Inner & Outer Wheel Bearing Cup Installer-QT1801

photo

QT1801 Wheel Bearing Cup Installer is used to install many of the Bearing Cups used in Chevy, Dodge, Ford, GMC, and Jeep full sized SUV's, 1/2, 3/4 and 1-ton trucks from 1968 to current. QT1801 fits our QU10125 (NV4500 Transmission), QU10137 (GM NV4500), QU12051 (NV5600 Transmission), QU50404 (axle pinions), QU50411 (wheel bearing), and QU50446 (wheel bearing) bearing cups. Precision CNC machined solid steel tool is drilled to accept any driver handle with a 5/8" tip. Made in U.S.A. Be sure to read Tech Notes below!

QT1801
Bearing Cup Installer
$23.97
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

tech note

Dan the Gear Man® Tech Note 1:
Using a Bearing Cup Installer not only saves time, but, more importantly, also allows you to install the bearing cup without damaging either the cup or bearing bore. Bearing Cup Installers are the key to damage free bearing cup installation. With one, you can completely seat those bearing cups without nicks or dings. Using the proper Cup Installer and Handle completely eliminates one of the most common causes of premature bearing failure, namely installation with punches or other makeshift tools.

tech note

Dan the Gear Man® Tech Note 2:
I recommend an 8" handle (QT1100, QT1116) for most applications and a 14" handle (QT1101, QT1119) for deep set inner pinion, rear hub and transmission bearing cups.

tech note

Dan the Gear Man® Tech Note 3:
As of May 1, 2011, QT1801 was redesigned to fit more applications. The current QT1801 replaces our previous QT1801, QT1817 and QT1823 tools. The new QT1801 Installer is made to install all these Timken® Taper Bearing Cup numbers: JLM104910, LM104911, LM104911-A, LM104912, NP728109, M802011, M802011AP, and NP882000. QT1801 Installers sold before that date only work on JLM104910, LM104911, LM104911A, and LM104912.

tech note

Dan the Gear Man® Tech Note 4:
Matching Parts for QT1801 Installer for NV4500 Transmissions:
QU10125 Timken High Performance Input Bearing Cup
QU10124 Timken High Performance Input Bearing
QU10126 Input Seal
QU10100 Bearing Retainer Bolt with factory applied RTV sealant
QU51002 Clutch Release Bearing
NV4500E Low Ratio Transmission Case for 1996 GM and 1994-1996 Dodge
NV4500L High Ratio Transmission Case for 1997 and Newer GM and Dodge
QU10076 Rebuilder Spec NV4500HD Input Shaft
QU10199 Replacement NV4500HD Input Shaft
QU11238 Input Bearing Retainer
QU90003 Anerobic Sealant
QU90006 3.35 oz Ultra Black RTV Sealant
QU90005 0.5 oz Ultra Black RTV Sealant
S24200 6ml Threadlocker
S9978 1 gram Threadlocker
QU90020 NV4500 Manual Transmission Oil
TM1003 NV4500 Shop Manual
V1003DVD NV4500 Overhaul Video

Application

QT1801 Applications:

Use QT1801 Cup Installer for These 4x4 Front Inner Wheel Bearing Cup Applications
Chevy and GMC:
K10, K15, K1500 1/2 ton Pickup 1977½-1987
K20, K25, and K2500 3/4 ton Pickup 1977½-1987

Dodge and Plymouth:
Ramcharger, Trailduster, W150, W250 with gas engine 1980-1993

Use QT1801 Cup Installer for These Front Outer Wheel Bearing Cup Applications
Chevy/GMC:
K30, K35, V30, V3500 Model 60 Axle 1977-1991

Dodge:
W300, W350 1975-1993
W250 Diesel 1989-1993

Ford:
F350 1979-97
F250 w/Model 601978-79
F250 w/Model 50 IFS 1980-97
Bronco & F150 1987-1991 Model 44IFS Axle Tag #'s 610267, 610309, 610311

Use QT1801 Cup Installer for These Rear Outer Wheel Bearing Cup Applications
Chevy/GMC:
3/4 & 1 Ton C/K/G Full Float Rear 1973-2007 Axle (Use flat side)

Dodge:

All 3/4 and 1-ton trucks 1977-2010
1972-1979 D200, W200, and D300 Truck Dana 60, Dana 60HD Full Float Rear Axle See Application Chart 1 & 2
1972-1979, 1978-1979 Plymouth 3/4 ton and 1-ton vans and van chassis vehicles equipped with either Dana Spicer Model 60 5,500 pound rated single rear wheel or Dana Spicer Model 60HD 5,800 or 6,200 pound rated single or dual rear wheel full-floating rear drive axles See Application Chart 3 & 4

Ford:
F-250, F-350 1968-current (except Dana 80)
1999-2004 F350, F450 with Dana 80 Dual Rear Wheel Rear Axle
2005-2010 F350 with Dana 80 Dual Rear Wheel Rear Axle

Use QT1801 Cup Installer for These Rear Inner Wheel Bearing Cup Applications
Dodge:
Light duty 3/4 ton with Dana 60 & gasoline engine 1977-1993

Ford:

F-250 1968-1984 Most with Dana 60 Rear

Toyota:
Land Cruiser with full float rear axle 1975-1997

QT1801 Transmission Applications:
New Venture NV4500 5 speed, GM and Dodge 1992-2007 all Input Bearing Cup
New Venture NV5600 6 speed, all 1999-2005 Dodge Countershaft Center Bearing Cup

QT1801 Axle Pinion Applications:
AMC/Jeep Model 20 Rear
Dana-Spicer Model 60, 61 Front or Rear Axles
Dana 80 Outer Pinion Bearing
Ford 7.5" Rear Axle
GM 8.25: IFS Front Axle
GM 8.5" Front or Rear Axles
GM 8.6", 8.875" Rear Axles