Rear Driveshaft Parts for Ford Excursion and 1999-2004 Ford Super Duty® Trucks

We stock a comprehensive selection of replacement parts and service tools for 1999 to 2004 Ford Super Duty® F-250/F-350/F-450/F-550 4x4 trucks and 2000-2005 Ford Excursion 4x4 SUVs.

Ford Excursion and Super Duty® trucks have a number of rear driveshaft configurations depending upon year, truck model, engine, transmission, and wheel base. To insure you order the correct replacement parts, YOU must verify the parts your driveshaft has using the section below.

Ford introduced the first factory equipped 4x4 Super Duty® trucks in 1998 as 1999 model year vehicles. Prior to that time, the Super Duty name was used exclusively on 4x2 dual rear wheel chassis cab commercial work trucks. Engines used include the 5.4L gas V8, 6.8L gas V10, 7.3L Diesel, and 6.0L Diesel. Due to the large number of cab, wheel base, power train, and Gross Vehicle Weight choices offered by Ford, Super Duty® driveshaft components will vary considerably. The Excursion was introduced as a 2000 model year vehicle. Production continued until the end of the 2005 model year, although some late production Excursions were marketed in Mexico as 2006 vehicles. Excursion rear driveshaft choices are not nearly as varied as the Super Duty® truck, but variations will be found depending upon year, engine, and transmission.

Driveshaft Identification

top_page
product note

Ford used a great variety of rear drive shaft configurations for the 4x4 Excursion and 1999-2004 Super Duty® trucks. Before ordering rear driveshaft parts for your 4x4, you have to identify the part types used on your driveshaft. Ford used both Double Cardan* Constant Velocity and Single Cardan* rear driveshafts. Three different u-joints sizes are possible along with different sizes and types of slip joints. All the 4x4 Rear Driveshafts use steel tubing. Although many of the parts we list on this page will fit 4x2 trucks with steel driveshafts, we are unable to give specific 4x2 fitment information as 4x2 trucks are exceedingly rare around our mile high Montana headquarters. We do not offer parts for those 4x2 trucks with aluminum driveshafts.

*Cardan is a tech term used to describe the common cross type universal joint.

photo

Shaft Type, Single or Double Cardan: Excursion and Most Ford Super Duty® 4x4 Rear Driveshafts use a Single Cardan u-joint at the upper, transfer case end of the driveshaft. Most 137" and 142" wheel base F-250 and F-350 trucks have a Double-Cardan Constant Velocity Joint at the Transfer Case End.

Click on Picture to Enlarge Image

photo

1 Piece or 2 Piece Driveshaft: These terms are a bit misleading as obviously driveshafts have more that one or two pieces, but of course they refer to the number of shaft assemblies or subassemblies used to construct the entire driveshaft. One piece driveshafts, which are used in shorter wheelbase models, have a single tube with a slip joint at one end and either a single or double Cardan Joint at the other end. Two Piece driveshafts are found in longer wheel base trucks and they will comprise of two sub-assemblies joined at the middle by a single Cardan u-joint. A two piece shaft will have a total 3 single Cardan u-joints and utilize a center bearing (midship support) at the stub shaft welded to the rear of the first tube.

Click on Picture to Enlarge Image

photo

Rear U-Joint to Axle Attachment: Depending upon the drivetrain configuration, the rear universal joint may have a flange yoke that bolts to a matching pinion companion flange OR a u-joint that directly attaches to a pinion end yoke with straps and bolts.

Click on Picture to Enlarge Image

photo

U-Joint Sizes: Ford used three different size universal joints depending upon the driveshaft type, vehicle model, wheel base, and engine. The Small size universal joint has 1-3/16" diameter cups and is 3-5/8" wide. The small u-joint was used in some vehicles with 5.4 liter engines and all Double Cardan CV joints. The Medium size u-joint also has 1-3/16" cups, but the width is 4-3/16". This joint was used at the rear axle on Double Cardan CV shafts and for all positions on Single-Cardan shaft equipped F-250-350 Diesel and V-10 trucks, plus many 5.4L Excursions and Super Dutys. The Large size u-joint which was used exclusively in F-450 and F-550 trucks features 1-3/8" diameter cups and 4-3/16" overall width.

Click on Picture to Enlarge Image

photo

Slip Yoke Boot: Depending upon the size of the slip joint splines, Ford Excursion and 1999-2004 Super Duty® Rear Driveshafts will have 3 pleat, 4 pleat, or 5 pleat slip joint boots. The boots and clamps for 3 pleat boots are not interchangeable with 4 or 5 pleat types.

Click on Picture to Enlarge Image

photo

Midship Coupling and Center Bearing: Ford used 2 types of midship couplings on longer wheel base Super Duty trucks with 2 piece driveshafts. With the Slip Coupling type, a female slip yoke on the forward end of rearward driveshaft fits over the long male spline slip stub that is part of the forward driveshaft. With a Fixed Coupling, both parts of the Slip Joint and the center universal joint are part of the rearward shaft. The back of the forward shaft has a fixed, half-round end yoke to which the center u-joint is secured using straps and bolts. In either case, the Center Bearing Assembly is the same, however some service procedures to replace the Bearing will differ.

Click on Picture to Enlarge Image

Boots and Boot Clamps

top_page
product note

Ford Excursion and 1999-2004 Ford Super Duty® 4x4 trucks have a rear driveshaft slip joint protected by a rubber boot. A boot protected driveshaft slip joint will usually outlast the truck as as long as the boot is intact and there is some grease on the splines. If your Boot is damaged, REPLACE IT! If your Boot is OK, but you are doing other driveshaft service, always clean and grease the splines AND replace the clamps!

photo
QU40883 3 Pleat Rear Drive Shaft Boot Kit for Ford Excursion and 1999-2004 Ford Super Duty® Fits shafts that have 24 spline slip stub splines over 1-1/2" in diameter. Genuine original equipment Kit includes Slip Yoke Boot and one each QU40884 and QU40885 Boot Clamps
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40884 Small Driveshaft Boot Clamp For the small (Slip Stub) end of slip joint boots used on Ford Excursion and 1999-2004 Ford Super Duty rear driveshafts with 3 Pleat rear slip joint boots
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40885 Large Driveshaft Boot Clamp For the large (Slip Yoke) end of slip joint boots used on Ford Excursion and 1999-2004 Ford Super Duty rear driveshafts with 3 Pleat rear slip joint boots
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40128 4 Pleat Rear Driveshaft Boot Kit for Ford Excursion and 1999-2004 Ford Super Duty® trucks Genuine original equipment Kit includes Slip Yoke Boot and one each QU40084 and QU40133 Boot Clamps for use on Excursion and Super Duty trucks with 16 spline or 22 spline Slip Stub Splines that are 1.5" in diameter or smaller. QU40128 replaces both 4 and 5 pleat original equipment Slip Joint Boots. QU40128 is also the current replacement Boot for vehicles that originally had 5 pleat boots.
See our QU40128 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40133 Small Boot Clamp for 4 Pleat Rear Driveshaft Boots Fits the small (Slip Stub) end of slip yoke boots used on Ford Excursion and 1999-2004 Ford Super Duty® rear driveshafts with 4 Pleat or 5 Pleat rear slip joint boots
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40084 Large Boot Clamp for 4 Pleat Rear Driveshaft Boots Fits the large (Slip Yoke) end of slip yoke boots used on Ford Excursion and 1999-2004 Ford Super Duty® rear driveshafts with 4 Pleat or 8 Pleat rear slip joint boots
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Center Bearings

top_page
product note

The maximum length a steel tube driveshaft can run without support is about 5'. For most 4x2 and longer wheel base 4x4 trucks, this means a two part rear driveshaft (Propeller Shaft) with a pressed on Center Bearing (also known as Midship Support Bearing or Carrier Bearing) must be used to support the center of the driveshaft.

photo
QU40886 Rear Driveshaft Center Bearing For 1999-2004 Ford Super Duty Trucks Is a genuine original equipment replacement Kit that included the Center Bearing and both front and rear Slingers. Use QU40886 for all 1999-2004 Ford Super Duty trucks with 2 piece rear driveshafts
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Double-Cardan Constant Velocity Parts

top_page
product note

Some Shorter Wheel Base Ford Super Duty® trucks used a Double Cardan Rear Constant Velocity Driveshaft. The CV Joint is at the front of the driveshaft. Although the slip joint and rear u-joint are often identical to those used on some trucks with conventional driveshafts with the same engine, NONE of the CV specific parts are interchangeable with any of the parts used on regular driveshafts.

photo
QU40901 1350 Series Greaseable Ball Stud Tube Yoke For 1999-2004 Super Duty® F-250, F-350 Double-Cardan Constant-Velocity rear driveshafts
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40800 1350 series CV Center Yoke For 1999-2004 Super Duty® F-250, F-350 Double-Cardan Constant-Velocity rear driveshafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40868 Rear Driveshaft CV Flange Yoke for 1999-2004 Ford Super Duty Is a USA made replacement part for all 1999-2004 Ford Super Duty trucks with Double Cardan rear constant velocity driveshafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40704 Press On Outer Dust Seal For 1999-2004 Ford Super Duty trucks with Double-Carden Driveshaft Constant Velocity Joints. This seal helps protect the CV Centering Ball from road splash and should be replaced any time the u-joints are changed
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40744 CV Ball Replacement Kit Fits 1999-2004 Ford Super Duty trucks with Double-Carden Driveshaft Constant Velocity Joints. This money saving Kit allows you to reuse the cast iron CV Flange Yoke (QU40868 )
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40829 Spicer Type Ford 1999-2004 Super Duty Rear Replacement CV Grease Seal For 1999-2004 Ford Super Duty® F-250, F-350, F-450, F-550 with Rear Double-Cardan CV Joint. This part is included in QU40744 Ball Kit and is part of QU40868 CV Flange
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40835 Spicer Type 1999-2004 Ford Super Duty Replacement Front CV Joint Tension Spring For 1999-2004 Ford Super Duty® F-250, F-350, F-450, F-550 with Rear Double-Cardan CV Joint. This part is included in QU40744 Ball Kit and with QU40868 CV Flange
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Driveshaft Assemblies

top_page
product note

Our inventory of complete rebuilt driveshaft assemblies changes constantly due to a shortage of good rebuildable cores. For new driveshafts, we offer unfinished, fully greaseable heavy duty 1350 x 1350 and 1350 x 1410 series Double Cardan CV Shafts. The 1350 series CV joint (u-joint width is 3-5/8") is the same for all trucks, but two different rear u-joints were used. Trucks with small gas engines typically have a 3-5/8" wide u-joint in the slip yoke. Most V10 and Diesel trucks will use a 4-3/16" wide joint to attach to the rear axle. Check your rear u-joint width before ordering!

photo
QU40861 1350x1410 Unfinished Greaseable Rear CV Drive Shaft Assembly For 1999-2004 Ford Super Duty® is the lowest cost way to replace your worn out Double Cardan Constant Velocity Ford Super Duty rear driveshaft with a brand new, totally greaseable, heavy duty Double Cardan Constant Velocity front driveshaft that you customize for length and complete the final assembly. Slip Yoke U-Joint is 4-3/16" wide
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40894 1350x1350 Unfinished Greaseable Rear CV Drive Shaft Assembly For 1999-2004 Ford Super Duty® is the lowest cost way to replace your worn out Double Cardan Constant Velocity Ford Super Duty rear driveshaft with a brand new, totally greaseable, heavy duty Double Cardan Constant Velocity front driveshaft that you customize for length and complete the final assembly. Slip Yoke U-Joint is 3-5/8" wide
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Flange Yokes, Single Cardan

top_page
product note

Single Cardan Flange Yokes are used at one or both ends of most Ford Excursion and Ford Super Duty® rear driveshafts. A flange yoke is part of the driveshaft assembly. To order a replacement Flange Yoke, you need to know the size of your u-joint AND verify if the Pilot Diameter of the Flange Yoke you require. On most, BUT NOT ALL driveshafts, the Front Flange Yoke (Transfer Case) and Rear Flange Yoke (axle) are different. A female pilot hole in the Flange Yoke will mate up to a matching male pilot on the transfer case or axle companion flange. Order four QU20103 Bolts to secure your new Flange Yoke to the matching companion flange

photo
QU40820 Small Pilot Ford Excursion and Super Duty Rear Driveshaft to Transfer Case Flange Yoke Fits all single Cardan Ford Excursion and 1999-2004 Ford F-250, F350 Super Duty Rear Driveshafts that use Medium Size (4-3/16" wide, 1410 Series) rear driveshaft universal joints and mate to a Transfer Case Companion Flange with an approximate 2-11/16" male pilot . This Flange Yoke is typically used on vehicles with Diesel or V10 gas engines
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40887 Medium U-Joint/Large Pilot Ford Excursion and Super Duty Rear Driveshaft Flange Yoke Is a female pilot flange yoke that fits Ford Excursion and 1999-2004 Ford F-250, F350 Super Duty Rear Driveshafts that use Medium Size (4-3/16" wide, 1410 Series) rear driveshaft universal joints and mate to a transfer case or rear axle companion flange with an approximate 2-61/64" male pilot . This Flange Yoke is typically used on vehicles with Diesel or V10 gas engines
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40696 Large Pilot Ford Excursion and Super Duty Rear Driveshaft Flange Yoke Is a female pilot Flange Yoke that fits Ford Excursion and 1999-2004 Ford F-250, F350 Super Duty Rear Driveshafts that use Small Size (3-5/8" wide, 1350 Series) rear driveshaft universal joints and mate to a transfer case or rear axle companion flange with an approximate 2-61/64" male pilot . This Flange Yoke is typically used on vehicles with V8 gas engines

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals

top_page
product note

An awful lot of driveshaft parts are wrecked by the slam-bang methods of universal joint replacement used by most people doing driveshaft service. Your Double Cardan driveshaft components are machined to incredibly precise specifications and can be easily damaged by either poor service procedures or makeshift tools (or both). Our Driveshaft Manuals guide you through the various driveshaft service jobs using clear color photographs and detailed text.

photo
TM3000 Driveshaft and Universal Joint Service Manual Complete driveshaft repair and service manual has over 300 color photographs! Topics include: History, Safety, General Service, Inspection, Driveshaft Removal/Reinstallation, External Snap Ring Service, Internal Snap Ring Service, Double Cardan Constant Velocity Techniques, Center Bearing Replacement, Slip Yoke Service, Exploded Views, Part Descriptions, Identification/Sizing, Torque Specs, Special Tools, and technical subjects such as Balance and Angles. 80 total pages with 74 pages of indispensable information on how to properly service and maintain your driveshafts (also known as propeller shafts). See our TM3000 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TSB3502 External Snap Ring Single Cardan U-Joint Service. Driveshaft and Universal Joint Technical Service Bulletin 5 tech pages, 21 color photos, 6 total pages. See our TSB3502 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous

top_page
product note

Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings

photo
QU90018 Pyrople® Protection ES Synthetic Grease Provides extended service protection under the harshest on and off road conditions! This new NLGI #2 GC-LB grease is Hydro-Activated™ to become tackier when exposed to moisture. Offers superior corrosion and wear protection in a variety of environments. Provides excellent low and high temperature performance. Use to lubricate the CV Ball and Slip Yoke prior to assembly and for your greaseable universal joints
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S9978 Medium Strength Blue 242 Threadlocker Is used on the bolt threads that attach your driveshaft to the transfer case and front axle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S9975 Anti-Seize Lubricant Will keep the CV flange from rusting to the rear axle or transfer case flange when applied the male-female pilot that centers the shaft flange to the gearbox flange
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Slip Yokes

top_page
product note

Ford used a number of different Rear Driveshaft Slip Yokes for the Excursion and 1999-2004 Super Duty® 4x4 vehicles. You need to know the U-Joint size and the number of splines on the male Slip Stub. At this time, we only stock Slip Yokes for the most common 22 and 24 spline Ford Super Duty® rear driveshaft applications with a Medium Size U-Joint in the Slip Yoke

photo
QU40888 Slip Yoke for 22 Spline 1999-2004 Ford Super Duty Rear Driveshafts Fits both CV and 2 piece driveshafts with 22 spline Slip Stubs. Takes medium series universal joints (1-3/16" cup x 4-3/16" overall joint width)
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40890 Slip Yoke for 24 Spline 1999-2004 Ford Super Duty Rear Driveshafts Fits fits both CV and 2 piece driveshafts with 24 spline Slip Stubs. Takes medium series universal joints (1-3/16" cup x 4-3/16" overall joint width)
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40875 Greaseable Slip Yoke for Replacement Rear Driveshafts with 3-5/8" Wide U-Joints Fits gas engine Ford Excursions and Super Duty models that use aftermarket replacement 16 spline Slip Stubs or driveshafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note

Driveshaft attachment hardware is one of the most overlooked components requiring frequent replacement. Ford used bolts with factory pre-applied Threadlocker on the bolt threads. While you can reuse these bolts if you use liquid Threadlocker, you can not compensate for either head wear or bolt fatigue. Replacing your driveshaft attachment hardware when performing other driveshaft service is good preventative maintenance

photo
QU40709 Driveshaft to Front Pinion Yoke Universal Joint Strap and Bolt Kit for Is a genuine Spicer original equipment Kit that has two u-joint bearing straps and four 5/16" hardened, fine thread Flange Head Bolts to couple both Saginaw type and Spicer type front Double Cardan CV driveshafts to the front axle on all 4x4 Ford Excursion and 1999-2004 Ford Super Duty trucks
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20103 Driveshaft to Transfer Case Bolt Is a genuine original equipment 12 point metric bolt with pre-applied threadlocking compound. Use 4 of these bolts to attach your Excursion or Super Duty driveshaft flange to your round transfer case or axle flange
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40889 Ford Super Duty Rear Driveshaft Yoke Nut For Super Duty trucks with Fixed Type two-piece rear driveshafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

Most CV and universal joint service is done using makeshift tools and hammering on the parts until something gives service methods. Driveshaft parts and universal joints are incredibly precise components that can be easily damaged by such slam-bang work. There is a better way to perform driveshaft service using application specific press tooling and approved service procedures. Yeah, I know the Manuals and Tools are expensive, but when you consider that a poorly installed front u-joint blowing out as you tool down the Interstate at 75 is going to cause an expensive and dangerous mess. I have witnessed several driveshaft failures in vehicles driving ahead of me during my travels and I can tell you a 3' long front driveshaft can do a heck of a lot of damage as it whips around jamming into the road, whacking the transmission, and smashing the floor!

photo
QT1065 Series Long Throat C-Frame Ball Joint Press Is designed to accept a variety of interchangeable tooling for performing Ball Joint and Universal Joint service on your 4x4. A heavy-duty tool that will get the job done when used with the appropriate tooling for your big Ford.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT4008 Medium Size U-Joint Separator Yoke Is used with a QT1065 series C-frame Press and QT4016 Press Anvil to easily remove the Small and Medium universal joints on Ford Excursion and Ford F-250, F-350 Super Duty rear driveshafts. By placing the press force against the u-joint cross, the amount of pressure needed to break a cup free is halved, and the chances of damaging the yokes is greatly reduced. Works on rusted in or tight fitting u-joints
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT4010 1" Press Tip Is used with a QT1065 series C-frame Press and QT4016 Press Anvil to easily install universal joints with 1-1/16" to 1-3/16" diameter cups on most common light truck driveshafts and 4x4 front axle shafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT4016 1-1/16" to 1-3/16" Capacity U-Joint Press Anvils Used with a QT1065 series C-frame Press and either QT4008 Medium U-Joint Separator Yoke or QT4010 1" Press Tip to easily remove and install Small and Medium universal joints from Ford Excursion or Ford F-250, F-350 Super Duty rear driveshafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT4009 Large Size U-Joint Separator Yoke Is used with a QT1065 series C-frame Press and QT4015 Press Anvil to easily remove the Large universal joints on Ford F-450, F-550 Super Duty rear driveshafts. By placing the press force against the u-joint cross, the amount of pressure needed to break a cup free is halved, and the chances of damaging the yokes is greatly reduced. Works on rusted in or tight fitting u-joints
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT4011 1-1/4" Press Tip Is used with a QT1065 series C-frame Press and QT4015 Press Anvil to easily install universal joints with 1-3/8" diameter cups on heavy-duty light truck driveshafts and 4x4 front axle shafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT4015 1-3/8" Capacity U-Joint Press Anvils Used with a QT1065 series C-frame Press and either QT4009 Medium U-Joint Separator Yoke or QT4011 1" Press Tip to easily remove and install Large universal joints from Ford Ford F-450, F-550 Super Duty rear driveshafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1021 12 Point Impact Socket For removing/installing QU20103 12 point Driveshaft Flange to Axle Shaft Companion Flange Bolts on Ford Excursions and 1999-2004 Super Duty trucks
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tubing

top_page
product note

Ford used 3.5" outside diameter alloy driveshaft tubing with welded seams for almost all Ford Excursion and 1999-2004 Ford Super Duty Rear Driveshafts. Driveshaft tubing is typically more concentric, straighter, and has a higher Rockwell hardness rating when compared to general purpose tubing. A driveshaft needs to be retubed any time the tube is bent, dinged, or creased. Retubing a driveshaft is best done by a qualified driveline shop that can balance the finished assembly, however any competent machinist with a long bed lathe can successfully retube a driveshaft. See TM3000 Driveshaft Manual or TSB3510 download for driveshaft assembly runout specifications.

photo
We stock and sell by the inch, the 3.5" outside diameter steel rear Driveshaft Tubing used for Ford Excursion and 1999-2004 Ford Super Duty rear driveshafts We stock and sell by the inch, the 3.5" outside diameter steel rear Driveshaft Tubing used for Ford Excursion and 1999-2004 Ford Super Duty rear driveshafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tube Yokes

top_page
product note

Tube Yokes typically get damaged when a worn u-joint lets go under load or from getting tweaked using excessive force when replacing universal joints. Replacing Tube Yokes is best done by a qualified driveline shop that can balance the finished assembly, however any competent machinist with a long bed lathe can successfully replace tube yokes. Ford used different size rear driveshaft universal joints depending upon the year, engine, transmission, and truck model. Verify your tube diameter and u-joint size before ordering! See TM3000 Driveshaft Manual or TSB3510 download for driveshaft assembly runout specifications

photo
QU40865 Tube Weld Yoke for 3.5" Diameter Driveshafts Replaces broken or bent original equipment Ford Excursion or Super Duty® tube yokes made for Medium size u-joints
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Universal Joints

top_page
product note

We offer you the choice between our premium quality, very long lasting, Torque King® cold-forged, alloy steel, non-greaseable factory synthetic-lubed u-joints or greaseable hot-forged universal joints. Both are the best quality u-joints available in their classes to keep your Ford rolling down the road

photo
TK40719 Torque King® Premium Quality, Non-Greaseable Small Series Driveshaft U-Joint With cold-forged, alloy steel cross, synthetic-lubricant, superior seals and External Snap Rings fits all three positions of both Saginaw type and Spicer type front Double Cardan CV driveshafts for all 4x4 Ford Excursion and 1999-2004 Ford Super Duty
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40731 Greaseable Small Series Universal Joint Is a very good quality American made universal joint universal joint with a hot-forged cross suitable for all three positions of both Saginaw type and Spicer type front Double Cardan CV driveshafts for all 4x4 Ford Excursion and 1999-2004 Ford Super Duty
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40873 Easy-Grease Greaseable Small Series Universal Joint Has one cup drilled and tapped for a supplied grease fitting so you can easily grease your u-joints in tight quarters
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK40705 Torque King® Premium Quality, Non-Greaseable Driveshaft U-Joint Cold-Forged, Alloy Steel, Non-Greaseable Factory Synthetic-Lubed U-Joints with External Snap Rings for 4x4 Ford Excursion and 1999-2004 Ford Super Duty
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40789 Greaseable Medium Series Universal Joint Hot-Forged, Standard Duty, Alloy Steel, Greaseable U-Joints for 4x4 Ford Excursion and 1999-2004 Ford Super Duty. Dan the Gear Man® Tech Note: Although inexpensive, Hot-Forged U-Joints are Not Recommended for Diesel or V-10 Rear Driveshaft Applications, use TK40705 for Powerstroke® Diesel and V-10 models.
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK40497 Torque King® Large Greaseable Rear Driveshaft U-joint for Ford Super Duty F-450 and F-550 Trucks is a cold-forged alloy steel greaseable u-joint with superior seals for long life under the most adverse conditions
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!