 Outer Wheel Bearing Cup a simple and fast procedure
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1804 Inner Wheel Bearing Cup Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50396 Inner Wheel Bearing Cup a simple and fast procedure
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1505 Front Wheel Seal Installer Is custom made to quickly and easily install your new wheel seals without damaging them
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals (Individual)

top_page
product note
Ford used only the best wheel bearings and seals money could buy to equip their Dana 60 front axles to minimize the chance for warranty problems. That is why they chose Timken® Wheel Bearings and Spicer Wheel Seals for heavy-duty Ford F-350 4x4s using the big Danas. We supply those exact original equipment replacement Timken® Wheel Bearings and Spicer Wheel Seals to keep your Ford on the job for years to come
photo
QU50411 Timken® Outer Wheel Bearing Cup For all 1985-1991 Ford F-350 4x4 Dana 60 front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50412 Timken® Outer Wheel Bearing For all 1985-1991 Ford F-350 4x4 Dana 60 front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50396 Timken® Inner Wheel Bearing Cup For all 1985-1991 Ford F-350 4x4 Dana 60 front drive axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50398 Timken® Inner Wheel Bearing For all 1985-1991 Ford F-350 4x4 Dana 60 front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40119 Inner Wheel Seal Is a genuine Dana-Spicer original equipment replacement part for all 1985-1991 Ford F-350 4x4 Dana 60 front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
product note
Ford used the same wheel bearing and seal numbers for the entire 1985 to 1991 production run of Dana 60 King Pin type front drive axles. However, spindle nut sets will vary by year. We offer Wheel Bearing Part/Tool Kits with or without bearing and seal installation tools. If you need a spindle nut socket, see QT1025 for 1985 trucks or QT1110 for 1985.5-1991 models
photo
TK4744 Torque King® 1985-1991 Front Wheel Bearing and Seal Kit without Tools Is a parts only (No Tools) complete front Wheel Bearing and Seal Kit for your heavy-duty Ford featuring Timken® Bearings and original equipment wheel seals for all 1985-1991 Ford F-350 4x4 Dana 60 front drive axles. Kit includes 2 each of Timken® Inner and Outer Wheel Bearings/Bearing Cups, plus two Wheel Seals.
Link to our large text TK4744 catalog page
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK4738 Torque King® 1985-1991 Front Wheel Bearing and Seal Kit with Install Tools For all 1985-1991 Ford F-350 4x4 Dana 60 front drive axles. Kit includes Inner Wheel Bearing Cup Installer, Outer Wheel Bearing Cup Installer, Wheel Seal Installer, Driver Handle, plus 2 each of Timken® Inner and Outer Wheel Bearings/Bearing Cups, plus two Wheel Seals.This Kit DOES NOT INCLUDE Spindle Nut Socket or Hub Small Parts for your Ford!!!
Link to our large text TK4738 catalog page
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK4893 Torque King® 1985-1991 Front Timken Wheel Bearing Only Kit For Ford Dana 60 front axles with serviceable wheel bearings
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!