Parts for Dana-Spicer Model 60 Front Axles in 1977-1991 Chevy & GMC 1 Ton 4x4 Trucks

We stock a complete line of parts for the open knuckle, Dana-Spicer Model 60 Front Axle which was first used by GM in the 1 ton Chevy K30 and GMC K35 4x4 trucks for the 1977 model year. The Dana 60 axle has much larger components than the Model 44 or GM 10 bolt front axles used on previous GM 4x4s. The Model 60 as used by GM from 1977 to 1991 has very durable greaseable king pins and disc brakes. The wheel bearings are serviceable and the dead-spindle configuration allows the use of lockout hubs.

When GM first introduced the 1 ton 4x4 truck in 1977,... (Continued at Bottom of Page)

Axle Identification

top_page
photo

All 1984-1991 Dana 60 and 61 Front Axles in GM 1 ton 4x4 trucks had a Bill of Material Number (BOM) stamped on a Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows) when the vehicle was shipped from the factory but, unfortunately, these tags are often missing on trucks that had prior differential service. 1977-1983 Axles will usually have the BOM number stamped on the front side of the right axle tube. The BOM number is a 6 digit number beginning with a 6 plus a dash number (ex: 610604-2). They can be used to determine not only the axle model, but also what components the axle was originally built with. We often ask for this number to insure we provide you with the exact parts you need for your truck.

Each different BOM number signifies an engineering part change which may be minor or major and may involve one or more parts. The dash number indicates the axle ratio and, for some years, the front wheel hub style (for single or dual rear wheel models).

photo

Depending on the year and engine GM Dana 60 front axles were available with 3.73, 4.10, or 4.56 gearing.

Cover: 10 Bolt, 12" high

Ring Gear: 9-7/8", 12 Bolt

Suspension: Leaf spring

Steering Linkage: 1977-1991 uses a tie rod that attaches to each steering knuckle. Drag link goes from steering gear to cast iron arm bolted to the top of the drivers side steering knuckle.

Knuckle Mounting: Greaseable King Pins. Upper uses spring loaded plastic bushing rotating on a tapered King Pin. Lower has taper roller bearing.

Wheel Hub: 1977-1991 GM Dana 60 axles have an internally splined hub in which a splined drive gear or lockout hub assembly would fit into.

 1977 Bill of Material Numbers  Model 60: 603728, 610033 
 1978 Bill of Material Numbers  Model 60: 610033
 1979-1980 Bill of Material Numbers  Model 60: 610057
 1981 Bill of Material Numbers  Model 60: 610132
 1982-1987 Bill of Material Numbers  Model 60: 610159, 610202 (1984-1985 only)
 1988-1991 Bill of Material Numbers  Model 60: 610295
 1984-1988 Military CUCV Bill of Material Number  Model 60: 610201

 

Axle Shafts

top_page
product note

We stock genuine original equipment Front Axle Shafts for 1977-1991 Chevy and GMC 1 ton trucks with Dana-Spicer Model 60 front axles. Our Brand new shafts fit all 1977-1991 civilian and military 1 ton 4x4 trucks. Use exact original equipment replacement parts for maximum strength. Note: Outer axle shafts do not come with slingers. Order QU40064 Separately. We also have custom shafts available for C3500HD heavy-duty 1 ton 4x2 dual rear wheel trucks converted to 4x4 for large fleets in the 1990s.

photo
QU40330C GM Dana 60 Outer Axle Shaft For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Order QU40064 Slinger separately.

Link to QU40330C Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40533 GM Dana 60 Right Inner Axle Shaft This short inner axle shaft is for the right or passenger side on all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with either Dana 60 front axles and single or dual rear wheels.

Link to QU40533 Large Text Catalog page for more details
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40531 GM Dana 60 Left Inner Axle Shaft This long inner axle shaft is for the left or drivers side on all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Link to QU40531 Large Text Catalog page for more details
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40623 Torque King® C3500HD 4x4 Conversion Short Side Inner Axle Shaft Is our American made heavy-duty custom chrome moly inner axle shaft for C3500HD 4x4 fleet conversions. This shaft measures about 21-1/8" from center of u-joint to end and it replaces the out of production Dana 660182-3 left inner axle shaft. THIS SHAFT DOES NOT FIT 1977-1991 1 TONS K30, K35, K3500, V3500 WITH FACTORY 4 WHEEL DRIVE!

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Shaft Inner Oil Seals and Axle Shaft Inner Oil Seal Kits

top_page
product note

An Inner Axle Seal is pressed in the inboard end of each axle tube, right next to the differential side bearings. These seals contact the inner axle shafts to prevent gear oil from running out of the differential and down the axle tubes. Old age, blown axle u-joints, and/or grit that works it's way into the axle tubes and cuts the seal are the usual causes of failure. A bad Inner Axle Shaft Seal can be detected by oil coming out the end of the axle tubes next to the axle shaft u-joint. Usually when these Seals start to fail, they will seep oil so the leakage may go undetected for quite some time. Many a ring and pinion set has been burned up from axles that lost all their lube when long term seepage was not noticed.

photo
QK4656 Adjustable Depth Type Inner Axle Shaft Seal Tool and Seal Kit For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Includes 2 QU40059 Axle Seals, QT1042 Adjustable Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate.

Please refer to QK4656 page for more details and ordering information.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4656 Adjustable Depth Type Inner Axle Shaft Seal Tool Set For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Includes QT1042 Adjustable Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate. Purchase QU40059 Axle Seals separately.

Please refer to TS4656 page for more details and ordering information.

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4867 Fixed Depth Type Inner Axle Shaft Seal Tool and Seal Kit For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Includes 2 QU40059 Axle Seals, QT1156 Fixed Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate.

Link to QK4867 Large Text Catalog page for more details
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4867 Fixed Depth Type Inner Axle Shaft Seal Tool Set For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Includes QT1156 Fixed Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate. Purchase QU40059 Axle Seals separately.

Please refer to TS4867 page for more details and ordering information
photo
QU40059 Inner Axle Shaft Seal One of these Seals are installed in each axle tube, right next to the differential to keep gear lube from leaking out the ends of the axle housing on all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Link to QU40059 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note

We offer three different Universal Joints for your hard working Chevy or GMC 1 ton Dana 60. All are plenty strong for the job, but different manufacturing techniques and seal types will have a major influence on the ultimate life of the joint. Our most popular choice is our TK40715 cold-forged, non-greaseable, original equipment replacement U-Joint. The wear-resistant cold-forged cross and superior sealing make it the best choice for both low maintenance and long life. Greaseable TK40724 U-Joints are a greaseable version of our TK40715 joints, giving you the durability advantages of cold-forging and better seals with the option to re-lube the joint at any time for unmatched longevity. QU30332 's are hot-forged and equipped with simple rubber seals. With good maintenance and quality lubricant like our Pyroplex® Plus Grease, these joints will last and last. See our individual product pages for more info.

photo
QU30332 Greaseable Axle U-Joint For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to QU30332 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK40715 Torque King® Premium Non-Greasable U-Joint For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to TK40715 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK40724 Torque King® Greasable U-Joint For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to TK40724 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

TK42117 Greaseable and Rebuildable CTM 1480WJ Series Performance Axle U-Joint for GM Dana 60 Beam Type Front Axles.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Brake Parts

top_page
product note

Brake Splash Shields deflect road splash and grit from the brake rotors. Rust from road salts or corrosive soils is the most common cause for replacement. The shields can also be bent or torn from hitting rocks off road or from accident damage. Another cause of wrecked shields is incorrect service procedures including driving a chisel between the spindle and knuckle during disassembly. We also stock some hard-to-find brake small parts.

photo
QU80005C Original Equipment Front Brake Rotor for 1977-1991 GM 1 Ton Dana 60 Front Axles Is a brand new, genuine original equipment front brake rotor for 1977-1991 Chevy and GMC K30, K35, K3500, V3500 4x4 trucks with Dana 60 front drive axles.

Link to our QU80005C Large Text Catalog Page
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU30063C Chevy, GMC Dana 60 Left Brake Splash Shield For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU30063C page for more details and ordering information
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU30062C Chevy, GMC Dana 60 Right Brake Splash Shield For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to QU30062C page for more details and ordering information
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU80004 Caliper Key and Spring Kit For all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. (We also have Oversize Caliper Key Kits to compensate for stretched or worn caliper supports.)

Please refer to QU80004 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU80000 series 0.040" to 0.160" Oversize Caliper Key and Spring Kits Help compensate for stretched brake anchor plates on 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Available in 4 sizes from 0.040" to 0.160" oversize.

Link to QU80000 Large Text Catalog page for more details
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU80003 Caliper Key Retaining Bolt Screws into the Caliper Support/Brake Anchor Plate to keep the Caliper Key from sliding out.

Please refer to QU80003 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU80015 Brake Shoe Anti-Rattle Clip Fits the lower tab of your inboard disc brake pad to keep it from rattling

Please refer to QU80015 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential & Pinion Timken Original Equipment Quality Individual Bearings

top_page
product note

Over the years, Dana has primarily used Timken bearings when building their axles. For long life and dimensional consistency, Timken bearings are unmatched by any other brand of bearing I have used rebuilding axles over the past 30+ years in the business. When you are a shade tree mechanic dealing with a diff and pinion rebearing job without all the fancy gauging tools we have, you always want your new bearings to be the same overall thickness as the original bearings were when the axle was built so your pinion depth, pinion preload and backlash are within the tolerance limits when you are done with the job. Timken bearings will almost always deliver that type of accuracy, plus the steel quality and surface finish is the world's best.

photo
QU50397 Timken® Differential Bearing Cup For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU50397 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50398 Timken® Differential Bearing For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU50398 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50400 Timken® Outer Pinion Bearing Cup For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU50400 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50401 Timken® Outer Pinion Bearing For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU50401 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50406 Timken® Inner Pinion Bearing Cup For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU50406 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50407 Timken® Inner Pinion Bearing For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Fits both single rear wheel and dual rear wheel trucks.

Please refer to QU50407 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Bearing & Seal Kits Featuring Timken® Bearings and Genuine Dana-Spicer Small Parts

top_page
product note

Torque King® Premuim Diff Bearing and Seal Kits are the #1 choice for those who depend upon their truck to keep working day in and day out no matter how tough the conditions. Our Kits combine the supurb quality of Timken bearings with the precise fit and relability of 100% genuine Dana-Spicer small parts. No aftermarket, off brand or Chinese knockoff parts in these Kits!

photo
QU40184 Dana 60 Timken® Differential Bearing Cup and Bearing Set Includes two each QU50397 Differential Bearing Cups and QU50398 Differential Bearings. Fits your 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 truck with Dana 60 front axles.

Please refer to QU40184 page for more details and ordering information
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK4864 Torque King® Premium Quality Front Differential Bearing and Seal Kit For your 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles feature 100% Timken® Bearings and genuine Dana-Spicer Small Parts. TK4864 includes: QU50400 Outer Pinion Bearing Cup, QU50401 Outer Pinion Bearing, QU50406 Inner Pinion Bearing Cup, QU50407 Inner Pinion Bearing, 2 QU50397 Differential Bearing Cups, 2 QU50398 Differential Bearings, QU40097 Pinion Seal, QU40099 Outer Pinion Slinger, QU40022 Pinion Nut, QU40023 Pinion Washer.
Please refer to TK4864 page for more details and ordering information

Also available: QU50491 Timken Bearing Kit with aftermarket small parts.

Dan the Gear Man® Product Note: TK4864 Kit does NOT include QU40059 Axle Shaft Seals. Order those separately or as part of QK4656 Axle Shaft Seal Kit
photo
TK4865 Torque King® Premium Quality Front Differential Master Service Kit For your 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks feature 100% Timken® Bearings and genuine Dana-Spicer Small Parts. TK4865 includes: QU50400 Outer Pinion Bearing Cup, QU50401 Outer Pinion Bearing, QU50406 Inner Pinion Bearing Cup, QU50407 Inner Pinion Bearing, 2 QU50397 Differential Bearing Cups, 2 QU50398 Differential Bearings, Pinion Preload Shims, QU40365 Pinion Depth Shims, QU40206 Differential Shims, 12 QU40086 Ring Gear Bolts, QU40097 Pinion Seal, QU40099 Outer Pinion Slinger, QU40022 Pinion Nut, QU40023 Pinion Washer, QU40519 Lock Pin, 2 QU40059 Axle Shaft Seals, QU90008 Gear Marking Compound, S82194 Ultra RTV Sealant, S24200 Threadlocker, and QT9404 Brush.

Please refer to TK4865 page for more details and ordering information

Dan the Gear Man® Product Note: This Kit does not include QU40041 Side Gear Thrust Washers, or QU40518 Pinion Mate Gear Thrust Washers
photo
QU50491 Differential Bearing & Seal Kit for Dana Model 60 Front Axles in 1977-1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks. This kit includes: QU50400 Outer Pinion Bearing Cup, QU50401 Outer Pinion Bearing, QU50406 Inner Pinion Bearing Cup, QU50407 Inner Pinion Bearing, 2 QU50397 Differential Bearing Cups, 2 QU50398 Differential Bearings; QU51065 early and QU50565 late, aftermarket pinion seal; QU50566 aftermarket pinion nut, QU50567 aftermarket differential and pinion shim kit; and QU90009 axle service pack. Contains USA and imported parts
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differentials and Differential Parts

top_page
product note

Differential problems with Model 60 front axles are not all that common. But Murphy, of Murphy's Law* really likes busted differentials, so when you hear that loud, heart-stopping, ominous BANG from the front axle as your 4x4 lurches to a grinding stop, you just KNOW it is one big dose of bad news. To help get you back on the road after you get rescued, we stock genuine original equipment Dana-Spicer Front Axle Differential Parts for your hard working 1 ton Chevy or GMC 4x4 truck. Except for some of the militry CUCV models, all GM Dana 60 front axles had open differentials. We do not have any CUCV limited slip differential parts.
*Murphy's Law: "Anything that can go wrong, will go wrong"

photo
QU40254 Bare Differential Case Kit Is a genuine Dana-Spicer Model 60 Case for 3.54 and 4.10 ratio ring and pinion sets. Kit includes Differential Case, 12 QU40086 Ring Gear Bolts and QU40206 Differential Shim Kit.

Please refer to QU40254 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU20271U Good Used Differential Case Dana Model 60 is a genuine Dana-Spicer part. QU20271U fits many Dana-Spicer Model 60 front or rear axles with open differentials and 4.30 or numerically lower gear ratios (ex: 3.54). Also fits some Model 61 axles.

Please refer to QU20271U page for more details and ordering information
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40331 Dana 60 Differential Inner Parts Kit Includes 2 differential side gears, 2 QU40518 pinion mate thrust washers, 2 differential pinion mate gears, 2 QU40041 side gear thrust washers, QU40520 differential cross shaft, QU40519 cross shaft retaining pin, 12 QU40086 ring gear bolts, and differential adjusting shims.

Please refer to QU40331 page for more details and ordering information
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40518 Differential Pinion Mate Thrust Washer Two of these Thrust Washers are used in each differential, one between each pinion mate gear and the differential case.

Please refer to QU40518 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40041 Differential Side Gear Thrust Washer Two of these Thrust Washers are used in each differential, one between each side gear and the differential case.

Please refer to QU40041 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40520 Differential Cross Shaft

Please refer to QU40520 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40519 Lock Pin for Differential Cross Shaft Is used to lock QU40520 differential cross shaft to the diff case.

Please refer to QU40519 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Makers

top_page
photo
QU40367 Rear Differential Cover Gasket For Model 70 Axles. These genuine Dana-Spicer gaskets will also work on your Dana 60 front axles if you wish to use a Gasket in lieu of RTV sealant. Made in U.S.A.

Please refer to QU40367 page for more details and ordering information.

Dan the Gear Man® Tech Note: RTV sealant instead of Gaskets were used during the factory assembly of your axle.

photo
S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Dodge Ram.

Please refer to S82194 page for more details and ordering information

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hub Assemblies and Hub Parts

top_page
product note

General Motors used internally splined wheel hubs for all 1977 to 1991 Dana 60 axles. Solid drive gears or both manual and automatic hub locks were supplied with civilian Dana 60 front axles depending upon the year and transfer case option. 1977-1979 Trucks with NP203 full time transfer cases had solid steel drive gears. 1979 to 1983 (and possibly 1984) models with NP205 part time transfer cases were equipped with Spicer yellow plastic dial manual hubs. The Spicer hubs were replaced by Warn hubs with black plastic dials. Two types of automatic locking hubs were used, but we have no new parts for either the 1982/1983 version or the 1984 and later type. We only stock parts for the Warn Black Plastic Dial manual hub used on factory manual hub equipped 1985 to 1991 K/V series 1 ton 4x4s. Mechanically, this is the same Warn hub as that sold by the aftermarket with a black plastic dial for the 1977-1991 model years (The factory Warn hub may also be found on some 1984 trucks with non-synchronized NP205 transfer cases).

photo
QU30139 GM Dana 60 SRW Hub and Rotor Assembly Is a New Old Stock (NOS) genuine GM Hub and Rotor assembly for Dana 60 front axles on all 1977-1991 Chevy and GMC 1 ton single Rear Wheel (SRW) 4x4 trucks.

Please refer to QU30139 page for more details and ordering information
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
TKA4962/TK4963 Torque King® 1 Ton Internal Spline Heavy-Duty Front Wheel Hubs For 1977-1991 Chevy and GMC K30, K35, K3500, V30, V35, V3500 1 ton Single Rear Wheel 4x4 Trucks TKA4962 Hub only includes the Hub with two Timken® bearing cups. TK4963 Hub Kit includes the Hub, Timken® bearings, wheel seal and 8 wheel studs
photo
QU30201U Used GM Front Dana 60 DRW Hub Is a serviceable, used, genuine GM Hub without bearing cups for the Dana 60 front axle on all 1977-1989 Chevy and GMC K30, K35, K3500, V3500 trucks with Dual Rear Wheels
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40554 Full Time Dana 60 Hub Cap Is a Dana Spicer Hub Cap for Chevy and GMC 1 ton K30, K35 trucks with full time NP203 transfer cases from 1977 to 1979.

Please refer to QU40554 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU42085U Used Full-Time Hub Gear Spacer is used to keep QU40553 splined solid steel Drive Gear from moving in the wheel hub on Chevy and GMC 1 ton K30, K35 trucks with full time NP203 transfer cases from 1977 to 1979.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40553 Full Time Dana 60 Hub Drive Gear Is a Dana Spicer splined solid steel Drive Gear for Chevy and GMC 1 ton K30, K35 trucks with full time NP203 transfer cases from 1977 to 1979.

Please refer to QU40553 page for more details and ordering information
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40549U Dana 60 Hub Dial Retainer Is a functional used Dana Spicer Lock Out Hub Cap/Dial Retainer for Chevy and GMC 1 ton K30, K35 trucks from 1977 to 1983.

Please refer to QU40549U page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40550R Dana 60 Axle Shaft Drive Gear Is a reconditioned Dana Spicer Lock Out Hub Axle Drive Gear for Chevy and GMC 1 ton K30, K35 trucks from 1977 to 1983.

Please refer to QU40550R page for more details and ordering information

photo
QU40551R Dana 60 Hub Drive Gear Is a reconditioned Dana Spicer Lock Out Hub Driven Gear for Chevy and GMC 1 ton K30, K35 trucks from 1977 to 1983.

Please refer to QU40551R page for more details and ordering information
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40552R Dana 60 Clutch Retainer Ring Is a reconditioned Dana Spicer Lock Out Hub Retaining Ring for Chevy and GMC 1 ton K30, K35 trucks from 1977 to 1983.

Please refer to QU40552R page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50116 QUAD-Ring square cross section sealing ring For Factory type Warn® Spline Mount Hubs in 1985 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to QU50116 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50240 O-Ring For Warn® Spline Mount Hub Dials in 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to QU50240 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40068 Axle Shaft Snap Ring Fits in the groove machined at the end of the outer axle shaft splines Dana Model 60 in 1985 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to QU40068 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40150 Lockout Hub to Wheel Hub Snap Ring For Factory type Warn® Spline Mount Hubs in 1985 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to QU40150 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU56025 Warn 38826 Premium Hub Set for Dana 60 Front Axles With internally splined front wheel hubs. A sharp looking and reliable hub. QU56025 Fits Chevy and GMC Dana 60 front axles 1977-1991
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU56011 Warn® Dana 50 and Dana 60 Internal Spline Mount Hub Locks For 1977 to 1991 Chevy and GMC K30/K35/K3500/V3500 Dana 60 front axles.

Please refer to QU56011 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU56013 Warn® Dial Assembly For Original Equipment Spline Mount Hubs used in Factory type Warn® Spline Mount Hubs in 1985 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to QU56013 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU56017 Warn® Spiral Retaining Ring For Current Production Spline Mount Replacement Hubs

Please refer to QU56017 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU56016 O-Ring for Warn® Current Production Spline Mount Replacement Hubs

Please refer to QU56016 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU56012 Original Equipment Warn® Hub Screw For Warn® Spline Mount Hubs in 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to QU56012 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40113 Torx® Upgrade Screw For Warn® Spline Mount Hubs in 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to QU40113 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU56015 Replacement Decals For Warn® Plastic Hub Dials for Warn® Spline Mount Hubs in 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to QU56015 page for more details and ordering information
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42038 O-Ring for the Hub Cap on Dana 60 front axles in 1977-1983 GM 4x4's with Dana 60 axles equipped with factory installed Dana plastic dial spline mount hub locks.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40153 Hub Cap Screw for Dana factory Dana 60 plastic dial, internal spline mount hubs on 1977-1983 Chevy/GMC 1 ton with Dana 60 front axles.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

King Pin Kits and King Pin Parts

top_page
product note

We stock all the normal replacement parts for Dana 60 King Pin type Front Axles. 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles use greaseable and rebuildable King Pins instead of Ball Joints to mount the steering knuckles to the axle housing. Time has proven the Dana 60 King Pin design to be the most durable front axle steering components ever installed in Class 2 3/4 ton and Class 3 one ton 4x4 trucks. Although at first glance the number of King Pin parts may appear daunting, the fact is King Pins front axle components are usually pretty easy to replace if they ever need service beyond regular greasing.

photo
QK4512 Dana Model 60 King Pin Kit for 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles. Kit includes Lower King Pin Bearing Assemblies, king pin seals, lower king pin grease retainers, upper king pin bushings, tension springs, spring plates, anti-seize, Threadlocker, disc brake lube, RTV sealant, & cotter keys for the tie rod ends Link to QK4512 Large Text Catalog page for more details
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40191 Dana 60 Lower King Pin Bearing and Seal Kit for 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles includes one each of these genuine Dana replacement parts: QU40062 Lower Grease Retainer, QU50600 Lower King Pin Bearing, QU50601 Lower King Pin Bearing Cup, QU40092 Lower King Pin Seal, QU40147 Upper King Pin Seal. Order two Kits per vehicle. Also See QK4512 King Pin Kit

Link to QU40191 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4550 Dana 60 and Dana 61 Upper King Pin and Wrench Set includes 3/4" Drive Impact Socket/Hex Bit Socket, 2 genuine Dana Spicer Upper King Pins, and S9979 High Strength Threadlocker

Link to QK4550 Large Text Catalog page for more details

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40266 Dana 60 Upper King Pin is a genuine Dana Spicer service part for your 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with a Dana 60 open knuckle, king pin front end Link to QU40266 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40157 Dana 60 Upper King Pin Spring Retainer Plate is a genuine Dana Spicer replacement part for 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles. This Retainer Plate fits between QU40265 Tension Spring and QU40093 Upper King Pin Bushing. The raised inner rim keeps the Spring centered over the bushing. Made in U.S.A. Also see QK4512 King Pin Kit

Link to QU40157 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40265 Dana 60 Upper King Pin Spring This genuine original equipment Dana Spicer heavy-duty coil spring applies constant tension to QU40093 Upper King Pin Bushing to automatically adjust for wear and dampen road shock. QU40265 fits 1975 to 1993 model years on all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 open knuckle front axles with King Pins

Link to QU40265 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40093 Dana 60 Plastic Upper King Pin Bushing This long lasting, genuine original equipment Dana Spicer split plastic bushing has a tapered ID to match QU40266 Upper King Pin. QU40093 fits 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles with King Pins. Also see QK4512 King Pin Kit

Link to QU40093 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40147 Dana 60 Upper King Pin Seal is a genuine Dana Spicer service part for all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles. Also see QK4512 and QU40191 King Pin Kits

Link to QU40147 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40063 Dana 60 Upper King Pin Gasket is a genuine Dana Spicer replacement Gasket for all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles. A high quality cut gasket that seals between your steering knuckle and upper king pin cap/steering arm. Use two QU40063 Gaskets per vehicle. Made in Indonesia. Also see QK4512 King Pin Kit

Link to QU40063 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40062 Dana 60 Lower King Pin Grease Retainer is a genuine Dana Spicer service part for al 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles

Link to QU40062 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50600 Large King Pin Bearing for Dana Heavy Duty Front Axles for all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles. Also see QK4512 and QU40191 King Pin Kits

Link to QU50600 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50601 King Pin Bearing Cup for Dana 60 and Dana 70 Front Axles for all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles. Also see QK4512 and QU40191 King Pin Kits

Link to QU50601 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40092 Dana 60 Lower King Pin Seal is a genuine Dana Spicer service part for all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles. Also see QK4512 and QU40191 King Pin Kits

Link to QU40092 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU30064 Dana 60 Upper King Pin Cap/Steering Arm Stud is a genuine original equipment replacement part for securing the drivers side steering arm to the steering knuckle on all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles

Link to QU30064 Large Text Catalog page for more details

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals, Technical Service Bulletins, and Videos

top_page
photo
TM4400P Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
VSG4506 Model 60 King Pin Service Video (Previously named QK4512DVD or V4512DVD) shows you how to perform King Pin Service on your 1975-1993 Dodge Model 60 or Model 61 open knuckle 4x4 front drive axle
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts

top_page
product note

Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings.

photo
S24200 Blue Threadlocker for pinion nuts, spindle bolts, ring gear bolts etc
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90008 Gear Marking Compound use with QT9404 Brush to check your ring and pinion gear tooth pattern

Link to QU90008 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90018 Pyroplex® Protection ES Synthetic Grease provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions!

Link to QU90018 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90016 SynPower® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles. Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints

Link to QU90016 Large Text Catalog page for more details.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90015 High Performance Synthetic Arctic Grease is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather

Link to QU90015 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90017 Red Grease is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. cartridge or 1 pound tub

Link to QU90017 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU90009 Universal Axle Service Pack is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound

Link to QU90009 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Yokes, Pinion Seals, and Pinion Yoke Parts

top_page
product note

For the entire 1977-1991 production run, GM Dana 60 front axles used pinion yokes for the small Spicer 1310 series universal joint. The universal joint is attached to the pinion yoke with u-bolts.

photo
QU40097 Chevy, GMC Dana 60 Front Axle Pinion Seal This genuine Dana-Spicer original equipment service part fits all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles

Link to QU40097 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50565 Dana 70 Aftermarket Pinion Seal for 1994-1999 Dana-Spicer Model 70 Rear Axles in Dodge Ram 2500 trucks

Link to QU50565 Large Text Individual Product Page.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40401 Chevy, GMC Dana 60 Pinion Slinger is a genuine original equipment part for all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles

Link to QU40401 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40768 Chevy, GMC Driveshaft U-Bolt Kit is used to attach your front CV driveshaft to the Dana 60 pinion yoke on all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles

Link to QU40768 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40847 Chevy, GMC Dana 60 Pinion Yoke directly replaces worn or damaged original equipment pinion yokes on all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles

Link to QU40847 Large Text Catalog page for more details

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page
product note

Unless your axle has run out of oil or it is severely abused, you will probably never have to replace your original ring and pinion set. However, if you do need one, we stock original equipment Dana-Spicer Gear Sets for your vintage Chevy/GMC Dana 60 front axle. These genuine gear sets are not cheap when compared to the host of knock off Asian import gear sets being pushed into the market place by vendors focused on getting the cheapest stuff they can. Well, like anything, you get what you pay for. I have been setting up Dana Gear Sets since the mid 1970's to date, and I have never had a setup problem with a genuine Dana-Spicer Gear Set. The same is not true for the aftermarket parts. Besides having sloppy machining, most aftermarket gears are not made to use the Dana factory set up tools, so a person usually has to apply some blood-boiling "Kentucky Windage" to the setup procedure to make progress!

photo
QU40252 Dana 60 4.10 Ratio Gear Set is a genuine Dana Spicer gearset that includes matched 4.10 ratio ring and pinion gears, Inner and Outer Pinion Bearings with Cups. 12 Ring Gear Bolts, pinion seal, Pinion Nut, Pinion Washer, Outer Pinion Slinger, Inner Pinion Slinger, Inner Pinion Baffle, Diff Cover Gasket, Pinion Depth Shims, Pinion Preload Shims, and Differential Adjusting Shims

Link to QU40252 Large Text Catalog page for more details

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

YG D60-354 High Performance Yukon Replacement Ring & Pinion Gear Set for 1971-1992 K30/K3500 and 1973-1991 G35/G3500 1 Ton 4x4 Dana 60 in a 3.54 ratio. This fast ratio gear set makes for good fuel economy. 9.75" Rear Gear Diameter, 29 Spline Pinion. Includes 12 ring gear bolts.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note

Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else.

photo
QU40064 Slinger for Outer Axle Shaft Presses on 1977 to 1991 QU40330C outer axle shafts in your Chevy or GMC K30, K35, K3500, and V3500 and acts as both the mounting surface and protective slinger for QU40065 Spindle V-Seal.

Please refer to QU40064 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40343 Dana 60 Hardened Differential Cap Retaining Bolt Genuine original equipment hex-head bolt for Dana Spicer Model 60 and 61 front axle differential bearing caps fits all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Please refer to QU40343 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40022 Dana 60 Pinion Nut Genuine original equipment pinion nut for Dana Spicer Model 60 front axle differential bearing caps fits all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. QU40022 is a genuine original equipment, self-locking nut, intended for a single use part, discard and replace with a new nut any time you remove the pinion nut.

Also included in TK4864 and TK4865

Please refer to QU40022 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40023 Dana 60 Pinion Washer For Dodge Ram is a genuine original equipment flat washer goes between the pinion nut and pinion yoke. Fits all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Also included in TK4864 and TK4865

Please refer to QU40023 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40207 Dana 60 and Dana 61 Differential and Pinion Shim Kit For Dana-Spicer Model 60 front axles in 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Genuine Dana-Spicer Shim Kit includes Pinion depth shims, pinion preload shims, differential adjusting shims, pinion nut, and cover gasket
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40206 Dana 60 Differential Bearing Shim Kit Includes a selection of genuine original equipment Shims for adjusting backlash and differential bearing preload on your 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Also included in TK4865 and QU40207

Please refer to QU40206 page for more details and ordering information.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40099 Dana 60 Outer Pinion Slinger Fits between the outer Pinion Bearing and Pinion Yoke. QU40099 is a genuine original equipment Dana Spicer part. Fits al 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.

Also included in TK4864 and TK4865

Please refer to QU40099 page for more details and ordering information.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40086 Dana 60 Ring Gear Bolt For Dana 60 front axles. Genuine Dana-Spicer Grade 9 Bolt has locking teeth under the hex head to prevent loosening under any load conditions.

Also included in TK4865

Please refer to QU40086 page for more details and ordering information.

Dan the Gear Man® Safety Note: Ring Gear Bolts are designed for a single use. They must be replaced after they are removed!

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU30064 Dana 60 Upper King Pin Cap/Steering Arm Stud is a genuine original equipment replacement part for securing the drivers side steering arm to the steering knuckle on all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles

Link to QU30064 Large Text Catalog page for more details

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindles and Spindle Nuts

top_page
product note

General Motors use the same QU40293C front spindle on all 1977 to 1991 K30, K35, K3500, and V3500 one ton 4x4 trucks with the Model 60 open knuckle front drive axle. Spindle nuts are a different story. GM used a 6 slot spindle nut set with a thrust washer and bend over tab lockwasher from 1977 to 1981. For 1982 to 1991, a round 4 slot nut double nut design was used except on 1984 trucks with factory auto hubs which had a drag nut set that is no longer available. The good news is most of those unreliable auto hubs were junked years ago, so you can use the 3 piece round nut set with manual hubs.

photo

QU40293C Chevy, GMC Dana 60 Front Spindle Kit for all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. QU40293C is a genuine Dana factory part.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Y440293C Chevy, GMC Dana 60 Front Spindle Kit for all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4728 1977-1981 Chevy, GMC Dana 60 Round, 6 Slot Spindle Nut Kit for 1977-1981 GM Dana 60 front axles. Kit includes QU40038 Inner Thrust Washer, Two QU40036 6 Slot Spindle Nuts, and QU40037 Bend Over Tab Spindle Lock Washer.
More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40036 1977-1981 Chevy, GMC Dana 60 6 Slot Spindle Nut is a genuine original equipment replacement nut for either the inner or outer front spindle nut for the Dana 60 front axle in 1977-1981 GM 1 ton 4x4 trucks. Order 2 Nuts per side. Use with QT1025 Spindle Nut Wrench.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40037 1977-1981 Chevy, GMC Dana Dana 60 Spindle Lockwasher for 6 Slot Spindle Nuts QU40037 is a genuine original equipment replacement lockwasher that fits between the inner and outer front spindle nut for the 1977-1981 era GM Dana 60 front axles.
More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40038 1977-1981 Chevy, GMC Dana Dana 60 Inner Thrust Washer for 6 Slot Spindle Nuts QU40038 is a genuine original equipment replacement Thrust Washer that goes between inner front spindle nut and outer wheel bearing on 1977-1981 GM 1 ton Dana 60 front axles.More Info

photo

QK4729 1982-1991 Chevy, GMC Round 4 Slot Spindle Nut Kit for 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.Kit includes one each QU40163, QU40164, and QU40166. Does not work on 1984 axles that still have factory auto hubs.
More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40163 1982-1991 Chevy, GMC 4 Slot Round Outer Spindle Nut for 1982 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Nut has 4 slots for QT1110 Spindle Nut Wrenches. Does not work on 1984 axles that still have factory auto hubs.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40164 1982-1991 Chevy, GMC Spindle Lock Washer for 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Does not work on 1984 axles that still have factory auto hubs.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40166 1982-1991 Chevy, GMC Round 4 Slot Inner Spindle Nut with Pin for 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. QU40166 has 4 slots for QT1110 Spindle Nut Wrench. Includes round pin that engages one of the holes in QU40164 Spindle Lock Washer. Does not work on 1984 axles that still have factory auto hubs.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU95037 Heat-treated, All Metal, Spindle to the Steering Knuckle Lock Nut Six of these USA Made, 150, 000 psi rated Locknuts fit on QU40541 Spindle to Knuckle Bolt to secure each of your QU40293C Spindles to the Steering Knuckles.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40541 Spindle-to-Knuckle Bolt Six of these press-in special bolts fit each steering knuckle. They are used along with QU95037 Locknut to retain your spindles and caliper anchor plates.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Bearings and Seals

top_page
product note

The dead spindle design of the 1975-1993 era Dodge Dana 60 series axles uses QU40149 needle bearing to support QU40330D outer axle shaft. To protect the bearing and control axial thrust, a 4 piece set consisting of QU40064 Slinger, QU40065 Large V-Seal, QU40148 Small V-Seal, and QU40066 Thrust Washer was used. We have both Kits and individual exact replacement Dana-Spicer Spindle small parts for your hard-working Dodge

photo
QU40064 1977-1991 Chevy, GMC Dana 60 Outer Axle Shaft Slinger Presses on 1977 to 1991 QU40330C outer axle shafts in your Chevy or GMC K30, K35, K3500, and V3500 and acts as both the mounting surface and protective slinger for QU40065 Spindle V-Seal.
Please refer to QU40065 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40065 1977-1991 Chevy, GMC Dana 60 Large Spindle V-Seal is a genuine Dana Spicer part that fits between the spindle and QU40064 outer axle shaft slinger in 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Link to QU40065 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40066 1977-1991 Chevy, GMC Dana 60 Outer Axle Shaft to Spindle Thrust Washer Is a genuine Dana Spicer part that fits on your Dana 60 outer axle shaft to control thrust between the axle shaft and spindle.
Please refer to QU40066 page for more details and ordering information.
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40148 1977-1991 Chevy, GMC Dana 60 Small Spindle V-Seal Is a genuine Dana Spicer part that fits in the back of your spindle between QU40149 spindle bearing and QU40066 thrust washer in Model 60 open knuckle front drive axles on your 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.
Please refer to QU40148 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40149 1977-1991 Chevy, GMC Dana 60 Spindle Bearing Is a genuine Dana Spicer original equipment part that is a press fit in the back of the spindle. This bearing is the primary support for your outer axle shaft.
Please refer to QU40149 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40168 1977-1991 Chevy, GMC Dana 60 Spindle Bearing and Seal Kit Services ONE side of your 4x4 with one each of these parts: QU40065 Large Spindle V-seal, QU40066 Spindle Thrust Washer, QU40148 Small Spindle V-seal, and QU40149 Spindle Bearing.
Please refer to QU40168 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Steering Knuckles

top_page
photo
QU30064 Dana 60 Upper King Pin Cap/Steering Arm Stud Is a genuine original equipment replacement part for securing the drivers side steering arm to the steering knuckle on all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles.
Link to QU30064 Large Text Catalog page for more details
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 60 front axle in your 1977-1991 Chevy or GMC 1 ton.

photo
QT1064 Dana 60 Upper King Pin Wrench Removes and installs the upper king pin cones on 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels.
Link to QT1064 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT5500 Wheel Bearing Packer Takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your big GM 1 ton!
Link to QT5500 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4656 Adjustable Depth Type Inner Axle Shaft Seal Tool Set For 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Includes QT1042 Adjustable Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate. Purchase QU40059 Axle Seals separately.
Link to TS4656 Large Text Catalog page for more details
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4867 Fixed Depth Type Inner Axle Shaft Seal Tool Set for 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Includes QT1156 Fixed Depth Seal Installer, QT1133 Alloy Steel Press Screw with Hardware, & QT1130 Thrust Plate. Purchase QU40059 Axle Seals separately. Link to TS4867 Large Text Catalog page for more details
photo
QT1133 Inner Axle Seal Press Screw Assembly For installing QU40059 Inner Axle Seals in 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Use with the QU1042 or QT1156 Seal Installers and QT1130 Thrust Plate Thrust Plate. Also see TS4656 and TS4867 Inner Axle Seal Installer Tool Sets.
Link to QT1133 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1042 Adjustable Depth Inner Axle Seal Installer Also see TS4656 Inner Axle Seal Installer Tool Set.
Link to QT1042 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1156 Fixed Depth Inner Axle Seal Installer Also see TS4867 Inner Axle Seal Installer Tool Set
Link to QT1156 Large Text Catalog page for more details
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1130 Thrust Plate Fits all Dana Model 60, Super 60, 61, and Closed Knuckle Model 70 axles from 1967-current. Also see TS4656 and TS4867 Inner Axle Seal Installer Tool Sets.
Link to QT1130 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TS4862 Inner Axle Seal Remover Set Is used to drive the QU40059 inner axle seals out of the axle housing bores on all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Set includes QT1145 Driver Handle, QT1151 Extension Rod, and QT1214 Seal Remover.
Link to TS4862 Large Text Catalog page for more details
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT2005 Inner Pinion Bearing Installer Is used to quickly and easily seat your OU50407 Inner Pinion Bearing on the pinion. Link to QT2005 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1805 Inner Pinion Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50406 Inner Pinion Bearing Cup a simple and fast procedure. Link to QT1805 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1812 Outer Pinion Bearing Cup Installer Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50400 Outer Pinion Bearing Cup a simple and fast procedure. Link to QT1812 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1088 Differential Step Plate Fits either side of the differential and are used to support the differential when installing your differential bearings or it acts as a push plate when you use a puller to remove the old bearings. Link to QT1088 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1158 Differential Bearing Installer Makes a hard job easy. The raised inside ridge matches against inner differential bearing race allowing you to easily press or drive on QU50398 differential bearing until the bearing is fully seated against the differential adjusting shims. Link to QT1158 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1110 4 Prong Spindle Nut Socket for 4 Slot Round Nuts In 1982 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Use on QU40163 and QU40166 Spindle Nuts. Link to QT1110 Large Text Catalog page for more details
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1025 6 Prong Spindle Nut Socket for 6 Slot Spindle Nuts In 1977-1981 Chevy or GMC K30, K35, and K3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Use on QU40036 Spindle Nuts. Link to QT1025 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1100 Series Driver Handles Are used in conjunction with our seal and bearing cup installers. Link to QT1100 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1033 Case Spreader Is used to relieve the differential bearing preload making it easy to safely remove and install your front differential without damaging expensive critical parts. Link to QT1033 Large Text Catalog page for more details
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1023 Spindle Puller Use with any 5/8" fine thread slide hammer to quickly and easily remove those rusted in front wheel bearing spindles on your GM Dana 60 4x4 without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials on 1977-1991 heavy-duty Chevy or GMC 4x4s. Also works on most Dana 50IFS, Dana 44, Dana 30, Dana 27, and Dana 25 front axles. Link to QT1023 Large Text Catalog page for more details
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1200 Tie Rod Separator Allows you to remove the separate tie rod and drag link ends without wrecking the seals or screwing up your steering linkage ends. Link to QT1200 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT9018 5 Pound Dead Blow Hammer Is just about the first tool you will reach for to complete a multitude of jobs on your Dodge Ram. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool. Link to QT9018 Large Text Catalog page for more details
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT9302 5 Pound Slide Hammer A first-class tool for pulling just about anything you can get a matching 5/8" fine thread puller attachment for. Link to QT9302 Large Text Catalog page for more details
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1801 Outer Wheel Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer makes installing your QU50411 Outer Wheel Bearing Cup a simple and fast procedure. Link to QT1801 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1804 Inner Wheel Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer makes installing your QU50396 Inner Wheel Bearing Cup a simple and fast procedure. Link to QT1804 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QT1505 Wheel Seal Installer Is custom made to quickly and easily install your new wheel seals without damaging them. Link to QT1505 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearings and Seals, Individual

top_page
product note

GM used only the best wheel bearings and seals money can buy to equip their Dana 60 front axles to minimize the chance for warranty problems. That is why they chose Timken® Wheel Bearings and Spicer Wheel Seals for heavy-duty GM 4x4s using the big Danas. We supply those exact original equipment replacement Timken® Wheel Bearings and Spicer Wheel Seals to keep your GM 1 ton on the job for years to come

photo
QU50411 Timken® Outer Wheel Bearing Cup For all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Link to QU50411 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50412 Timken® Outer Wheel Bearing For all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Link to QU50412 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50396 Timken® Inner Wheel Bearing Cup For all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Link to QU50396 Large Text Catalog page for more details
Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU50398 Timken® Inner Wheel Bearing For all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Link to QU50398 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QU40119 Inner Wheel Seal Is a genuine Dana-Spicer original equipment replacement part for 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. Link to QU40119 Large Text Catalog page for more details
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page
product note

General Motors used the same wheel bearing and seal numbers for the entire 1977 to 1991 production run of Dana 60 King Pin type front drive axles. However, and will vary by year, so order those components as needed from the sections above. We offer Wheel Bearing Part/Tool Kits with or without bearing and seal installation tools. If you need a spindle nut socket, see QT1025 for 1977 to 1981 trucks or QT1110 for 1982-1991 models

photo
TK4744 Torque King® 1977-1991 Chevy, GMC Dana 60 Front Wheel Bearing and Seal Kit without Tools Is a parts only (No Tools) complete front Wheel Bearing and Seal Kit for your heavy-duty GM 1 ton featuring Timken® Bearings and original equipment wheel seals for all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. This Kit DOES NOT INCLUDE Spindle Nut Socket or Hub Small Parts for your GM 1 ton!!! Link to TK4744 Large Text Catalog page for more details
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
TK4738 Torque King® 1977-1991 Chevy, GMC Dana 60 Front Wheel Bearing and Seal Kit with Install Tools For all 1977 to 1991 Chevy or GMC K30, K35, K3500, and V3500 1 ton 4x4 trucks with Dana 60 front axles and either single or dual rear wheels. TK4738 includes Timken® Bearings, original equipmDodgeent wheel seals, and installation tools. This Kit DOES NOT INCLUDE Spindle Nut Socket or Hub Small Parts for your GM 1 ton!!! Link to TK4738 Large Text Catalog page for more details
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

(Continued from Top of Page)... Chevy used the model number K30 to designate it's 1 ton 4x4 and the GMC version was K35. Later on, first GMC and later Chevy switched to K3500. When GM introduced the new K-series aerodynamic body style in 1988, the old square body style 1 ton 4x4 became a V3500 until the end of production in 1991. GM also used the Dana 60 front axle in 1984 to 1988 military CUCV models based on the civilian Blazer and GM pickup bodies. Mechanically, the front axles are almost identical to the civilian axles except there was no lockout hub option and military trucks could have a Trac-Lok limited slip front differential.