Parts for Dana-Spicer Model 60 Rear Axles in 1966-1975 International Trucks
Page under construction, more parts will be added soon
Axle Identification
     
Dana 60 Diff CoverClick to Enlarge

Cover: 10 Bolt, 12" high

Ring Gear: 9-7/8", 12 Bolt

  
     
     
     
Axle Assemblies and Housings
  No Axle Assemblies or Housings in Stock  
     
     
Axle Shafts
  No Axle Shafts in Stock  
     
     
Brake Parts
  No Axle Brake Parts in Stock  
     
     
Differential and Pinion Bearings (Individual)
Over the years, Dana has primarily used Timken bearings when building their axles. For long life and dimensional consistency, Timken bearings are unmatched by any other brand of bearing I have used rebuilding axles over the past 30+ years in the business. When you are a shade tree mechanic dealing with a diff and pinion rebearing job without all the fancy gauging tools we have, you always want your new bearings to be the same overall thickness as the original bearings were when the axle was built so your pinion depth, pinion preload and backlash are within the tolerance limits when you are done with the job. Timken bearings will almost always deliver that type of accuracy, plus the steel quality and surface finish is the world's best.


Link to Vehicle Make or Category Links

QU50397 Timken® Differential Bearing Cup for 1966-1975 International 3/4 ton trucks with Dana 60 rear axles. (uses 2).


QU50398 Timken® Differential Bearing for 1966-1975 International 3/4 ton trucks with Dana 60 rear axles. (uses 2).

QU50400 Timken® Outer Pinion Bearing Cup for 1966-1975 International 3/4 ton trucks with Dana 60 rear axles.

QU50401 Timken® Outer Pinion Bearing for 1966-1975 International 3/4 ton trucks with Dana 60 rear axles.

QU50406 Timken® Inner Pinion Bearing Cup for 1966-1975 International 3/4 ton trucks with Dana 60 rear axles.


QU50407 Timken® Inner Pinion Bearing for 1966-1975 International 3/4 ton trucks with Dana 60 rear axles.
Check Out Now
Differential Bearing Kits
     
     
     
     
Differential Parts (Locking)
     
     
     
     
Differential Parts (Open)
     
     
     
     
     
     
     
     
     
Gaskets and Gasket Maker
Depending upon the year, a cut gasket or RTV sealant was used by Dana-Spicer to seal the differential cover. Early, thin gauge covers with embossed flanges are made for use with a cut gasket. Later thick gauge covers with flat flanges are designed for sealing with RTV or if you desire, you can use a combination of a cut gasket with thin films of RTV. We stock both genuine Dana Gaskets and Ultra Gray RTV Sealant which has high adhesion and excellent resistance to synthetic lubricants. Link to Our Jeep Web Page Index
QU40367 Rear Differential Cover Gasket Dana has replaced the Dana 60 Gasket with a Dana 70 Gasket. These genuine Dana-Spicer Model 70 gaskets will also work on your Dana 60 front axles if you wish to use a Gasket in lieu of RTV sealant. Made in U.S.A.

 
S82194 Ultra Gray RTV Sealant combines high adhesion and resistance to both conventional and synthetic gear lubes. The perfect choice to seal the differential cover on your Dodge Ram.
Check Out Now
Manuals and Technical Information
Dan the Gear Man® Product Note: Knowing how to do the job right the first time is half the battle. With our detailed, easy to read, and well illustrated technical publications, you get accurate service procedures, torque specifications, and tool recommendations. Link to Our Dodge Web Page Index
TM4400 Pinion and Differential Bearing Service On Dana-Spicer Monobeam Axles. covers step by step in text and photos the differential service procedures, specifications, and tools needed to replace differential and pinion bearings in Dana Spicer front or rear drive axles.
     
Check Out Now
Miscellaneous
Proper lubrication and replacing damaged or worn small parts is often the difference between a first class, long-term repair and a short lived nightmare. In this section are the small parts and accessory items that do not neatly fit under our other parts headings. Link to Our Dodge Web Page Index
S24200 Blue Threadlocker for spindle and ring gear bolts etc.
QU90008 Gear Marking Compound

use with QT9404 Brush to check your ring and pinion gear tooth pattern

 
Anti-Seize Lubricant use between the spindle and knuckle mating surfaces to prevent rust bonding.
PP14 Pyroplex® Protection ES Synthetic Grease provides extended service protection for king pin, axle universal joint, and wheel bearing applications under the harshest on and off road conditions!
SynPower® is a superior quality, moly-fortified, Synthetic Bearing/Chassis Grease for all U.S., European, and Japanese Vehicles.  Use on disc and drum brake wheel bearings, chassis, suspension, universal joints, and CV joints.
Syncon High Performance Synthetic Arctic Grease is an extreme pressure, premium quality, synthetic cold weather grease that provides exceptional protection for bearings and chassis components in sub-zero weather.
707L Red Grease is a premium, extreme pressure, high performance wheel bearing grease with special additives providing excellent rust protection and high resistance to water washout. 707L is an high quality, non-synthetic grease suitable for all 4x4 and light truck disc and drum brake wheel bearing applications, plus it is an ideal grease for chassis lubrication. Available in 14 oz. cartridge or 1 pound tub.
Check Out Now
Pinion Seals and Yokes
     
QU40097 Pinion Seal for Dana 60 Rear Axles. This genuine Dana-Spicer original equipment service part fits all 1966-1975 International 3/4 ton trucks with Dana 60 rear axles.
     
     
     
Ring and Pinion Kits
     
     
     
     
Small Parts
Sometimes, you just need one or two small parts to get back on the road. Between the small parts listed in this section and many others listed under part specific headings elsewhere on the page, we probably have that pesky little part you have to have but just can't find anywhere else. Link to Vehicle Make or Category Links
QU40343 Dana 60 Hardened Differential Cap Retaining Bolt Genuine original equipment hex-head bolt for all 1966-1975 International 3/4 ton trucks with Dana 60 rear axles.
QU40022 Dana 60 Pinion Nut Genuine original equipment pinion nut for 1966-1975 International 3/4 ton trucks with Dana 60 rear axles. QU40022 is a genuine original equipment, self-locking nut, intended for a single use part, discard and replace with a new nut any time you remove the pinion nut.

 
QU40023 Dana 60 Pinion Washer for Dodge Ram is a genuine original equipment flat washer goes between the pinion nut and pinion yoke. Fits all 1966-1975 International 3/4 ton trucks with Dana 60 rear axles.
QU40207 Dana 60 Differential and Pinion Shim Kit for1966-1975 International 3/4 ton trucks with Dana 60 rear axles. Genuine Dana-Spicer Shim Kit includes Pinion depth shims, pinion preload shims, differential adjusting shims, pinion nut, and cover gasket.

QU40206 Dana 60 Differential Bearing Shim Kit includes a selection of genuine original equipment Shims for adjusting backlash and differential bearing preload on your1966-1975 International 3/4 ton trucks with Dana 60 rear axles.
QU40099 Dana 60 Outer Pinion Slinger fits between the outer Pinion Bearing and Pinion Yoke. QU40099 is a genuine original equipment Dana Spicer part for 1966-1975 International 3/4 ton trucks with Dana 60 rear axles.
QU40086 Dana 60 Ring Gear Bolt for Dana 60. Genuine Dana-Spicer Grade 9 Bolt has locking teeth under the hex head to prevent loosening under any load conditions.

Dan the Gear Man® Safety Note: Ring Gear Bolts are designed for a single use. They must be replaced after they are removed!
     
Check Out Now
Spindle Nuts and Spindle Hardware
     
     
     
     
Tools
Having the right tool for the job makes the work easier and faster, plus the correct tool will usually minimize the chances of wrecking parts. We offer many special tools made specifically for the Dana 60 or Dana 61 front axle in your 1966-1975 IHC 3/4 ton. Link to Vehicle Make or Category Links
QT5500 Wheel Bearing Packer takes the mess out of packing wheel bearings, plus it minimizes the chances of getting contaminants mixed with your wheel bearing grease. The QT5500 Bearing Packer does an absolutely beautiful job of forcing grease between the individual bearing rollers. The easiest and most efficient way to repack the front wheel bearings on your 3/4 Ton Binder!
QT2005 Inner Pinion Bearing Installer is used to quickly and easily seat your OU50407 Inner Pinion Bearing on the pinion.
QT1805 Inner Pinion Bearing Cup Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50406 Inner Pinion Bearing Cup a simple and fast procedure.
QT1812 Outer Pinion Bearing Cup Installer Installer attaches to one of our QT1100 Series Driver Handles. Our precision CNC machined steel Installer is makes installing your QU50400 Outer Pinion Bearing Cup a simple and fast procedure.
QT1088 Differential Step Plate fits either side of the differential and are used to support the differential when installing your differential bearings or it acts as a push plate when you use a puller to remove the old bearings.
QT1158 Differential Bearing Installer makes a hard job easy. The raised inside ridge matches against inner differential bearing race allowing you to easily press or drive on QU50398 differential bearing until the bearing is fully seated against the differential adjusting shims.
QT1098 Differential Master Bearings slip on your differential in place of the taper bearings and cups. Used along with a dial indicator to determine the correct differential shim thickness.
     
QT1100 Series Driver Handles are used in conjunction with our seal and bearing cup installers

QT1033 Case Spreader is used to relieve the differential bearing preload making it easy to safely remove and install your front differential without damaging expensive critical parts.

QT9018 5 Pound Dead Blow Hammer is just about the first tool you will reach for for a multitude of jobs on your Dodge Ram. From seating differentials to removing rusted on wheels, the ability to apply persuasive force without damaging the reluctant part will make you wonder how you ever lived without this essential tool.

QT9302 5 Pound Slide Hammer a first-class tool for pulling just about anything you can get a matching 5/8" fine thread puller attachment for.
QT9404 Application Brush for Anti-Seize or Gear Marking Compound
Check Out Now
Wheel Bearings and Seals (Individual)
     
     
     
     
     
     
     
Wheel Bearing and Seal Kits