Parts for Dana-Spicer Model 80 Rear Axles in 1988-1998 Ford Trucks and 1996-2000 E350, E450 Vans

We have a good stock of original equipment replacement parts for 1988-2000 Ford Dana 80 Dual Rear Wheel Rear Axles. The Dana 80 is a hypoid gear, full floating rear axle that Ford used to equip many 1988-1998 Dual Rear Wheel (DRW) F-350 and F-450 Super Duty trucks plus heavy GVW 1996-2000 E-350, E-450 DRW van chassis models. There was a number of engineering changes during the 1988-1998 production period, however the basic axle design remained the same. A new generation of Dana 80 axles replaced the 1988-1998 versions starting with the Super Duty trucks in 1999. Ford dropped the Dana 80 for E-series van chassis models after 2000, but the Dana 80 was used on F53 Motor Home chassis models through 2008. See our 1999-2010 Dana 80 web page for 1999-2010 Super Duty trucks or 1999-2008 F53 motor homes.

Axle Identification

top_page
photo

Dana 80 Dual Rear Wheel Rear Axles in 1988-1991 Ford F-350, 1992-1998 F-450 Super Duty trucks, 1996-1999 E-350, and 1999-2000 E-450 van chassis have a Bill of Material Number (BOM) stamped on a Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows). The BOM number is a 6 digit number beginning with a 6 plus a dash number (ex: 605523-3). The BOM number can be used to determine not only the axle model, but also what components the axle was originally built with. We often ask for this number to insure we provide you with the exact parts you need for your truck.

Each different BOM number signifies an engineering part change which may be minor or major and may involve one or more parts. The dash number indicates the axle ratio and differential type (open or locking). Unfortunately, these tags are often missing on trucks that had prior differential service.

Axle Shafts and Axle Shaft Gaskets

top_page
photo
QU40078 DRW Van Steel Axle Shaft Flange to Hub Gasket Is an original equipment, embossed steel gasket that fits between the wheel hub and axle shaft flange on 1996-1999 Ford E-350 and 1999-2000 Ford E-450 Vans with Dana 80 rear axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40241 DRW Truck 8 Bolt Embossed Steel Hub Gasket Fits between the wheel hub and axle shaft flange on Ford Super Duty 1988-1991 F350 and 1995-1998 F450 trucks with Dana 80 Rear Axles. 4-5/16" Bolt Circle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
product note

Ford Dana 80 rear axles in 1988-1998 F350 and F450 trucks and 1996-1999 E-350 vans do not have rear anti-lock brake systems. 1999 and 2000 E-450 vans will also be equipped with a rear axle anti-lock brake systems.

photo
QU40294 ABS Tone Ring for Dana 80 Rear Axles in Ford DRW Vans Is a genuine original equipment toothed ring that is an interference fit on your 1999-2000 E450 Dana 80 differential case
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings (Individual)

top_page
product note

If you only need a bearing or two for your 1988-2000 Ford Dana 80 diff, we stock the best: Timken®. For the amount of work it takes to change most axle bearings, the extra cost for a Timken® diff or pinion bearing is a small price to pay for better steel, more uniform surface finish, and accurate, precision ground races.

photo
QU50402 Timken® Dana 80 Differential Bearing Cup For Dual Rear Wheel Dana 80 axles in 1988-1991 Ford Super Duty® F-350 trucks, 1992-1998 Ford F-450 Super Duty trucks, 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50403 Timken® Dana 80 Differential Bearing For Dual Rear Wheel Dana 80 axles in 1988-1991 Ford Super Duty® F-350 trucks, 1992-1998 Ford F-450 Super Duty trucks, 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50404 Timken® Dana 80 Outer Pinion Bearing Cup Dual Rear Wheel Dana 80 axles in 1988-1991 Ford Super Duty® F-350 trucks, 1992-1998 Ford F-450 Super Duty trucks, 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50405 Timken® Dana 80 Outer Pinion Bearing For Dual Rear Wheel Dana 80 axles in 1988-1991 Ford Super Duty® F-350 trucks, 1992-1998 Ford F-450 Super Duty trucks, 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50409 Timken® Dana 80 Inner Pinion Bearing Cup For Dual Rear Wheel Dana 80 axles in 1988-1991 Ford Super Duty® F-350 trucks, 1992-1998 Ford F-450 Super Duty trucks, 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50410 Timken® Dana 80 Inner Pinion Bearing For Dual Rear Wheel Dana 80 axles in 1988-1991 Ford Super Duty® F-350 trucks, 1992-1998 Ford F-450 Super Duty trucks, 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing Kits

top_page
product note

For your 1988-1998 Super Duty Truck or 1996-2000 Van with a dual rear wheel Dana 80 rear axle, we stock a standard Rear Dana 80 Differential Bearing and Seal Kit featuring the durability and precise fit of Timken® bearings.

photo
QU50437F Standard Differential Bearing and Seal Kit for Ford Dana 80 Rear Axles Fits Dana 80 Full Float Rear Axles in 1988-1998 Ford dual rear wheel Super Duty models. QU50437 features first class Timken® Differential and Pinion Bearings. Kit also includes aftermarket Pinion Seal, Pinion Nut, Gear Marking Compound, Threadlocker, and RTV Sealant
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40259 Differential Side Bearing Set For 1988-1998 Ford Super Duty® F350, F450 Dana 80 Dual Rear Wheel Axles are original equipment quality replacements. QU40259 Kit includes two each Bearing Cups and Tapered Bearings
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts (Open)

top_page
product note

When first introduced in the 1988 Ford Super Duty F-350, the Dana 80 Dual Rear Wheel (DRW) axle used 35 spline axle shafts. Effective with the 1990 model year, the axle spline size for Super Duty trucks was increased and the number of splines increased to 37. The 37 spline axle shaft was used on 1990-1991 F-350 and 1992-1998 F-450 models. The E-350 van chassis was available with an optional DRW Dana 80 axle with 35 spline axle shafts starting in 1996. all subsequent 1997-2000 Dana 80 equipped E-series 350 and 450 vans also used 35 spline axle shafts.

photo
QU40295F 35 Spline Dana 80 Differential Internal Parts Kit Genuine Dana Internal Diff Gear Set for DRW Dana 80 open differential Rear Axles in 1988-1989 Ford F-350 Super Duty DRW trucks, 1996-2000 E-350 Vans, and 1999-2000 E-450 vans
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40117 Differential Cross Shaft Retaining Pin Is a genuine Dana original equipment part for Dana 80 open differential Rear Axles in 1988-1991 Ford Super Duty® F-350 trucks, 1992-1998 Ford F-450 Super Duty trucks, 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Y452665 Yukon Dana 80 Chrome Rear Differential Cover for 1988-2010 1 Ton E-350, 2000-2005 E-450 Ford Vans and 1988-1998 F-350, 1990-1998 Super Duty F-450 Ford Trucks.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets, Gasket Maker & Covers

top_page
product note

Dana 80 Rear Axles in 1988-1991 Ford Super Duty F-350, 1992-1998 F-450 Dual Rear Wheel Trucks or 1996-2000 E-350, E-450 vans did not use differential cover gaskets. The Diff Cover is sealed with RTV sealant. The only gaskets used are steel gaskets between the wheel hub and axle shaft flange. Three different axle shaft flange gaskets were used of which we stock two types.

photo
S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Ford Dana 80
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40078 Axle Shaft Flange Gasket for 1996-2000 Ford E-350 and E-450 Vans With Dana 80 rear axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40241 DRW Truck 8 Bolt Embossed Steel Hub Gasket Fits between the wheel hub and axle shaft flange on Ford Super Duty 1988-1991 F350 and 1995-1998 F450 trucks with Dana 80 Rear Axles. 4-5/16" Bolt Circle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42031 Dana 80 Reusable Diff Cover Gasket by Spicer is a steel core performance gasket that can be reused multiple times. These Teflon® coated gaskets feature a no re-torque design and will save time when working on your diff. Fits all Dana 80 Ford rear axles 1988-1998.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

Y452665 Yukon Dana 80 Chrome Rear Differential Cover for 1988-1998 Ford E-350 1 Ton Vans, F-350 1 Ton, and F-450 Super Duty Trucks
More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals and Technical Information

top_page
product note

Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations.

photo
TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous

top_page
product note

Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts, chemicals, lubricants, and accessory items that do not neatly fit under our other parts headings.

photo
S24200 Blue Threadlocker For spindle and ring gear bolts etc
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90008 Gear Marking Compound Use with QT9404 Brush to check your ring and pinion gear tooth pattern
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S9975 Anti-Seize Lubricant Use between the spindle and knuckle mating surfaces to prevent rust bonding
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90018 Pyroplex® Protection ES Synthetic Grease Provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals and Yokes

top_page
product note

Ford used 1410 Series Pinion Yokes for 1988-1998 F-350 and F450 Dana 80 Rear Axles. E-Series Vans with the Dana 80 have a companion flange instead of an end yoke. The Pinion Seal is the same for both Vans and Super Duty trucks with Dana 80 Dual Rear Wheel rear axles.

photo
QU40716 F-350, F-450 1410 Series Pinion Yoke for 1988-1998 Ford Dana 80 Rear Axle Is a genuine original equipment yoke with a factory installed protective Cone Shaped slinger
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4651 1988-1998 Dana 80 Rear Pinion Yoke Kit Has all the genuine original equipment replacement parts you need to replace a worn or damaged pinion yoke
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40302 Ford Super Duty® Dana 80 Hydrodynamic Pinion Seal Is a genuine original equipment replacement Pinion Seal for DRW Dana 80 rear axles in 1988-1991 Ford Super Duty® F-350 trucks, 1992-1998 Ford F-450 Super Duty trucks, 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40709 Universal Joint Strap and Bolt Kit For 1988-1991 F-350 trucks, 1992-1998 Ford F-450 Super Duty dually trucks with 80 Rear Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20103 Van Driveshaft to Axle Flange Bolt Is a genuine original equipment 12 point metric bolt with pre-applied threadlocking compound. Use 4 of these bolts to attach your 1996-2000 E350, E450 van's rear driveshaft to your round pinion flange
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page

QU40646 1988-1995 5.13 Ratio Ring and Pinion Kit for Ford F350, F450 Dana 80 Rear Axle Is a genuine Dana gear set with pinion bearings, pinion seal, ring gear bolts, pinion nut, pinion washer, small parts, and shims. QU40646 fits Ford Super Duty Dana 80 Dual Rear Wheel axles in 1988-1991 F-350 and 1992-1995 F-450 trucks
More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

Y451688 3.54 Ratio Dana 80 Yukon High-Performance Ring and Pinion for 1988-2010 1 Ton E-350, 2000-2005 E-450 Ford Vans and 1988-1998 F-350, 1990-1998 Super Duty F-450 Ford Trucks
More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note

Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else.

photo
QU40343 Dana 80 Differential Cap Bolt With 3/4" hex head for all DRW Dana 80 Rear Drive Axles in 1988-1998 Ford Super Duty trucks and 1996-2000 E-Series heavy-duty van chassis. Long shoulder, hardened, Grade 8 bolt is a genuine Dana-Spicer original equipment part
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40261 1988-1995 Ford Dana 80 Differential and Pinion Shim Kit For Dana-Spicer Model 80 full float Rear Axles in 1988-1991F-350 and 1992-1995 F-450 Super Duty trucks. Genuine Dana-Spicer Shim Kit includes Pinion depth shims, pinion preload shims, differential adjusting shims, pinion nut, and pinion washer
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40213 1988-1995 Ford Dana 80 Differential Shim Kit For Dana-Spicer Model 80 full float Rear Axles in 1988-1991 F-350 and 1992-1995 F-450 Super Duty trucks. Genuine Dana-Spicer Shim Kit includes a selection of differential adjusting shims
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40096 Dana 80 Ring Gear Bolt Is a genuine original equipment Ring Gear Bolt for 1988-1991 F-350 and 1992-1995 F-450 Super Duty trucks with Dana 80 drive axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40095 Outer Pinion Slinger for 1988-1998 Ford Super Duty® Dana 80 Axles Is a genuine original equipment Slinger that fits between the outer pinion bearing and pinion yoke
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40568 1996-2000 Ford Dana 80 Differential and Pinion Shim Kit For Dana-Spicer Model 80 full float Rear Axles in 1996-1998 Ford F450 trucks and 1996-2000 E350, E450 Super Duty Dual Rear Wheel (DRW) vans. Genuine Dana-Spicer Shim Kit includes Pinion depth shims, pinion preload shims, inboard differential bearing adjusting shims, pinion nut, and pinion washer
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40606 1996-2000 Ford Dana 80 Outboard Differential Bearing Spacer Set Includes 13 sizes of thick steel genuine Dana Spacers ranging in size from 0.204" t 0.240". that fit between the differential bearing cups and axle housing on 1996 to 2000 Ford Super Duty Dana 80 Dual Rear Wheel rear axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20034 Inner Rear Wheel Bearing Oil Slinger For 1985-Current Ford Sterling and Dana 80 Rear Axles. Slinger fits between inner wheel bearing and spindle face.
Also available while supply lasts: QU20034U Good Used Inner Rear Wheel Bearing Oil Slinger
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Nuts and Spindle Hardware

top_page
product note

Spindle Nuts have two functions and they are to provide for correct wheel bearing adjustment and to keep your rear wheel hubs in place. 1988 to 1998 Ford F-Series Super Duty Dana 80 rear axles have several different spindle nut configurations. E-Series Super Duty Vans have only one. Ratchet type Spindle Nuts are reusable, but they often need replacement due to weakening of the tension spring or when the nut separates during removal. Given the critical job these nuts do, you should always replace any spindle nut that is not in perfect condition. The nuts from double spindle nut sets are also reusable, but the bend-over tab spindle lock washers are not.
1988-1991 F-350: Both QU40103 Left and QU40102 Right ratchet type Spindle Nuts
1992-1994 F-450 Right Hand Thread Double Spindle Nut Sets both sides (QU40239, QU40238, QU40237)
1995-1998 F-450 Right Hand Thread Single Nuts (Non Stocking Part)
1996-2000 E-Series Vans: QU40102 Right Hand Thread Ratchet Nut both sides

photo
QK4019 Rear Spindle Nut Set for 1988-1991 Ford F-350 Includes one left hand thread and one right hand thread ratchet style spindle nuts for 1988-1991 F350 Super Duty trucks with Dana 80 full float rear axles. Use to replace worn original nuts that have either separated or no longer "click" when adjusted
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40102 Right Hand Thread Ratchet Type Rear Axle Spindle Nut Is an original equipment, Hi-Shear, right hand ratcheting spindle nut for Ford Dana 80 full float DRW rear drive axles in 1988-1991 Ford F350 Super Duty Trucks (right side) and 1996 to 2000 E350, E450 vans (both left and right sides)
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40103 Left Hand Thread Ratchet Type Rear Axle Spindle Nut Is an original equipment, Hi-Shear, left hand ratcheting spindle nut for the drivers side on Ford Dana 80 full float DRW rear drive axles in 1988-1991 Ford F350 Super Duty Trucks
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40237 1992-1994 F-450 Spindle Nut Two of these reuseable, genuine original equipment, 6 slot, right hand thread spindle nuts are used for each spindle on 1992-1994 Ford F-450 Super Duty Dana 80 rear axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40238 1992-1994 F-450 Spindle Nut Lockwasher Is a genuine original equipment, non-reuseable, bend-over tab spindle lockwasher that is installed between the two spindle nuts on 1992-1994 Ford F-450 Super Duty Dana 80 rear axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40239 1992-1994 F-450 Spindle Thrust Lockwasher Is a genuine original equipment, reuseable, flat thrust washer that is installed between your outer wheel bearing and the inner spindle nut on 1992-1994 Ford F-450 Super Duty Dana 80 rear axles. LIMITED SUPPLY!
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 80 rear axle in your 1988-2000 Ford.

photo
QT1004 Inner Pinion Bearing Installer For 1988-1991 Ford Super Duty® F-350 trucks, 1992-1998 Ford F-450 Super Duty trucks, 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1088 Press Step Plate Used when Pressing Differential Bearings on or off
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1099 Differential Master Bearings Are used in conjunction with a dial indicator to determine the thickness of the differential shim packs for setting both backlash between the gears and the differential bearing preload
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1806 Inner Pinion Bearing Cup Installer For 1988-1991 Ford Super Duty® F-350 trucks, 1992-1998 Ford F-450 Super Duty trucks, 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1801 Outer Pinion Bearing Cup Installer For 1988-1991 Ford Super Duty® F-350 trucks, 1992-1998 Ford F-450 Super Duty trucks, 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1033 Differential Case Spreader For 1988-1991 Ford Super Duty® F-350 trucks, 1992-1998 Ford F-450 Super Duty trucks, 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1019 Spindle Nut Socket For removing or installing stock 4 slot ratchet spindle nuts on 1988-1991 F-350 Super Duty and 1996-2000 E350, E450 vans with Dana 80 Rear Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1503 E-Series Van Wheel Seal Installer For installing QU40449 Flanged Dual Rear Wheel Seal in 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models with Dana 80 rear axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1804 E-Series Van Inner Wheel Bearing Cup Installer For 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models with Dana 80 rear axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT9018 5 Pound Dead Blow Hammer Is just about the first tool you will reach for for a multitude of jobs on your Dodge Ram. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT9302 5 Pound Slide Hammer A first-class tool for pulling just about anything you can get a matching 5/8" fine thread puller attachment for
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals (Individual)

top_page
product note

1996-2000 Ford E-Series Vans with Dana 80 Dual Rear Wheel axles use the same rear wheel bearings for all years. The F-Series trucks will have different inner wheel bearings and outer wheel bearings depending upon year and model.

photo
QU50411 1996-2000 Ford E-Series Van Dana 80 Timken® Outer Wheel Bearing Cup For all 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models with Dana 80 rear axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50412 1996-2000 Ford E-Series Van Dana 80 Timken® Outer Wheel Bearing For 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models with Dana 80 rear axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50396 1996-2000 Ford E-Series Van Dana 80 Timken® Inner Wheel Bearing Cup For 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models with Dana 80 rear axles
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50399 1996-2000 Ford E-Series Van Dana 80 Timken® Inner Wheel Bearing For 1996-2000 E-350 van chassis, and 1999-2000 E-450 van chassis models with Dana 80 rear axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Seals (Individual)

top_page
product note

All 1996-2000 Ford E-Series Vans with Dana 80 Dual Rear Wheel axles use the same rear wheel seals. The F-Series trucks will have different wheel seals depending upon year and model.

photo
QU40449 1996-2000 Ford E-Series Van Inner Wheel Seal for Dana 80 Dual Rear Wheel Axles Is a genuine original equipment part
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Seal and Bearing Kits

top_page
product note

The rear wheel bearings in 1988-2000 Ford Dana 80 Rear axles average about 125, 000 miles before requiring replacement. Torque King® Premium Rear Wheel Bearing and Seal Kits for your Ford feature premium Timken® bearings and original equipment quality wheel seals because when it comes to rear wheel bearings and seals, only the best will do to safely support the heavy loads your truck hauls. To help you install these vital components properly, Torque King® Master Kits include bearing cup and wheel seal installers. Why use makeshift installation methods that can damage precision surfaces when affordable tools are available to do the job right the first time?

photo
TK8002/TK8003 1996-2000 E-Series Van Dana 80 Torque King® Rear Wheel Bearing Kits Include 4 Timken® Wheel Bearings with Cups, 2 Hydrodynamic Lip Wheel Seals, and 2 Axle Shaft O-Rings, Available as a Master Kit with Tools or as a parts only Kit
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!