Parts for GM New Process NP241C Transfer Case with Left Drop in Chevy, GMC Trucks

Bearings

top_page
photo

QU50114 1 Piece NP241C Chevy and GMC Transfer Case Mainshaft Front Pilot Bearing and Cup is an original equipment, unitized drawn cup bearing that replaces X10000 Bearing and QU50083 Sealing Plug in many New Process chain drive transfer cases. The one-piece design of this bearing simplifies installation. This Bearing fits in the back of the input shaft to support the front of the mainshaft (rear output shaft).

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50244 Input Shaft to Mainshaft Pilot Bearing for some New Process and New Venture NP241C transfer cases up to light 3/4 ton class 4x4s

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50157 Transfer Case Front and Rear Output Ball Bearing for New Process NP241C Chevy and GMC transfer cases. QU50157 bearing will provide many years of reliable service. It is locked in place by QU10874 Snap Ring in the front case half on many New Process chain drive transfer cases. Imported.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50502 Caged Needle Bearing for New Process Chain Drive Transfer Cases is an original equipment bearing used to support the rear of front output shafts on all 1987-up NP241C New Process Transfer Case aluminum, chain drive transfer case models. Made in U.S.A.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50873 Wide Transfer Case Input Ball Bearing is used on many New Process NP241C Chevy and GM built chain drive transfer cases in full-size SUVs and 4x4 trucks up to 1-ton rating. This 15/16" wide bearing can only be used with input shafts made to accommodate it's special width. It is NOT interchangeable with QU50874 standard width bearing. This imported bearing is the current production Original Equipment replacement part.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50874 Narrow Transfer Case Input Ball Bearing fits many New Process NP241C Chevy and GM built transfer cases in full size SUVs and 4x4 trucks up to 1-ton ratings. QU50874 is the current original equipment bearing supplied by New Venture and it will provide many years of reliable service. Includes snap ring is pre-installed in bearing groove.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50875 Transfer Case Output Ball Bearing fits New Process NP241C Transfer Case uses 2: Rear Output Rear Bearing and Front Output Front Bearing. Genuine original equipment bearing will provide many years of reliable service. This imported bearing is the current production Original Equipment replacement part.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

X10000 Mainshaft Front Pilot Bearing is used with QU50083 Plug. Both the X10000/QU50083 combo and QU50114 1 Piece bearing were used in original equipment applications and are functionally interchangeable. This Bearing fits in the back of the input shaft to support the front of the mainshaft (rear output shaft).

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50083 Sealing Plug for Input Shafts is used with X10000 Mainshaft Pilot Bearing to prevent oil from leaking through the inside of the Input Shaft on many New Process NP241C Chevy and GMC chain drive transfer cases.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Bearing Retainers

top_page

QU30224 Transfer Case Rear Output Bearing Retainer with Speedo Hole for Chevy and GMC NP241C transfer cases.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU30237U Used 1989 NP241C Rear Output Bearing Housing for 1989 Chevy and GMC Blazer and V1500/V2500 Suburban transfer cases having mechanical speedometer drive.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50501 Input Bearing Retainer is a genuine original equipment part that fits many New Process NP241C Chevy and GM chain drive transfer cases. Due to numerous design changes in the molds used over the years, this new retainer may look different than your original retainer, but it will directly replace your damaged or broken retainer.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Bushings

top_page
photo

QU10130 Chevy/GMC NP241C Rear Output Bushing Is a genuine original equipment bushing that gets pressed into the rear extension housing to support the driveshaft slip yoke.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Case Halves and Brand New Transfer Case Assemblies

top_page
photo

QU50344 Rear Case Half is a genuine New Process Gear replacement part for many left drop New Process NP241 series Transfer Cases in Dodge and General Motors full-size 4x4s. These brand new housings include a pre-installed QU50502 Front Output, Rear Needle Bearing. Made in U.S.A. For drain and fill plugs, order 2 QU11044 Plugs.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Case Parts

top_page
photo

QU11092 Breather Vent for NP241C Transfer Cases is a genuine original equipment vent for the front case half on some NP241C Transfer Cases.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10939 New Process and New Venture Transfer Case Drain or Fill Plug is a genuine, original equipment New Process redesigned plug to replace either (or both) the drain and fill plugs on your NV241C Transfer Case.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11044 Metric Transfer Case Drain or Fill Plug is a genuine New Process original equipment part that fits many NP241C Chevy and GMC chain drive New Process Transfer Cases. Includes plastic gasket and sealant pre-applied to threads.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50191 Chip Magnet for New Process NP241C Transfer Cases is a genuine original equipment Chip Magnet that fits a host of Transfer Cases manufactured by New Process Gear.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Drive Chains

top_page
photo

QU50071 Transfer Case Drive Chain 1-1/4" wide Genuine Morse HY-VO™, USA made, original equipment transfer case drive chain fits many 1998 and newer Chevy and GMC New Process NP241C Transfer Cases.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets

top_page
photo

TK30052 6 Bolt Round Transfer Case Adapter Gasket fits between your GM 4x4 transmission and 32 spline input NP241C transfer case. TK30052 is the current original equipment service part.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Input Shafts

top_page

QU30202 32 Spline Input Shaft for GM NP241C transfer cases with 5/8" NARROW input bearing.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU50828 32 Spline Input Shaft for GM NP241C transfer cases with 15/16" WIDE input bearing.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Oil Pumps and Oil Pump Pickup Parts

top_page
photo

QU50423 Oil Pump for 32 Spline New Process NP241C Transfer Cases is a genuine original equipment New Process Gear Oil Pump for many Chevy, and GMC 4x4s with 32 spline Rear Output Shafts.

More Info

Also available QU10972 Aftermarket 32 Spline Oil Pump.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10673 Oil Pump Pickup Connector Hose connects the QU10674 Oil Pickup Filter Screen to QU10823 Oil Pump Feed Tube on many New Process NP241C chain drive Transfer Cases in Chevy and GMC 4x4 vehicles. This genuine New Process Hose has the correct flexibility and oil resistance needed for long life.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10674 New Process Transfer Case Oil Pickup Screen is a genuine New Process Gear replacement part. Your Oil Screen is located at the bottom of the case just above the chip magnet. The plastic screen filters out chips and crud from the oil before it gets to the pump. QU10674 Oil Pump screen fits all drivers side drop NP241C series Transfer Cases.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10823 Steel Oil Pump Feed Tube is used to transfer oil from the QU10674 Pickup Screen to QU50423 Oil Pump on most 1998 and newer NP241C transfer cases with driver's side drop. Genuine original equipment part.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

O-Rings

top_page
photo

QU10678 Speedometer Adapter O-Ring fits many Chevy and GMC New Process chain drive transfer cases using Delco type speedometer adapters. This O-Ring fits in the groove machined in the adapter and seals against the machined hole in the transfer case bearing support.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10800 Poppet Plug, Vacuum Switch to Case O-Ring, or Speed Sensor O-Ring One or two of these O-Rings are used on many New Process NP241C chain drive transfer cases for sealing the Poppet Plug, Speed Sensor, and/or Indicator switch on 1980's to current Chevy and GMC 4x4 vehicles. Order one or two per transfer case as needed.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10802 Oil Pump Feed Tube to Oil Pump O-Ring for most New Process chain drive transfer cases to seal the connection between your oil pump and the oil pump feed tube. This O-ring is found on many models of New Process transfer cases in Chevy and GMC from the 1980's to the present. Some of the common matching parts are QU50423 oil pump, QU10936 oil pump, and QU10823 Oil Pump Feed Tube.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10825 Sector Shaft Inner O-Ring seals the sector (shift cam) shaft to keep oil in and water out. Fits many models of New Process chain drive, mechanical shift transfer cases. Use in conjunction with QU10824 Outer Seal Ring.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Output Flanges and Yokes

top_page

QU30268 31 Based on 32 Spline Rear Output Slip Yoke for GM NP241C transfer cases.  Approx. 8" long from end to center.

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50043 Transfer Case Front Output CV Flange Yoke for New Process NP241C Chevy and GMC Transfer Cases. May be some slight surface rust from long storage.

More Info

Also See QK2006 CV Flange Kit.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Output Shafts

top_page

QU50154 32 Spline Rear Output Shaft for New Process NP241C Transfer Cases fits many 1998 and newer Chevy and GMC transfer cases.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Planetary Assemblies

top_page
photo

QU50153 6 Pinion Planetary Carrier for New Process Transfer Cases A genuine original equipment New Process Gear replacement assembly with 6 pinion gears that fit many New Process NP241C chain drive transfer cases in full size 4x4s.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Poppet Parts

top_page
photo

QU50947 Poppet Spring for NP241C Transfer Cases is a genuine New Process part.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11018 Poppet Plunger is a genuine New Process gear replacement part that fits New Process NP241C Chevy and GMS chain drive transfer case models. Not a common part to fail, but when the tip wears, the transfer case will have a tendency to jump out of gear.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Seals

top_page
photo

QU10857 Genuine New Process Input Seal Seal features raised rubber outer sealing ring to seal against retainer chamfer and high-temp resistant Viton seal lip with outer wiper.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40366 Transfer Case Output Oil Seal fits New Process NP241C Chevy and GMC chain drive transfer cases for both front and rear output applications. This seal features a bidirectional hydrodynamic lip design to minimize seepage and a flanged steel shell that simplifies installation and removal. Pliable red sealant is applied to exterior of shell for leak-proof bond between seal and transfer case housing.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50177 Genuine New Process Oil Pump Seal is an exact original equipment manufacturer replacement Seal that fits most New Process NP241C Chevy and GMC chain drive transfer cases.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50514 Transfer Case Output Seal is a genuine NPG original equipment Seal with triple seal lip construction. The protective outer lip deflects road splash and debris and the inner 2 lips seal oil in. QU50514 fits 1988-2004 chain drive New Process NP241C Chevy and GMC Transfer Cases with fixed type 1-7/8" hub diameter, front output yokes.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK10513 Spline Seal for 32 Spline Output Shafts and Remote Mount Input Shafts (Also known as Splined Washer) is a genuine New Process part used to seal oil from leaking past the yoke splines on most New Process NP241C Chevy and GMC 32 Spline front or rear Fixed Yoke Output Shafts. This 32 Rubber Spline Seal is approximately 0.182" thick. Made in U.S.A.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK10517 Genuine NPG Transfer Case Input Seal for New Process NP241C Chevy and GMC aluminum case transfer cases, 32 Spline Input GM models behind automatic and manual transmissions. This genuine New Process original equipment quality Seal is a double lip, double spring seal designed to retain fluids from either direction.
Also see lower cost QU50461 replacement seal.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK50358 Double Lip Rear Output Seal for Slip Yoke Applications for many New Process NP241C Chevy and GMC chain drive transfer cases with 32 spline slip yoke type rear output shafts. Genuine New Process Original equipment seal has a hydrodynamic inner lip to keep oil in and and an outer wiper lip to deflect road road splash and crud.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10824 Plastic Sector Shaft Outer Seal is a genuine New Process part that fits many New Process chain driven transfer case. This Outer Seal protects QU10825 Sector Shaft Inner O-Ring from road splash and grit.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Shift Forks and Shift Hubs

top_page
photo

QU50078 Aluminum Range Fork with molded shift fork pads is a genuine New Process part that fits many New Process/New Venture chain drive transfer cases in mid 1990s and newer 4x4s.

More Info

photo

QU50152 Range Shift Hub for NP241C Transfer Cases is a genuine original equipment New Process part.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Shift Parts

top_page
photo

QU10164 Mode Fork or Range Fork Shift Pad for NP241C Transfer Cases. Genuine, original equipment New Process gear pads. Requires 2 per Fork.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10670 Mode Fork Center Shift Pad for NP241C Transfer Cases is a genuine original equipment New Process plastic, curved shift fork pad.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
photo

QU50916 Basic Small Parts Kit for New Process NP241C Chevy and GMC Transfer Cases.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10512 Front Output Flange Lock Nut for Chevy and GMC Full Size 4x4 trucks with New Process NP241C part time transfer cases equipped with either square or round front output flanges. Alloy flange nut is plated for anti-corrosion protection.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10572 Input Shaft to Planetary Thrust Washer These genuine New Venture original equipment Thrust Washers are used between the Input Gear and Planetary Assembly on New Process NP241C chain drive transfer cases with planetary low range units.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10986 Synchro Strut for New Process Early NP241C synchronized transfer cases

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11039 Planetary Lock or Thrust Plate for New Process Chain Drive Transfer Cases is a genuine original equipment part that fits most New Process NP241C Chevy and GMC chain drive transfer cases with low range. The Tanged Lock Plate is the heavy 1/8" thick cast iron thrust plate that is located between the outer plastic Planetary Thrust Washer and the Planetary Snap Ring.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50498 1/2" ID Plastic Pinion Gear Thrust Washer for NP241C Transfer Cases is a genuine original equipment NVG part that fits the planetary gears on chain drive, aluminum case New Process Chevy and GM Transfer Cases. Machine shop services required to replace these thrust washers.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Snap Rings

top_page
photo

QU10814 Input Shaft to Planetary Snap Ring is a genuine New Process original equipment part for New Process NP241C chain drive transfer cases 4x4 vehicles. QU10814 secures the Input Shaft and Planetary Thrust Washers inside your planetary assembly.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10816 Mainshaft or Rear Output Shaft to Rear Output Bearing Snap Ring is a genuine New Process Part used on many Chevy and GMC NP241C New Process and New Venture transfer cases with slip yoke rear output shafts from 1980 and newer. This Snap Lock (Ring) is installed on the rear output shaft just aft of the rear output bearing.

More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10818 Front Output Sprocket to Front Output Shaft Snap Ring is a genuine original equipment part for chain drive New Process NP241C transfer cases. QU10818 fits in a groove machined in the Front Output Shaft to secure the Driven Sprocket is in place.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10872 Synchro Hub to Mainshaft Snap Ring for many 1998 and newer Chevy and GMC NP241C synchronized Transfer Cases

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10873 Speedo Gear Snap Ring Original equipment retaining snap ring for New Process NP241C transfer case speedometer drive gear.

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10874 Front Output Shaft Bearing to Front Case Snap Ring for Chevy and GMC 241C synchronized Transfer Cases is used to lock QU50157 Front Output Shaft Front Bearing in place in the front case half on many New Process chain drive transfer cases. This genuine original equipment New Process part is Made in U.S.A.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10899 Annulus Gear Snap Ring is the large Snap Ring that retains the big planetary annulus gear in your front case half. This genuine New Venture part fits a multitude of NV241C New Process and New Venture Transfer Case chain drive units with planetary low range in Chevy and GMC 4x4s.

More Info

photo

QU10979 New Process Transfer Case Synchronizer Strut Tension Spring Two of these springs are used in 1988-1998 NP241C synchronized transfer cases to apply tension to the three QU10821 Synchro struts or keys.

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU30039 Input Gear Snap Ring for some NP241C Transfer Cases

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Sprockets

top_page
photo

QU50513 1-1/4" Wide Lower (Driven) Sprocket fits some New Process NP241C chain drive transfer cases with 1.25" wide drive chains. Genuine original equipment New Process Part. Use QU10818 Snap Ring to secure this sprocket to your front output shaft

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Synchronizer Parts

top_page
photo

QU11299 48 Tooth Synchro Ring for many 1998 and newer Chevy and GMC New Process NP241C Transfer Cases

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10979 New Process Transfer Case Synchronizer Strut Tension Spring Two of these springs are used in 1988-1998 NP241C synchronized transfer cases to apply tension to the three QU10821 Synchro struts or keys.
More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10986 Synchro Strut for New Process Early NP241C synchronized transfer cases

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
photo

QT2050 Transfer Case Rear Output Bushing Remover and Installer for New Process 1987-1998 NP241C GM Transfer Cases with Slip Yoke style rear output shafts. Change the rear output bushing on your transfer case the easy way and without wrecking the housing or bushing!

More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!