Parts for 1990 to 1997 Ford Bronco II, Explorer, and Ranger Dana 35 IFS Twin Traction Beam Front Axles

The Dana 35 Twin Traction Beam Independent Front Suspension (IFS) front axle had a short production life of only 8 years. It was used in most 1990-1997 Ford Ranger pickups, some 1990 Bronco IIs, and all 1990-1994 Ford Explorers. The Dana 35IFS front axle is similar to the Dana 28IFS front axle used in previous Ranger pickups in that it uses one left axle beam that includes the differential assembly and one right axle beam, but most Dana 35 components are larger than the Dana 28. For the 1995 model year, the Dana 35 Twin Traction Beam front axle was replaced in the Explorer by a conventional IFS front axle that uses upper and lower control arms instead of axle beams. Original Equipment Parts support for the 1990-1997 Dana 35IFS Twin Traction Beam front axle is marginal from both Ford and Dana, however, we still can supply you with most needed parts using New Old Stock (NOS), aftermarket, and used parts sources.

Axle Beams

top_page
photo

QU20597U Used Right Axle Beam for Dana 35 IFS front axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20598 Used Left Axle Beam for Dana 35 IFS front axles.
More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shafts and Axle Shaft Small Parts

top_page
photo

QU40100 Axle Shaft Snap Ring For 1990 and newer Ford Bronco II, Explorer, and Ranger with Dana 28 or Dana 35 IFS front 4x4 drive axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20359 Short Disconnect Stub Shaft for 1995-1996 Ford Explorer.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42017 New Dana 35 Right Differential Output Shaft for Ford Bronco II, Ranger, and Explorer with Dana 35IFS front axles with standard u-joints.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42041 Left Inner Axle Shaft for 1990-1997 Ford Ranger, Bronco II, and Explorer with Dana 35IFS front axles.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20358U Used Right Axle Shaft Assembly for 1995-1997 Ford Rangers with Dana 35IFS front axles.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42090 Genuine Dana Left Axle Shaft Seal for Ford Dana 35IFS front axles.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
photo

QU20600U Used Differential Assembly for Dana 35 IFS 1997 Ford Ranger front axles with BOM 610652. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20606U Used Differential Housing for 1995-1997 Dana 35 IFS Ford Ranger front axles. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hubs

top_page

QU20595U Pancake Hub for 27 spline Dana 35 IFS Ford Ranger

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU56137 Warn 29071 27 Spline Manual Lockout Hub Set for 1990-1997 Ford Ranger and 1990-1994 Ford Explorer Dana 35IFS Front Axles

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Parts

top_page
photo

QU20607U Used Pinion Yoke for 1990-1997 Dana 35 IFS front axles in 1990-1997 Rangers and 1990-1994 Ford Explorer with Cardan and CV joints. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU42043 Pinion Slinger/Shim Package for Ford Dana 35IFS front axles.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
photo

QU20599U Used Ring and Pinion Set with 3.73 ratio for 1990-1997 Dana 35 IFS front axles in 1990-1997 Rangers and 1990-1994 Ford Explorer. For trucks with the following BOM numbers: 610300, 610365, 610366, 610410, 610419, 610436, 610437, 610483, and 610652. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
photo

QU20093 27 Spline, 3 Piece Axle Shaft Thrust Washer Set For automatic hub equipped, 1995-1997 Ford Ranger with Dana 35 IFS front axles. QU20093 can also be used to replace discontinued QU40101 one piece thrust washer on 1990-1994 axles.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40100 Axle Shaft Snap Ring For Ford Ranger and Bronco II. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Bearings and Seals

top_page
photo

QK4734 Front Axle Shaft Spindle Bearing Set Fits all 1990-1992 Ford Bronco II, 1990-1994 Ford Explorer and 1990-1997 Ford Ranger 4x4s with Dana 35IFS Twin Traction Beam® front axles. One bearing is pressed into each spindle to support the outer axle shaft. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40056 1990-1992 Small Spindle to Axle Shaft V-Seal Is a genuine original equipment 1-5/16" ID Rubber V-Seal that is installed in your spindle between QK4734.5 Spindle Bearing and QU40070 Spindle Thrust Washer. Fits 1990-1992 Ford Bronco II, 1990-1994 Ford Explorer and 1990-1997 Ford Ranger 4x4s with Dana 35IFS Twin Traction Beam® front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40070 1990-1992 Axle Shaft to Spindle Thrust Washer Is a genuine original equipment plastic thrust washer that controls axial thrust between your outer axle shaft and spindle. Fits 1990-1992 Ford Bronco II, 1990-1994 Ford Explorer and 1990-1997 Ford Ranger 4x4s with Dana 35IFS Twin Traction Beam® front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40071 1990-1992 Large Axle Shaft to Spindle V-Seal Is a genuine original equipment 2.25" ID Rubber V-Seal that seals between your axle shaft and spindle. Fits 1990-1992 Ford Bronco II, 1990-1994 Ford Explorer and 1990-1997 Ford Ranger 4x4s with Dana 35IFS Twin Traction Beam® front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4739 1990-1992 Spindle Seal Kit Services both sides on your 1990-1992 Ford Bronco II, 1990-1994 Ford Explorer or 1990-1997 Ford Ranger 4x4 with Dana 35IFS Twin Traction Beam® front axles. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40228 1983.5-1992 Spindle Bearing and Seal Kit Services one side on your 1990-1992 Ford Bronco II, 1990-1994 Ford Explorer or 1990-1997 Ford Ranger 4x4 with Dana 35IFS Twin Traction Beam® front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40058 1990-1992 Outer Axle Shaft Slinger Acts as both as a crud deflector and a sealing surface on open knuckle axles. Replace anytime they are dinged, bent or badly corroded. Fits 1990-1994 Ford Explorer and 1990-1997 Ford Ranger 4x4s with Dana 35IFS Twin Traction Beam® front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40436 1993-1994 Outer Axle Shaft/Spindle Seal and Bearing Set Has the genuine original equipment axle support bearing and spindle seals needed to service ONE side on your 1993 or 1994 Ford Ranger or Ford Explorer 4x4.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40459 1993-1994 Press On Axle Shaft to Spindle Seal Is a genuine original equipment seal that is installed on your outer axle shaft. Fits 1990-1994 Ford Explorer or 1990-1997 Ford Ranger 4x4 with Dana 35IFS Twin Traction Beam® front axles.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindles and Spindle Nuts

top_page
product note

The three piece spindle nut sets used on vehicles with manual hubs are neither compatible nor interchangeable with the single rounded hex nut used with auto hubs. If you are replacing an auto hub set with manual hubs, you MUST also replace the spindle nuts.

photo

QK4769 Spindle Nut Kit Is a genuine Dana original equipment 3 piece Spindle Nut Set for 1990-1997 Ranger Pickup, 1990-1992 Bronco II, and 1990-1994 Ford Explorer with Model 35 Axles and 27 Spline Manual Locking Hubs. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20601U Used Spindle for 1997 Dana 35 IFS front axles Ford Rangers. More Info
For use in trucks with the following BOM numbers: 610418, 610419, 610652, and 610653

photo

QU40631 1990-1997 Dana 35 Spindle Is a new bare front spindle for 1990-1992 Ford Bronco II, 1990-1994 Ford Explorer and 1990-1994 Ford Ranger Dana 35 IFS front axles. Also fits 1995-1997 Ranger with 4 wheel ABS. QU40631 is a genuine Dana factory part.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Y440631 Replacement Spindle for 1990-1997 Dana 35IFS is a low cost, yet high quality replacement part. Imported.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40108 Outer Spindle Nut without pin for Dana 35 front axles with manual hubs in 1990-1997 Ford Bronco II, Explorer, and Ranger.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40060 1990-1997 Spindle Lock Washer for Manual Hub Equipped Dana 35IFS Front Axles is a genuine original equipment part for your manual hub equipped 1990-1997 Ford Ranger or 1990-1994 Ford Explorer Dana 35 Twin Traction Beam front axle. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40123 Inner Spindle Wheel Bearing Nut with Pin for Dana 35IFS front axles with manual hubs in 1990-1997 Ford Bronco II, Explorer, and Ranger.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Knuckles

top_page
photo

QU20604U Used Right Knuckle for 1995-1997 Dana 35 IFS Ford Ranger front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20605U Used Left Steering Knuckle for 1995-1997 Dana 35 IFS Ford Ranger front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

We stock popular tools for the Dana 35 Twin Traction Beam Beam IFS Front Axle in Ford Rangers and Explorers.

photo

QT1012i 4 Lug 4x4 Front Spindle Nut Socket for Dana 35IFS Axles with Manual Hubs fits 4 slot spindle nuts used on manual hub equipped Dana 35IFS front axles in 1990-1997 Ford Ranger and 1990-1994 Ford Explorer 4x4s. Use to remove and install the 4-slot inner and outer spindle nuts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1059 and QT1059i 2-3/8" Rounded Hex Spindle Nut Socket for Dana 35IFS Axles with Automatic Hubs removes and installs the 2-3/8" rounded hex spindle nuts on 1990-1997 Ford Ranger and 1990-1994 Ford Explorer 4x4's equipped with factory automatic locking hubs. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Wheel Seals

top_page
product note

The inner and outer wheel bearing parts are identical for all 1990-1992 Bronco II, 1990-1994 Ford Explorer and 1990-1997 Ford Ranger 4x4s with Dana 35IFS Twin Traction Beam® Front Axles. However, the wheel seals are different for 1990-1994 and 1995-1997 model years.

photo

QU50577 Timken® Wheel Bearing Cup For 1990 to 1994 Ford Explorer and 1990-1997 Ranger Dana 35 Independent Front Suspension (IFS) front axles. Uses two cups per side. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50578 Timken® Wheel Bearing For Dana 1990 to 1994 Ford Explorer and 1990-1997 Ranger Dana 35 Independent Front Suspension (IFS) front axles. Uses two bearings per side. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU90001 1990-1994 Front Wheel Seal for Ford Dana 35IFS Front axles is a high quality oil and grease seal with a garter spring plus an outer wiper lip that fits 1990 to 1994 Ford Explorer and 1990-1994 Ranger Dana 35 Independent Front Suspension (IFS) front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!