QU40025 Dana Closed Knuckle Axle Shaft Bushing

photo

QU40025 Medium Spindle and Axle Shaft Bushing for Dana Spicer Closed Knuckle Axles is a genuine original equipment flanged Bronze Bushing that is primarily found in the spindle of Dana Spicer closed knuckle front axles, plus you may also see them pressed in the end of 1960's Dana 44HD axle housing tubes to support the inner axle shafts. QU40025 was used by Chevy, Dodge, Ford, GM, International, and Studebaker to support the outer axle shaft in all Dana Spicer Model 44 and Model 44HD closed knuckle front axles. 1974-1975 Ford F-250 Crew Cab 4x4 trucks use a Dana 60 front axle which also has QU40025 Spindle Bushings. Order 2 or 4 Bushings per vehicle depending upon axle configuration. Made in U.S.A.

QU40025
Medium Dana Closed Knuckle Axle Shaft Support Bushing
$12.99
* Kits made up of multiple items may not show an inventory in-stock status but are almost always in stock!

tech note

Both the inside diameter and thrust face of the Bushings are subject to wear. Replace any installed bushing that is a loose fit to the axle shaft, that has visible wear, or is not a press-fit in the spindle. Worn out Bushings will cause the axle shaft to hit the King Pins.

tech note

Pre-Lube the inside of the bushing with some clean grease before installing the spindle to provide initial lubrication.

tech note

QU40025 has a nominal inside diameter of 1-3/8".

tech note

Matching Parts for QU40025 Spindle to Outer Axle Shaft Bushing:
QU40165 Outer Axle Shaft for many 1960-1975 Dana 44 Closed Knuckle Front Axles
QU40575 Outer Axle Shaft for many 1961-1975 Dana 44HD Closed Knuckle Front Axles
QU40598/QU40428/QU40657 Splined Hub Gears
QU56018 Warn Manual Lockout Hub Set
QU40032 Axle Shaft Snap Ring
QK4617 Knuckle Bearing and Shim Kit
QU40188 8 Bolt Knuckle Ball Seal
QU20267 Spindle for 1/2 Ton Dana 44 Closed Knuckle Front Axles with Internal Spline Wheel Hubs
QU20252 Spindle for 1/2 or 3/4 ton Ton Dana 44 Closed Knuckle Front Axles with External Mount Hub-Locks
QU90018 Pyroplex® Grease

Application

APPLICATIONS:

Chevrolet/GMC:
Closed Knuckle standard Dana 44

1960-1969 K10/K15, K20/K25
Closed Knuckle Dana 44HD
1963-1968 K20/K25

Dodge:
Closed Knuckle standard Dana 44

1957-1971 W100, W200
Closed Knuckle Dana 44HD
1963-1971 W200


Ford:
Closed Knuckle standard Dana 44:
1959-1966 F-100
1959-1975 F-250 with standard Model 44 Front Axle
Closed Knuckle Dana 44HD

1961-1975 F-250 with Heavy-Duty Model 44 Front Axle
Closed Knuckle Dana 60:
1973-1975 F-250 Crew Cab

International:
Closed Knuckle Dana 44:
1953-1975 1/2 ton and light 3/4 ton
Closed Knuckle Dana 44HD:
1953-1975 200, 1200 with Heavy-Duty Model 44 Front Axle

Studebaker:
Closed Knuckle standard Dana 44:
1957-1964 4x4 Pickups