Parts for Dana-Spicer Closed Knuckle Model 44 Solid Beam Front Axles in 1957-1973 Jeep 4x4 Trucks

Jeep first used the Dana 44 Closed Knuckle Beam Type Front Axle in the 1957 cab over engine Forward Control (FC) series of 4x4 trucks. The Dana 44 will be found in FC150 trucks with the 57" wide track option which was basically a 1/2 ton short bed truck. Also using the Dana 44 axle was the long wheel base FC-170 3/4 ton to 1 ton truck which was available with either single or dual rear wheels. Jeep built FC series trucks through the 1965 model year. The 1962-1973 Jeep Gladiator line of trucks would also use the Solid Beam Dana 44 closed knuckle axle as the stock axle. A Dana 44IFS axle was available as on option for 1963 to 1965 model years. The Gladiator line was built in 1/2 ton and 3/4 ton single rear wheel versions, plus a dual rear wheel 1 ton truck.

Axle Identification

top_page
photo
Cover: 10 Bolt, 10-3/8" high
Ring Gear:

Axle Shaft Seals and Seal Kits

top_page
product note

All 1962-1973 Jeep J-Series models have Inner Axle Shaft Oil Seals pressed in the inboard end of each axle tube, right next to the differential side bearings. These seals contact the inner axle shafts to prevent gear oil from running out of the differential and down the axle tubes. Old age, blown axle u-joints, and/or grit that works it's way into the axle tubes and cuts the seal are the usual causes of failure. A bad Inner Axle Shaft Seal can be detected by oil coming out the end of the axle tubes next to the axle shaft u-joint. Usually when these Seals start to fail, they will seep oil so the leakage may go undetected for quite some time. Many a ring and pinion set has been burned up from axles that lost all their lube when long term seepage was not noticed. Several different Seals were used depending upon year and vehicle model. Axle disassembly including differential removal is required to replace the Seals

photo
QU40055 1962-1973 Inner Axle Shaft Oil Seal With integral axle shaft guide for all 1962-1973 Jeep J-Series Dana 44 Front Drive Axles. One of these Seals are installed in each axle tube, right next to the differential to keep gear lube from leaking out the ends of the axle housing. QU40055 Unitized Seal replaces the original two piece QU42015 seal and separate sheet metal guide.

Please refer to QU40055 page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4871 1962-1973 Jeep Dana 44 Axle Seal Kit with Fixed Depth Axle Seal Tool Set Quickly and easily installs QU40055 Unitized Inner Axle Seals to a precise depth in 1962-1973 Jeep Dana 44 Front Drive Axles. Our unique installer design will press in new your Inner Axle Seals to the exact depth and without damage because the CNC Precision Machined Installation Tool cups the seal so force is only applied on the steel seal shell.

Please refer to QK4871 page for more details and ordering information.
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo
QK4872 1962-1973 Jeep Dana 44 Axle Seal Kit with Adjustable Depth Axle Seal Tool Set Quickly and easily installs QU40055 Unitized Inner Axle Seals in 1962-1973 Jeep Dana 44 Front Drive Axles. Our unique installer design will press in new your Inner Axle Seals without damage because the CNC Precision Machined Installation Tool cups the seal so force is only applied on the steel seal shell.

Please refer to QK4872 page for more details and ordering information.
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Axle Universal Joints

top_page
product note
The Jeep Closed Knuckle Dana 44 axle uses solid cross, inside lock-up universal joints without seals that are designed to be bathed in a semi-liquid lubricant from inside the closed knuckle balls. By today's standards, these u-joints are way undersized, but given the lighter vehicle weights and modestly powered engines of the late 1950's to the early 1970's, the joint size was probably adequate
photo
QU40507M Axle Universal Joint for Jeep Dana 44 Closed Knuckle Front Axles Is a genuine original equipment axle manufacturer, solid-cross, non-greaseable, front axle u-joint without seals for 1957-1973 Jeep Dana 44 closed knuckle front axles. Link to our QU40507M Large Text Product Page.

Please refer to QU40507M page for more details and ordering information.
Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Closed Knuckle Parts

top_page
product note

We stock the regular service closed knuckle parts for your 1957-1973 Jeep 4x4 truck with a closed knuckle Dana 44 front axle which will have 8 bolt Knuckle Ball Hemisphere Seals. With a Closed Knuckle axle, the axle universal joints and king pin bearings are lubricated by very heavy oil or a viscous grease that will flow when the axle shafts rotate. A large, multi-piece seal is bolted to the backside of the steering knuckle to keep lubricant in and water out. On poorly maintained closed knuckle axles or axles equipped with lockout hubs that are rarely used in 4x4, the upper king pin bearing and axle universal joint can suffer from lack of lubrication. The Ball Seals will usually weep some lubricant especially when standard gear oils are used as a lubricant. Submersion of the axle under water or condensation from temperature changes can cause moisture to build up inside the enclosed ball and lead to corrosion damage and part failures

photo

QK4617 1957-1973 Jeep Truck Dana 44 Closed Knuckle Front Axle Knuckle Bearing Kit Includes 4 Timken® Knuckle Bearings, 4 Timken® Knuckle Bearing Cups, and Rectangular Knuckle Shim Set to service both sides of your vintage 1957-1965 Forward Control or 1962-1973 J-Series 4x4 truck. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TKA4939 Premium Torque King® Knuckle Shim Kit for Dana Closed Knuckle Front Axles with 8 Bolt Ball Seals includes the four shim thicknesses that Dana used for setting precise knuckle rotating preload on your vintage 1957-1965 Forward Control or 1962-1973 J-Series 4x4 Dana 44 closed knuckle front axles. Each TKA4939 Shim Kit includes: (4) 0.003", (3) 0.005", (3) 0.010", and (1) 0.030" shims so you can precisely adjust your knuckle rotating preload to optimum specifications. TKA4939 services one side of your axle. Order 2 Kits per axle. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40773 Knuckle Shim Kit for 1957-1973 Jeep Truck Dana 44 Closed Knuckle Front Axles with 8 Bolt Ball Seals Includes a selection of rectangular shims to adjust the Knuckle Bearing preload. Services one side of your vintage 1957-1965 Forward Control or 1962-1973 J-Series 4x4 truck. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40188 1957-1973 Jeep Truck 8 Bolt Knuckle Ball Seal Kit for Dana 44 Standard Front Axles Is a genuine original equipment Kit for Dana 44 standard duty closed knuckle front axles in 1957-1965 Forward Control or 1962-1973 J-Series 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50627 1957-1973 Jeep Truck Dana 44 Closed Knuckle Timken® Knuckle Bearing Cup For Dana 44 Standard Duty closed knuckle front axles in 1957-1965 Forward Control or 1962-1973 J-Series 4x4 trucks. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50628 1957-1973 Jeep Truck Dana 44 Closed Knuckle Timken® Knuckle Bearing For Dana 44 Standard Duty closed knuckle front axles in 1957-1965 Forward Control or 1962-1973 J-Series 4x4 trucks. More Info

* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential and Pinion Bearings (Individual)

top_page
product note

There was a Jeep Dana 44 differential Side Bearing change which occurred during the 1967 to 1968 model years, The Jeep Parts Books show the changeover by by referencing it to Jeep axle assembly part numbers instead of by year. The very early production trucks with 258-6 and 358-V8 engines will have the earlier, small ID bearing. From what I can remember from working on them, almost all the mid-1967 and newer trucks had the new bearing with the exception of some heavy GVW models that did not change until late 1967 or early 1968. If you have a 1967 or 1968 model year Gladiator truck, you should verify what diff side bearing you have before ordering!
All bearings are not created equal for fit or durability, so we only stock first class, long lasting, Timken® Differential and Pinion Bearings for your Dana front axle. Timken® was and is a a major original equipment supplier of top-notch bearing components to Dana Spicer. Since I first started rebuilding Dana axles in the mid 1970's, I have found Timken® Bearings to be the most consistent in relation to the published dimensions of any bearing on the market which makes rebuilding an axle right the first time a WHOLE lot easier!

photo

QU50533 Timken® Outer Pinion Bearing Cup For 1957-1965 Jeep FC150, FC170 Forward Control 4x4s and 1962-1973 J-Series 4x4 trucks with Dana 44 closed knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50534 Timken® Outer Pinion Bearing For 1957-1965 Jeep FC150, FC170 Forward Control 4x4s and 1962-1973 J-Series 4x4 trucks with Dana 44 closed knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50535 Timken® Inner Pinion Bearing Cup For 1957-1965 Jeep FC150, FC170 Forward Control 4x4s and 1962-1973 J-Series 4x4 trucks with Dana 44 closed knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50536 Timken® Inner Pinion Bearing For 1957-1965 Jeep FC150, FC170 Forward Control 4x4s and 1962-1973 J-Series 4x4 trucks with Dana 44 closed knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50538 Timken® Large Inside Diameter Differential Side Bearing For 1962-1966 plus 1967-1973 J-Series 4x4 trucks with Dana 44 closed knuckle front axle that has differential side bearing with an inside diameter of 1.796". (Uses 2.) [Some early 1967 or 1968 trucks may use QU50683 bearing.] More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50683 Timken® Small Inside Diameter Differential Side Bearing For Jeep 1957-1965 FC150, FC170 Forward Control 4x4s and 1962-1966 J-Series 4x4 trucks with Dana 44 closed knuckle front axle that has differential side bearing with an inside diameter of 1.688". (Uses 2.) [Some early 1967 or 1968 trucks may also use this bearing.] More Info

photo

QU50537 Timken® Differential Side Bearing Cup For 1957-1965 Jeep FC150, FC170 Forward Control 4x4s and 1962-1973 J-Series 4x4 trucks with Dana 44 closed knuckle front axles. (Uses 2.) More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Differential Parts

top_page
photo

QU30170U Loaded Differential Case For Dana 44 with 3.92 to 5.89 ratio gear sets and 30 spline axle shafts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40632 Empty Differential Case Kit For Dana Model 44 3.73 and numerically lower ratios. Includes ring gear bolts and diff shims. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40633 Loaded Differential Case Assembly For Dana Model 44 3.73 and numerically lower ratios. Includes spider gears, diff bearings, ring gear bolts and diff shims. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40675U Good Used Loaded Dana 44 30 Spline Open Differential Assembly for 3.73 and faster gear ratios. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40634 Empty Differential Case Kit For Dana Model 44 3.92 and numerically higher ratios. Includes ring gear bolts and diff shims. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40635 Loaded Differential Case Assembly For Dana Model 44 3.92 and numerically higher ratios. Includes spider gears, diff bearings, ring gear bolts, and diff shims. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Gaskets and Gasket Makers

top_page
product note

Depending upon the year, a cut gasket or RTV sealant was used by Dana-Spicer to seal the differential cover. Early, thin gauge covers with embossed flanges are made for use with a cut gasket. Later thick gauge covers with flat flanges are designed for sealing with RTV or if you desire, you can use a combination of a cut gasket with thin films of RTV. We stock both genuine Dana Gaskets and Ultra Gray RTV Sealant which has high adhesion and excellent resistance to synthetic lubricants

photo

QU42028 Dana 44 Reusable Diff Cover Gasket is a steel core performance gasket that can be reused multiple times. These Teflon® coated gaskets feature a no re-torque design and will save time when working on your diff by eliminating the need to clean the metal mating surfaces of old gasket material plus you do not have to wait hours for a sealant to cure! More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40214 Dana 44 Cover Gasket Is a genuine original equipment Dana Gasket for all Dana-Spicer Model 44 axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

TK40573 Torque King® 6 Bolt Front Hub Gasket Fits 1969-1973 Jeep heavy-duty J4000, J4800, and Camper Special 4x4 trucks with Dana 44 closed knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU15005 Front Hub Gasket For 1957-1971 Jeep Dana 44 closed knuckle front axles. QU15005 fits between your wheel hub and drive hub flange. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

S82194 Ultra Gray RTV Sealant Combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Dodge Ram front axle. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Hubs and Hub Parts

top_page

QU15027 Warn Premium Lock Out Hub Set Fits 1957-1973 Jeep trucks with Dana 44 closed knuckle front axles, 1-1/8" 10 spline axle shafts and a hub face bolt circle of 3-7/16". These hubs are the best quality, sharpest looking, and longest lasting hubs for your Jeep bar none. Kit includes 2 brass dial manual hubs. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU15026 Bestlok Lock Out Hub Set for 1969-1973 Camper Special, J4000, and J4800 Fits 1969-1973 Jeep heavy-duty J4000, J4800, and Camper Special 4x4 trucks with Dana 44 closed knuckle front axles, 1-1/8" 10 spline axle shafts and a hub face bolt circle of 3-3/4". These hubs are probably the last New Old Stock (NOS) hub sets for these rare Jeep 3/4 ton trucks in existence. A quick turn of the dial lets you engage and disengage your front axle shafts from the wheels. Disengage for better mileage, towing, and to reduce wear on your front diff and driveshaft. Engage for solid and reliable 4x4 traction. Kit includes 2 plastic dial manual hubs

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Manuals and Technical Information

top_page
product note

Dan the Gear Man® Product Note: Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations.

photo

TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Miscellaneous Parts & Lubricants

top_page
product note

Replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings

photo

QU90009 Universal Axle Service Pack Is the Bargain Priced Chemical Service Pack included in many of our QU series Differential Bearing Kits. You get Threadlocker for the ring gear bolts, diff cap bolts, and pinion nut, QU90008 Gear Marking Compound for checking the tooth pattern on your gear set, Blue RTV sealant for the diff cover and a small brush to apply the Gear Marking Compound. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Pinion Seals and Pinion Yokes

top_page
product note

Jeep used both 10 spline and 26 spline Pinion Yokes on 1957-1973 Dana 44 Closed Knuckle Front Axles depending upon the year and universal joint. The only yoke currently available is the 26 spline QU40849 which was used on the J-Series models.

photo

QU40215 Dana 44 Front Axle Pinion Seal Is a genuine original equipment pinion seal for all 1957-1965 Jeep FC150, FC170 Forward Control 4x4s and 1962-1973 J-Series 4x4 trucks with Dana 44 closed knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40849 26 Spline Dana 44 Front Pinion Yoke Directly replaces worn or broken factory Pinion Yokes made for 3-7/32" wide universal joints with 1-1/6" diameter cups on 1962-1973 J-Series 4x4 trucks with Dana 44 closed knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40768 Pinion Yoke U-Bolt Kit fits QU40849 Pinion Yoke. Use this Kit to replace broken or stripped original u-bolts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Ring and Pinion Kits

top_page

QU40177 Genuine Dana 4.09 Ratio Ring and Pinion Kit With pinion bearings, pinion seal, and small parts for standard Dana 44 axles. Use with 26 spline pinion yoke. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU30169U Used Dana 44 4.09 Ratio Ring and Pinion is a good used genuine Dana OEM 4.09 ratio gear set with a 26 spline pinion shaft. These good used gear sets are taken from axle assemblies our Research and Development Department had for part verification and tool design purposes. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

QU40447 Genuine Dana 3.54 Ratio Ring and Pinion Kit With pinion bearings and small parts for Dana 44. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU42098U Serviceable Used 3.54 Ratio Dana 44 Ring and Pinion Set. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Small Parts

top_page
product note

Dan the Gear Man® Product Note: As with most repair jobs, it is the little things that make the difference between a poor job and a repair that will last. We stock many of those small but vitally important small parts for your 1957-1973 Jeep® Dana 44 closed knuckle front axle

photo

QU40009 Pinion Nut Is a genuine original equipment Dana 44 Pinion Lock Nut for all 1957-1965 Jeep FC150, FC170 Forward Control 4x4s and 1962-1973 J-Series 4x4 trucks with Dana 44 closed knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU40010 Pinion Washer Is a genuine original equipment Dana 44 Pinion Flat Washer for all 1957-1965 Jeep FC150, FC170 Forward Control 4x4s and 1962-1973 J-Series 4x4 trucks with Dana 44 closed knuckle front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindles and Spindle Nuts

top_page
product note

1957-1973 J-Series Jeeps with with 5 bolt wheels and manual lock-out hubs or solid drive flanges use the same four piece spindle nut parts as the World War II military MA and MB Jeeps. A thrust washer is used between the outer wheel bearing and inner spindle nut. The inner nut adjusts the wheel bearing end-play. The outer nut functions as a lock nut, it is held in place by a bend-over lock washer located between the two nuts. Vehicles with Warn Lock-O-Matic Hubs require special lockwashers and round outer nuts. 1969-1973 J4000 and J4800 trucks use bigger spindles and spindle nut parts

photo

QU15062 Front Spindle for 1973 Jeep J4800 Dana 44 Closed Knuckle Front Axles. Also, fits some 1968-1972 Jeep Trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU15064U Used Jeep J-Series Spindle for most 1968-1973 Jeep J-Series Full Size Wagoneer and 1/2 Ton Trucks with Closed Knuckle Front Axles and 1-5/8" Spindle Threads. While supply lasts. More Info 

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QK4669 Hex Spindle Nut Kit for Jeep Dana 44 Front Axles Includes inner thrust washer, spindle lock washer, and two 2-1/16" OD hex spindle nuts with 1.5" threads. Fits most Forward Control, Jeep Wagoneer and J-Series truck models with Dana 44 closed knuckle front axles with manual hubs or splined drive flanges from 1957 to 1973. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU15000 Front Spindle Inner Thrust Washer for Scout and Jeep Fits between your outer wheel bearing and inner spindle nut on most Forward Control, Jeep Wagoneer and J-Series truck models with Dana 44 closed knuckle front axles with manual hubs or splined drive flanges from 1957 to 1973. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU15001 Front Spindle Nut for Scout and Jeep 1-1/2" Thread X 2-1/16 Hex Front Spindle Nut for most Forward Control, Jeep Wagoneer and J-Series truck models with Dana 44 closed knuckle front axles with manual hubs or splined drive flanges from 1957 to 1973. Use two per side. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU15002 Front Spindle Lock Washer for Jeep Fits between your inner and outer spindle nuts on most Forward Control, Jeep Wagoneer and J-Series truck models with Dana 44 closed knuckle front axles with manual hubs or splined drive flanges from 1957 to 1973. Bend washer over flat on outer nut to lock spindle nuts in place. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU10576 Bend Over Tab Lock Washer for 1969-1973 Jeep J4000, J4800, and Camper Special Dana 44 Front Axles and 1-3/4" Spindle Threads Fits 1969-1973 Jeep J4000, J4800, and Camper Special 4x4 trucks with 1-3/4" thread hex spindle nuts and external mount wheel hubs. Washer has two pre-bent tabs that fit over the inner spindle nut and 6 bend-over tabs for the outer spindle nut. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11164 1-3/4 Thread Spindle Hex Nut for 1969-1973 Jeep J4000, J4800, and Camper Special Dana 44 Front Axles and 1-3/4" Spindle Threads Fits 1969-1973 Jeep J4000, J4800, and Camper Special 4x4 trucks with 1-3/4" thread hex spindle nuts spindle nuts and external mount wheel hubs. Fits 1-3/4" Spindle Threads. Hex size is 2-1/2". Use 2 per side, 4 per vehicle. Sold Individually. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU11165 Spindle Thrust Washer for 1969-1973 Jeep J4000, J4800, and Camper Special Dana 44 Front Axles and 1-3/4" Spindle Threads Fits 1969-1973 Jeep J4000, J4800, and Camper Special 4x4 trucks with 1-3/4" thread hex spindle nuts spindle nuts and external mount wheel hubs. Fits 1-3/4" Spindle Threads. One of these washers is used on each side between the outer wheel bearing and inner spindle nut. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Spindle Bushings

top_page
product note

One of these Bushings are pressed into the inboard side of each spindle to support your outer axle shaft. These are one of the most common 1957-1973 Jeep Dana 44 closed knuckle front end parts requiring replacement as both the thrust face and inside diameter of the Bushing are subject to wear

photo

QU40321 Spindle and Axle Shaft Bushing for 1957-1973 Jeep Dana 44 Closed Knuckle Axles Is a genuine original equipment flanged Bronze Bushing that gets pressed into the back of the spindle to support the axle shafts in your 1957-1973 Jeep J-Series or 1957-1965 Forward Control 4x4 truck. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Tools

top_page
product note

Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 44 front axle in your 1957-1973 Jeep 4x4

photo

QT1011 2-1/16" Hex Front Spindle Nut Socket For 1957-1973 Jeep Dana 44 front axle except for J4800 and Camper Special. Also fits CJ-5, CJ-6, CJ-7, and CJ-8 (Scrambler) and most other Jeep vehicles from 1942-1971 except M715 series. This Special Thin-Wall 1/2" drive socket is an absolute necessity to properly service the front wheel bearings on your vintage Jeep. Also fits IHC Scout. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1044 Inner Pinion Bearing Installer for Dana 44 front axles in all 1957-1973 Jeep Dana 44 Closed Knuckle Front Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1815 Inner Pinion Bearing Cup Installer Attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50539 Inner Pinion Bearing Cup a simple and fast procedure. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1812 Outer Pinion Bearing Cup Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer makes installing your QU50533 Outer Pinion Bearing Cup a simple and fast procedure. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1100 1" x 8" Standard Duty Driver Handle is used in conjunction with our seal and bearing cup installers. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1101 1" x 14" Standard Duty Driver Handle Use for deep seated seals & bearings. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1116 1¼" x 8" Pro-Duty Driver Handle 1-1/4" diameter x 8" length for general purpose use. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1119 1¼" x 14" Pro Duty Driver Handle 1¼" diameter x 14" usable length for deep-seated seals & bearings. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1802 Bearing Cup Installer for Inner or Outer Wheel Bearing Cup on most Jeep Dana 44 closed Knuckle Front Axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1035 Differential Press Step Plate is used as a push plate for bearing removal or to support the differential when pressing on new bearings. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT5500 Wheel Bearing Packer Takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your Jeep 4x4! More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1115 Dana 44 Differential Side Bearing Installer for Dana-Spicer Model 44 4x4 front axles. QT1115 features a raised internal ring that contacts the bearing inner face so you can press or drive your diff bearings on without damaging the cage. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1032 Case Spreader Is used to relieve the differential bearing preload making it easy to safely remove and install your front differential without damaging expensive critical parts. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT1024 4x4 Triple Metric and Standard Thread Universal Spindle Puller Use with any 5/8" fine thread slide hammer to quickly and easily remove those rusted in front wheel bearing spindles on your 1957-1973 Jeep Dana 44 Front Axle without damage! Essential for servicing axle u-joints, king pins, spindle bearings, inner axle seals, and differentials. More Info

photo

QT1200i Tie Rod Separator Allows you to remove the separate tie rod and drag link ends without wrecking the seals or screwing up your steering linkage ends. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QT9018 5 Pound Dead Blow Hammer Is just about the first tool you will reach for to do a multitude of jobs on your Chevy 4x4. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool. Discontinued. More Info

photo

QT1097 Differential Master Bearings For 1967-1973 Jeep Dana 44 axles slips on your differential in place of the taper bearings and cups. Used along with a dial indicator to determine the correct differential shim thickness. Discontinued. More Info

Wheel Bearings and Seals (Individual)

top_page
photo

QU50704 4x4 Front Wheel Grease Seal for Dana 44 front axles 1969-1973 Jeep (8000# GVW), 4x4 trucks with Dana 44 front axles and wheel hubs that use 3-3/4" bolt circle external mount lockout hubs or drive flanges. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50702 Timken® Tapered Wheel Bearing for Dana 44 front axles 1969-1973 Jeep (8000# GVW) 4x4 trucks. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50703 Timken® Inner Wheel Bearing for Dana 44 front axles 1969-1973 Jeep (8000# GVW) 4x4 trucks with Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!
photo

QU50701 Timken® Inner or Outer Wheel Bearing Cup for Jeep Dana 44 front axles 1969-1973 (8000# GVW) 4x4 trucks with Dana 44 front axles. More Info

Yes
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

Wheel Bearing and Seal Kits

top_page

TK4926 Torque King® Wheel Bearing and Seal Kit for 1969-1973 Jeep J4000, J4800, and Camper Special Dana 44 Front Axles Fits trucks with 1-3/4" thread hex spindle nuts and external mount wheel hubs. Kit includes 4 Timken® Bearings with Cups, 2 Front Wheel Seals, 2 Hub Gaskets, & 2 Bend Over Tab Lockwashers. More Info

Out of Stock
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!