QU30203 Brand New NP246GM Electric Shift Transfer Case assembly with 27 spline input shaft.
QU30204 Brand New NP246GM Electric Shift Transfer Case with 32 spline input shaft.
All GM 1998-2007 GM NP246 Transfer Cases use the same Bearing, Seal, and Gasket Kit
QU30282 NP246C Bearing, Seal, and Gasket Kit includes all the Bearings, Seals, and O-Rings, plus Planetary Thrust Washers, 3 piece early Shift Fork Pad Set and the Transmission to Transfer Case Adapter Gasket.
QU10897 Transfer Case Input or Front Output Ball Bearing without Snap Ring Groove is an original equipment Ball Bearing for 1998-2007 New Process NP246 Input and Front Output Bearing Usually USA made but can be imported.
QU30030 Shift Shaft Support Bearing for GM NP246 electric shift transfer cases in Chevy and GMC 4x4 trucks.
QU30259 Reinforced Rear Case Half for New Process and New Venture NV246 transfer cases in GM 4x4 trucks features a reinforced oil pump area to prevent premature wear. Includes bushing and output shaft bearing. Fits 1999-2007 Silverado/Sierra 1500, 2500, 1999-2007 Suburban 1500, 2000-2007 Suburban 2500, 1999-2007 Tahoe, Yukon, and 2002-2007 Avalanche 1500, 2500.
QU10130 Small Bore Genuine New Process Rear Output Bushing is a genuine original equipment bushing for many General Motors New Process NP246 Transfer Cases in full size 4x4's from 1980-up.
QU50288 Morse Original Equipment Transfer Case Chain for New Process Chevy/GMC NP246 1999-up Pickup and Full Size SUV transfer cases. Replaces chains with THREE Blue Guide Links. QU50288 has 98 3/8" x 1-1/4" links with RJ pins.
QU50262 1 1/4" Wide Morse Transfer Case Drive Chain for New Process NP246C chain drive transfer cases
QK2190 Clutch Plate Kit for NP246 Transfer Cases. Includes 10 Inner Friction Clutches and 9 Steel Outer Clutch Plates.
QU50764 Original Equipment Clutch Apply Plate for GM NP246 electric shif transfer cases.
See QU30284 for our OE replacement part
QU50769 Inner Clutch Plate for NP246 Transfer Cases. Use 10 per transfer case.
QU50770 Original Equipment Steel Outer Clutch Plate for GM NP246 electric shift tranfer cases
See QU30285 for our aftermarket option
QU11145 Inner Clutch Drum to Mainshaft Snap Ring for Chevy and GMC NP264 and NV246 series electric shift transfer cases.
QU30299 Oil Tube Pickup Assembly for New Process and Vew Venture 246 series transfer cases.
QU50490 38 Spline Transfer Case Oil Pump for NP246 is a genuine New Process OEM part
QU30031 Transfer Case Input Seal is a genuine New Venture double lip, double spring Seal for many NP246 Transfer Cases in Chevy and GMC mid and full size 4x4s. Double lip design seals oil from both sides so it can function both as the transmission output Seal and Transfer Case input Seal.
QU30032 Unitized Transfer Case Front Output Seal is a genuine original equipment New Venture Seal for Chevy and GMC full size 4x4s NP246 Transfer Cases. This is an oil-bath type Seal that has a built in wear sleeve that presses over your front output shaft. The Wear Sleeve rotates inside the main seal during operation. Made in U.S.A.
QU30290 Rear Output Seal for New Process NP246 transfer cases with slip yoke type rear output.
QU30286 Basic NP246 Small Parts Kit for all 1998-2007 GM and 2006-2010 Dodge New Process or New Venture NP246 transfer Cases. Kit includes most snap rings, oil pump wave spring, and 1998-2002 Shift Fork Pads.
QU30023 Case Access Plug for the rear output bearing snap ring on GM NP246 Transfer Cases.
QU30029 Transfer Case Extension Housing Plug for NP246 transfer cases.
QU30288 Oil Pump Wave Washer for New Process NP246 transfer cases.
QU10898 Transfer Case Snap Ring for Input or Front Output Ball Bearing is an original equipment Ball Bearing for 1998-2007 New Process NP246 Input and Front Output Bearing. QU10898 is used to retain QU10897 Ball Bearing, it fits in a groove machined in the front transfer case half. Made in U.S.A.
QU30021 Output Bearing Lock Ring for NP246GM rear outputs.
QU50030 Chain Sprocket for GM New Process NP246 transfer cases.