Parts for Dana Super 60 Coil Spring Front Axles in 2005-2010 Ford F-250 and Standard Width F-350 4x4 Trucks

We stock a wide selection of parts and special tools for the 2005-2016 Ford F-250 and Standard Width F-350 Super Duty® 4x4 trucks. The 4x4 Ford Super Duty® line went through a major front axle redesign for the 2005 model year. The most obvious difference is the the 2005 to 2016 trucks have coil spring front suspension instead of leaf springs which were a mainstay feature of all previous F-250 4x4s all the way back to 1959. Less apparent is the 2005-2016 axle is a Dana Super 60 compared to standard Dana 50 and Dana 60 axles for the 1999-2004 models. The Dana Super 60 does share some components with the old Dana 60, however, the majority of parts are not interchangeable between the two axle models. This page includes parts for all F250 and standard width front axle F350 4x4s. NOTE: If you have a "Fat Boy" "Extended Track" or "Tow Boss" F350 call or email us with your truck serial number before ordering parts as your front axle has a mix of F350 and F450 front axle parts.

Axle Assemblies and Axle Housings

top_page
product note

2005-2016 Ford F250 and most width F350 4x4s use the same length axle shafts for the 2005-2016 model years. The only exception is some F350 crew cab and ambulance package dual rear wheel vehicles with the "Fat Boy" extended front axle option. Even though all the F250 and regular F350 side specific axle shafts are interchangeable, what is confusing is the matching dust seals that go at the outboard end of the axle housing tubes may need to be changed to a different style when you buy a replacement axle shaft. You will find some trucks with a dust seal that presses on the inner axle shaft next to the yoke, some with a cartridge seal pressed into the end of the axle housing, and some that only use a loose-fitting plastic slinger on the inner axle shaft. Except for early production trucks that all used the seal pressed against the inner axle shaft yoke, there is no hard and fast rule about which seal was used for production. There have been multiple numbers listed for each axle shaft assembly, and they only differ in the dust seal type.

photo

QU20305 Super Duty Right Axle Shaft Assembly for 2005-2016 Ford F250, F350 trucks with Dana Super 60 Front Axle is a brand new, genuine Dana original equipment passenger side axle shaft assembly for all 2005-2016 Ford F250 and standard axle width F350 Super Duty 4x4s. QU20305 includes inner and outer shafts, greaseable cold-forged axle u-joint, QU20052 Axle to Knuckle Seal, and inner axle shaft dust slinger. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20582 Super Duty Left Axle Shaft Assembly for 2005-2016 Ford F250, F350 trucks with Dana Super 60 Front Axle is a brand new, genuine Dana original equipment drivers side axle shaft assembly for all 2005-2016 Ford F250 and standard axle width F350 Super Duty 4x4s. QU20582 includes inner and outer shafts, greaseable cold-forged axle u-joint, QU20052 Axle to Knuckle Seal, and inner axle shaft slinger. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20278U Good Used Dana Super 60 Front Monobeam Axle Housing with Differential Bearing Caps for 2005-2010 F250, F350. Shipped Truck Freight.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shafts, Individual Outer and Related Part

top_page
photo
QU40414 2005-2010 Ford F250, F350 Super Duty® Outer Axle Shaft Snap Ring Fits in a groove machined in the Outer Axle Shaft to hold the Shaft in position in the wheel hub
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20073 Axle Shaft Support Bearing Kit for 2005-up Ford Super Duty Replaces your original, worn Axle Shaft Support Bearing in the back of the wheel hub.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20042 Outer Axle Shaft for 2005-2010 Ford Super Duty® F250/F350 Original equipment replacement for a worn or broken outer axle shaft.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20461 Bare Front Axle Shaft for 2005-up Ford Super Duty F250 and F350 4x4 trucks. This is a genuine Dana part.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Seals and Seal Kits for Inner Axle Shafts

top_page
product note

Your Inner Axle Shaft Seals are located in the differential housing just outboard of the differential bearings. If you are leaking oil out the end of your axle tubes, these are the seals that need to be replaced. Effective with the 2011 model year, Ford replaced QU40244 1st Design Inner Axle Shaft Seal which features an integral oil slinger on the diff side plus a generous axle shaft guide on the outboard side with QU20463 Seal that has no slinger and only a small shaft guide. Functionally, the seals are completely interchangeable on 1999 to 2016 Ford Dana 50, Dana 60, and Dana Super 60 front axles, but they do require different installers.

photo

QU40244 First Design Super Duty® Inner Axle Shaft Oil Seals Are oil-bath type seals with an integral oil slinger on the inboard side and a generous axle shaft guide on the outboard side. QU40244 1st Design Seal is specific to 2005-2010, but it is functionally interchangeable with QU20463 2011-2016 Seal. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20463 2nd Design Ford Dana Super 60 Inner Axle Seal is a high-quality, original equipment oil bath type inner axle shaft oil seal that is specific to 2011-2016 Ford Dana Super 60 front axles in Super Duty F250, F350, F450, and F550 4x4 trucks. This seal can also be used to replace QU40244 in 1999-2010 Ford Dana 60 and Super 60 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4807 Fixed Depth Inner Axle Shaft Seal Kit for Ford 2005-2010 Super Duty® Dana Super 60 front drive axles. Quickly and easily press in new inner axle seals without damage to an exact, predetermined depth! Installation tool cups the seal so force is only applied on the outer shell
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4644 Adjustable Depth Inner Axle Shaft Seal Kit for Ford 2005-2010 Super Duty® Dana Super 60 Front Axles. Kit includes two Inner Axle Shaft Oil Seals and CNC Precision Machined Installation Tools to service the Inner Axle Oil Seals on 2005-2010 Ford Super Duty® Super 60 front drive axles. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QK4983 2011-Current Dana Super 60 Oil Bath Inner Axle Seal and Tool Kit with Ford design universal fit Dana 60 oil bath type inner axle seals and adjustable depth installer tool set is specific to 2011-up Ford Super Duty, but these excellent seals will also fit 1999-2010 Ford Super Duty 4x4's. QK4983 is also the perfect upgrade package for older Dana 60 equipped vehicles including 1975-1993 Dodge, 1977-1991 GM, and 1978-1979 F250, F350, and 1985-1997 F350 Ford trucks with Dana 60 Beam front axles.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20049 Outboard Axle Shaft Cartridge Type Dust Seal for 2005-2010 Ford Super Duty® Current Style Seal Design gets pressed in the end of the axle housing. It's function is to keep dust and debris from entering the axle housing tube.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40538 Outboard Axle Shaft to Axle Housing Seal for 2005-2010 Ford Super Duty® Early Style Design Seal presses on inner shaft next to the yoke. It's function is to keep dust and debris from entering the axle housing tubes.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Seals and Seal Kits for Outer Axle Shafts

top_page
product note

Seal replacement is required anytime the axle shaft is removed to prevent vacuum leaks and or water infiltration. Use the TS1530 (F250-F350) for damage free installation of the knuckle seal on the outer axle shaft and then use it to seat the axle shaft assembly in the knuckle to the proper depth

photo

QU20052 2005-up Ford Super Duty Outer Axle Shaft to Steering Knuckle Seal or Vacuum Seal Is a nearly 5-1/2" diameter, genuine original equipment Seal that presses on your outer axle shaft to seal the back of the steering knuckle. Install with TS1530 Seal Installer. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4680 2005-2016 Ford F-250, F-350 Super Duty Knuckle and Hub Seal Kit Includes 2 Knuckle Seals, 2 wheel hub to knuckle o-rings, 6 special hub screws, 2 hub gaskets, and 2 lockout hub o-rings. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4678 2005-2016 Ford F-250, F-350 Super Duty Knuckle and Hub Seal Kit with Installer includes our heavy-duty TS1530 Knuckle Seal Installer, 2 Knuckle Seals, 2 wheel hub to knuckle o-rings, 6 special hub screws, 2 hub gaskets, and 2 lockout hub o-rings. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note

We stock 3 Axle Universal Joint choices for your 2005 and up Ford Super Duty®F-250 or F-350. Choose QU30332 for value, TK40715 for long life and no maintenance, or TK40724 for the ultimate combination for strength and durability

photo
QU30332 Greaseable Axle U-Joint for Dodge Dana-Spicer Model 60 Front Axle Value priced with Hot-Forged cross and flexible rubber seals.

Please refer to QU30332 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK40724 Torque King® Greaseable U-Joint Premium Cold-Forged cross and superior pressure-type seals, plus it is greaseable for unmatched life and durability!

Please refer to TK40724 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK40715 Torque King® Premium Non-Greaseable U-Joint Original equipment type with Premium Cold-Forged cross and superior pressure-type seals.

Please refer to TK40715 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK42117 Greaseable and Rebuildable CTM 1480WJ Series Performance Axle U-Joint for Ford F250 and F350 Dana 60 Beam Type Front Axles.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ball Joints

top_page
product note

Two sizes of Ball Joints are used on 2005-2010 Ford Super Duty 4x4 trucks. F250 and F350 models have 6000 pound capacity axles using factory lubed Ball Joints that are similar in size to those used in previous generation Super Duty/F350 front axles. F450 and F550 vehicles use larger, higher capacity greaseable Ball Joints which up the axle rating to 7000 pounds.

photo
QU40579 Original Equipment Ball Joint Set For 2005-2010 Ford Super Duty F250 and F350 4x4 trucks with 6000 pound Dana Super 60 front axles and coil spring front suspension
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU80052 Greaseable Upper Ball Joint For 2005-2010 Ford F250, F350 Super Duty®.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

NEW from TORQUE KING®! Dynatrac Heavy-Duty Rebuildable 4X4 Greaseable BallJoints™

top_page
product note
The Torque King® lineup now includes Dynatrac Heavy-Duty BallJoints™ for Dana 60 front axles are the strongest, most durable and highest quality Ball Joints available anywhere, featuring heat-treated high-strength billet bodies with chromoly stems. Manufactured for us in USA by Dynatrac, the heat-treated, precision-ground stainless steel ball meets military specifications, a unique seal prevents contamination, plus the ball joints have greaseable fittings and Teflon-coated wear points to provide a long, durable life. Better yet, Torque King® Dynatrac Ball Joints are rebuildable -- they can be rebuilt on the vehicle with common hand tools! Installation procedures are the same as factory Ball Joints.

Make your Ford Super Duty truck last! Order your Set now!

photo
TK42057 Dynatrac Heavy-Duty Rebuildable BallJoints™ for Dana 60 Solid Beam Type Front Drive Axles includes 4 American Made Rebuildable Ball Joints with ball joint hardware and installation instructions. TK42057 fits all 2005-2015 Ford F250 and F350 4x4s.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings (Individual)

top_page
photo
QU50397 Differential Bearing Cup For all 2005 and up Ford Super Duty® F-250 and F-350 Model 60 Front Axles. Use 2 per axle.

Please refer to QU50397 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50398 Differential Bearing For all 12005 and up Ford Super Duty® F-250 and F-350 Model 60 Front Axles. Use 2 per axle.

Please refer to QU50398 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50400 Outer Pinion Bearing Cup For all 12005 and up Ford Super Duty® F-250 and F-350 Model 60 Front Axles.

Please refer to QU50400 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50401 Outer Pinion Bearing For all 2005 and up Ford Super Duty® F-250 and F-350 Model 60 Front Axles.

Please refer to QU50401 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50406 Inner Pinion Bearing Cup For all 2005 and up Ford Super Duty® F-250 and F-350 Model 60 Front Axles.

Please refer to QU50406 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50407 Inner Pinion Bearing For all 2005 and up Ford Super Duty® F-250 and F-350 Model 60 Front Axles.

Please refer to QU50407 page for more details and ordering information.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing and Seal Kits

top_page
photo
QU40184 Timken® Differential Bearing Cup and Bearing Set Includes two each QU50397 Differential Bearing Cup and QU50398 Differential Bearing.

Please refer to QU40184 page for more details and ordering information.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
photo
QU40206 Differential Shim Kit A choice of selective fit shims used to set ring gear backlash and differential bearing preload.

Please refer to QU40206 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40343 Differential Cap Bolt Two of these Grade 8 bolts are used for each differential bearing cap.

Please refer to QU40343 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Makers

top_page
product note
Dan the Gear Man® Product Note: Orange or Gray RTV sealant was used by Dana-Spicer to seal the differential cover. We stock Ultra Gray RTV Sealant which has high adhesion and excellent resistance to synthetic lubricants, or if you prefer a cut gasket, order QU40367
photo
QU40367 Differential Cover Gasket For Model 70 Axles These genuine Dana-Spicer gaskets will also work on Dana 60 axles. Dan the Gear Man® Tech Note: RTV sealant instead of Gaskets were used during the factory assembly of your axle. Made in U.S.A.

Please refer to QU40367 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Ford Super Duty®.

Please order your S82194 Ultra Gray RTV Sealant from our Shop Supplies Web Page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hubs and Hub Parts

top_page
product note

Our Free-Spin Kits are made in USA for us by Dynatrac for your popular Ford Super Duty 4x4 and are engineered for a lifetime of trouble-free operation. Torque King® Dynatrac Free-Spin Kits include heat-treated chromoly dead spindles, Timken® wheel bearings and seals, 35-spline 1.50-inch chromoly outer shafts, wheel hubs, Warn locking hubs, and all necessary tone rings, studs and hardware. Torque King® Dynatrac Free-Spin Kits replace problematic unit live spindle front hub assemblies that have closely spaced, non-adjustable, and non-serviceable wheel bearings with widely spaced, replaceable, and adjustable wheel bearings. By spacing the bearings farther apart, the wheel and tire assembly has less leverage on the bearings, reducing wear and increasing bearing life. Torque King® Dynatrac Free-Spin Kits have a dead spindle design which means the spindle is solidly bolted to the steering knuckle and it does not rotate with the axle shaft like Dodge Ram or around the axle shaft like a Ford. Having both locking hubs and dead spindle design means your front axle wear will be decreased and chances are your 4x4 will get measurably better fuel mileage. All Kits come stock with premium Warn 62672 35 spline lock out hubs. Dynatrac DynaLoc™ lock out hubs are available as a $300 option on any Kit.

You can order your Kit in advance and pickup it up at our new store located at 7095 Commercial Ave, Billings, Montana, just southeast of the I-90 Zoo Drive exit.

photo
QU56026 Warn 95060 Premium Black Hub Set for 2005-Up Ford Super Duty Replaces failed factory hubs at a fraction of Ford cost. QU56026 is a manual hub set that can replace both manual and auto locking hub locks on all 2005 and newer Ford Super Duty F250, F350 4x4 trucks
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU56027 Warn 95070 Premium Chrome Hub Set for 2005-Up Ford Super Duty Replaces failed factory hubs at a fraction of Ford cost. QU56027 is a sharp-looking manual hub set that can replace both manual and auto locking hub locks on all 2005 and newer Ford Super Duty F250, F350 4x4 trucks
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20046 Lockout Hub Gasket and O-Ring Kit Includes 1 adhesive gasket, 1 Hub Lock Body O-Ring, and 3 Hub Screws
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20045 2005-2010 Ford Super Duty® Wheel Hub to Steering Knuckle O-Ring Is a genuine original equipment O-Ring that fits in a groove in your wheel hub
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20181 Ford Super Duty® Hub-Lock to Wheel Hub O-Ring Is a genuine original equipment, special synthetic O-Ring that fits in a groove in your hub-lock assembly. Photo shows 2 O-Rings
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20073 Axle Shaft Support Bearing Kit for 2005-up Ford Super Duty Replaces your original, worn Axle Shaft Support Bearing in the back of the wheel hub
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40415 2005-2010 F250, F350 Hub to Knuckle Stud Is a genuine original equipment hardened, fine thread stud for 2005-2010 Ford Super Duty F250, F350 4x4 Front Axles.

Link to our QU40415 Catalog Product Page

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20081 Hub to Knuckle Flanged Nut Threads on QU40415 Stud to secure the wheel hub to the steering knuckle.

Link to our QU20081 Catalog Product Page

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU20596 Replacement Vacuum Hub Control Solenoid for 2005-2010 Ford Dana Super 60 Super Duty F250-F350 with electric shift transfer case.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TORQUE KING® DYNATRAC Free-Spin™ Front Hub Kits with Serviceable Wheel Bearings

top_page
product note

Our Free-Spin Kits are made in USA for us by Dynatrac for your popular Ford Super Duty 4x4 and are engineered for a lifetime of trouble-free operation. Torque King® Dynatrac Free-Spin Kits include heat-treated chromoly dead spindles, Timken® wheel bearings and seals, 35-spline 1.50-inch chromoly outer shafts, wheel hubs, Warn locking hubs, and all necessary tone rings, studs and hardware. Torque King® Dynatrac Free-Spin Kits replace problematic unit live spindle front hub assemblies that have closely spaced, non-adjustable, and non-serviceable wheel bearings with widely spaced, replaceable, and adjustable wheel bearings. By spacing the bearings farther apart, the wheel and tire assembly has less leverage on the bearings, reducing wear and increasing bearing life. Torque King® Dynatrac Free-Spin Kits have a dead spindle design which means the spindle is solidly bolted to the steering knuckle and it does not rotate with the axle shaft like Dodge Ram or around the axle shaft like a Ford. Having both locking hubs and dead spindle design means your front axle wear will be decreased and chances are your 4x4 will get measurably better fuel mileage. All Kits come stock with premium Warn 62672 35 spline lock out hubs. Dynatrac DynaLoc™ lock out hubs are available as a $300 option on any Kit.

You can order your Kit in advance and pickup it up at our new store located at 7095 Commercial Ave, Billings, Montana, just southeast of the I-90 Zoo Drive exit.

photo

TK42070 Dynatrac Front Free-Spin™ Hub Kit for 2005-2015 Ford F250, F350 Includes Heat-treated chromoly spindles with spindle bearing, spindle seal, Timken wheel bearings and wheel seals, 35-spline 1.50-inch chromoly outer shafts, 8 bolt Wheel hubs, double spindle nut kit, Warn® premium locking hubs, instructions, and All necessary studs and hardware. If you have a dual rear wheel F350, you will also need optional new hub extensions to provide clearance for the locking hubs.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK42071 Dynatrac Front Free-Spin™ Hub Kit for 2005-2015 Ford F250, F350 Includes Heat-treated chromoly spindles with spindle bearing, spindle seal, Timken wheel bearings and wheel seals, 35-spline 1.50-inch chromoly outer shafts, 8 bolt Wheel hubs, double spindle nut kit, Dynaloc® premium locking hubs, instructions, and All necessary studs and hardware. If you have a dual rear wheel F350, you will also need optional new hub extensions to provide clearance for the locking hubs.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK4969 Torque King® Master Free-Spin Kit with Warn® Hublocks includes TK42070 Dynatrac Free-Spin Wheel Hub/Outer Axle Shaft Kit, Warn® Hubs, Torque King® greaseable axle u-joints, and spindle nut socket.

More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK4973 Torque King® Master Free-Spin Kit with Dynaloc Hublocks includes TK42071 Dynatrac Free-Spin Wheel Hub/Outer Axle Shaft Kit, Dynaloc® Lockout Kit, Torque King® greaseable axle u-joints, and spindle nut socket.

More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts

top_page
photo
QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals and Pinion Yokes

top_page
product note
2005-2010 Ford Super Duty 4x4 trucks with Dana 60 front axles use a two piece pinion sealing system. An outer wiper seal protects the inner oil seal from road debris. The seals are the same for all years and models. We stock the outer and both original equipment inner Pinion Seals for your Super Duty® F-250 and F-350 4x4 truck
photo
QU40397 Pinion Wiper V-Seal Protects QU40402 Pinion Seal from road splash.

Please refer to QU40397 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40402 Pinion Seal For 2005-2010 Dana Super 60 Front Axles in Ford F250 and F350 4x4 trucks
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40893 29 Spline Pinion Yoke Without Slinger For Dana 60 front alxes. 2005-Up Super Duty® and Super 60 front axles.

Also available while supplies last: QU40893U Used Pinion Yoke
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40709 U-Joint Strap and Bolt Kit For attaching the front driveshaft u-joint to your Dana 60 front pinion yoke
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note
Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else
photo
QU40022 Pinion Nut Is a single use nut that should be replaced anytime it has been removed.

Please refer to QU40022 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40023 Hardened Pinion Flat Washer Fits between the pinion yoke and pinion nut.

Please refer to QU40023 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40086 Ring Gear Bolt 12 of these nonreusable bolts are used to join the ring gear to the differential case.

Please refer to QU40086 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40099 Outer Pinion Slinger Fits between the pinion yoke and outer pinion bearing.

Please refer to QU40099 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40356 Pinion Preload Spacer Or crush sleeve fits between the outer pinion bearing and a shoulder on the pinion stem.

Please refer to QU40356 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40415 2005-2010 F250, F350 Hub to Knuckle Stud Is a genuine original equipment hardened, fine thread stud for 2005-2010 Ford Super Duty F250, F350 4x4 Front Axles.

Link to our QU40415 Catalog Product Page

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20081 Hub to Knuckle Flanged Nut Threads on QU40415 Stud to secure the wheel hub to the steering knuckle.

Link to our QU20081 Catalog Product Page

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Knuckles and Steering Knuckle Parts

top_page
photo
QU40415 2005-2010 F250, F350 Hub to Knuckle Stud Is a genuine original equipment hardened, fine thread stud for 2005-2010 Ford Super Duty F250, F350 4x4 Front Axles.

Link to our QU40415 Catalog Product Page

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20081 Hub to Knuckle Flanged Nut Threads on QU40415 Stud to secure the wheel hub to the steering knuckle.

Link to our QU20081 Catalog Product Page

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note
Dan the Gear Man® Product Note: Having the right special tool not only saves time, but it also minimizes the chance of damaging a part or yourself when working on your front axle. Some tools, like TS1530 Knuckle Seal Installer are an absolute necessity, others such as QT1158 Diff Bearing Installer can be real time savers, but are not indispensable
photo
TS1530 Knuckle to Axle Shaft Seal Installer for 2005-up Ford Super Duty® F-250, F350 4x4 Trucks Use to install those easily damaged and expensive QU20052 axle shaft to knuckle seals on your outer axle shaft. TS1530 is also used to correctly seat the seal and shaft assembly into the steering knuckle at the correct depth
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4511 Press Set Complete Tool Sets for replacing the pressed in Ball Joints on 2005-2010 Super Duty® F250 and F350 front drive axles. These Sets feature our long-throat M1065 C-Frame Press and the correct adapters to replace both original equipment and most aftermarket Ball Joints
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4647 Inner Seal Remover Set Is a real time saver! Driver slips through the axle shaft seal guides and knocks out those tricky inner axle shaft seals in a flash!

Please refer to QK4647 page for more details and ordering information.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1126 Universal Model 50/60 Inner Axle Shaft Seal Installer Fits all 1999-2004 Super Duty® and 2000-2005 Excursion Model 60 and Model 50 front drive axles. Depth that seal is installed is set by the operator. Use with QT1133 and QT1130 .

Please refer to QT1126 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1128 Model 60 Inner Axle Shaft Seal Installer with Depth Stop Fits all 1999-2004 Super Duty® 4x4 trucks with Dana-Spicer Model 60 front drive axles. Depth that seal is installed is controlled by the tool. Use with QT1133 and QT1130 .

Please refer to QT1128 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1130 Dana 60 Thrust Plate Is used in conjunction with QT1133 and QT1126 or QT1128 to install the Inner Axle Shaft Seals on your 1999-2004 Super Duty® 4x4 truck with Dana-Spicer Model 60 front drive axles.

Please refer to QT1130 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1133 Press Screw Assembly For Dana/Spicer Model 50 and 60 front drive axles. Use with the QT1126 or QT1128 Seal Installer and QT1130 Thrust Plate.

Please refer to QT1133 page for more details and ordering information.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4644 Model 60 Inner Axle Shaft Seal Tool Set Works on all 1999-2004 Ford Super Duty® Model 60 front drive axles. Quickly and easily presses in new original equipment inner axle seals without damage! Installation tool cups the seal so force is only applied on the outer shell. Kit includes QT1126 Model 50/60 Seal Installer, QT1130 Model 60 Thrust Plate, and QT1133 Press Screw Assembly.

Please refer to TS4644 page for more details and ordering information.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4807 Model 60 Inner Axle Shaft Seal Tool Set with Depth Stop Works on all 1999-2004 Super Duty® Model 60 front drive axles. Quickly and easily presses in new inner axle seals without damage! Installation tool cups the seal so force is only applied on the outer shell. Kit includes QT1128 Model 60 Depth Stop Seal Installer, QT1130 Model 60 Thrust Plate, and QT1133 Press Screw Assembly.

Please refer to TS4644 page for more details and ordering information.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT2005 Inner Pinion Bearing Installer Makes it easy to quickly install your inner pinion bearing without damaging the bearing or pinion. Use with shop press or hammer.

Please refer to QT2005 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1088 Differential Press Step Plate Is used when pulling and/or installing your differential bearings. These plates fit in the axle shaft hole of your differential. Use as a push plate for bearing removal or to support the differential when pressing on new bearings.

Please refer to QT1088 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1098 Differential Master Bearings Are an absolute necessity to determine differential shim pack dimensions. Required any time a ring and pinion set and or differential case is replaced or when the bore faces are trued. Precision machined from solid tool steel. Sold in pairs.

Please refer to QT1098 page for more details and ordering information.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1805 Inner Pinion Bearing Cup Installer Is used in conjunction with a Driver Handle and hammer to seat the inner pinion bearing cup in your front axle housing.

Please refer to QT1805 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1812 Outer Pinion Bearing Cup Installer Is used in conjunction with a Driver Handle and hammer to seat the outer pinion bearing cup in your front axle housing.

Please refer to QT1812 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1158 Differential Bearing Installer Makes a hard job easy. The raised inside ridge matches against inner differential bearing race allowing you to easily press or drive on QU50398 differential bearing until the bearing is fully seated against the differential adjusting shims
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT9205 Torx® Socket Bit for NV4500HD Output Shaft Nut and Ford Super Duty Hub-Locks ¼" drive socket is used to remove/install the lock out hub screws on 2005-up Ford Super Duty front axles