Front Axle Parts and Tools for 1969-1972 Chevy and GMC 4x4 Dana 44 Open Knuckle Front Axles

We have a good selection of parts for 1969 to 1972 Chevy and GMC Dana 44 open knuckle front driving axles. General Motors first used the open knuckle Dana 44 front axle in the 1969 Chevy Blazer (The GMC Jimmy was not released until 1970). According to the GM Parts Books, Chevy and GMC 1/2 ton and 3/4 ton Suburbans and pickups kept the closed knuckle Dana 44 through the 1969 model year although there may be some late production 1969 vehicles with the open knuckle 44. The open knuckle GM Dana 44 axle has tighter turning radius compared to the previous closed knuckle axle. Disc brakes replaced drum brakes effective with the 1971 model year.

Axle Shafts

top_page
product note

GM used at least three different axle shaft configurations for 1969-1972 Dana 44 front axles. 1969 Blazer inner axle shafts are 1" shorter than 1970-1972 axles. The outer axle shaft for 1969-1970 drum brake axles are 1/10" shorter than those used on 1971-1972 disc brake axles. In mid-year 1972, the axle u-joint size was increased from 1310WJ series (1-1/16" cups) to 1350WJ series (1-3/16" cups) although the lengths remained the same. Also during the 1972 model year, the spindle to axle seal was first changed from a 2" ID conventional seal to a 2" ID rubber V-Seal. Late in the year, the outer axle shaft changed again when the spindle seal ID was increased from 2" to 2-1/4".

photo

QU40670 1969-1970 GM Dana 44 Outer Axle Shaft Is genuine original equipment Dana outer axle shaft for all Dana 44 drum brake equipped front axles in 1969, 1970 Blazers and all 1970 GMC Jimmys, plus K10/K15/K1500 1/2 ton and K20/K25/K2500 3/4 ton 4x4 Suburbans and trucks. Use with QU40324 2" OD Outer Axle Shaft Slinger.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40669 1971 and partial 1972 GM Dana 44 Outer Axle Shaft for Small U-Joint Is genuine original equipment Dana outer axle shaft for Dana 44 front axles with disc brakes in all 1971 and many 1972 Chevy Blazers, GMC Jimmys, plus K10/K15/K1500 1/2 ton and K120/K25/K2500 3/4 ton 4x4 Suburbans and trucks. Axle u-joint cup diameter is 1-1/16". Use with QU40324 2" OD Outer Axle Shaft Slinger.
Link to Our QU40669 Large Text Catalog Web Page
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40221 Late 1972 GM Dana 44 Outer Axle Shaft for Large U-Joint Is genuine original equipment Dana outer axle shaft for those 1972 Dana 44 front axles with axle u-joints that have a cup dimater of 1-3/16". These axles would be in those 1972 Chevy Blazers, GMC Jimmys, plus K10/K15/K1500 1/2 ton and K120/K25/K2500 3/4 ton 4x4 Suburbans and trucks that have Spicer 1350WJ series axle u-joints. QU40221 Outer Axle takes QU40058 2-1/4" OD Axle Slinger.
Link to Our QU40221 Large Text Catalog Web Page
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40637 1972.5 30 Spline Right Inner Axle Shaft for Chevy, GMC Dana 44 Front Axles with Large U-Joint Is a genuine original equipment Dana Right Inner axle shaft for mid to late production 1972 Chevy Blazers, GMC Jimmys, plus Chevy, GMC 4x4 1/2 ton or 3/4 ton Pickups and Suburbans with axle universal that have a cup diameter of 1-3/16". Dan the Gear Man Tech Note: You can upgrade your 1971 to 1972.5 axle to to these 1350WJ series axle shafts.
Link to Our QU40637 Large Text Catalog Web Page
Also available while supplies last: QU40637U
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40638 30 Spline Left Inner Axle Shaft for 1973 to 1980 Chevy, GMC Dana 44 Front Axles Is a genuine original equipment Dana Left Inner axle shaft for all Dana 44 front axles in 1973 to 1980 Chevy Blazers, GMC Jimmys, plus Chevy, GMC 4x4 1/2 ton or 3/4 ton Pickups and Suburbans.
Link to Our QU40638 Large Text Catalog Web Page
Also available while supplies last: QU40638U
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK42104 High-Performance 19 Spline Outer Axle Shaft for 1969-1981 GM Dana 44 front axles. USA Made thru-hardened. 19 Spline.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK42105 High-Performance Left Inner Axle Shaft for 1969-1981 GM Dana 44 front axles. USA made thru-hardened. 30 Spline.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK42106 High-Performance Right Inner Axle Shaft for 1969-1981 GM Dana 44 front axles. USA made thru-hardened. 30 Spline.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Seals, Seal Kits, and Slingers for the INNER Axle Shaft

top_page
product note

GM used both one piece and two piece Inner Axle Shaft Oil Seals in 1969-1970 Open Knuckle Dana 44 front axles. Dimensionally, the two types are interchangeable. All 1971 and 1972 axles were built with the one piece seal that combines the Seal and Guide into a single unit. I always replace the two piece Seal with the one piece as I believe it has greater sealing ability plus longer life. With a closed knuckle axle, seal seepage from the differential often goes unnoticed until the a catastrophic ring and pinion failure occurs because the errant lube ends up in the knuckle ball. These Seals are tricky to install so I recommend you also order our optional installation tooling. Axle disassembly including differential removal is required to replace the Seals

photo
QU40055 Ford Dana 44 Unitized Inner Axle Shaft Oil Seal With integral axle shaft guide for most 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles. One of these Seals are installed in each axle tube, right next to the differential to keep differential gear lube from leaking into the closed knuckle balls
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4871 Dana 44 Axle Seal Kit with Fixed Depth Axle Seal Tool Set Quickly and easily installs QU40055 Inner Axle Seals to a precise depth in most 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles. Our unique installer design will press in new your Inner Axle Seals to the exact depth and without damage because the CNC Precision Machined Installation Tool cups the seal so force is only applied on the steel seal shell
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40159 One Piece seal for 1970 K20 Trucks with axle Bill of Material Number 603036 is the original equipment replacement Seal
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40460 Dana 44 Front Inner Axle Shaft Slinger Is stamped steel Axle Shaft Slinger that fits on your inner axle shaft next to the u-joint yoke. The function of this Slinger is to deflect crud away from entering the axle housing tubes.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note
General Motors used an small Spicer 1310WJ series axle universal joint with tiny 1-1/16" diameter u-joint cups for the 1969 to 1972.5 Dana 44 open knuckle front axles. The physical dimensions of this series of axle joint means is marginal for full size truck applications which is why it was replaced by Spicer 1350WJ series medium size axle u-joints with 1-3/16" cups during the 1972 model year. Always verify your axle u-joint cup dimeter before ordering replacement u-joints
photo
QU40792 1969-1972.5 Chevy, GMC Dana 44 Factory-Lubed 1310WJ Front Axle Shaft U-Joint Is a hot-forged, original equipment, non-greaseable, front axle shaft universal joint with 1-1/16" diameter cups. This is the strongest production u-joint we know of for 1969-1972.5 Chevy and GMC Blazer, Jimmy, Suburban and truck 4x4s with Spicer 1310WJ series axle u-joints with 1-1/16" diamter cups
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40822 1969-1972.5 Greaseable 1310WJ Axle U-Joint with 1-1/16" cups for 1969-1972.5 GM Dana 44 open knuckle front axles in 4x4 Blazer, Jimmy, Suburban and truck. QU40822 has a hot-forged cross and it has one cap drilled and tapped for a flush mount grease fitting for ease of lubrication
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK40712 1972.5 Torque King® Premium Non-Greaseable 1350WJ Axle U-Joint for Chevy, GMC Dana 44 Front Axles Fits late production 1972 4x4 Blazer, Jimmy, Suburban and truck axle shafts with u-joint cups that measure 1-3/16" in diameter. TK40712 is our strongest, highest quality universal joint for this application and it features a premium Cold-Forged cross and superior pressure-type seals
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90007 1972.5 Greaseable Axle 1350WJ U-Joint with Rubber Seals For late production Chevy and GMC Dana 44 Front Axles in 4x4 Blazer, Jimmy, Suburban or truck. Value priced with has a hot-forged cross and it has one cap drilled and tapped for a flush mount grease fitting for ease of lubrication
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ball Joints

top_page
product note
The 1969-1972 GM Dana 44 Beam Type open knuckle front axle uses replaceable Ball Joints pressed into the steering knuckle. Both Ball Joints are weight bearing. A threaded adjuster that screws into the upper hole of the axle yoke is used to provide preload on the Ball Joints. Dana has modified the seal configuration on the current production parts, but the high quality and basic Ball Joint design has remained unchanged since the early 1970's. Over the years we have found the average Ball Joint life of our non-greaseable, factory Dana Ball Joints to be 7 to 10 years for vehicles used as daily drivers and/or work vehicles
photo
QU40187 Original Equipment Ball Joint Set for 4x4 Bolt Front Axles Are the current production original equipment, factory lubed, Upper and Lower Ball Joints with hardware for 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
product note
All 1971-1972 GM Dana 44 disc brake front axles used the same disc brake pads. The Caliper Support Plate/Brake Shield assemblies will vary by both year and model. For the Caliper Support Plate/Brake Shield assemblies, 1/2 ton and 3/4 ton parts are always different as the 3/4 ton trucks have a larger diameter rotor. For a given year and model, both left and right Caliper Support Plate/Brake Shields assemblies are the same on both sides of your axle
QU30213U Used 1/2 Ton Caliper Support and Brake Shield For 1971-1972 Chevy and GMC 1/2 tons, Blazers, and Jimmy is a serviceable used part for your vintage GM 4x4 with disc brakes and 6 bolt wheels. Shield has hole for 1/4" bolt. Bolt hole is equidistant from adjacent spindle bolt holes so part will fit either left or right side
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings (Individual)

top_page
product note
All 1969 to 1972 Chevy K10/K20 and GMC K15/K25 4x4 trucks with open knuckle Dana 44 Front Axles use the same differential and pinion bearings.
All bearings are not created equal for fit or durability, so we only stock first class, long lasting, Timken® Differential and Pinion Bearings for your Dana front axle. Timken® was and is a a major original equipment supplier of top-notch bearing components to Dana Spicer. Since I first started rebuilding Dana axles in the mid 1970's, I have found Timken® Bearings to be the most consistent in relation to the published dimensions of any bearing on the market which makes rebuilding an axle right the first time a WHOLE lot easier!
photo
QU50533 Timken® Outer Pinion Bearing Cup For 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50534 Timken® Outer Pinion Bearing For 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50535 Timken® Inner Pinion Bearing Cup For 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50536 Timken® Inner Pinion Bearing For 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50538 Timken® Differential Side Bearing For 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles. (uses 2)
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50537 Timken® Differential Side Bearing Cup For 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles. (uses 2)
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU30170U Loaded Differential Case For Dana 44 with 3.92 to 5.89 ratio gear sets and 30 spline axle shafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40632 Empty Differential Case Kit For Dana Model 44 3.73 and numerically lower ratios. Includes ring gear bolts and diff shims
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40633 Loaded Differential Case Assembly For Dana Model 44 3.73 and numerically lower ratios. Includes spider gears, diff bearings, ring gear bolts and diff shims
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40634 Empty Differential Case Kit For Dana Model 44 3.92 and numerically higher ratios. Includes ring gear bolts and diff shims
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40635 Loaded Differential Case Assembly For Dana Model 44 3.92 and numerically higher ratios. Includes spider gears, diff bearings, ring gear bolts, and diff shims
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing and Seal Kits

top_page
product note
1969-1972 Chevy Blazers and all 1970-1972 GMC Jimmy and Chevy/GMC 1/2 ton and 3/4 ton 4x4 trucks have open knuckle Dana 44 Front Axles. If your vintage GM 4x4 has over 150, 000 miles on it, there is a good chance that significant bearing wear may have occurred on your differential and pinion bearings. When you replace the bearings, do not forget to replace the inner axle shaft oil seals.
photo
QU50576 Differential Bearing and Seal Kit For 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/15/K25 4x4 trucks with Dana 44 open knuckle front axles features first class Timken® Differential and Pinion Bearings, Pinion Seal, Pinion Nut, Crush Sleeve, Gear Marking Compound, Threadlocker, and RTV Sealant
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
product note
Most 1969-1972 Chevy and GMC open knuckle Dana 44 Front Axles were factory equipped with conventional open differentials. Depending upon the year, optional Powr-Lok® or Trac-Lok® Differential were also available. With the open differentials, internal wear is not a huge problem, but wear on the thrust washers and cross shaft can be expected on higher mileage vehicles. The differential small parts are the same for all ratios, but the ring gear flange on the case castings are different for 3.73 and numerically lower ratios and axles having 4.09 and numerically higher ratios due to the pinion gear diameter size for high and low ratios
photo
QU40000 Dana 44 Pinion Mate Thrust Washer Is a genuine Dana hardened concave thrust washer that fits between each of the small diameter pinion mate gears in your 1969-1972 Chevy or GMC Dana 44 open differential
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40033 Dana 44 Side Gear Thrust Washer Is a genuine Dana hardened flat thrust washer that fits between each of the splined differential side gears in your 1969-1972 Chevy or GMC Dana 44 open differential
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40001 Dana 44 Differential Cross Shaft Retaining Pin Is a genuine Dana spring steel Pin used to retain your differential cross shaft in the diff case for 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40003 Dana 44 Differential Cross Shaft Is a genuine Dana hardened steel shaft that acts as the axle for the two small pinion mate gears for all 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU30170U Loaded Differential Case For Dana 44 with 3.92 to 5.89 ratio gear sets and 30 spline axle shafts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40632 Empty Differential Case Kit For Dana Model 44 3.73 and numerically lower ratios. Includes ring gear bolts and diff shims
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40633 Loaded Differential Case Assembly For Dana Model 44 3.73 and numerically lower ratios. Includes spider gears, diff bearings, ring gear bolts and diff shims
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40634 Empty Differential Case Kit For Dana Model 44 3.92 and numerically higher ratios. Includes ring gear bolts and diff shims
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40635 Loaded Differential Case Assembly For Dana Model 44 3.92 and numerically higher ratios. Includes spider gears, diff bearings, ring gear bolts, and diff shims
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Makers

top_page
product note
In the mid 1970's Dana made a differential cover design change to heavy gauge covers with flat mating flanges. Unlike the previous, thin gauge covers with embossed flanges which were made for use with a cut gasket, the new design, thick gauge covers are designed for sealing with RTV. If you desire, you can still use a gasket with the new type cover by combining the gasket with thin films of RTV. We stock both Ultra Gray RTV Sealant and genuine Dana Gaskets
photo
TK40573 Torque King® 6 Bolt Front Hub Gasket Is a brand new, precision cut, high-tech hub gasket for 1970-1972 Chevy K20, GMC K25 3/4 ton 4x4 truck with a Open Knuckle Dana 44 Axle having 6 Bolt external mount lockout hubs
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40395 Special Inner Metal Hub Gasket For all 1970-1972 Chevy K20, GMC K25 3/4 ton 4x4 trucks with a Open Knuckle Dana 44 Axle equipped with the factory Spicer Plastic Dial Locking Hubs. This gasket is located between the wheel hub and QU40547 splined hub body
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU42028 Hipro Dana 44 Cover Gasket Is a reusaeable Dana 44 High Performance Differential Cover Gasket and genuine dana part for all Dana-Spicer Model 44 axles.
See our QU42028 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40214 Dana 44 Cover Gasket Is a genuine original equipment Dana Gasket for all Dana-Spicer Model 44 axles.
See our QU40214 large text individual page for more details and tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hubs and Hub Parts

top_page
product note

The wheel hub used on 1969-1972 GM 1/2 ton 4x4s with Dana 44 open knuckle front axles has internal splines All the 1969-1972 3/4 ton 4x4s use bolt on type hubs. The drum brake and disc brake wheel hubs are not interchangeable.

photo
QU30188U 1971-1972 6 Bolt Disc Brake Front Wheel Hub Is a good used splined front wheel hub for all 1971-1972 1977 Blazer, Jimmy, Suburban, K10, and K15 1/2 ton Chevy or GMC 4x4s. Inner bearing cup bore is 3-1/8"
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU30163U Used Hub and Rotor Assembly For 1971-1972 Chevy and GMC K20/K25 3/4 ton trucks with Dana 44 disc brake front axles. These good used assemblies have good bearing bores and rotors that are above the legal minimum thickness. Order QU50101 Wheel Seal, QU50569 Inner Bearing, QU50568 Inner Cup, QU50447 Outer Cup, and QU50448 Outer Bearing separately
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40044 Hub Dial O-Ring For Dana original equipment, plastic dial, spline mount factory hubs used on 1969 to 1972 Chevy Blazer, K10, K15, and GMC Jimmy, Dana 44 front axles with internally splined wheel hubs
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40699 Large Hub Plate to Wheel Hub Internal Snap Ring For Dana original equipment, plastic dial, spline mount factory hubs used on 1969 to 1972 Chevy Blazer, K10, K15, and GMC Jimmy, 1/2 tons with Dana 44 front axles with internally splined wheel hubs.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU51181 Warn 20990 Premium Hub Set for Dana 44 Front Axles With internally splined front wheel hubs. Reliable and good looking. QU51181 Fits 1970-1972 Chevy and GMC 1/2 tons with Dana 44 front axles with internally splined wheel hubs.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU56018 Warn Manual Hub Set Is a relable, original equipment quality hub set with installation hardware for all part time transfer case equipped 1969 to 1972 Chevy Blazer, K10, K15, GMC Jimmy, 1/2 tons with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU56019 1 Side Warn Manual Hub Set
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4918 Hub Service Kit For QU56018 Warn Manual Hub Set
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50818 Warn Premium Quality 6 Bolt External Mount Hub Set For 1969-1972 Chevy and GMC 3/4 Ton 4x4s with Dana 44 front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40548 M31E Warn Lock-O-Matic Hub Set Looking for the ultimate Lock Out Hub set for your restored 1960's to mid 1970's 3/4 or 1 ton gem? Tough Warn Lock-O-Matic Hubs give you the option of automatic engagement/disengagement AND the ability to manually engage the hubs for compression braking and continuous 4 wheeling
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK30198 Gold Torque King® Heavy-Duty Anodized Aluminum Replacement Hub Dial for 1970-1972 Chevy K20 and GMC K25 3/4 ton trucks with the big Dana 6 Bolt factory installed, external mount hubs. Sold individually.
More Info

Also See TK42053 Blue Torque King® Heavy-Duty Anodized Aluminum Replacement Hub Dial

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40471 Hub Dial Sealing Ring Is a V-Seal type sealing ring that fits TK30198 Hub Dial. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20112 Spicer Hub Dial Snap Ring Secures QU40256 Hub Dial in QU40546 Chrome Cap
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40918 Hub Dial Actuating Cam Pin For Dana factory 3/4 ton QU40256 plastic dial lockout hubs
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40406 Spicer Hub Cam for external mount hubs fits early to mid 1970's GM 3/4 ton trucks with Dana model 44 front axles and factory installed, Dana-Spicer external mount (6 3/8" bolts) hubs. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20253 Hub Cam Lock Ring For QU40406 Hub Cam is a genuine replacement part for the big Dana-Spicer 6 Bolt factory installed, external mount hubs. Holds the QU40406 Hub Cam in the QU20114 Hub Clutch Gear.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU20109 Spicer Hub Axle Shaft Drive Gear Is a genuine replacement part for the big Dana-Spicer 6 Bolt factory installed, external mount hubs. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20114 Spicer Hub Clutch Gear Is a genuine replacement part for the big Dana-Spicer 6 Bolt factory installed, external mount hubs
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40032 Axle Shaft Snap Ring Is a genuine original equipment replacement Snap Ring for GM/Chevy Dana 44 front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40546 Spicer Hub Outer Chrome Cap For the big Dana-Spicer 6 Bolt factory installed, external mount hubs
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40547 Spicer Splined Hub Body For the big Dana-Spicer 6 Bolt factory installed, external mount hubs
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40257 Dana Spicer Hub Bolt For Spicer external mount original equipment plastic dial hubs are genuine original equipment replacement socket head bolts. 3/8"-16 thread
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40231 Spicer Hub Sealing Washer Is both a lockwasher and sealing washer
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50160 Small Selectro Hub Cam Fits popular aftermarket replacement Selectro and Dualmatic Classic series hubs with big cast iron dials that were widely sold in the late 1970 and 1980s to replace malfunctioning OEM hubs. This 2-5/8" OD plastic cam is a genuine replacement part for the original failure prone, cast aluminum hub cams most of these hubs were built with
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40602 Hub Bushing For the big Dana-Spicer 6 Bolt with Spicer plastic dial external mount lockout hubs
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40595 Hub Spring For Spicer OEM plastic dial external mount lockout hubs
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40427 Dana 44 Full Time Front End Hub Cap for 1968-1972 GM Dana 44 front axles. These chromed steel Caps are the redesigned cap that was introduced around 1980 and it is the recommended replacement for the 1973-1979 cap that was made from a little heavier gauge of steel. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40614 Inverted Lug Outer Axle Shaft Snap Ring Is a genuine original equipment Dana part for 1970's Chevy 4x4s with 19 Spline Outer Axle Shafts. One of these snap rings is used on each outer axle shaft
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40035 Hub Spring Plate Fits between the QU40050 hub spring and the outer wheel bearing cup on SUV's, and pickups with Model 44 front drive axles equipped with internal mount, Spicer lock out hubs or full time drive gears. These Spring Plates were used on most of the late 1960's to mid 1980's Chevy 4x4s with internal splined front wheel hubs. Made in U.S.A
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40050 Spicer Tapered Hub Spring For SUV's, and pickups with Dana Spicer Model 44 front drive axles equipped with internal mount, Spicer lock out hubs or full time drive gears. These springs were used on most of the late 1960's to mid 1980's Chevy 4x4s with internal splined front wheel hubs. Made in U.S.A. LIMITED SUPPLY
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40598 1-1/4" Wide Stepped Gear was the original design. Outside spline that engages wheel hub is 27/32" wide. These gears are stepped on the outboard side to aid in removal and to space the gear back from the hub cap. QU40598 gears were usually used with QU40050 Spring and QU40035 Spring Plate. The back edge of the snap ring groove is approximately 5/16" from the end.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40428U Used 7/8" Wide Single Width Gear Has full length ID and OD splines. These gears have 2 to 10 holes in them to reduce the weight and provide a way to remove them with a hook. QU40428 gears were generally used with QU40050 Spring and QU40035 Spring Plate in the 1970s or QU40654 1-1/4" long Split Steel Steel Spacer in the 1980s and 1990s. To use this gear, your axle shaft has to have the back edge of a snap ring groove located about 5/8" from the end.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40657U Used 7/8" Wide Stepped Gear was the most common type from the the late 1970's to the late 1980s. Outside spline that engages wheel hub is a little under 5/8" wide. These gears are stepped on the outboard side to aid in removal and to space the gear back from the hub cap. QU40657 gears were usually used with QU40050 Spring and QU40035 Spring Plate in the 1970s or QU40654 1-1/4" long Split Steel Steel Spacer in the 1980s and 1990s.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals and Technical Information

top_page
product note

Dan the Gear Man® Product Note: Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations.

photo

TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles Covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TMC71CD 1971 Chevy Truck Factory Shop Manual on CD

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TMC72CD 1972 Chevy Truck Factory Shop Manual on CD

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts

top_page
photo
QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals and Pinion Yokes

top_page
photo
QU40215 Dana 44 Front Axle Pinion Seal Is a genuine original equipment pinion seal for all 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
QU40177 Genuine Dana 4.09 Ring and Pinion Kit With pinion bearings, pinion seal, and small parts for standard Dana 44 axles. Use with 26 spline pinion yoke
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
QU40447 Genuine Dana 3.54 Ring and Pinion Kit With pinion bearings and small parts for Dana 44
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note
Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else
photo
QU40209 Dana 44 Ring Gear Bolt For Dana 44 Axles. Genuine Dana-Spicer Grade 9 Bolt has locking teeth under the hex head to prevent loosening under any load conditions.

Dan the Gear Man® Safety Note: Ring Gear Bolts are designed for a single use. They must be replaced after they are removed!

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40343 Dana 44 Hardened Differential Cap Retaining Bolt Genuine original equipment hex-head bolt for Dana Spicer Model 44 front axle differential bearing caps fits all 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40028 Dana 44 Inner Pinion Bearing Slinger Is a genuine Dana original equipment Oil Slinger. QU40028 fits between your Dana 44 axle's inner pinion bearing and pinion head
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40448 Dana 44 Inner Pinion Bearing Oil Baffle Is a genuine Dana original equipment stepped, stamped steel Oil Baffle. QU40448 fits between your Dana 44 axle's inner pinion bearing cup and the axle housing on 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40002 Outer Pinion Bearing Slinger QU40002 is a genuine Dana-Spicer part that fits between the outer pinion bearing and pinion yoke on 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40311 Dana 44 Front Differential and Pinion Shim Kit For 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles. Genuine Dana-Spicer Shim Kit includes pinion depth shims, pinion preload shims, differential adjusting shims, pinion nut, pinion washer, and differential cover pan gasket
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40009 Dana 44 Axle Pinion Lock Nut Is a genuine Dana-Spicer original equipment replacement locking nut that fits 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40010 Dana 44 Axle Pinion Washer Is a genuine Dana-Spicer flat washer that fits between the pinion nut and pinion yoke on 1969-1972 Chevy Chevy Blazer/K10/K20 and GMC Jimmy/K15/K25 4x4 trucks with Dana 44 open knuckle front axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindles and Spindle Nuts

top_page
product note

All 1969-1972 GM Dana 44 front axles had round, four slot spindle nuts from the factory. These parts can typically be reused, but you MUST always check the pin in the Inner Nut. IF the pin is damaged or broken, REPLACE THE NUT!!!

photo
QU40004 Inner Spindle Nut For 1968-1972 4x4 Chevy and GMC Blazer, Jimmy, 1/2 ton, and 3/4 ton Dana 44 Front Axle threads on the spindle and fits against your outer wheel bearing to provide correct wheel bearing end-play.
Link to Our QU40004 Large Text Catalog page for more info & tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40060 Spindle Lock Washer For 1968-1972 4x4 Chevy and GMC Blazer, Jimmy, 1/2 ton, and 3/4 ton Dana 44 Front Axle locks your QU40004 Inner Spindle Nut in position when properly installed.
Link to Our QU40060 Large Text Catalog page for more info & tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40031 Outer Spindle Nut For 1968-1972 4x4 Chevy and GMC Blazer, Jimmy, 1/2 ton, and 3/4 ton Dana 44 Front Axle is tightened against your QU40060 Spindle Lock Washer to keep it in place and it acts as a jam nut effectively locking both spindle nuts and the washer together.
Link to Our QU40031 Large Text Catalog page for more info & tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4727 Spindle Nut Kit For 1968-1972 4x4 Chevy and GMC Blazer, Jimmy, 1/2 ton, and 3/4 ton Dana 44 includes one each of QU40004 Inner Spindle Nut, QU40060 Spindle Lock Washer, and QU40031 Outer Spindle Nut.
Link to Our QK4727 Large Text Catalog page for more info & tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40630 1970 1/2 ton Open Knuckle Spindle For Dana 44 open knuckle front axles with front drum brakes in 1969.5-1971 GM 1/2 ton 4x4s.
Link to Our QU40630 Large Text Catalog page for more info & tech notes
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40593GM/QU40683U/Y440593GM 1971-1972 1/2 ton Dana 44 Bolt Front Spindle for Chevy, GMC full-size 4x4s for Chevy K5 Blazer, K10 and GMC Jimmy, K15 4x4s. New Spindle Kits include installed Spindle Needle Bearing and late 1972 type V-Seals. More Info

photo

QU40323GM/QU40323U/Y440323GM 1971-1972 3/4 ton Dana 44 Bolt Front Spindle for Chevy, GMC full size 4x4s for Chevy K20 and GMC K25 4x4s with external type front wheel hubs. New Spindles include late type V-Seals and installed Spindle Needle Bearing for 1973-1977 axles. To fit your 1971-1972 axle with 2" diameter outer axle shaft slinger, you MUST replace the V-Seals with QU40043 one-piece spindle seal and replace the plastic thrust washer with QU40232 bronze thrust washer. More Info

Spindle Bearings and Seals

top_page
product note

Except for mid to late 1972 production axles which use one of two sizes of a rubber V-Seal, all 1969 to 1972 GM Dana 44 axles had a steel case grease seal pressed in the back side of the spindle. Neither seal design is water-tight, so you should clean and regrease your spindle bearings every two to three years or after immersion in water. Owners of 1972 axles with axle universal joints that measure 1-3/16" need to verify the outside diameter of their outer axle shaft slinger before ordering parts

photo

QU40043 1969-1972.5 2" ID Dana Front Axle Spindle to Axle Shaft Seal Fits 1968-early 1972 Chevy and GMC Dana 44Front Axles with 2" outside diameter axle shaft slingers. This one piece Seal gets pressed into the back of your spindle and it was used on 1969-1972 4x4's with outer axle shafts with QU40324 2" OD Outer Axle Shaft Slinger. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20040 mid 1972 Dana 44 Open Knuckle 2" ID Spindle V-Seal Fits those mid-production 1972 axles originally equipped with a 2" ID Rubber V-Seal and QU40324 2" OD Outer Axle Shaft Slinger. Note: QU20040 can be replaced by QU40043
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40324 1969-1972.5 2" OD Outer Axle Shaft Slinger Is a genuine original equipment New Old Stock (NOS) steel flinger or slinger for 1969-1972 Chevy and GMC 4x4's with open knuckle front axles Diameter of seal surface is 2"
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4734 1969-1972 Front Axle Shaft Spindle Bearing Set Fits all 1969-1972 Chevy and GMC Dana 44 front open knuckle axles. One bearing is pressed into each spindle to support the outer axle shaft
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40232 1969-1972.5 Type Brass Axle Shaft Thrust Washer Measure just under 1.875" outside diameter. This thrust washer was used on 1969-1972 Chevy and GMC Dana 44 open knuckle front axles and QU40324 2" OD Outer Axle Shaft Slinger
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40070 Late 1972 Axle Shaft to Spindle Thrust Washer Is a genuine original equipment plastic thrust washer that controls axial thrust between your outer axle shaft and spindle. Fits late production 1972 4x4 Blazer, Jimmy, Suburban and truck that have outer axle shafts with QU40058 2-1/4" OD Axle Slinger
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40071 Late 1972 2-1/4" ID Axle Shaft to Spindle V-Seal Is a genuine original equipment 2.25" ID Rubber V-Seal that seals between your axle shaft and spindle. Fits late production 1972 4x4 Blazer, Jimmy, Suburban and truck that have outer axle shafts with QU40058 2-1/4" OD Axle Slinger
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40228 Late 1972 Spindle Bearing and Seal Kit Services one side on your late production 1972 4x4 Blazer, Jimmy, Suburban and truck that have outer axle shafts with QU40058 2-1/4" OD Axle Slinger. Dan the Gear Man TECH NOTE: QU40056 small V-Seals which are included in this Kit CAN NOT be used in original 1972 spindles as the spindle bearing bore is not machined deep enough for both the spindle bearing and seal. However, if you have a replacement spindle made to the 1973 to 1977.5 specs, you can use both the bearing and seal.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40058 Late 1972 2-1/4" OD Outer Axle Shaft Slinger Acts both as a crud deflector and a sealing surface on open knuckle axles. Replace anytime they are dinged, bent or badly corroded. Fits late production 1972 4x4 Blazer, Jimmy, Suburban and truck that use a 2-1/4" OD Slinger
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Knuckles and Knuckle Bolts

top_page
photo
QU50750 1970-1972 GM Dana 44 Front Spindle to Knuckle Bolt Is a genuine original equipment Dana Knuckle Bolt that fits all 1970-1972 Chevy/GMC K10, K15, Blazer, and Jimmy Dana 44 front axles with drum or disc brakes. Serrated shank resists spinning when removing or installing the spindle retaining nut
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Linkage Parts

top_page
product note
1970-1972 GM Dana 44 front axles use a short, non-adjustable drag link that couples the steering gear pitman arm to the axle steering arm bolted to the top of the left knuckle. A long, adjustable tie rod attaches to the integral knuckle steering arms. The non-adjustable drag link can be replaced by the adjustable type found on 1973 and later trucks
photo
QU30168U Removable Left Side Steering Arm For all 1970-1972 Chevy and GMC K5 Blazer/Jimmy, K10/15, and K20/25 Suburbans and trucks with Dana 44 4x4 front axles. This steering arm which mounts on top of your left knuckle attaches to the drag link.

Link to Our QU30168U Large Text Catalog Web Page
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 44 front axle in your 1969-1972 Chevy & GM 4x4.

photo

QT5500 Wheel Bearing Packer Takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your Chevy or GM 4x4!

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1802 Bearing Cup Installer for Outer Wheel Bearing Cup For all 1969-1972 Chevy Blazer, GMC Jimmy, 1/2 ton and 3/4 ton K-Series 4x4s with Dana 44 Front Drive Axles.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1803 Bearing Cup Installer for Inner Wheel Bearing Cup For 1969-1972 Chevy Blazer, GMC Jimmy, K10, K15 Series 4x4s.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1805 Bearing Cup Installer for Inner Wheel Bearing Cup For 1969-1972 Chev, K20, K25 Series 4x4s.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1504 Front Wheel Seal Installer Specifically designed to install QU50091 and QU50654 inner wheel grease seals to the correct depth without damaging the seal. A relief groove in the installer allows adequate clearance for the outer seal lip on QU50091, thereby preventing one of the most common causes of premature seal failure.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals (Individual)

top_page
product note
All 1969 to 1972 GM 4x4 SUVs and pickups use the same outer wheel bearings. Inner wheel bearings for 1/2 ton and 3/4 ton models are different. One Wheel Seal number covers all 3/4 ton trucks, but there are two wheel seal possibilities for the 1/2 tons with the change occurring in the 1972 model year. The 1971 and prior Seal is a simple, single lip grease seal that is 1/4" wide. The 1972 Seal is 1/8" wider and it has a spring loaded double lip. The inside and outside diameters of both seals are virtually the same, but hub seal bore depth and offset differences makes it inadvisable to replace early, narrow QU50654 seal with QU50091 late seal except on 1971 models with disc brakes
photo
QU50654 1969-1971 1/2 Ton Inner Wheel Seal for GM Dana 44 with Internal Spline Wheel Hub Fits all 1969 to 1971 4x4 Chevy Blazers, K10 Suburbans, and K10 Pickups. Also fits 1969-1971 GMC Jimmy, K1500 Suburban, and K1500 truck. Seal width is 1/4".
Link to Our QU50654 Large Text Catalog page for more info & tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50091 1972 1/2 Ton Inner Wheel Seal for GM Dana 44 with Internal Spline Wheel Hub Fits 1972 4x4 Chevy Blazers, K10 Suburbans, and K10 Pickups. Also fits 1972 GMC Jimmy, K1500 Suburban, and K1500 truck. Seal width is 3/8". Can also be used as an upgrade for 1971 disc brake axles.
Link to Our QU50091 Large Text Catalog page for more info & tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50101 Premium OE Type 3/4 ton Inner Wheel Seal For all 1969-1972 Chevy and GMC K20 or K25 3/4 ton 4x4 trucks with Dana 44 open knuckle front drive axles using 6 bolt external mount lockout hubs or drive flanges. QU5050101 Premium OE Type Front Wheel Seal is interchangeable with QU50208 Flanged Front Wheel Seal.
Link to Our QU50101 Large Text Catalog page for more info & tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50208 Flanged 3/4 ton Inner Wheel Seal For all 1969-1972 Chevy and GMC K20 or K25 3/4 ton 4x4 trucks with Dana 44 open knuckle front drive axles using 6 bolt external mount lockout hubs or drive flanges. QU50208 Flanged Front Wheel Seal is interchangeable with QU50101 Premium Front Wheel Seal.
Link to Our QU50208 Large Text Catalog page for more info & tech notes
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50447 Timken® Outer Wheel Bearing Cup For all 1969-1972 Chevy Blazer, GMC Jimmy, 1/2 ton and 3/4 ton K-Series 4x4s with Dana 44 Front Drive Axles.
Link to Our QU50447 Large Text Catalog page for more info & tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50448 Timken® Outer Wheel Bearing For all 1969-1972 Chev, Blazer, GMC Jimmy, 1/2 ton and 3/4 ton K-Series 4x4s with Dana 44 Front Drive Axles.
Link to Our QU50448 Large Text Catalog page for more info & tech notes
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50577 Timken® 1/2 Ton Inner Wheel Bearing Cup for Chevy, GMC 4x4s Fits 1969-1972 Chevy Blazer, GMC Jimmy, K10, K15 Series 4x4s
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50578 Timken® 1/2 Ton Inner Wheel Bearing for Chevy, GMC 4x4s Fits 1969-1972 Chevy Blazer, GMC Jimmy, K10, K15 Series 4x4s
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50568 Timken® 3/4 Ton Inner Wheel Bearing Cup for Chevy, GMC 4x4s Fits 1969-1972 Chev, K20, K25 Series 4x4s
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50569 Timken® 3/4 Ton Inner Wheel Bearing for Chevy, GMC 4x4s Fits 1969-1972 Chevy GMC K20, K25 Series 4x4s
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
product note

It is always good preventative maintenance to replace the all wheel bearings and seals when restoring or maintaining your vintage 4x4. The parts availability for decades old 4x4s declines on a daily basis. Wrecking a wheel hub and/or spindle when the old bearing you reused fails can either cost you a mint or put your broken-down truck on blocks forever. We stock Kits with high quality Timken® Wheel Bearings and North American made Wheel Seals to keep your veteran Chevy or GMC rolling, plus, you can order your Kit with or without install tools.

photo

TK4911 1968 to 1970 GM 1/2 ton Torque King® Master Wheel Bearing Kits for Dana 44 Front Axles Fit 1969 to 1971 Chevy K5 Blazer, K10 Suburban, K10 pickup plus GMC Jimmy, K15 Suburban and K15 pickup. TK4911 Master Wheel Bearing Kit includes 4 Timken® Bearings with Bearing Cups, 2 Wheel Seals, Bearing Cup Installers, Wheel Seal Installer, and Driver Handle.

More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4912 1968 to 1970 GM 1/2 ton Torque King® Wheel Bearing and Seal Kits for Dana 44 Front Axles Fit 1969 to 1971 Chevy K5 Blazer, K10 Suburban, K10 pickup plus GMC Jimmy, K15 Suburban and K15 pickup. TK4912 Bearing and Seal Kit includes 4 Timken® Bearings with Bearing Cups, and 2 Wheel Seals.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4905 1968 to 1972 GM 1/2 ton Torque King® Wheel Bearings Only Kits for Dana 44 Front Axles Fit 1968 to 1972 Chevy K5 Blazer, K10 Suburban, K10 pickup plus GMC Jimmy, K15 Suburban and K15 pickup. TK4905 Bearing Kit includes 4 Timken® Bearings with Bearing Cups.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4714 1971 to 1972 GM 1/2 ton Torque King® Master Wheel Bearing Kits for Dana 44 Front Axles fit 1972 Chevy K5 Blazer, K10 Suburban, K10 pickup plus GMC Jimmy, K15 Suburban and K15 pickup. TK4714 Master Wheel Bearing Kit includes 4 Timken® Bearings with Bearing Cups, 2 Wheel Seals, Bearing Cup Installers, Wheel Seal Installer, and Drive Handle.

More Info

 

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4742 1971 to 1972 GM 1/2 ton Torque King® Wheel Bearing and Seal Kit for Dana 44 Front Axles fit 1972 Chevy K5 Blazer, K10 Suburban, K10 pickup plus GMC Jimmy, K15 Suburban and K15 pickup. TK4742 Bearing and Seal Kit includes 4 Timken® Bearings with Bearing Cups, and 2 Wheel Seals.

More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4708 1969 to 1972 GM 3/4 ton Torque King® Wheel Bearing and Tools Kit for Dana 44 Front Axles Are specific for 3/4 ton Chevy K20 and GMC K25 4x4 trucks with external mount lockout hubs or drive flanges. TK4708 Master Kit includes 4 Timken® Bearings with Bearing Cups, 2 Wheel Seals, Bearing Cup Installers, Wheel Seal Installer and Driver Handle.

More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4779 1969 to 1972 GM 3/4 ton Torque King® Wheel Bearing and Seal Kit for Dana 44 Front Axles Are specific for 3/4 ton Chevy K20 and GMC K25 4x4 trucks with external mount lockout hubs or drive flanges. TK4779 Bearings and Seals Kit includes 4 Timken® Bearings with Bearing Cups, plus 2 Wheel Seals.

More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK4899 1969 to 1972 GM 3/4 ton Torque King® Wheel Bearing Kit for Dana 44 Front Axles Are specific for 3/4 ton Chevy K20 and GMC K25 4x4 trucks with external mount lockout hubs or drive flanges. TK4899 Bearings Only Kit includes 4 Timken® Bearings with Bearing Cups.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!