Parts for Dana-Spicer Model 60 Front Axles in 1992-1997 Ford 4x4 Trucks

We stock a wide selection of parts and Tools for 1992 to 1997 Ford F-350 Dana 60 open knuckle front drive axles with Ball Joints. The open knuckle, monobeam, Dana-Spicer Model 60 using Ball Joints instead of King Pins was introduced by Ford for the 1992 model year F-350 1 ton 4x4. The new axle, which is rated for a 5,000-pound capacity was the first production Dana 60 front axle to use Ball Joints, but it still had serviceable wheel bearings and lockout hubs like the previous 1985-1991 King Pin axle. Ford used the axle through the end of the 1997 model year when the F-350 line was dropped and replaced by the 1999 F-350 Super Duty which initially only had a Dana 50 front Axle.

Axle Identification

top_page
photo

1992-1997 Dana 60 Front Axles in Ford F-350 4x4 Trucks will typically have the Ford Build Code on a mylar decal affixed to the right axle tube. Also, the Dana Bill of Material Number (BOM) and Ford Build Code are stamped on a Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows) when the vehicle was shipped from the factory but, unfortunately, these tags are often missing on trucks that had prior differential service. The Dana BOM number is also stamped on the front side of the right axle tube. The BOM number is a 6 digit number beginning with a 6 plus a dash number (ex: 610604-2). They can be used to determine not only the axle model, but also what components the axle was originally built with. We often ask for this number to insure we provide you with the exact parts you need for your truck.

Each different BOM number signifies an engineering part change which may be minor or major and may involve one or more parts. The dash number indicates the axle ratio and, for some years, the front wheel hub style (for single or dual rear wheel models).

photo

1997 Ford F-350 Dana 60 front axles have a unique to Ford, reverse spiral ring and pinion set available in either 3.54 or 4.10 gear ratios. The reverse spiral gear sets are not interchangeable with standard gear sets.
Cover: 10 Bolt, 12" high
Ring Gear: 9-7/8", 12 Bolt

Suspension: Leaf spring

Axle Shafts: Outer Axle Shafts are 1-5/16" 30 spline and the 1-3/8" axle u-joint cups are retained by c-clips that seat against the inside of the axle shaft yoke ears.

Knuckle Mounting: Ball Joints

Wheel Hub: 1992-1997 Ford Model 60 axles have an internally splined hub in which a splined lockout hub assembly fits into. The wheel hub will vary by year and if vehicle has single or dual rear wheels.

1992 Bill of Material Numbers 610371

1993 Bill of Material Numbers 610432

1994 Bill of Material Numbers 610445

1995 Bill of Material Numbers 610460

1996-1997 Bill of Material Numbers 610610, 610741

1998 Bill of Material Numbers 1997 was the last Model year in U.S.A. for this body style F-350, however production continued until the 1999 F-350 Super Duty was released in early 1998. A 1997 model year F-350 built in 1998 should have BOM number 610741.

Axle Shafts

top_page
product note

All our axle shafts are brand new, genuine original equipment replacement parts for maximum strength.

photo

QU40371 1992-1997 30 Spline Ford Dana 60 Outer Axle Shaft For 1992 to 1997 Ford F-350 4x4 trucks with either single rear wheel or dual rear wheel trucks all of which have Dana 60 Front Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40526 1992-1997 35 Spline Ford Dana 60 Right Inner Axle Shaft For 1992 to 1997 Ford F-350 4x4 with either single rear wheel and dual rear wheels all of which have Dana 60 Front Axles.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40487 1992-1997 35 Spline Ford Dana 60 Left Inner Axle Shaft For 1992 to 1997 Ford F-350 4x4 single rear wheel and dual rear wheel trucks all of which have Dana 60 Front Axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Seals and Seal Kits for Inner Axle Shafts

top_page
product note

There is an Inner Axle Shaft Oil Seal located on either side of the Differential in 1992-1997 Ford Dana 60 Front Axles. If you are leaking oil out the end of your axle tubes, these are the seals that need to be replaced. At first, 1992 Axles used a conventional one piece seal carried over from 1991. This was replaced by an oil bath type Seal in which the inner portion of the seal rotates within the outer shell. The two seal designs were dimensionally interchangeable, however production of the Oil Bath Type was discontinued and Ford now catalogs the earlier QU40059 Seal as the correct replacement Seal for all 1992-1997 trucks. QU40243 Outboard Axle Shaft to Housing Seal is a Dust Seal that seals against the end of the axle tube. Axle disassembly including differential removal is required to replace the Inner Oil Seals.

photo

QU40059 Dana 60 Original Equipment Replacement Inner Axle Shaft Seal One of these Seals are installed in each axle tube, right next to the differential to keep gear lube from leaking out the ends of the axle housing on all 1992-1997 Ford F-350 1 ton 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4656 Adjustable Depth Type Inner Axle Shaft Seal Tool and Seal Kit For 1992-1997 Ford F-350 1 ton 4x4 trucks. Kit includes Installation Tools and two Seals. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TS4656 Adjustable Depth Type Inner Axle Shaft Seal Tool Set 1985-1991 Ford F-350 1 ton 4x4 trucks. Includes Installation Tools only, Purchase QU40059 Axle Seals separately. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40459 Ford F-350 Dana 60 Outboard Axle Shaft to Axle Housing Seal Installs on inner shaft next to the yoke on those inner axle shafts with a step machined next to the yoke for this seal. It's function is to keep dust and debris from entering the axle housing tubes. This is only a Dust Seal. If you see oil leaking past this seal, you need QU40059 Inner Axle Seal.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4983 Universal Dana 60 Oil Bath Inner Axle Seal and Tool Kit with Ford design universal fit Dana 60 oil bath type inner axle seals and adjustable depth installer tool set is specific to 2011-up Ford Super Duty, but these excellent seals will also fit 1999-2010 Ford Super Duty 4x4's. QK4983 is also the perfect upgrade package for older Dana 60 equipped vehicles including 1992-1997 F350 Ford trucks with Dana 60 Beam front axles. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note

We offer three different Universal Joints for your hard working Ford 4x4 Truck. All are plenty strong for the job, but different manufacturing techniques and seal types will have a major influence on the ultimate life of the joint. Our most popular choice is our TK40715 cold-forged, non-greaseable, original equipment replacement U-Joint. The wear-resistant cold-forged cross and superior sealing make it the best choice for both low maintenance and long life. Greaseable TK40724 U-Joints are a greaseable version of our TK40715 joints, giving you the durability advantages of cold-forging and better seals with the option to re-lube the joint at any time for unmatched longevity. QU30332's are hot-forged and equipped with simple rubber seals. With good maintenance and quality lubricant like our QU90018 Pyroplex® Plus Grease, these joints will last and last. See our individual product pages for more info.

photo

QU30332 Greaseable Axle U-Joint for Ford F-350 Dana-Spicer Model 60 Front Axle Value priced with Hot-Forged cross and flexible rubber seals. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40724 Torque King® Greaseable U-Joint Premium Cold-Forged cross and superior pressure-type seals, plus it is greaseable for unmatched life and durability! More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40715 Torque King® Premium Non-Greaseable U-Joint Original equipment type with Premium Cold-Forged cross and superior pressure-type seals. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK42117 Greaseable and Rebuildable CTM 1480WJ Series Performance Axle U-Joint for Ford F350 Dana 60 Beam Type Front Axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ball Joints

top_page
product note

For the F-350 Dana 60 Front Axle, Ford switched from King Pins to Ball Joints starting with the 1992 Model Year. Ball Joints are a wear item that will require replacement sooner or later. Here in Montana, the factory Ball Joints had an average life of somewhere between 7-10 years in ranch and contractor vehicles. Not bad, but nowhere near the life expectancy of the King Pin parts the earlier trucks used

photo

QK4592 Greaseable Ball Joint Kit Our Greaseable Ball Joints for your Ford F350 with Dana 60 Front Axle 4x4 truck are manufactured by Dana-Spicer. Order 1 Kit per axle.
More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QA50095 Premium Greaseable Upper Ball Joint is a Premium Quality made replacement Greaseable Upper Ball Joint with hardware for many Ford Dana 60 front axles.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50099 Greaseable Lower Ball Joint For Ford Dana 60 F350 1992-1997
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4591 Dana 60 Original Equipment Non-Greaseable Ball Joint Kit for your 1992-1997 Ford F350 4x4 truck are genuine original equipment replacement parts manufactured by Dana-Spicer. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40174 Dana 60 Original Equipment Non-Greaseable Ball Joint Set for 1992-1997 Ford F-350 4x4 Trucks Includes genuine Dana-Spicer original equipment replacement Upper and Lower Ball Joints with hardware. A quality Ball Joint Set that typically lasts for years under most conditions. Includes 1 upper and 1 lower ball joint with ball joint hardware. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

NEW from TORQUE KING®! Dynatrac Heavy-Duty Rebuildable 4X4 Greaseable BallJoints™

top_page
product note

The Torque King® lineup now includes Dynatrac Heavy-Duty BallJoints™ for Dana 60 front axles are the strongest, most durable and highest quality Ball Joints available anywhere, featuring heat-treated high-strength billet bodies with chromoly stems. Manufactured for us in USA by Dynatrac, the heat-treated, precision-ground stainless steel ball meets military specifications, a unique seal prevents contamination, plus the ball joints have greaseable fittings and Teflon-coated wear points to provide a long, durable life. Better yet, Torque King® Dynatrac Ball Joints are rebuildable -- they can be rebuilt on the vehicle with common hand tools! Installation procedures are the same as factory Ball Joints.

Make your Ford F-350 truck last! Order your Set now!

photo

TK42057 Dynatrac Heavy-Duty Rebuildable BallJoints™ for Dana 60 Solid Beam Type Front Drive Axles includes 4 American Made Rebuildable Ball Joints with ball joint hardware and installation instructions. TK42057 fits all 1992-1997 Ford F-350 4x4s.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
product note

Our stock of Ford F-350 front brake parts is limited. For the most part, the front brakes generally gave pretty good service that was comparable to the contemporary Dodge and GM 4x4's with one exception. We saw a lot higher percentage of Fords with warped or cracked brake rotors compared to the competition. Whether this was due to the somewhat thinner Ford brake rotor thickness or our Ford customers were harder on their brakes, I can't say, but an F-350 that was used to frequently tow a trailer always seemed to need rotors.

photo

QU20065 Disc Brake Caliper Pin For Bronco, F150, F250, F350 mid 1980's to mid 1990's. Genuine OEM Ford part. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20284 1992-1994 Left Front Brake Splash Shield for 1992-1994 Ford F350 Dana 60 Monobeam front axles. More Info

photo

QU20285 1992-1994 Right Front Brake Splash Shield for 1992-1994 Ford F350 Dana 60 Monobeam front axles. More Info

photo

QU20320 1995-1997 Left Front Brake Splash Shield For 1995-1997 Ford F350 with Dana 60 Monobeam front axles. More Info
Also available while supplies last: QU20320U Good Used 1980-1994 Left Front Brake Splash Shield

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20321 1995-1997 Right Front Brake Splash Shield For 1995-1997 Ford F350 with Dana 60 Monobeam front axles. More Info
Also available while supplies last: QU20321U Good Used 1980-1994 Left Front Brake Splash Shield

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings (Individual)

top_page
product note

If you only need a bearing or two for your 1992-1997 Ford F-350 Dana 60 diff, we stock the best: Timken®. For the amount of work it takes to change most axle bearings, the extra cost for a Timken® diff or pinion bearing is a small price to pay for better steel, more uniform surface finish, and accurate, precision ground races

photo

QU50397 Differential Bearing Cup For all 1992-1997 Ford Dana-Spicer Model 60 Front Axles. Use 2 per axle

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50398 Differential Bearing For all 1992-1997 Ford Dana-Spicer Model 60 Front Axles. Use 2 per axle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50400 Outer Pinion Bearing Cup For all 11992-1997 Ford Dana-Spicer Model 60 Front Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50401 Outer Pinion Bearing For all 1992-1997 Ford Dana-Spicer Model 60 Front Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50406 Inner Pinion Bearing Cup For all 1992-1997 Ford Dana-Spicer Model 60 Front Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50407 Inner Pinion Bearing For all 1992-1997 Ford Dana-Spicer Model 60 Front Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing and Seal Kits

top_page
product note
Torque King® Premium Diff Bearing and Seal Kits are the #1 choice for those who depend upon their truck to keep working day in and day out no matter how tough the conditions. Our Kits combine the superb quality of Timken bearings with the precise fit and reliability of 100% genuine Dana-Spicer small parts. No aftermarket, off brand or Chinese knockoff parts in these Kits!
photo
TK4864 Torque King® Premium Quality Front Differential Bearing and Seal Kit For your 1992-1996 Ford F-350 heavy-duty 4x4 truck features 100% Timken® Bearings and genuine Dana-Spicer Small Parts.

Also available: QU50491 Timken Bearing Kit with aftermarket small parts
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40184 Timken® Differential Bearing Cup and Bearing Set Includes two each QU50397 Differential Bearing Cup and QU50398 Differential Bearing
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
photo
QU40254 Model 60 Bare Differential Case Kit Includes bare case for 4.10 and numerically lower axle ratios, QU40519 Lock Pin, QU40206 Differential Shim Kit, and 12 QU40086 Ring Gear Bolts.

Please refer to QU40254 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20271U Good Used Differential Case Dana Model 60 is a genuine Dana-Spicer part. QU20271U fits many Dana-Spicer Model 60 front or rear axles with open differentials and 4.30 or numerically lower gear ratios (ex: 3.54). Also fits some Model 61 axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40041 Differential Side Gear Thrust Washer Fits between the large differential side gear and the differential case. Use 2 per axle.

Please refer to QU40041 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40518 Differential Pinion Mate Thrust Washer Fits between the small differential pinion mate gear and the differential case. Use 2 per axle.

Please refer to QU40518 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40519 Lock Pin for Differential Cross Shaft Is used to lock QU40520 Differential Cross Shaft to the Differential Case.

Please refer to QU40519 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40520 Differential Cross Shaft Acts as the axle for the two Pinion Mate Gears.

Please refer to QU40520 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40206 Differential Shim Kit A choice of selective fit shims used to set ring gear backlash and differential bearing preload.

Please refer to QU40206 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40343 Differential Cap Bolt Two of these Grade 8 bolts are used for each differential bearing cap
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Makers

top_page
product note
In the mid 1970's Dana made a differential cover design change to heavy gauge covers with flat mating flanges. Unlike the previous, thin gauge covers with embossed flanges which were made for use with a cut gasket, the new design, thick gauge covers are designed for sealing with RTV. If you desire, you can still use a gasket with the new type cover by combining the gasket with thin films of RTV. We stock both Ultra Gray RTV Sealant and genuine Dana Gaskets
photo
QU40367 Rear Differential Cover Gasket Dana has replaced the Dana 60 Gasket with a Dana 70 Gasket. These genuine Dana-Spicer Model 70 gaskets will also work on your Dana 60 front axles if you wish to use a Gasket in lieu of RTV sealant. Made in U.S.A
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Dodge Ram
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hubs and Lockout Hub Parts

top_page
product note

1992 Ford F-350 4x4s could be ordered with either automatic or manual hub lucks. For each version there are three different types of hubs used depending upon the year. For automatic hubs, only parts for the 1996-1997 version with a 3 bolt cover are still readily available. Parts for middle production (roughly 1993.5-1995) manual hubs are gone. The early manual hub was a standard Warn model, so parts are available for it. Incidently, since the early hub is still sold by Warn to the aftermarket, you may find it on any 1992-1997 F-350 either as the original hub or as a replacement for factory hubs. The 1995-1997 manual hub with a three bolt cap is still available from Ford as an assembly or sub-assemblies

photo

TKA4923 New 1995-1997 F350 Front Hub Is a new front wheel hub with Timken bearing cups for Dana 60 front axles in 1995-1997 Ford F350 4x4 Trucks

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TKA20332/QU20332U Wheel Hubs 1992-1994 F350 Chose from new and good used Ford splined Front Hubs for 1992-1994 Ford F-350 4x4 trucks with Dana 60 5000 pound front axles

More Info

photo

QU20264U 1995-1997 F350 8 Bolt 4x4 Front Wheel Hub Is a good used splined Front Hub for 1995-1997 Ford F-350 Single Rear Wheel 4x4s with Dana 60 Monobeam 5000 pound front axles

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20355 9/16" Front Wheel Stud for 1992-1997 F350 Is a hardened, fine thread replacement wheel stud for all 1992-1997 Ford F350 4x4 trucks.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56025 Warn Premium Hub Set for Dana 60 Front Axles With internally splined front wheel hubs. A sharp looking and reliable hub. QU56025 Fits Ford F-350 Dana 60 1992-1997

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56011 Warn® Dana Dana 60 Internal Spline Mount Hub Locks For 1992 to 1997 Ford F350 Dana 60 front axle. Kit includes two hubs with mounting hardware. QU56011 is the current production version of the Warn's original equipment 1980-1994 Ford Hub-Lock.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56022U Used Manual Lockout Hubs for 1995-1997 Ford Dana 60 4x4 front axles. These good used Manual Lockout Hubs have a 3 bolt cap. Sold as a pair. While supply lasts. Also available QU56022.5U for 1 side only, while supply lasts.
More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42116 30 Spline Drive Gear Kit for 1980-1982 Ford Dana 50IFS Front Axles with internal splined wheel hubs.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56013 Warn® Dial Assembly For Original Equipment Spline Mount Hubs used in Ford Dana 60 Front Axles
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56012 Original Equipment Warn® Hub Screw For Warn® Spline Mount Hubs in Ford Dana 60 Front Axles

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40113 Torx® Upgrade Screw For Warn® Spline Mount Hubs in Ford Dana 60 Front Axles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40155 Axle Shaft Snap Ring Fits in the groove machined at the end of the outer axle shaft splines in Ford Dana 60 Front Axles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40150 Lockout Hub to Wheel Hub Snap Ring for Warn® Spline Mount Hubs used in Ford Dana 60 Front Axles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50116 Cap QUAD-Ring square cross section sealing ring For Factory Warn® Spline Mount Hubs in Ford Dana 60 Front Axles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56017 Warn® Spiral Retaining Ring For Current Production Spline Mount Replacement Hubs

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50240 Dial O-Ring For Warn® Spline Mount Hub Dials in Ford Dana 60 Front Axles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU56016 Cap O-Ring For 1993.5-1997 factory manual hubs and Warn® Current Production Spline Mount Replacement Hubs

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20087 Hub Service Kit For Ford Dana 60 Front Axles with factory automatic hubs. QU20087 includes QU20200, QU20201, (3) QU20202, QU20203, QU20207, QU20208, QU20209, and QU20085. Order 1 QU20087 per side. 
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20085 30 Spline Three Piece Axle Thrust Washer Set Fits on the outer axle shaft splines between the spindle and axle shaft snap ring

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20200 Special Rounded Spindle Hex Nut Is a genuine original equipment replacement Spindle Nut for factory automatic hub equipped 1995-1997 Ford F-350 with Dana 60 front axles. Sold individually. Order two Nuts per vehicle.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20201 Auto Hub Spindle Nut Retaining Clip For Ford Dana-Spicer Model 60 Front Axles
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20202 Screw, Auto Hub Cap For Ford Dana-Spicer Model 60 Front Axles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20203 Auto Hub Decal For Ford Dana-Spicer Model 60 Front Axles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20207 Body Retaining Snap Ring For Auto Hub on Ford Dana-Spicer Model 60 Front Axles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20208 Axle Shaft Snap Ring for Auto Hub On Ford Dana-Spicer Model 60 Front Axles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20209 Sealing O-Ring for Auto Hub Cap On Ford Dana-Spicer Model 60 Front Axles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals and Technical Information

top_page
product note
Dan the Gear Man® Product Note: Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations
photo
TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts

top_page
product note
Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings
photo
S24200 Blue Threadlocker For spindle and ring gear bolts etc
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90018 Pyroplex® Protection ES Synthetic Grease Provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90016 SynPower ® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90015 Syncon High Performance Synthetic Arctic Grease Is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90017 707L Red Grease Is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. cartridge or 1 pound tub
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals and Pinion Yokes

top_page
product note
Ford used 2 different Pinion Yokes on 1992-1997 era F-350 4x4 Dana 60 Front Axles. The two yokes are identical except for the slinger (deflector) which was used for 1992-1996 but deleted in 1997. The original equipment pinion yokes use QU40841 U-bolts to secure the oversize 1.125" u-joint cups used on the Ford specific 1330F universal joints (See TK40723 and QU40776 ). The original QU20179 1330F Pinion Yokes are now out of production although we still have some available as of September 2011. A less expensive and more readily available alternative to the original yoke is to replace the 1330F u-joint with a straight 1330 U-joint (TK40721, (QU40774 ) and use QU40713 1330 series pinion yokes
photo
QU40097 1992-1996 Ford F-350 Dana 60 Front Axle Pinion Seal This genuine Dana-Spicer original equipment pinion seal fits all 1992-1996 Ford F-350 1 ton 4x4 trucks Model 60 open knuckle front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40348 Dana 60 1997 Pinion Seal For Model 60 front axles in 1997 Ford F-350 4x4 trucks. This seal is used in conjunction with QU40397 V-Seal and with yokes that do not have a steel deflector shield
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40397 1997 Pinion Wiper V-Seal Protects QU40348 Pinion Seals from road splash
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20179 1330F Front Dana 60 Pinion Yoke Is a genuine original equipment replacement pinion yoke for 1994-1996 Ford F-350 Dana 60 axles. Will also work on 1997 if QU40097 Seal is used or if the Slinger is removed
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40841 Driveshaft U-Bolt Kit for Ford F-350 Dana 60 Front Axle Fits all 1992-1997 Ford original equipment Front Dana 60 pinion yokes including QU20179.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40713 1330 Series 1985-1991 Dana 60 Pinion Yoke Is a lower cost option than QU20179 that takes standard 1330 series universal joints for 1985-1991 F-350 4x4s originally equipped with QU20179 1330F pinion yoke having a cone shaped shaped deflector
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40735 Universal Joint Strap and Bolt Kit for QU40713 1330 Pinion Yokes This genuine Spicer original equipment Kit is used to secure Spicer type universal joints with 1-1/16" diameter cups to Dana 60 axle pinion yokes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
product note

1992-1997 Ford F-350 front Dana 60 axles have reverse spiral pinion gears that are set above the axle center line. The reverse spiral gear sets are probably not quite as strong as the standard cut gearing, but the high pinion significantly reduces front driveshaft angles and the extra ground clearance helps keep the pinion yoke and front driveshaft u-joint out of harm's way. The standard cut and reverse spiral gear sets ARE NOT INTERCHANGEABLE!

photo
QU40620 3.54 Ratio Ford Dana 60 Ring and Pinion Set For 1992-1997 Dana 60 front axles in Ford F350 4x4 trucks. QU40620 3.54 ratio Ring and Pinion Kit is a genuine Dana reverse spiral gear set with pinion bearings, pinion seal, ring gear bolts, pinion nut, pinion washer, diff cover gasket, small parts, and shims
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20337U 4.10 Ratio Ring and Pinion For 1992-1997 Ford F350 Dana 60 front axle.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note
Dan the Gear Man® Product Note: As with most repair jobs, it is the little things that make the difference between a poor job and a repair that will last. We stock many of those small but vitally important small parts for your 1992-1997 Ford F-350 4x4 Dana-Spicer Model 60 front axle
photo
QU20085 30 Spline Three Piece Axle Thrust Washer Set Fits on the outer axle shaft splines between the spindle and axle shaft snap ring
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40022 Pinion Nut Is a single use nut that should be replaced anytime it has been removed
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40023 Hardened Pinion Flat Washer Fits between the pinion yoke and pinion nut
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40086 Ring Gear Bolt 12 of these nonreusable bolts are used to join the ring gear to the differential case
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40099 Outer Pinion Slinger Fits between the pinion yoke and outer pinion bearing
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindles, Spindle Hardware, and Spindle Nuts

top_page
product note

The Spindles for 1992-1997 Ford F-350 Dana 60 4x4 Front Axles are the same but different Spindle Nuts are used depending upon the lock out hubs option. Manual Hub equipped trucks use a three piece Round Spindle Nut and Washer set. Trucks with Auto Hubs use a single Rounded Hex Nut. The Spindle Nuts are NOT interchangeable for use with either hub style so if you are converting your Hub-Locks from auto to manual or vise-versa, you will also have to change the Spindle Nuts to match the new hubs.

photo

QU20200 Spindle Nut for Auto Hubs On 1992-1997 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle. Use with QU20201 Retaining Clip.

Link to our QU20200 large text catalog page for more details and tech notes.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20201 Auto Hub Spindle Nut Retaining Clip For Ford Dana-Spicer Model 60 Front Axles.

Link to our QU20201 large text catalog page for more details and tech notes.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40163 Ford F-350 Round Outer Spindle Nut for Manual Hub Axles On 1992-1997 Ford F-350 4x4 has 4 slots for QT1018 Spindle Nut Wrench

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40164 Ford F-350 Spindle Lock Washer for Manual Hub Axles On 1992-1997 Ford F-350 4x4 with round spindle nuts is reusable

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40166 Ford F-350 Round Inner Spindle Nut with Pin for Manual Hub Axles On 1992-1997 Ford F-350 4x4 has 4 slots for QT1018 Spindle Nut Wrench. Includes round pin that engages one of the holes in QU40164 Spindle Lock Washer

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4729 Ford F-350 Round Spindle Nut Kit For Manual Hub equipped 1992-1997 Ford F-350 4x4 includes one each QU40163, QU40164, and QU40166

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU95036 Heat-treated, All Metal, Spindle to the Steering Knuckle Lock Nut Six of these USA Made, 150, 000 psi rated Locknuts fit on QU40540 Spindle to Knuckle Bolt to secure each of your front Spindles to the Steering Knuckles

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40539 Spindle-to-Knuckle Bolt Five of these press-in special bolts fit each steering knuckle on 1992-1997 Ford F-350 Dana 60 Front Axles. They are used along with QU95036 Locknut to retain your spindles and caliper anchor plates

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40420 1992-1997 Ford F-350 Dana 60 Front Spindle Kit For all 1992-1997 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Y440420 Replacement Dana 60 Front Spindle Kit for 1992-1997 Ford F350 is a low cost, yet high quality replacement part. Imported.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Bearings and Seals

top_page
product note
The dead, hollow spindle design of the 1992-1997 era Ford F-350 Dana 60 series axles uses QU40149 needle bearing to support the outer axle shaft. The two part Spindle Seal and Thrust Washer design was new for 1992, replacing the earlier four piece set-up used from 1978-1991. Personally, I prefer the older Seal design which can be retrofitted to 1992-1997 trucks if you order (2) QU40064 and (1) QK4740
photo
QU40496 1992-1997 Ford F-350 Dana 60 Unitized Inner Spindle Seal and Thrust Washer
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40243 1992-1997 Ford F-350 Dana 60 Unitized Outer Spindle to Axle Shaft Seal and Slinger
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40372 1992-1997 Unitized Spindle Seal, Bearing and Thrust Washer Kit
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40149 1992-1997 Ford F-350 Dana 60 Spindle Bearing Is a genuine Dana Spicer original equipment part that is a press fit in the back of the spindle. This bearing is the primary support for your outer axle shaft
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Knuckles

top_page
photo
QU20319U Used Left Steering Knuckle For 1995-1997 Ford F350 4x4 Trucks with Dana 60 Front Axles, Good Used
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 60 front axle in your 1992-1997 Ford F-350.

photo
TS4511 Ball Joint Press Set for 1992-1997 Ford F-350 4x4 Trucks Includes a heavy-duty, long throat C-Frame Press and six adapters custom made for removing and installing the pressed fit Ball Joints in your steering knuckles quickly, easily, and safely
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT5500 Wheel Bearing Packer Takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your big Ford!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4656 Dana 60 Adjustable Depth Type Inner Axle Shaft Seal Tool Set For 1992-1997 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle. Includes QT1042 Adjustable Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate. Purchase QU40059 Axle Seals separately
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1133 Dana 60 Inner Axle Seal Press Screw Assembly For installing Inner Axle Seals in 1992-1997 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle. Use with the QT1042, QT1156, QT1126 Seal Installers and QT1130 Thrust Plate Thrust Plate
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1042 Dana 60 Adjustable Depth Inner Axle Seal Installer For 1992-1997 F-350. Also see TS4656 Inner Axle Seal Installer Tool Set
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1130 Dana 60 Thrust Plate Fits all Dana Model 60, Super 60, 61, and Closed Knuckle Model 70 axles from 1967-current. Also see TS4656 and TS4867 Inner Axle Seal Installer Tool Sets.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4862 Dana 60 Inner Axle Seal Remover Set Is used to drive the QU40059 inner axle seals out of the axle housing bores on all 1975-1993 Dodge W250 and W-350 4x4 Dana 60 or Dana 61 front axles. Set includes QT1145 Driver Handle, QT1151 Extension Rod, and QT1214 Seal Remover
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT2005 Dana 60 Inner Pinion Bearing Installer Is used to quickly and easily seat your QU50407 Inner Pinion Bearing on the pinion
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1805 Dana 60 Inner Pinion Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50406 Inner Pinion Bearing Cup a simple and fast procedure
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1812 Dana 60 Outer Pinion Bearing Cup Installer Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50400 Outer Pinion Bearing Cup a simple and fast procedure
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1088 Dana 60 Differential Step Plate Fits either side of the differential and are used to support the differential when installing your differential bearings or it acts as a push plate when you use a puller to remove the old bearings
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1158 Dana 60 Differential Bearing Installer Makes a hard job easy. The raised inside ridge matches against inner differential bearing race allowing you to easily press or drive on QU50398 differential bearing until the bearing is fully seated against the differential adjusting shims
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1098 Dana 60 Differential Master Bearings Slip on your differential in place of the taper bearings and cups. Used along with a dial indicator to determine the correct differential shim thickness
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1058 Rounded Hex Spindle Nut Socket For 1994-1997 F350 4x4 trucks with factory automatic locking hubs
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1110 Dana 60 4 Prong Spindle Nut Socket for 4 Slot Round Nuts Used on 1992-1997 Ford F-350 Dana 60 Front axles with manual hub locks
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1032 Case Spreader Is used to relieve the differential bearing preload making it easy to safely remove and install your front differential without damaging expensive critical parts.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1023 Triple Thread Universal Spindle Puller Use with any 5/8" fine thread slide hammer to quickly and easily remove those rusted in QU40169 or QU40420 front wheel bearing spindles on your 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials on 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle. Also works on most GM 10 Bolt, Dana 50IFS, Dana 44, Dana 30, Dana 27, and Dana 25 front axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1024 Triple Thread Ford Spindle Puller Use with any 5/8" fine thread slide hammer to quickly and easily remove those rusted in QU40169 or QU40420 front wheel bearing spindles on your 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials on 1985-1991 Ford F-350 1 ton 4x4 trucks with the Dana 60 front drive axle. Also works on most Dana 44, Dana 35 IFS, and Ford Dana 28IFS front axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1200 Tie Rod Separator Allows you to remove the separate tie rod and drag link ends without wrecking the seals or screwing up your steering linkage ends
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT9018 5 Pound Dead Blow Hammer Is just about the first tool you will reach for to complete a multitude of jobs on your Dodge Ram. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT9302 5 Pound Slide Hammer A first-class tool for pulling just about anything you can get a matching 5/8" fine thread puller attachment for
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1801 Outer Wheel Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50411 Outer Wheel Bearing Cup a simple and fast procedure
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1804 Inner Wheel Bearing Cup Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50396 Inner Wheel Bearing Cup a simple and fast procedure
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1505 Front Wheel Seal Installer Is custom made to quickly and easily install your new wheel seals without damaging them
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TS4983 Inner Axle Seal Installer Tool Set for installing Ford design QU20463 oil bath type inner axle seals in 1992 to 1997 Ford Dana 60 front axles. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals (Individual)

top_page
product note
Ford used only the best wheel bearings and seals money could buy to equip their Dana 60 front axles to minimize the chance for warranty problems. That is why they chose Timken® Wheel Bearings and Spicer Wheel Seals for heavy-duty Ford F-350 4x4s using the big Danas. We supply those exact original equipment replacement Timken® Wheel Bearings and Spicer Wheel Seals to keep your Ford on the job for years to come
photo
QU50411 Timken® Outer Wheel Bearing Cup For all 1992-1997 Ford F-350 4x4 Dana 60 front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50412 Timken® Outer Wheel Bearing For all 1992-1997 Ford F-350 4x4 Dana 60 front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50396 Timken® Inner Wheel Bearing Cup For all 1992-1997 Ford F-350 4x4 Dana 60 front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50398 Timken® Inner Wheel Bearing For all 1992-1997 Ford F-350 4x4 Dana 60 front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40119 Inner Wheel Seal Is a genuine Dana-Spicer original equipment replacement part for all 1992-1997 Ford F-350 4x4 Dana 60 front drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
product note
Ford used the same wheel bearing and seal numbers for the entire 1992 to 1997 production run of Dana 60 Ball Joint type front drive axles. However, spindle nut sets will vary by year and Lock Out Hub option. We offer Wheel Bearing Part/Tool Kits with or without bearing and seal installation tools. If you need a spindle nut socket, see QT1110 for 1992-1997 models with manual hubs or QT1058 Rounded Hex Spindle Nut Socket for 1994-1997 trucks with factory auto locking hubs
photo
TK4744 Torque King® 1992-1997 Front Wheel Bearing and Seal Kit without Tools Is a parts only (No Tools) complete front Wheel Bearing and Seal Kit for your heavy-duty Ford featuring Timken® Bearings and original equipment wheel seals for all 1992-1997 Ford F-350 4x4 Dana 60 front drive axles. Kit includes 2 each of Timken® Inner and Outer Wheel Bearings/Bearing Cups, plus two Wheel Seals
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK4738 Torque King® 1992-1997 Front Wheel Bearing and Seal Kit with Install Tools For all 1992-1997 Ford F-350 4x4 Dana 60 front drive axles. Kit includes Inner Wheel Bearing Cup Installer, Outer Wheel Bearing Cup Installer, Wheel Seal Installer, Driver Handle, plus 2 each of Timken® Inner and Outer Wheel Bearings/Bearing Cups, plus two Wheel Seals. This Kit DOES NOT INCLUDE Spindle Nut Socket or Hub Small Parts for your Ford!!!
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!